Study guide
9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings
Key Takeaways Explain This Topic AI
Water chiller capacity is governed by the hydronic heat balance q ˙ = 500 × GPM CHW × ( T CHWR − T CHWS ) \dot{q} = 500 \times \text{GPM}_{\text{CHW}} \times (T_{\text{CHWR}} - T_{\text{CHWS}}) q ˙ = 500 × GPM CHW × ( T CHWR − T CHWS ) ; standard AHRI rating conditions specify 54 ∘ F 54^\circ\text{F} 5 4 ∘ F entering and 44 ∘ F 44^\circ\text{F} 4 4 ∘ F leaving chilled water ( 2.4 GPM/ton 2.4\text{ GPM/ton} 2.4 GPM/ton for a 10 ∘ F Δ T 10^\circ\text{F}\text{ }\Delta T 1 0 ∘ F Δ T ).
Chiller efficiency metrics are interconverted via kW/ton = 3.51685 COP = 12 EER \text{kW/ton} = \frac{3.51685}{\text{COP}} = \frac{12}{\text{EER}} kW/ton = COP 3.51685 = EER 12 ; total heat of rejection to the condenser is THR = Tons × 12 , 000 + kW input × 3 , 412.14 \text{THR} = \text{Tons} \times 12,000 + \text{kW}_{\text{input}} \times 3,412.14 THR = Tons × 12 , 000 + kW input × 3 , 412.14 .
AHRI Standard 550/590 Integrated Part-Load Value (IPLV.IP) weights four distinct operating points: 1 % 1\% 1% at 100 % 100\% 100% load ( 85 ∘ F 85^\circ\text{F} 8 5 ∘ F ECWT), 42 % 42\% 42% at 75 % 75\% 75% load ( 75 ∘ F 75^\circ\text{F} 7 5 ∘ F ECWT), 45 % 45\% 45% at 50 % 50\% 50% load ( 65 ∘ F 65^\circ\text{F} 6 5 ∘ F ECWT), and 12 % 12\% 12% at 25 % 25\% 25% load ( 65 ∘ F 65^\circ\text{F} 6 5 ∘ F ECWT).
For kW/ton \text{kW/ton} kW/ton , IPLV.IP uses a weighted harmonic mean: IPLV (kW/ton) = 1 0.01 A + 0.42 B + 0.45 C + 0.12 D \text{IPLV (kW/ton)} = \frac{1}{\frac{0.01}{A} + \frac{0.42}{B} + \frac{0.45}{C} + \frac{0.12}{D}} IPLV (kW/ton) = A 0.01 + B 0.42 + C 0.45 + D 0.12 1 ; for EER or COP, IPLV.IP uses an arithmetic mean: IPLV = 0.01 A + 0.42 B + 0.45 C + 0.12 D \text{IPLV} = 0.01 A + 0.42 B + 0.45 C + 0.12 D IPLV = 0.01 A + 0.42 B + 0.45 C + 0.12 D .
ASHRAE Standard 90.1 defines two compliance paths: Path A requires higher full-load efficiency (ideal for baseload chillers), while Path B permits lower full-load efficiency in exchange for aggressive part-load IPLV performance (ideal for VFD chillers with condenser water relief).
Last updated: August 2026
9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings
Water chillers are the cornerstone of commercial, institutional, and district central chilled water plants. A water chiller integrates the four primary refrigeration cycle components—compressor, condenser, expansion device, and evaporator—into a packaged machine engineered to produce cold water (typically 40 ∘ F 40^\circ\text{F} 4 0 ∘ F to 45 ∘ F 45^\circ\text{F} 4 5 ∘ F ) for building air conditioning or process cooling. On the PE Mechanical: HVAC and Refrigeration exam, chiller questions evaluate hydronic heat balances, energy efficiency unit conversions, part-load performance under AHRI Standard 550/590, and energy code compliance under ASHRAE Standard 90.1.
