Study guide
11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves
Key Takeaways Explain This Topic AI
The valve flow coefficient ( C v C_v C v ) represents the volumetric flow of 60 ∘ F 60^\circ\text{F} 6 0 ∘ F water in GPM that creates a 1.0 psi 1.0\text{ psi} 1.0 psi pressure drop across the fully open valve: Q = C v Δ P / SG Q = C_v \sqrt{\Delta P / \text{SG}} Q = C v Δ P / SG .
Equal Percentage ( = % =\% = % ) control valve characteristics are paired with nonlinear cooling/heating coils to produce an overall linear thermal output response across valve stroke.
Valve Authority ( N = Δ P valve, 100% Δ P branch, total N = \frac{\Delta P_{\text{valve, 100\%}}}{\Delta P_{\text{branch, total}}} N = Δ P branch, total Δ P valve, 100% ) quantifies the ratio of wide-open valve pressure drop to total branch pressure drop; design authority should satisfy N ≥ 0.25 to 0.50 N \ge 0.25\text{ to }0.50 N ≥ 0.25 to 0.50 to prevent distortion into quick-opening behavior.
Two-way modulating control valves enable variable-flow distribution and pump energy savings, whereas three-way valves (mixing or diverting) maintain constant branch flow.
Pressure Independent Control Valves (PICVs) combine a dynamic differential pressure regulator with a modulating control valve, guaranteeing an effective valve authority of N = 1.0 N = 1.0 N = 1.0 under all dynamic system pressures.
Last updated: August 2026
11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves
Automatic control valves regulate the rate of hydronic fluid flow through heat transfer coils in response to temperature, humidity, or process controllers. Selecting the proper valve flow coefficient ( C v C_v C v ), inherent trim characteristic, and valve authority ( N N N ) ensures stable proportional-integral-derivative (PID) control, prevents actuator hunting, preserves chiller/boiler Δ T \Delta T Δ T , and minimizes pumping energy. On the PE Mechanical: HVAC and Refrigeration exam, engineers must perform precise C v C_v C v calculations, evaluate installed valve characteristic distortion, calculate valve authority ratios, and distinguish between two-way, three-way, and pressure-independent configurations.
1. Valve Flow Coefficient ( C v C_v C v ) & Governing Hydraulics
The flow capacity of a control valve is universally characterized by the Flow Coefficient ( C v C_v C v ) , defined as the volumetric flow rate of clean water at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F ( SG = 1.00 \text{SG} = 1.00 SG = 1.00 ) in gallons per minute ( GPM \text{GPM} GPM ) that passes through the fully open valve with a pressure drop of exactly 1.0 psi 1.0\text{ psi} 1.0 psi ( 2.31 ft w.g. 2.31\text{ ft w.g.} 2.31 ft w.g. ). +---------------------------------------------------------------------------------------------------------+
- | CONTROL VALVE HYDRAULIC EQUATIONS |
- +---------------------------------------------------------------------------------------------------------+
- | Flow Equation: Q = C_v * sqrt( Delta_P / SG ) |
- | |
- | Required Valve C_v: C_v = Q / sqrt( Delta_P / SG ) |
- | |
- | Valve Pressure Drop: Delta_P = SG * ( Q / C_v )^2 [psi] |
- | Delta_H = 2.31 * ( Q / C_v )^2 [ft w.g. for water, SG = 1.0] |
- +---------------------------------------------------------------------------------------------------------+
Where:
- Q Q Q = Volumetric flow rate ( GPM \text{GPM} GPM )
- C v C_v C v = Valve flow coefficient ( GPM/psi 0.5 \text{GPM/psi}^{0.5} GPM/psi 0.5 )
- Δ P \Delta P Δ P = Pressure drop across valve ports ( psi \text{psi} psi )
- Δ H \Delta H Δ H = Head loss across valve ( ft w.g. \text{ft w.g.} ft w.g. )
SG \text{SG} SG = Specific gravity of fluid ( 1.00 1.00 1.00 for water at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F ; ≈ 1.03 to 1.08 \approx 1.03\text{ to }1.08 ≈ 1.03 to 1.08 for glycol mixtures)
Choked Flow & Cavitation in Hydronic Valves
When water accelerates through the restricted valve orifice (vena contracta), static pressure drops to its minimum ( P vc P_{\text{vc}} P vc ). If P vc P_{\text{vc}} P vc falls below the water's saturation vapor pressure ( P v P_v P v ), vapor bubbles form (flashing). As fluid decelerates downstream, pressure recovers; if downstream pressure exceeds P v P_v P v , the vapor bubbles violently collapse against valve trim surfaces (cavitation), generating high-frequency noise, vibration, and severe pitting erosion.
