Study guide
7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
Key Takeaways Explain This Topic AI
Cold storage refrigeration load has six components: transmission through the envelope, infiltration and air change, product load, respiration heat for living produce, internal gains from people, lights, motors and forklifts, and defrost heat.
Product load below the freezing point is calculated in three steps: sensible cooling above freezing with cp_above, latent heat of fusion at the freezing point, and sensible cooling below freezing with cp_below, which is roughly half of cp_above.
Lean beef uses approximately cp_above = 0.77 Btu/lb-F, cp_below = 0.40 Btu/lb-F, latent heat of fusion of 100 Btu/lb, and a freezing point near 28 F; most food freezing points sit below 32 F because of dissolved solids.
Compressor capacity is sized on daily load divided by design run hours, typically 16 to 18 hours per day rather than 24, so a 24-hour load must be divided by roughly 0.70 to obtain required equipment capacity.
Evaporator temperature difference sets storage relative humidity: an 8 F to 10 F TD holds about 90% to 95% RH for unwrapped produce, while a 15 F to 20 F TD dries product and is reserved for packaged goods.
Last updated: August 2026
7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
NCEES sub-topic 2E names "food processing and storage" explicitly among the refrigeration systems you must be able to work. This is the part of refrigeration practice that comfort-cooling engineers most often skip, and it is also the part where the arithmetic is most different: a cold room load is dominated by the product , not by the envelope, and the design question is usually "how fast" rather than "how cold."
1. The Six Components of a Cold Storage Load
- Component Driver Typical Share
- Transmission UA times the temperature difference across insulated walls, ceiling, floor 10% to 25%
Infiltration / air change Door openings, dock leakage, air curtains; enthalpy difference times mass flow 10% to 30%
- Product Sensible cooling, freezing, and sub-freezing sensible cooling of the goods 30% to 60%
- Respiration Living produce continues to metabolize and generate heat in storage 0% to 15%
- Internal gains Lights, evaporator fan motors, forklifts, workers 5% to 20%
- Defrost Energy added to the space by hot gas or electric defrost cycles 3% to 10%
Two of these are unique to refrigeration and neither appears in comfort load calculations. Respiration heat applies to fruits and vegetables that are still alive: apples at 32 F respire at roughly 600 to 900 Btu per ton of product per 24 hours, and the same apples at 60 F respire at four to six times that rate. Evaporator fan motor heat is not a rounding error in a low-temperature room, because the fans run continuously and every watt they draw becomes a refrigeration load.
2. Product Load: The Three-Step Calculation
Above the freezing point, the product behaves like any other mass: Q 1 = m c p , a b o v e ( T 1 − T f ) Q_1 = m \, c_{p,above} \, (T_1 - T_f) Q 1 = m c p , ab o v e ( T 1 − T f )
At the freezing point, the water in the product changes phase at constant temperature: Q 2 = m h i f Q_2 = m \, h_{if} Q 2 = m h i f
Below the freezing point, the specific heat drops by roughly half because ice has about half the specific heat of liquid water: Q 3 = m c p , b e l o w ( T f − T 2 ) Q_3 = m \, c_{p,below} \, (T_f - T_2) Q 3 = m c p , b e l o w ( T f − T 2 )
The freezing point is not 32 F. Dissolved sugars, salts, and acids depress it. Lean beef freezes near 28 F, apples near 29 F, and ice cream mix near 27 F. Using 32 F shifts energy between the sensible and latent terms and is a favorite distractor.
Representative Property Values
Product Water Content cp above freezing (Btu/lb-F) cp below freezing (Btu/lb-F) Latent heat of fusion (Btu/lb) Freezing point (F)
- Lean beef 74% 0.77 0.40 100 28
- Apples 84% 0.87 0.45 121 29
- Whole milk 88% 0.90 0.46 124 31
- Fish, fresh 76% 0.80 0.41 105 28
- Potatoes 78% 0.82 0.42 111 30
A useful sanity relationship: cp_above is approximately 0.008 times the percent water content plus 0.20 , and the latent heat of fusion is approximately 144 Btu/lb times the water fraction.
Worked Example A - Cooling Produce Without Freezing
40,000 lb of apples enter a cooler at 80 F and must be pulled down to 32 F within 24 hours. Respiration at storage temperature is 750 Btu per ton per 24 hours.