1. Chiller Capacity & Primary Hydronic Energy Balances
Chiller cooling capacity represents the rate of heat removed from the circulating chilled water loop: Q ˙ evap (Btu/hr) = m ˙ CHW ⋅ c p , water ⋅ ( T CHWR − T CHWS ) = 500 × GPM CHW × Δ T CHW \dot{Q}_{\text{evap}}\text{ (Btu/hr)} = \dot{m}_{\text{CHW}} \cdot c_{p,\text{water}} \cdot (T_{\text{CHWR}} - T_{\text{CHWS}}) = 500 \times \text{GPM}_{\text{CHW}} \times \Delta T_{\text{CHW}} Q ˙ evap (Btu/hr) = m ˙ CHW ⋅ c p , water ⋅ ( T CHWR − T CHWS ) = 500 × GPM CHW × Δ T CHW Cooling Capacity (Tons) = 500 × GPM CHW × ( T CHWR − T CHWS ) 12 , 000 = GPM CHW × Δ T CHW 24 \text{Cooling Capacity (Tons)} = \frac{500 \times \text{GPM}_{\text{CHW}} \times (T_{\text{CHWR}} - T_{\text{CHWS}})}{12,000} = \frac{\text{GPM}_{\text{CHW}} \times \Delta T_{\text{CHW}}}{24} Cooling Capacity (Tons) = 12 , 000 500 × GPM CHW × ( T CHWR − T CHWS ) = 24 GPM CHW × Δ T CHW +-----------------------------------------------------------------------------------------+
- | STANDARD AHRI 550/590 WATER-COOLED CHILLER RATING BASELINE |
- +-----------------------------------------------------------------------------------------+
- | Evaporator Entering Water Temp (CHWR): 54.0°F (12.2°C) |
- | Evaporator Leaving Water Temp (CHWS): 44.0°F (6.67°C) --> Delta_T = 10.0°F |
- | Chilled Water Flow Rate per Ton: 2.40 GPM/ton |
- | Condenser Entering Water Temp (ECWT): 85.0°F (29.4°C) |
- | Condenser Leaving Water Temp (LCWT): 95.0°F (35.0°C) --> Delta_T = 10.0°F |
- | Condenser Water Flow Rate per Ton: 3.00 GPM/ton |
- | Evaporator Waterside Fouling Factor: 0.00010 hr·ft²·°F/Btu |
- | Condenser Waterside Fouling Factor: 0.00025 hr·ft²·°F/Btu |
- +-----------------------------------------------------------------------------------------+
Condenser Heat Rejection Balance THR (Btu/hr) = Q ˙ evap + W ˙ comp = ( Tons × 12 , 000 ) + ( kW input × 3 , 412.14 ) \text{THR (Btu/hr)} = \dot{Q}_{\text{evap}} + \dot{W}_{\text{comp}} = (\text{Tons} \times 12,000) + (\text{kW}_{\text{input}} \times 3,412.14) THR (Btu/hr) = Q ˙ evap + W ˙ comp = ( Tons × 12 , 000 ) + ( kW input × 3 , 412.14 ) THR (Btu/hr) = 500 × GPM CW × ( T LCWT − T ECWT ) \text{THR (Btu/hr)} = 500 \times \text{GPM}_{\text{CW}} \times (T_{\text{LCWT}} - T_{\text{ECWT}}) THR (Btu/hr) = 500 × GPM CW × ( T LCWT − T ECWT ) GPM CW = ( Tons × 12 , 000 ) + ( kW × 3 , 412.14 ) 500 × ( T LCWT − T ECWT ) \text{GPM}_{\text{CW}} = \frac{(\text{Tons} \times 12,000) + (\text{kW} \times 3,412.14)}{500 \times (T_{\text{LCWT}} - T_{\text{ECWT}})} GPM CW = 500 × ( T LCWT − T ECWT ) ( Tons × 12 , 000 ) + ( kW × 3 , 412.14 )