Cavitation Index ( σ \sigma σ ): σ = P inlet, abs − P v P inlet, abs − P outlet, abs = P 1 − P v Δ P \sigma = \frac{P_{\text{inlet, abs}} - P_v}{P_{\text{inlet, abs}} - P_{\text{outlet, abs}}} = \frac{P_1 - P_v}{\Delta P} σ = P inlet, abs − P outlet, abs P inlet, abs − P v = Δ P P 1 − P v Cavitation occurs when σ < σ critical \sigma < \sigma_{\text{critical}} σ < σ critical (typically σ < 1.5 to 2.0 \sigma < 1.5\text{ to }2.0 σ < 1.5 to 2.0 ). To prevent cavitation, engineers must avoid excessive single-valve pressure drops in high-temperature hot water loops.
2. Inherent vs. Installed Valve Characteristic Curves
The inherent characteristic describes the relationship between valve flow capacity ( C v C_v C v ) and valve stem position (stroke, h / h max h/h_{\text{max}} h / h max ) under a constant pressure drop across the valve. Flow (% of Q_max)
- 100 + . - - - - - - [ Quick Opening ]
- | . - '
- | . - ' / [ Linear ]
- | . - ' /
- | . - ' / . - - [ Equal Percentage ]
- | . ' / . '
- 50 + / . '
- | / . '
- | / . '
- | /. '
- | / . '
- | /. '
- 0 +------------------------+-------------------------------------------> Valve Stroke (%)
- 0 50 100%
- A. The Three Inherent Flow Characteristics
Quick Opening: Provides maximum flow at low stem travel ( 80 % 80\% 80% flow at 25 % 25\% 25% stroke). Primarily used for two-position (on/off) isolation or safety dump bypass service.
Linear: Flow rate is directly proportional to stem stroke: Q Q max = h h max \frac{Q}{Q_{\text{max}}} = \frac{h}{h_{\text{max}}} Q max Q = h max h . Used in constant-pressure applications, steam coils, or liquid level control.
Equal Percentage ( = % =\% = % ): Equal increments of stem travel produce equal percentage changes in the existing flow rate: d Q d h = c ⋅ Q ⟹ Q = Q max ⋅ R ( h h max − 1 ) \frac{dQ}{dh} = c \cdot Q \implies Q = Q_{\text{max}} \cdot R^{\left(\frac{h}{h_{\text{max}}} - 1\right)} d h d Q = c ⋅ Q ⟹ Q = Q max ⋅ R ( h max h − 1 ) Where R R R is the valve rangeability ( R = Q max / Q min R = Q_{\text{max}} / Q_{\text{min}} R = Q max / Q min , typically 30 to 50 30\text{ to }50 30 to 50 ). At low stroke, small absolute changes occur; at high stroke, large absolute changes occur.
B. Why Equal Percentage Valves are Essential for Hydronic Coils
Hydronic cooling and heating coils exhibit a highly non-linear, concave-downward thermal heat transfer characteristic. Because the logarithmic mean temperature difference (LMTD) and turbulent tube heat transfer coefficients saturate early, 50 % 50\% 50% water flow delivers approximately 85 % to 90 % 85\%\text{ to }90\% 85% to 90% of total coil heat transfer . IDEAL THERMAL LINEARIZATION VIA EQUAL PERCENTAGE TRIM:
- [ Non-linear Coil Heat Transfer ] x [ Equal % Valve Flow Curve ] = [ Linear Installed Thermal Output ]
- (Concave Downward Response) (Convex Upward Response) (Direct Proportional Control)
- Thermal Output (%) Water Flow (%) Thermal Output (%)
- 100 + . - - - - - 100 + . - ' 100 + /
- | . ' | . - ' | /
- | / | . - ' | /
- 50 + / 50 + . - ' 50 + /
- |/ | . - ' | /
- 0 +----+----+----+----+ 0 +----+----+----+----+ 0 +----+----+----+----+
- 0 25 50 75 100 0 25 50 75 100 0 25 50 75 100
- Water Flow (%) Valve Stroke (%) Valve Stroke (%)
By pairing an Equal Percentage valve (convex upward) with a Hydronic Coil (concave downward), the non-linearities cancel each other out, producing an overall linear thermal response ( Q thermal ∝ valve stroke Q_{\text{thermal}} \propto \text{valve stroke} Q thermal ∝ valve stroke ) essential for stable PID loop tuning.
