Study guide
7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal
Key Takeaways Explain This Topic AI
Single-stage refrigeration systems suffer severe volumetric efficiency losses and extreme compressor discharge temperatures (> 275°F) when overall pressure ratios exceed r p = P cond / P evap > 8 to 10 r_p = P_{\text{cond}} / P_{\text{evap}} > 8 \text{ to } 10 r p = P cond / P evap > 8 to 10 , necessitating multi-stage compound or cascade system configurations.
Two-stage compound systems utilize low-stage (booster) and high-stage compressors operating with a single refrigerant, with optimal intermediate pressure governed by P int = P evap ⋅ P cond P_{\text{int}} = \sqrt{P_{\text{evap}} \cdot P_{\text{cond}}} P int = P evap ⋅ P cond to equalize compression ratios and minimize combined shaft work.
Direct-contact flash intercoolers perform two critical functions simultaneously: desuperheating booster discharge vapor to dry saturated vapor at P int P_{\text{int}} P int and subcooling the liquid refrigerant feed to T sat ( P int ) T_{\text{sat}}(P_{\text{int}}) T sat ( P int ) while routing flash gas directly to the high-stage compressor suction.
Cascade refrigeration systems employ two hermetically separated refrigerant circuits linked via an intermediate cascade condenser/evaporator heat exchanger, allowing the pairing of specialized high-pressure (low-temperature) and moderate-pressure (high-temperature) refrigerants.
The mass flow ratio across a cascade heat exchanger is governed by thermal equilibrium: m ˙ high / m ˙ low = ( h 2 , low − h 3 , low ) / ( h 1 , high − h 4 , high ) \dot{m}_{\text{high}} / \dot{m}_{\text{low}} = (h_{2,\text{low}} - h_{3,\text{low}}) / (h_{1,\text{high}} - h_{4,\text{high}}) m ˙ high / m ˙ low = ( h 2 , low − h 3 , low ) / ( h 1 , high − h 4 , high ) , incorporating the thermal approach difference ( Δ T cascade = T cond,low − T evap,high ≈ 5 ∘ F to 10 ∘ F \Delta T_{\text{cascade}} = T_{\text{cond,low}} - T_{\text{evap,high}} \approx 5^\circ\text{F to } 10^\circ\text{F} Δ T cascade = T cond,low − T evap,high ≈ 5 ∘ F to 1 0 ∘ F ).
Last updated: August 2026
7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal
When refrigeration applications demand large temperature lifts—such as industrial blast freezers ( − 40 ∘ F to − 60 ∘ F -40^\circ\text{F}\text{ to }-60^\circ\text{F} − 4 0 ∘ F to − 6 0 ∘ F ), pharmaceutical freeze dryers, and liquefied gas storage—a single-stage vapor-compression cycle becomes thermodynamically unfeasible. High overall pressure ratios ( r p = P cond / P evap > 8 to 10 r_p = P_{\text{cond}} / P_{\text{evap}} > 8\text{ to }10 r p = P cond / P evap > 8 to 10 ) cause extreme clearance volumetric efficiency degradation, excessive compressor discharge temperatures exceeding lubrication breakdown limits ( > 275 ∘ F > 275^\circ\text{F} > 27 5 ∘ F ), and severe COP deterioration. To overcome these constraints, mechanical engineers deploy Multi-Stage Compound Systems (single refrigerant with intercooling) and Cascade Refrigeration Systems (dual isolated refrigerant loops).
1. Single-Stage Operational Limitations & The Compression Ratio Ceiling
As the evaporator temperature drops, the evaporating saturation pressure ( P evap P_{\text{evap}} P evap ) plummets exponentially, resulting in three severe mechanical and thermodynamic penalties: +-----------------------------------------------------------------------------------------+
- | PENALTIES OF HIGH PRESSURE RATIO (r_p = P_cond / P_evap > 8 to 10) |
- +-----------------------------------------------------------------------------------------+
- | 1. Volumetric Efficiency Collapse: eta_v = 1 - c * (r_p^(1/k) - 1) --> Mass flow -> 0|
- | 2. Oil Breakdown & Valve Failure: Discharge Temp T_2 > 275°F to 325°F |
- | 3. High Throttling Irreversibility: Flash gas x_4 > 35% -> Low Net Refrigeration Effect|
- +-----------------------------------------------------------------------------------------+
To prevent equipment damage and restore thermodynamic efficiency, the total pressure lift is divided across two or more stages.