2. Chiller Efficiency Metrics & Interconversions
Chiller efficiency is expressed in multiple imperial and metric engineering metrics: +-----------------------------------------------------------------------------------------+
- | CHILLER EFFICIENCY METRIC CONVERSION FORMULAS |
- +-----------------------------------------------------------------------------------------+
- | 3.51685 12.000 |
- | kW/ton = ------------ = ---------- |
- | COP EER |
- | |
- | 3.51685 EER |
- | COP = ------------ = ---------- |
- | kW/ton 3.41214 |
- | |
- | 12.000 |
- | EER = ------------ = 3.41214 * COP |
- | kW/ton |
- +-----------------------------------------------------------------------------------------+
- Practical Benchmarks by Compressor Architecture
Compressor Type Typical Capacity Range Full-Load Efficiency (kW/ton) Full-Load COP Part-Load IPLV (kW/ton)
Air-Cooled Scroll 20 to 180 Tons 1.10 − 1.30 kW/ton 1.10 - 1.30\text{ kW/ton} 1.10 − 1.30 kW/ton 2.70 − 3.20 2.70 - 3.20 2.70 − 3.20 0.75 − 0.90 kW/ton 0.75 - 0.90\text{ kW/ton} 0.75 − 0.90 kW/ton
Air-Cooled Screw 100 to 500 Tons 1.00 − 1.20 kW/ton 1.00 - 1.20\text{ kW/ton} 1.00 − 1.20 kW/ton 2.93 − 3.52 2.93 - 3.52 2.93 − 3.52 0.65 − 0.80 kW/ton 0.65 - 0.80\text{ kW/ton} 0.65 − 0.80 kW/ton
Water-Cooled Scroll 30 to 200 Tons 0.70 − 0.85 kW/ton 0.70 - 0.85\text{ kW/ton} 0.70 − 0.85 kW/ton 4.14 − 5.02 4.14 - 5.02 4.14 − 5.02 0.50 − 0.65 kW/ton 0.50 - 0.65\text{ kW/ton} 0.50 − 0.65 kW/ton
Water-Cooled Screw 100 to 600 Tons 0.58 − 0.70 kW/ton 0.58 - 0.70\text{ kW/ton} 0.58 − 0.70 kW/ton 5.02 − 6.06 5.02 - 6.06 5.02 − 6.06 0.40 − 0.55 kW/ton 0.40 - 0.55\text{ kW/ton} 0.40 − 0.55 kW/ton
Water-Cooled Centrifugal (Fixed Speed) 200 to 3,000+ Tons 0.52 − 0.62 kW/ton 0.52 - 0.62\text{ kW/ton} 0.52 − 0.62 kW/ton 5.67 − 6.76 5.67 - 6.76 5.67 − 6.76 0.45 − 0.55 kW/ton 0.45 - 0.55\text{ kW/ton} 0.45 − 0.55 kW/ton
Water-Cooled Centrifugal (VFD Mag-Bearing) 200 to 1,500 Tons 0.50 − 0.58 kW/ton 0.50 - 0.58\text{ kW/ton} 0.50 − 0.58 kW/ton 6.06 − 7.03 6.06 - 7.03 6.06 − 7.03 0.28 − 0.38 kW/ton 0.28 - 0.38\text{ kW/ton} 0.28 − 0.38 kW/ton
3. AHRI Standard 550/590 Integrated Part-Load Value (IPLV)
Commercial chillers operate at 100% design capacity for less than 1% to 2% of their total annual operating hours. The vast majority of runtime occurs between 40% and 75% load when outdoor wet-bulb temperatures are lower than design conditions. To reflect real-world annual energy consumption, AHRI Standard 550/590 established the Integrated Part-Load Value (IPLV.IP) rating.