3. Valve Authority ( N N N ) & Installed Characteristic Distortion
In an actual operating piping circuit, the pressure drop across the control valve is not constant . As the valve closes, total circuit flow decreases, causing friction losses in the coil and piping to decrease towards zero. Consequently, the differential pressure across the closing valve increases toward the total available pump head.
Mathematical Definition of Valve Authority ( N N N )
Valve Authority ( N N N ) (also designated as a a a ) is the ratio of the pressure drop across the fully open control valve at design flow to the total pressure drop across the entire variable-flow branch circuit (valve + coil + balance valve + branch piping): N = Δ P valve, 100% Δ P branch, total = Δ P valve, 100% Δ P valve, 100% + Δ P coil + Δ P piping \mathbf{N = \frac{\Delta P_{\text{valve, 100\%}}}{\Delta P_{\text{branch, total}}} = \frac{\Delta P_{\text{valve, 100\%}}}{\Delta P_{\text{valve, 100\%}} + \Delta P_{\text{coil}} + \Delta P_{\text{piping}}}} N = Δ P branch, total Δ P valve, 100% = Δ P valve, 100% + Δ P coil + Δ P piping Δ P valve, 100% +---------------------------------------------------------------------------------------------------------+
- | VALVE AUTHORITY DESIGN BOUNDARIES |
- +-----------------------+---------------------------------------------------------------------------------+
- | Authority Ratio (N) | Operational Control Impact |
- +-----------------------+---------------------------------------------------------------------------------+
- | **N >= 0.50** | **Ideal Design Standard:** Inherent equal percentage curve is minimally |
- | (50% to 100%) | distorted; provides precise, stable modulating control across full load range. |
- +-----------------------+---------------------------------------------------------------------------------+
- | **0.25 <= N < 0.50** | **Acceptable Commercial Range:** Slight distortion towards linear; acceptable |
- | | control for typical variable-speed distribution systems. |
- +-----------------------+---------------------------------------------------------------------------------+
- | **N < 0.25** | **Unacceptable (Oversized Valve):** Inherent equal percentage curve distorts |
- | (Severe Distortion) | into a Quick Opening profile. Valve acts like an on/off switch near the seat, |
- | | causing violent temperature hunting, valve wear, and Low Delta-T Syndrome. |
- +-----------------------+---------------------------------------------------------------------------------+
Mathematical Relation for Installed Flow: Q installed ( h ) = Q design 1 + N [ ( C v , max C v ( h ) ) 2 − 1 ] Q_{\text{installed}}(h) = \frac{Q_{\text{design}}}{\sqrt{1 + N \left[ \left(\frac{C_{v,\text{max}}}{C_v(h)}\right)^2 - 1 \right]}} Q installed ( h ) = 1 + N [ ( C v ( h ) C v , max ) 2 − 1 ] Q design INSTALLED CHARACTERISTIC SHIFT AS AUTHORITY (N) DECREASES:
- Flow (%)
- 100 +--------------------------------------------/ (N = 0.50 - Proper Equal % Curve)
- | . -'
- | . - '
- | . - - '
- | . - - ' (N = 0.10 - Distorts to Quick Opening!)
- | . - - '
- | . - - '
- 50 + '
- |
- |
- 0 +------------------------+-------------------------------------------> Stroke (%)
- 0 50 100%
When N = 0.10 N = 0.10 N = 0.10 (valve pressure drop is only 10 % 10\% 10% of branch total), an Equal Percentage valve behaves as a Quick Opening valve , releasing over 70 % 70\% 70% of design flow at only 20 % 20\% 20% stem travel.