2. Multi-Stage Compound Compression Systems (Single Refrigerant)
A two-stage compound system utilizes two compressors connected in series operating on a single continuous refrigerant charge:
Low-Stage (Booster) Compressor: Draws large volumetric flow of low-density vapor from P evap P_{\text{evap}} P evap and compresses it to intermediate pressure P int P_{\text{int}} P int .
High-Stage Compressor: Draws dense vapor from P int P_{\text{int}} P int and compresses it to final condensing pressure P cond P_{\text{cond}} P cond . +-----------------------------------------------------------------------------------------+
- | TWO-STAGE COMPOUND SYSTEM WITH DIRECT-CONTACT FLASH INTERCOOLER |
- +-----------------------------------------------------------------------------------------+
- | CONDENSER (P_cond) |
- | +---------------------------------+ |
- | | Condensation to Saturated Liquid| |
- | +---------------------------------+ |
- | | State 5 (h_f at P_cond) |
- | v |
- | [ High-Stage Expansion Valve ] |
- | | |
- | v State 6 (Two-Phase at P_int) |
- | +---------------------------+ |
- | State 2 (Superheated) | FLASH INTERCOOLER / | State 3 (Saturated Vapor) |
- | from Booster Comp --->| DESUPERHEATER VESSEL |---> to High-Stage Compressor |
- | +---------------------------+ (Compresses to P_cond) |
- | | |
- | v State 7 (Saturated Liquid at P_int) |
- | [ Low-Stage Expansion Valve ] |
- | | |
- | v State 8 (Two-Phase at P_evap) |
- | +---------------------------------+ |
- | | EVAPORATOR (P_evap) | |
- | +---------------------------------+ |
- | | State 1 (Saturated Vapor at P_evap) |
- | v |
- | [ Booster (Low-Stage) Comp ] |
- | (Compresses from P_evap to P_int) |
- +-----------------------------------------------------------------------------------------+
- 1. Optimal Intermediate Pressure Formulation ( P int P_{\text{int}} P int )
For an ideal two-stage system with perfect intercooling, total compressor work is minimized when the pressure ratio of each stage is identical ( r p , 1 = r p , 2 r_{p,1} = r_{p,2} r p , 1 = r p , 2 ): P int P evap = P cond P int ⟹ P int, opt = P evap ⋅ P cond \frac{P_{\text{int}}}{P_{\text{evap}}} = \frac{P_{\text{cond}}}{P_{\text{int}}} \quad \Longrightarrow \quad \mathbf{P_{\text{int, opt}} = \sqrt{P_{\text{evap}} \cdot P_{\text{cond}}}} P evap P int = P int P cond ⟹ P int, opt = P evap ⋅ P cond
2. Direct-Contact Flash Intercooler Functions & Balances
The flash intercooler performs two essential thermodynamic functions:
Desuperheating Booster Discharge Vapor: Hot discharge vapor from the booster compressor (State 2) bubbles through the saturated liquid pool in the vessel, desuperheating to dry saturated vapor (State 3, h 3 = h g , int h_3 = h_{g,\text{int}} h 3 = h g , int ) before entering the high-stage compressor. This prevents overheating the high-stage compressor.
Liquid Subcooling & Flash Gas Removal: High-pressure liquid throttled from P cond P_{\text{cond}} P cond into the vessel separates into flash gas (which bypasses the evaporator entirely) and saturated liquid at P int P_{\text{int}} P int (State 7, h 7 = h f , int h_7 = h_{f,\text{int}} h 7 = h f , int ), which feeds the low-stage expansion valve.