AHRI Standard Part-Load Test Points +-----------------------------------------------------------------------------------------+
- | AHRI 550/590 IPLV.IP TEST CONDITIONS & TIMING WEIGHTS |
- +-------+-----------+----------------------+--------------------+-------------------------+
- | Point | Capacity | Water-Cooled ECWT | Air-Cooled Ambient | Time Weighting Fraction |
- +-------+-----------+----------------------+--------------------+-------------------------+
- | **A** | **100%** | **85.0°F (29.4°C)** | **95.0°F (35.0°C)**| **0.01 (1%)** |
- | **B** | **75%** | **75.0°F (23.9°C)** | **80.0°F (26.7°C)**| **0.42 (42%)** |
- | **C** | **50%** | **65.0°F (18.3°C)** | **65.0°F (18.3°C)**| **0.45 (45%)** |
- | **D** | **25%** | **65.0°F (18.3°C)** | **55.0°F (12.8°C)**| **0.12 (12%)** |
- +-------+-----------+----------------------+--------------------+-------------------------+
Condenser Water Relief: Notice that as chiller cooling load decreases from 100% down to 50%, entering condenser water temperature (ECWT) is allowed to drop from 85 ∘ F 85^\circ\text{F} 8 5 ∘ F down to 65 ∘ F 65^\circ\text{F} 6 5 ∘ F ( 1.0 ∘ F 1.0^\circ\text{F} 1. 0 ∘ F reduction in ECWT for every 2.5 % 2.5\% 2.5% drop in load). Below 50% load, ECWT is capped at a minimum of 65.0 ∘ F 65.0^\circ\text{F} 65. 0 ∘ F to prevent oil separation and refrigerant migration issues.
Mathematical Formulation of IPLV
1. When Efficiency is Expressed in EER or COP (Higher is Better): IPLV.IP = 0.01 A + 0.42 B + 0.45 C + 0.12 D \text{IPLV.IP} = 0.01 A + 0.42 B + 0.45 C + 0.12 D IPLV.IP = 0.01 A + 0.42 B + 0.45 C + 0.12 D
Where A , B , C , D A, B, C, D A , B , C , D are the measured EER or COP at 100 % , 75 % , 50 % , 25 % 100\%, 75\%, 50\%, 25\% 100% , 75% , 50% , 25% load.
2. When Efficiency is Expressed in kW/ton (Lower is Better):
Because kW/ton = 12 / EER \text{kW/ton} = 12 / \text{EER} kW/ton = 12/ EER , the weighted averaging must be performed on the reciprocal (weighted harmonic mean): IPLV.IP (kW/ton) = 1 0.01 A + 0.42 B + 0.45 C + 0.12 D \text{IPLV.IP (kW/ton)} = \frac{1}{\frac{0.01}{A} + \frac{0.42}{B} + \frac{0.45}{C} + \frac{0.12}{D}} IPLV.IP (kW/ton) = A 0.01 + B 0.42 + C 0.45 + D 0.12 1
Where A , B , C , D A, B, C, D A , B , C , D are the measured kW/ton \text{kW/ton} kW/ton values at 100 % , 75 % , 50 % , 25 % 100\%, 75\%, 50\%, 25\% 100% , 75% , 50% , 25% load.
Exam Calculation Trap: Never calculate IPLV in kW/ton \text{kW/ton} kW/ton using the direct linear formula 0.01 A + 0.42 B + 0.45 C + 0.12 D 0.01 A + 0.42 B + 0.45 C + 0.12 D 0.01 A + 0.42 B + 0.45 C + 0.12 D . Linear weighting on kW/ton \text{kW/ton} kW/ton produces mathematical errors of 8 % 8\% 8% to 15 % 15\% 15% . You must use the harmonic reciprocal equation above!