4. 2-Way vs. 3-Way Valves & Pressure Independent Valves (PICV) +---------------------------------------------------------------------------------------------------------+
- | CONTROL VALVE ARCHITECTURE COMPARISON |
- +-----------------------+-----------------------------+---------------------------------------------------+
- | Valve Type | Flow Modulated | Primary Applications & Mechanical Behavior |
- +-----------------------+-----------------------------+---------------------------------------------------+
- | **2-Way Modulating** | Variable coil flow; | Standard for variable-volume primary and |
- | | variable system flow | secondary systems; requires VFD pumps. |
- +-----------------------+-----------------------------+---------------------------------------------------+
- | **3-Way Mixing** | Variable coil flow; | Two inlets, one common outlet. Constant total |
- | | constant system loop flow | loop flow; installed on coil RETURN line. |
- +-----------------------+-----------------------------+---------------------------------------------------+
- | **3-Way Diverting** | Variable coil flow; | One common inlet, two outlets. Constant total |
- | | constant system loop flow | loop flow; installed on coil SUPPLY line. |
- +-----------------------+-----------------------------+---------------------------------------------------+
- | **PICV (Pressure** | Variable coil flow; | Combines DP regulator, control valve, and balance |
- | **Independent)** | constant N = 1.0 authority | valve; immune to upstream/downstream pressure. |
+-----------------------+-----------------------------+---------------------------------------------------+ 3-WAY VALVE CONFIGURATIONS:
3-WAY MIXING (Installed on Return): 3-WAY DIVERTING (Installed on Supply):
2 Inlets (A & B) -> 1 Common Outlet (AB) 1 Common Inlet (AB) -> 2 Outlets (A & B)
- From Supply ===> [ COIL ] ===> Port A From Supply ===> Port AB ===+===> [ COIL ] ===> Return
- | | (Port A)
- v v
- [ MIXING ] ===> Return [ DIVERT ] ===> Bypass Pipe
- ^
- | (Port B)
- Bypass Pipe ================= Port B
- Pressure Independent Control Valves (PICVs)
A Pressure Independent Control Valve (PICV) integrates three mechanical devices into a single valve body:
An internal modulating control valve (actuated by DDC/thermostat).
An internal mechanical differential pressure regulator (spring-loaded diaphragm).
An adjustable flow limiter / manual balance valve. +---------------------------------------------------------------------------------------------------------+
- | HOW A PICV REGULATES SYSTEM FLOW |
- +---------------------------------------------------------------------------------------------------------+
- | 1. System pressure fluctuations (caused by other valves opening/closing) act on the internal diaphragm. |
- | 2. The diaphragm automatically adjusts an internal variable orifice to absorb the pressure variation, |
- | maintaining a constant Delta_P across the control valve plug at all times. |
- | 3. Because Delta_P across the control plug is held perfectly constant: |
- | |
- | Valve Authority is ALWAYS N = 1.0 (100%) |
- | |
- | 4. Hunting, overflow, dynamic balancing labor, and Low Delta-T Syndrome are completely eliminated. |
- +---------------------------------------------------------------------------------------------------------+
- 5. Worked Engineering Calculation: Control Valve Sizing & Authority
- Problem Statement
An air handling unit (AHU) chilled water cooling coil delivers 600 , 000 Btu/hr 600,000\text{ Btu/hr} 600 , 000 Btu/hr of sensible and latent cooling. Chilled water enters the coil at 44.0 ∘ F 44.0^\circ\text{F} 44. 0 ∘ F and leaves at 56.0 ∘ F 56.0^\circ\text{F} 56. 0 ∘ F ( Δ T = 12.0 ∘ F \Delta T = 12.0^\circ\text{F} Δ T = 12. 0 ∘ F ). The fluid is clean water ( SG = 1.00 \text{SG} = 1.00 SG = 1.00 ).