Mathematical Mass Balance across Flash Intercooler
Applying mass and energy conservation to the intercooler vessel:
Inflows: Booster vapor ( m ˙ low h 2 \dot{m}_{\text{low}} h_2 m ˙ low h 2 ) + Condenser liquid ( m ˙ high h 5 \dot{m}_{\text{high}} h_5 m ˙ high h 5 )
Outflows: High-stage suction ( m ˙ high h 3 \dot{m}_{\text{high}} h_3 m ˙ high h 3 ) + Liquid to evaporator ( m ˙ low h 7 \dot{m}_{\text{low}} h_7 m ˙ low h 7 ) m ˙ low h 2 + m ˙ high h 5 = m ˙ high h 3 + m ˙ low h 7 \dot{m}_{\text{low}} h_2 + \dot{m}_{\text{high}} h_5 = \dot{m}_{\text{high}} h_3 + \dot{m}_{\text{low}} h_7 m ˙ low h 2 + m ˙ high h 5 = m ˙ high h 3 + m ˙ low h 7 m ˙ high ( h 3 − h 5 ) = m ˙ low ( h 2 − h 7 ) \dot{m}_{\text{high}} (h_3 - h_5) = \dot{m}_{\text{low}} (h_2 - h_7) m ˙ high ( h 3 − h 5 ) = m ˙ low ( h 2 − h 7 ) m ˙ high m ˙ low = h 2 − h f , int h g , int − h f , cond \mathbf{\frac{\dot{m}_{\text{high}}}{\dot{m}_{\text{low}}} = \frac{h_2 - h_{f,\text{int}}}{h_{g,\text{int}} - h_{f,\text{cond}}}} m ˙ low m ˙ high = h g , int − h f , cond h 2 − h f , int m ˙ low = Q ˙ evap h 1 − h 7 = Q ˙ evap h 1 − h f , int \dot{m}_{\text{low}} = \frac{\dot{Q}_{\text{evap}}}{h_1 - h_7} = \frac{\dot{Q}_{\text{evap}}}{h_1 - h_{f,\text{int}}} m ˙ low = h 1 − h 7 Q ˙ evap = h 1 − h f , int Q ˙ evap W ˙ total = m ˙ low ( h 2 − h 1 ) + m ˙ high ( h 4 − h 3 ) \dot{W}_{\text{total}} = \dot{m}_{\text{low}} (h_2 - h_1) + \dot{m}_{\text{high}} (h_4 - h_3) W ˙ total = m ˙ low ( h 2 − h 1 ) + m ˙ high ( h 4 − h 3 )
3. Cascade Refrigeration Systems (Two Separate Refrigerants)
When target temperatures drop below − 50 ∘ F to − 120 ∘ F -50^\circ\text{F}\text{ to }-120^\circ\text{F} − 5 0 ∘ F to − 12 0 ∘ F , a single refrigerant cannot effectively span the entire pressure range. A refrigerant that has a reasonable condensing pressure at 100 ∘ F 100^\circ\text{F} 10 0 ∘ F (e.g., R-134a) would have an evaporating pressure at − 60 ∘ F -60^\circ\text{F} − 6 0 ∘ F in deep vacuum ( < 1.5 psia < 1.5\text{ psia} < 1.5 psia ), risking air infiltration and massive cylinder sizing. Conversely, a ultra-low-temperature refrigerant (e.g., R-23 or CO 2 \text{CO}_2 CO 2 / R-744) has an excellent vapor density at − 60 ∘ F -60^\circ\text{F} − 6 0 ∘ F , but exceeds its critical pressure ( P crit = 1 , 070 psia P_{\text{crit}} = 1,070\text{ psia} P crit = 1 , 070 psia for CO 2 \text{CO}_2 CO 2 ) at ambient condensing temperatures.