Non-Standard Part-Load Value (NPLV.IP)
When a chiller is selected to operate at design conditions differing from AHRI standard conditions (e.g., producing 42.0 ∘ F 42.0^\circ\text{F} 42. 0 ∘ F leaving chilled water instead of 44.0 ∘ F 44.0^\circ\text{F} 44. 0 ∘ F , or with 82.0 ∘ F 82.0^\circ\text{F} 82. 0 ∘ F entering condenser water), the identical formula is applied to calculate NPLV.IP using the non-standard entering water temperature schedule: ECWT = ECWT design − ( ECWT design − 65 ∘ F 100 − 50 ) × ( 100 % − % Load ) \text{ECWT} = \text{ECWT}_{\text{design}} - \left(\frac{\text{ECWT}_{\text{design}} - 65^\circ\text{F}}{100 - 50}\right) \times (100\% - \%\text{Load}) ECWT = ECWT design − ( 100 − 50 ECWT design − 6 5 ∘ F ) × ( 100% − % Load )
4. ASHRAE Standard 90.1 Chiller Compliance: Path A vs. Path B
ASHRAE Standard 90.1 ( Energy Standard for Buildings Except Low-Rise Residential ) mandates minimum full-load and part-load efficiency thresholds for water chillers. To accommodate different plant operating profiles, 90.1 provides two alternative compliance paths: +-----------------------------------------------------------------------------------------+
- | ASHRAE STANDARD 90.1 COMPLIANCE PHILOSOPHY: PATH A vs. PATH B |
- +-----------------------------------+-----------------------------------------------------+
- | PATH A (Full-Load Optimized) | PATH B (Part-Load / VFD Optimized) |
- +-----------------------------------+-----------------------------------------------------+
- | • Strict Full-Load Efficiency | • Relaxed Full-Load Efficiency |
- | • Modest Part-Load (IPLV) Target | • Highly Aggressive Part-Load (IPLV) Target |
- | • Best for: Constant-speed base- | • Best for: Variable-speed (VFD) chillers operating |
- | load chillers in data centers | in variable cooling load applications with |
- | or industrial process cooling. | condenser water temperature relief. |
- +-----------------------------------+-----------------------------------------------------+
- ASHRAE Standard 90.1 Minimum Efficiency Table (Representative Values)
Equipment Type & Size Range Path A: Min Full-Load Path A: Min IPLV Path B: Min Full-Load Path B: Min IPLV
Air-Cooled Chillers ( < 150 Tons < 150\text{ Tons} < 150 Tons ) ≥ 10.10 EER \ge 10.10\text{ EER} ≥ 10.10 EER ≥ 13.70 EER \ge 13.70\text{ EER} ≥ 13.70 EER ≥ 9.70 EER \ge 9.70\text{ EER} ≥ 9.70 EER ≥ 15.80 EER \ge 15.80\text{ EER} ≥ 15.80 EER
Air-Cooled Chillers ( ≥ 150 Tons \ge 150\text{ Tons} ≥ 150 Tons ) ≥ 10.10 EER \ge 10.10\text{ EER} ≥ 10.10 EER ≥ 14.00 EER \ge 14.00\text{ EER} ≥ 14.00 EER ≥ 9.70 EER \ge 9.70\text{ EER} ≥ 9.70 EER ≥ 16.10 EER \ge 16.10\text{ EER} ≥ 16.10 EER
Water-Cooled Positive Disp (Screw/Scroll) ( 150 − 300 Tons 150-300\text{ Tons} 150 − 300 Tons ) ≤ 0.660 kW/ton \le 0.660\text{ kW/ton} ≤ 0.660 kW/ton ≤ 0.540 kW/ton \le 0.540\text{ kW/ton} ≤ 0.540 kW/ton ≤ 0.740 kW/ton \le 0.740\text{ kW/ton} ≤ 0.740 kW/ton ≤ 0.400 kW/ton \le 0.400\text{ kW/ton} ≤ 0.400 kW/ton
Water-Cooled Centrifugal ( 300 − 600 Tons 300-600\text{ Tons} 300 − 600 Tons ) ≤ 0.560 kW/ton \le 0.560\text{ kW/ton} ≤ 0.560 kW/ton ≤ 0.500 kW/ton \le 0.500\text{ kW/ton} ≤ 0.500 kW/ton ≤ 0.590 kW/ton \le 0.590\text{ kW/ton} ≤ 0.590 kW/ton ≤ 0.360 kW/ton \le 0.360\text{ kW/ton} ≤ 0.360 kW/ton
Water-Cooled Centrifugal ( > 600 Tons > 600\text{ Tons} > 600 Tons ) ≤ 0.540 kW/ton \le 0.540\text{ kW/ton} ≤ 0.540 kW/ton ≤ 0.480 kW/ton \le 0.480\text{ kW/ton} ≤ 0.480 kW/ton ≤ 0.560 kW/ton \le 0.560\text{ kW/ton} ≤ 0.560 kW/ton ≤ 0.330 kW/ton \le 0.330\text{ kW/ton} ≤ 0.330 kW/ton
Key Code Rule: A chiller must comply with BOTH the full-load and part-load IPLV requirements of either Path A or Path B. Mixing Path A full-load with Path B IPLV is strictly prohibited.