- Sensible product load: 40,000 x 0.87 x (80 - 32) = 1,670,400 Btu per 24 hours
- Respiration: (40,000 / 2,000) x 750 = 20 x 750 = 15,000 Btu per 24 hours
- Product subtotal: 1,685,400 Btu per 24 hours, or 70,225 Btu/hr, which is 5.85 tons of refrigeration
Note that no latent term appears. Apples must not freeze - the design intent is to stop exactly at 32 F, above the 29 F freezing point.
Worked Example B - Freezing Beef
20,000 lb of lean beef enters at 40 F and must reach 0 F.
- Above freezing: 20,000 x 0.77 x (40 - 28) = 184,800 Btu
- Latent: 20,000 x 100 = 2,000,000 Btu
- Below freezing: 20,000 x 0.40 x (28 - 0) = 224,000 Btu
- Total product load: 2,408,800 Btu
The latent term is 83% of the total. That single fact explains why blast freezers are enormous relative to coolers of the same volume, and why any error in the assumed freezing point barely matters compared with an error in the latent heat.
3. From Load to Equipment Capacity
Refrigeration equipment is not sized on the 24-hour average. Compressors need off-time for defrost, for pull-down recovery after door openings, and for control stability, so cold storage design uses an assumed run time of 16 to 18 hours per day : Required capacity = Total 24-hour load (Btu) design run hours \text{Required capacity} = \frac{\text{Total 24-hour load (Btu)}}{\text{design run hours}} Required capacity = design run hours Total 24-hour load (Btu)
Continuing Example B, if the freezing must be accomplished in 24 hours and the design run time is 18 hours per day, the product portion alone requires 2,408,800 / 18 = 133,800 Btu/hr, which is 11.2 tons - versus 8.4 tons if you had naively divided by 24. Add transmission, infiltration, internal gains, and defrost, and the connected capacity typically lands 40% to 70% above the raw product number.
Pull-down time is the design specification. A blast freezer that must take beef from 40 F to 0 F in 8 hours rather than 24 needs three times the capacity for the same tonnage of product. When an exam question gives you a pull-down period, that period - not 24 hours - is the denominator.
4. Evaporator TD, Humidity, and Frost
In a refrigerated room the evaporator does double duty: it holds temperature and it sets humidity. The controlling parameter is the evaporator temperature difference (TD) , the difference between room air temperature and refrigerant saturation temperature.
- Design TD Resulting Room RH Appropriate For
- 8 F to 10 F 90% to 95% Unwrapped produce, cut flowers, fresh meat in air
- 12 F to 14 F 85% to 90% Mixed storage, dairy
- 15 F to 20 F 75% to 85% Packaged and wrapped goods, freezer rooms
A small TD means a large, expensive coil operating at a warm suction temperature - which also means better compressor efficiency. Chasing a small TD is therefore not only a product-quality decision but an energy decision, and it is one of the few places in HVAC where the humidity target and the efficiency target point the same direction.
Below 32 F the coil accumulates frost rather than draining condensate. Frost insulates the surface and blocks airflow, so capacity decays between defrosts. The three common defrost methods trade first cost against parasitic load:
Air (off-cycle) defrost works only in rooms held above about 35 F, and adds no heat beyond the room air.
Electric defrost is simple and reliable, but every watt is delivered directly into the refrigerated space and must be pumped back out.
Hot gas defrost diverts discharge gas to the evaporator, is the most efficient at scale, and is standard in industrial ammonia plants.
5. Ventilation and Safety in Refrigerated Spaces
Sub-topic 2E lists "ventilation" alongside refrigeration processes for a reason. Two requirements recur:
Machinery room ventilation and refrigerant detection under ASHRAE Standard 15, developed in Section 8.3. Industrial cold storage overwhelmingly uses R-717 (ammonia), a Class B2L refrigerant whose toxicity drives the detection and emergency ventilation design.
Controlled-atmosphere storage for long-term fruit storage deliberately holds oxygen at 1% to 3% and carbon dioxide at 1% to 5% to suppress respiration. Those atmospheres are lethal, so CA rooms require entry procedures, lockable doors, and gas monitoring that a normal cooler does not.