The Solution: A Cascade System connects two separate, hermetically isolated refrigeration loops via an intermediate heat exchanger called the Cascade Condenser . +-----------------------------------------------------------------------------------------+
- | CASCADE REFRIGERATION SYSTEM ARCHITECTURE (DUAL REFRIGERANT) |
- +-----------------------------------------------------------------------------------------+
- | [ HIGH-TEMPERATURE STAGE: e.g., R-134a, R-404A, or R-717 (Ammonia) ] |
- | |
- | +---> [ High-Temp Compressor ] ---> [ High-Temp Condenser (Ambient Air/Water) ]-+ |
- | | | |
- | | [ High-Temp Expansion Valve ] | |
- | | | | |
- | | +=============================================+ v | |
- | +---- | CASCADE CONDENSER / EVAPORATOR HEAT EXCHANGER| <---+ | |
- | | High-Temp Evaporator <-- Absorbs Heat --+ | | |
- | | Low-Temp Condenser -- Rejects Heat --+ | | |
- | +=============================================+ | |
- | ^ | |
- | +-------------------------------------------------+ | |
- | | [ Low-Temp Expansion Valve ] | |
- | | | | |
- | +---< [ Low-Temp Compressor ] <--- [ Low-Temp Evaporator (Ultra-Cold Load) ] <--+ |
- | |
- | [ LOW-TEMPERATURE STAGE: e.g., R-23, R-744 (CO_2), R-508B ] |
- +-----------------------------------------------------------------------------------------+
- 1. Thermal Equilibrium Across the Cascade Condenser
The cascade condenser acts as the evaporator for the high-temperature circuit and the condenser for the low-temperature circuit. A finite temperature approach difference ( Δ T cascade = T cond, low − T evap, high ≈ 5 ∘ F to 10 ∘ F \Delta T_{\text{cascade}} = T_{\text{cond, low}} - T_{\text{evap, high}} \approx 5^\circ\text{F}\text{ to }10^\circ\text{F} Δ T cascade = T cond, low − T evap, high ≈ 5 ∘ F to 1 0 ∘ F ) drives heat transfer: Q ˙ cascade = m ˙ low ( h 2 , low − h 3 , low ) = m ˙ high ( h 1 , high − h 4 , high ) \dot{Q}_{\text{cascade}} = \dot{m}_{\text{low}} (h_{2,\text{low}} - h_{3,\text{low}}) = \dot{m}_{\text{high}} (h_{1,\text{high}} - h_{4,\text{high}}) Q ˙ cascade = m ˙ low ( h 2 , low − h 3 , low ) = m ˙ high ( h 1 , high − h 4 , high )
2. Cascade Mass Flow Ratio m ˙ high m ˙ low = h 2 , low − h 3 , low h 1 , high − h 4 , high = h 2 , low − h 3 , low h 1 , high − h 3 , high \mathbf{\frac{\dot{m}_{\text{high}}}{\dot{m}_{\text{low}}} = \frac{h_{2,\text{low}} - h_{3,\text{low}}}{h_{1,\text{high}} - h_{4,\text{high}}} = \frac{h_{2,\text{low}} - h_{3,\text{low}}}{h_{1,\text{high}} - h_{3,\text{high}}}} m ˙ low m ˙ high = h 1 , high − h 4 , high h 2 , low − h 3 , low = h 1 , high − h 3 , high h 2 , low − h 3 , low
3. Overall Cascade COP COP cascade = Q ˙ evap, low W ˙ comp, low + W ˙ comp, high = m ˙ low ( h 1 , low − h 4 , low ) m ˙ low ( h 2 , low − h 1 , low ) + m ˙ high ( h 2 , high − h 1 , high ) \text{COP}_{\text{cascade}} = \frac{\dot{Q}_{\text{evap, low}}}{\dot{W}_{\text{comp, low}} + \dot{W}_{\text{comp, high}}} = \frac{\dot{m}_{\text{low}} (h_{1,\text{low}} - h_{4,\text{low}})}{\dot{m}_{\text{low}} (h_{2,\text{low}} - h_{1,\text{low}}) + \dot{m}_{\text{high}} (h_{2,\text{high}} - h_{1,\text{high}})} COP cascade = W ˙ comp, low + W ˙ comp, high Q ˙ evap, low = m ˙ low ( h 2 , low − h 1 , low ) + m ˙ high ( h 2 , high − h 1 , high ) m ˙ low ( h 1 , low − h 4 , low )