5. Chiller Lift Reduction & VFD Energy Savings
The fundamental thermodynamic driver of part-load chiller efficiency is compressor lift reduction : Lift = P condenser, sat − P evaporator, sat ∝ T condenser, sat − T evaporator, sat \text{Lift} = P_{\text{condenser, sat}} - P_{\text{evaporator, sat}} \propto T_{\text{condenser, sat}} - T_{\text{evaporator, sat}} Lift = P condenser, sat − P evaporator, sat ∝ T condenser, sat − T evaporator, sat
When ambient wet-bulb temperature drops, the cooling tower produces colder condenser water ( 85 ∘ F → 75 ∘ F → 65 ∘ F 85^\circ\text{F} \to 75^\circ\text{F} \to 65^\circ\text{F} 8 5 ∘ F → 7 5 ∘ F → 6 5 ∘ F ). In a constant-speed centrifugal chiller, lowering the ECWT saves energy, but the compressor must throttle using inlet guide vanes, creating aerodynamic drag.
In a Variable Frequency Drive (VFD) chiller, reducing compressor speed directly matches the reduced pressure lift requirement according to the affinity laws ( H ∝ N 2 H \propto N^2 H ∝ N 2 , Power ∝ N 3 \text{Power} \propto N^3 Power ∝ N 3 ). At 50% load and 65 ∘ F 65^\circ\text{F} 6 5 ∘ F ECWT, a VFD centrifugal chiller can operate at 0.25 0.25 0.25 to 0.32 kW/ton 0.32\text{ kW/ton} 0.32 kW/ton (a COP exceeding 11.0 11.0 11.0 !).
6. Worked Example: Comprehensive Chiller Analysis & IPLV Calculation
Problem: A 600-ton water-cooled centrifugal chiller is evaluated for a commercial central plant. The measured performance data at AHRI Standard 550/590 test points are:
- Point A (100% Load, 600 Tons, 85°F ECWT): Power = 330.0 kW 330.0\text{ kW} 330.0 kW
- Point B (75% Load, 450 Tons, 75°F ECWT): Power = 189.0 kW 189.0\text{ kW} 189.0 kW
- Point C (50% Load, 300 Tons, 65°F ECWT): Power = 96.0 kW 96.0\text{ kW} 96.0 kW
- Point D (25% Load, 150 Tons, 65°F ECWT): Power = 54.0 kW 54.0\text{ kW} 54.0 kW
Find:
The specific power consumption ( kW/ton \text{kW/ton} kW/ton ) and COP at each test point ( A , B , C , D A, B, C, D A , B , C , D ).
The Integrated Part-Load Value in kW/ton \text{kW/ton} kW/ton ( IPLV.IP kW/ton \text{IPLV.IP}_{\text{kW/ton}} IPLV.IP kW/ton ).
The Integrated Part-Load Value in COP ( IPLV.IP COP \text{IPLV.IP}_{\text{COP}} IPLV.IP COP ).
Determine whether the chiller meets ASHRAE Standard 90.1 Path B requirements for a 600-ton centrifugal chiller (Full-Load ≤ 0.590 kW/ton \le 0.590\text{ kW/ton} ≤ 0.590 kW/ton , IPLV ≤ 0.360 kW/ton \le 0.360\text{ kW/ton} ≤ 0.360 kW/ton ).
Step-by-Step Solution:
Step 1: Compute specific power (kW/ton) and COP at each operating point.