Hydraulic piping data for the branch circuit:
Cooling coil pressure drop at design flow: Δ P coil = 5.80 psi \Delta P_{\text{coil}} = 5.80\text{ psi} Δ P coil = 5.80 psi ( 13.40 ft w.g. 13.40\text{ ft w.g.} 13.40 ft w.g. )
Branch circuit piping, isolation valves, and strainer drop: Δ P piping = 1.70 psi \Delta P_{\text{piping}} = 1.70\text{ psi} Δ P piping = 1.70 psi ( 3.93 ft w.g. 3.93\text{ ft w.g.} 3.93 ft w.g. )
Target design valve authority: N = 0.50 N = 0.50 N = 0.50 (50%)
Available commercial equal-percentage 2-way control valves have the following standard rated C v C_v C v values: Available C v : [ 25.0 , 35.0 , 45.0 , 60.0 , 80.0 ] \text{Available } C_v: \quad [\, 25.0, \; 35.0, \; 45.0, \; 60.0, \; 80.0 \,] Available C v : [ 25.0 , 35.0 , 45.0 , 60.0 , 80.0 ]
Calculate:
The design water flow rate ( Q Q Q ) in GPM.
The ideal target valve pressure drop ( Δ P valve, target \Delta P_{\text{valve, target}} Δ P valve, target ) and target C v C_v C v .
Select the closest standard commercial valve C v C_v C v and compute the actual wide-open valve pressure drop ( Δ P valve, actual \Delta P_{\text{valve, actual}} Δ P valve, actual ).
Compute the actual installed valve authority ( N actual N_{\text{actual}} N actual ) and verify if it satisfies engineering standards.
Step-by-Step Solution
Step 1: Calculate Design Water Flow Rate ( Q Q Q ) q ˙ = 500 ⋅ Q ⋅ Δ T ⟹ Q = q ˙ 500 ⋅ Δ T \dot{q} = 500 \cdot Q \cdot \Delta T \implies Q = \frac{\dot{q}}{500 \cdot \Delta T} q ˙ = 500 ⋅ Q ⋅ Δ T ⟹ Q = 500 ⋅ Δ T q ˙ Q = 600 , 000 Btu/hr 500 × 12.0 ∘ F = 600 , 000 6 , 000 = 100.0 GPM Q = \frac{600,000\text{ Btu/hr}}{500 \times 12.0^\circ\text{F}} = \frac{600,000}{6,000} = \mathbf{100.0\text{ GPM}} Q = 500 × 12. 0 ∘ F 600 , 000 Btu/hr = 6 , 000 600 , 000 = 100.0 GPM
Step 2: Determine Target Valve Δ P \Delta P Δ P and Target C v C_v C v
Total circuit resistance excluding the valve: Δ P circuit = Δ P coil + Δ P piping = 5.80 psi + 1.70 psi = 7.50 psi \Delta P_{\text{circuit}} = \Delta P_{\text{coil}} + \Delta P_{\text{piping}} = 5.80\text{ psi} + 1.70\text{ psi} = 7.50\text{ psi} Δ P circuit = Δ P coil + Δ P piping = 5.80 psi + 1.70 psi = 7.50 psi
Applying the valve authority definition for N = 0.50 N = 0.50 N = 0.50 : N = Δ P valve Δ P valve + Δ P circuit = 0.50 ⟹ Δ P valve, target = Δ P circuit = 7.50 psi N = \frac{\Delta P_{\text{valve}}}{\Delta P_{\text{valve}} + \Delta P_{\text{circuit}}} = 0.50 \implies \Delta P_{\text{valve, target}} = \Delta P_{\text{circuit}} = \mathbf{7.50\text{ psi}} N = Δ P valve + Δ P circuit Δ P valve = 0.50 ⟹ Δ P valve, target = Δ P circuit = 7.50 psi
Calculate target flow coefficient ( C v C_v C v ): C v , target = Q Δ P valve / SG = 100.0 GPM 7.50 / 1.00 = 100.0 2.7386 = 36.51 C_{v,\text{target}} = \frac{Q}{\sqrt{\Delta P_{\text{valve}} / \text{SG}}} = \frac{100.0\text{ GPM}}{\sqrt{7.50 / 1.00}} = \frac{100.0}{2.7386} = \mathbf{36.51} C v , target = Δ P valve / SG Q = 7.50/1.00 100.0 GPM = 2.7386 100.0 = 36.51
Step 3: Select Standard Valve and Compute Actual Δ P valve \Delta P_{\text{valve}} Δ P valve
From the available commercial options ( [ 25 , 35 , 45 , 60 , 80 ] [25, 35, 45, 60, 80] [ 25 , 35 , 45 , 60 , 80 ] ), the closest standard size is C v = 35.0 C_v = 35.0 C v = 35.0 .
