Study guide
12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
Key Takeaways Explain This Topic AI
Pure proportional control always leaves a steady-state offset: offset equals the difference between required output and the output at zero error, divided by the proportional gain.
Proportional gain is 100% output divided by the proportional band, so a 10 F proportional band on a 0 to 100% output corresponds to a gain of 10% per degree F.
Integral action eliminates offset by continuing to change the output as long as error persists; derivative action is rarely used in HVAC because process noise is amplified and most HVAC processes are slow and self-regulating.
Outdoor air reset of hot water supply temperature reduces distribution losses and enables condensing boiler operation by keeping return water below the roughly 130 F flue gas dew point.
Trim-and-respond static pressure and supply air temperature reset uses requests from terminal units to lower the setpoint until a zone complains, which typically saves far more fan energy than a fixed setpoint chosen at design conditions.
Last updated: August 2026
12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
Sub-topic 2D names two loop concepts explicitly: temperature reset and PID . This section develops both, plus the standard sequences that a mechanical PE is expected to be able to write and critique.
1. Control Modes, From Simplest to Most Capable
Mode Behavior Where It Belongs
Two-position (on/off) Output is fully on or fully off, with a differential to prevent chatter Unit heaters, exhaust fans, single-stage equipment
Floating (incremental) Output is driven open or closed while error exceeds a deadband, then held Slow processes with a well-matched actuator speed; no position feedback needed
Proportional (P) Output is proportional to error Fast, stable, but leaves permanent offset
Proportional + Integral (PI) Integral term accumulates error over time until it is zero The HVAC workhorse - discharge air temperature, static pressure, valve and damper loops
- PID Adds a derivative term responding to rate of change Rarely justified in HVAC; amplifies sensor noise
- 2. Proportional Control and Its Unavoidable Offset
Proportional gain and proportional band are reciprocals of each other: K = 100 % P B K = \frac{100\%}{PB} K = PB 100%
Output is then: Output = Bias + K × Error \text{Output} = \text{Bias} + K \times \text{Error} Output = Bias + K × Error
Worked Example - Calculating Offset
A hot water reheat valve is controlled by a proportional-only loop with a 10 F proportional band and a 72 F space setpoint . The controller is calibrated so that 50% valve position occurs at zero error . Gain is 100% / 10 F = 10% per F .
Suppose the actual heating load requires only 30% valve position to hold steady state:
- 30 = 50 + 10 x (72 - T)
- 20 = 10 x (72 - T)
- 72 - T = -2, so T = 74 F
The space settles 2 F above setpoint and stays there. This is offset, and no amount of patience fixes it: the loop is at equilibrium and reports no fault. Generalized: Offset = Output required − Output at zero error K \text{Offset} = \frac{\text{Output required} - \text{Output at zero error}}{K} Offset = K Output required − Output at zero error
Narrowing the proportional band raises the gain and shrinks the offset - but at some point the loop becomes unstable and hunts. Integral action resolves the dilemma by continuing to shift the output for as long as any error persists, driving offset to zero without requiring a high proportional gain. Integral is expressed in repeats per minute or as an integral time; too much integral produces overshoot and slow oscillation, too little leaves a sluggish approach to setpoint.
Direct vs. Reverse Acting
A direct-acting loop increases output as the measured variable rises (cooling valve on space temperature). A reverse-acting loop increases output as the measured variable falls (heating valve on space temperature). Getting this backwards produces a loop that drives to a hard stop and stays there - one of the most common commissioning findings, and easy to spot on an exam because the described behavior is always monotonic runaway rather than oscillation.
3. Reset Strategies
Reset means moving a setpoint in response to a second variable so the plant does no more work than the load requires.
Outdoor Air Reset of Hot Water Supply Temperature
- Outdoor Air Temperature Hot Water Supply Setpoint
- 0 F (design) 180 F
- 30 F 150 F
- 50 F 120 F
- 60 F (warm weather cutoff) Boilers off
Three benefits stack:
Distribution losses fall roughly in proportion to the difference between pipe and ambient temperature.
Control valve authority improves , because a lower supply temperature means the valve must be more open to deliver the same heat, moving operation off the top of the stroke.
Condensing boilers actually condense. Return water must fall below the roughly 130 F flue gas dew point for the latent heat to be recovered, so reset is not an optimization for a condensing plant - it is a precondition for the efficiency you paid for.
Chilled Water and Condenser Water Reset
Raising chilled water supply temperature in mild weather reduces the chiller lift and therefore its kW/ton. Lowering condenser water temperature does the same thing from the other end. Both must be bounded: raising chilled water temperature too far compromises dehumidification, and lowering condenser water below the chiller's minimum starves the expansion device and can trip the machine.
Supply Air Temperature and Static Pressure Reset - Trim and Respond
Modern sequences do not use a fixed relationship to outdoor temperature. Instead, each terminal unit generates a request when it cannot meet its zone setpoint, and the air handler trims its setpoint in the efficient direction each cycle until it receives requests, then responds by backing off: every T seconds:
- if requests <= ignored_count: setpoint = setpoint - trim_amount (efficient direction)
- else: setpoint = setpoint + respond_amount * (requests - ignored)
- clamp setpoint between min and max
Applied to duct static pressure, this drives the fan to the lowest pressure that still satisfies every box. Because fan power varies with roughly the cube of flow and static pressure setpoint drives the whole curve, the savings routinely exceed those of any other single control measure. This is the core of the ASHRAE Guideline 36 high-performance sequences.
4. Economizer Control
An airside economizer uses outdoor air as free cooling. The control question is the high-limit shutoff - when to stop.
- High-Limit Type Logic Where It Fits
- Fixed dry-bulb Disable above a fixed outdoor dry-bulb, e.g. 75 F Dry climates
- Differential dry-bulb Disable when outdoor dry-bulb exceeds return dry-bulb Simple, robust
- Fixed enthalpy Disable above a fixed outdoor enthalpy, e.g. 28 Btu/lb Humid climates
Differential enthalpy Disable when outdoor enthalpy exceeds return enthalpy Theoretically optimal, but depends on two humidity sensors that drift
The engineering trade is honest and appears on exams: enthalpy control is thermodynamically correct but sensor-dependent. Two drifting humidity sensors can produce worse real-world performance than a robust differential dry-bulb changeover, which is why several climate zones in ASHRAE Standard 90.1 prohibit or restrict certain high-limit types.
Integrated economizer operation - running the economizer simultaneously with mechanical cooling rather than locking out one or the other - is required by 90.1 for most equipment, because partial free cooling still displaces compressor work.
5. Sequences Worth Memorizing
AHU cooling sequence: in order of increasing energy cost, heating valve closed, then economizer dampers modulate, then mechanical cooling stages - with a single sequenced output and no overlap between heating and cooling.
Deadband: a zone must have a temperature range in which neither heating nor cooling operates. Simultaneous heating and cooling in a VAV box is an energy defect that a deadband exists to prevent.
Optimum start: the controller learns the building's warm-up and cool-down rates and starts equipment only as early as needed to reach setpoint at occupancy, rather than at a fixed hour.
Night setback and unoccupied cycling: setpoints widen, outdoor air dampers close entirely, and equipment cycles only to hold the setback limits.
Minimum on and off times: protect compressors from short-cycling, at the cost of some control precision.