Point A (100%): kW/ton A = 330.0 kW 600 tons = 0.5500 kW/ton \text{kW/ton}_A = \frac{330.0\text{ kW}}{600\text{ tons}} = 0.5500\text{ kW/ton} kW/ton A = 600 tons 330.0 kW = 0.5500 kW/ton COP A = 3.51685 0.5500 = 6.394 \text{COP}_A = \frac{3.51685}{0.5500} = 6.394 COP A = 0.5500 3.51685 = 6.394
Point B (75%): kW/ton B = 189.0 kW 450 tons = 0.4200 kW/ton \text{kW/ton}_B = \frac{189.0\text{ kW}}{450\text{ tons}} = 0.4200\text{ kW/ton} kW/ton B = 450 tons 189.0 kW = 0.4200 kW/ton COP B = 3.51685 0.4200 = 8.373 \text{COP}_B = \frac{3.51685}{0.4200} = 8.373 COP B = 0.4200 3.51685 = 8.373
Point C (50%): kW/ton C = 96.0 kW 300 tons = 0.3200 kW/ton \text{kW/ton}_C = \frac{96.0\text{ kW}}{300\text{ tons}} = 0.3200\text{ kW/ton} kW/ton C = 300 tons 96.0 kW = 0.3200 kW/ton COP C = 3.51685 0.3200 = 10.990 \text{COP}_C = \frac{3.51685}{0.3200} = 10.990 COP C = 0.3200 3.51685 = 10.990
Point D (25%): kW/ton D = 54.0 kW 150 tons = 0.3600 kW/ton \text{kW/ton}_D = \frac{54.0\text{ kW}}{150\text{ tons}} = 0.3600\text{ kW/ton} kW/ton D = 150 tons 54.0 kW = 0.3600 kW/ton COP D = 3.51685 0.3600 = 9.769 \text{COP}_D = \frac{3.51685}{0.3600} = 9.769 COP D = 0.3600 3.51685 = 9.769
Step 2: Calculate IPLV.IP in kW/ton using the harmonic weighting formula. Denominator = 0.01 A + 0.42 B + 0.45 C + 0.12 D \text{Denominator} = \frac{0.01}{A} + \frac{0.42}{B} + \frac{0.45}{C} + \frac{0.12}{D} Denominator = A 0.01 + B 0.42 + C 0.45 + D 0.12 Denominator = 0.01 0.5500 + 0.42 0.4200 + 0.45 0.3200 + 0.12 0.3600 \text{Denominator} = \frac{0.01}{0.5500} + \frac{0.42}{0.4200} + \frac{0.45}{0.3200} + \frac{0.12}{0.3600} Denominator = 0.5500 0.01 + 0.4200 0.42 + 0.3200 0.45 + 0.3600 0.12 Denominator = 0.018182 + 1.000000 + 1.406250 + 0.333333 = 2.757765 \text{Denominator} = 0.018182 + 1.000000 + 1.406250 + 0.333333 = 2.757765 Denominator = 0.018182 + 1.000000 + 1.406250 + 0.333333 = 2.757765 IPLV.IP (kW/ton) = 1 2.757765 = 0.3626 kW/ton \text{IPLV.IP (kW/ton)} = \frac{1}{2.757765} = 0.3626\text{ kW/ton} IPLV.IP (kW/ton) = 2.757765 1 = 0.3626 kW/ton
(Note: If calculated incorrectly using linear weighting: 0.01 ( 0.55 ) + 0.42 ( 0.42 ) + 0.45 ( 0.32 ) + 0.12 ( 0.36 ) = 0.0055 + 0.1764 + 0.1440 + 0.0432 = 0.3691 kW/ton 0.01(0.55) + 0.42(0.42) + 0.45(0.32) + 0.12(0.36) = 0.0055 + 0.1764 + 0.1440 + 0.0432 = 0.3691\text{ kW/ton} 0.01 ( 0.55 ) + 0.42 ( 0.42 ) + 0.45 ( 0.32 ) + 0.12 ( 0.36 ) = 0.0055 + 0.1764 + 0.1440 + 0.0432 = 0.3691 kW/ton , which is mathematically invalid).