Compute actual wide-open pressure drop with C v = 35.0 C_v = 35.0 C v = 35.0 : Δ P valve, actual = SG ⋅ ( Q C v ) 2 = 1.00 × ( 100.0 35.0 ) 2 = ( 2.8571 ) 2 = 8.16 psi ( 18.86 ft w.g. ) \Delta P_{\text{valve, actual}} = \text{SG} \cdot \left(\frac{Q}{C_v}\right)^2 = 1.00 \times \left(\frac{100.0}{35.0}\right)^2 = (2.8571)^2 = \mathbf{8.16\text{ psi}} \quad (18.86\text{ ft w.g.}) Δ P valve, actual = SG ⋅ ( C v Q ) 2 = 1.00 × ( 35.0 100.0 ) 2 = ( 2.8571 ) 2 = 8.16 psi ( 18.86 ft w.g. )
(Note: If an engineer improperly selected the oversized C v = 60.0 C_v = 60.0 C v = 60.0 valve, the valve drop would plummet to ( 100 / 60 ) 2 = 2.78 psi (100/60)^2 = 2.78\text{ psi} ( 100/60 ) 2 = 2.78 psi ) .
Step 4: Calculate Actual Installed Valve Authority ( N actual N_{\text{actual}} N actual ) Δ P branch, total = Δ P valve, actual + Δ P circuit = 8.16 psi + 7.50 psi = 15.66 psi \Delta P_{\text{branch, total}} = \Delta P_{\text{valve, actual}} + \Delta P_{\text{circuit}} = 8.16\text{ psi} + 7.50\text{ psi} = 15.66\text{ psi} Δ P branch, total = Δ P valve, actual + Δ P circuit = 8.16 psi + 7.50 psi = 15.66 psi N actual = Δ P valve, actual Δ P branch, total = 8.16 psi 15.66 psi = 0.521 ( 52.1 % ) N_{\text{actual}} = \frac{\Delta P_{\text{valve, actual}}}{\Delta P_{\text{branch, total}}} = \frac{8.16\text{ psi}}{15.66\text{ psi}} = \mathbf{0.521} \quad (\mathbf{52.1\%}) N actual = Δ P branch, total Δ P valve, actual = 15.66 psi 8.16 psi = 0.521 ( 52.1% )
Engineering Conclusion: The selected C v = 35.0 C_v = 35.0 C v = 35.0 valve achieves an actual authority of 52.1 % 52.1\% 52.1% , perfectly satisfying the target design standard ( N ≥ 0.50 N \ge 0.50 N ≥ 0.50 ). The installed characteristic will maintain its equal percentage profile with virtually zero distortion, ensuring stable PID modulation across the full operating range.
6. NCEES Reference Handbook Navigation Strategies
Valve Flow Equations: Look up Q = C v Δ P / S G Q = C_v \sqrt{\Delta P / SG} Q = C v Δ P / SG and Δ P = S G ( Q / C v ) 2 \Delta P = SG (Q / C_v)^2 Δ P = SG ( Q / C v ) 2 in the Hydraulics / Fluids section. Remember that pressure drop Δ P \Delta P Δ P is in psi , while head loss Δ H \Delta H Δ H is in feet of water ( Δ H = 2.31 × Δ P \Delta H = 2.31 \times \Delta P Δ H = 2.31 × Δ P ).
Specific Gravity (SG) Conversions: For glycol mixtures (propylene or ethylene glycol), always incorporate fluid specific gravity ( SG > 1.0 \text{SG} > 1.0 SG > 1.0 ) into C v C_v C v calculations; omitting SG \text{SG} SG leads to undersized control valves.
Valve Authority Definition: Search "Valve Authority" ( N = Δ P valve / Δ P total N = \Delta P_{\text{valve}} / \Delta P_{\text{total}} N = Δ P valve /Δ P total ). Remember that total branch drop in the denominator MUST include the valve's own pressure drop.