Step 3: Calculate IPLV.IP in COP using linear weighting. IPLV.IP COP = 0.01 ( COP A ) + 0.42 ( COP B ) + 0.45 ( COP C ) + 0.12 ( COP D ) \text{IPLV.IP}_{\text{COP}} = 0.01(\text{COP}_A) + 0.42(\text{COP}_B) + 0.45(\text{COP}_C) + 0.12(\text{COP}_D) IPLV.IP COP = 0.01 ( COP A ) + 0.42 ( COP B ) + 0.45 ( COP C ) + 0.12 ( COP D ) IPLV.IP COP = 0.01 ( 6.394 ) + 0.42 ( 8.373 ) + 0.45 ( 10.990 ) + 0.12 ( 9.769 ) \text{IPLV.IP}_{\text{COP}} = 0.01(6.394) + 0.42(8.373) + 0.45(10.990) + 0.12(9.769) IPLV.IP COP = 0.01 ( 6.394 ) + 0.42 ( 8.373 ) + 0.45 ( 10.990 ) + 0.12 ( 9.769 ) IPLV.IP COP = 0.06394 + 3.51666 + 4.94550 + 1.17228 = 9.6984 ≈ 9.70 \text{IPLV.IP}_{\text{COP}} = 0.06394 + 3.51666 + 4.94550 + 1.17228 = 9.6984 \approx 9.70 IPLV.IP COP = 0.06394 + 3.51666 + 4.94550 + 1.17228 = 9.6984 ≈ 9.70
Check consistency: IPLV (kW/ton) = 3.51685 9.6984 = 0.3626 kW/ton \text{IPLV (kW/ton)} = \frac{3.51685}{9.6984} = 0.3626\text{ kW/ton} IPLV (kW/ton) = 9.6984 3.51685 = 0.3626 kW/ton (Exact match!).
Step 4: Check ASHRAE 90.1 Path B compliance.
Full-Load Requirement: 0.550 kW/ton ≤ 0.590 kW/ton 0.550\text{ kW/ton} \le 0.590\text{ kW/ton} 0.550 kW/ton ≤ 0.590 kW/ton ⟹ \implies ⟹ Complies (PASS)
Part-Load IPLV Requirement: 0.3626 kW/ton > 0.360 kW/ton 0.3626\text{ kW/ton} > 0.360\text{ kW/ton} 0.3626 kW/ton > 0.360 kW/ton ⟹ \implies ⟹ Marginally Fails (FAIL)
To achieve compliance under Path B, the manufacturer must slightly retrim impeller staging or optimize VFD tuning at 50% load to lower IPLV below 0.360 kW/ton 0.360\text{ kW/ton} 0.360 kW/ton , or evaluate under Path A ( 0.550 kW/ton ≤ 0.560 kW/ton 0.550\text{ kW/ton} \le 0.560\text{ kW/ton} 0.550 kW/ton ≤ 0.560 kW/ton and 0.363 kW/ton ≤ 0.500 kW/ton 0.363\text{ kW/ton} \le 0.500\text{ kW/ton} 0.363 kW/ton ≤ 0.500 kW/ton ⟹ \implies ⟹ Fully Complies under Path A! ).
7. NCEES Reference Handbook Navigation & Exam Tips
HVAC Section: Chillers & AHRI Ratings: Find standard IPLV weighting equation coefficients ( 0.01 , 0.42 , 0.45 , 0.12 0.01, 0.42, 0.45, 0.12 0.01 , 0.42 , 0.45 , 0.12 ).
Harmonic vs. Linear IPLV Rule: Always check whether the question asks for IPLV in kW/ton \text{kW/ton} kW/ton (harmonic mean) or EER / COP \text{EER} / \text{COP} EER / COP (linear weighted sum).
Path A vs Path B Code Identification: Path A is Full-Load optimized; Path B is Part-Load (VFD) optimized.