4. Multi-Stage Compound vs. Cascade Systems Comparison
- Feature / Parameter Multi-Stage Compound System Cascade Refrigeration System
- Working Fluid Single refrigerant throughout entire system Two separate, chemically distinct refrigerants
Lubrication Oil Circuit Shared oil circuit; requires interstage oil separators Completely separated oil circuits matched to each refrigerant
Intermediate Heat Transfer Direct-contact flash mixing or shell-and-coil Indirect heat exchange across cascade heat exchanger
Intermediate Thermal Loss Zero temperature approach loss in direct-contact tank 5 ∘ F to 10 ∘ F 5^\circ\text{F}\text{ to }10^\circ\text{F} 5 ∘ F to 1 0 ∘ F approach Δ T \Delta T Δ T penalty across cascade condenser
Temperature Range Down to − 40 ∘ F -40^\circ\text{F} − 4 0 ∘ F (Ammonia, R-404A, R-507A) Down to − 120 ∘ F -120^\circ\text{F} − 12 0 ∘ F ( CO 2 \text{CO}_2 CO 2 /R-134a, R-23/R-404A)
Standstill Pressure Standard system pressures at room temperature Low-stage refrigerant requires expansion tank during shutdown
5. NCEES Reference Handbook Navigation Tactics
Intermediate Pressure Formula: Search "Compound Refrigeration" or "Intermediate Pressure" in Section 7 to locate P i = P e P c P_i = \sqrt{P_e P_c} P i = P e P c .
Ammonia (R-717) Property Tables: Locate Ammonia tables in Section 7 . Look for saturated vapor enthalpy h g h_g h g , saturated liquid enthalpy h f h_f h f , and superheated vapor entropy lines.
Cascade Energy Balance: Search "Cascade" to verify the mass flow ratio equation m ˙ H / m ˙ L = Δ h L / Δ h H \dot{m}_H / \dot{m}_L = \Delta h_L / \Delta h_H m ˙ H / m ˙ L = Δ h L /Δ h H .
- 6. Worked Computational Examples
- Example 1: Two-Stage Ammonia (R-717) System with Direct Flash Intercooler
An industrial cold storage plant requires 50 Tons 50\text{ Tons} 50 Tons of refrigeration at an evaporating temperature of − 30 ∘ F -30^\circ\text{F} − 3 0 ∘ F ( P evap = 13.90 psia P_{\text{evap}} = 13.90\text{ psia} P evap = 13.90 psia ) with a condensing temperature of 95 ∘ F 95^\circ\text{F} 9 5 ∘ F ( P cond = 195.8 psia P_{\text{cond}} = 195.8\text{ psia} P cond = 195.8 psia ). The plant utilizes a two-stage Ammonia (R-717) compound system with a direct-contact flash intercooler operating at optimal intermediate pressure P int = 13.90 × 195.8 = 52.17 psia P_{\text{int}} = \sqrt{13.90 \times 195.8} = 52.17\text{ psia} P int = 13.90 × 195.8 = 52.17 psia ( T sat, int = 24.0 ∘ F T_{\text{sat, int}} = 24.0^\circ\text{F} T sat, int = 24. 0 ∘ F ).
- Booster isentropic efficiency: η s , 1 = 0.80 \eta_{s,1} = 0.80 η s , 1 = 0.80
- High-stage isentropic efficiency: η s , 2 = 0.82 \eta_{s,2} = 0.82 η s , 2 = 0.82
Thermodynamic Properties (Ammonia R-717):
At − 30 ∘ F -30^\circ\text{F} − 3 0 ∘ F ( 13.90 psia 13.90\text{ psia} 13.90 psia ): h 1 = 597.6 Btu/lbm h_1 = 597.6\text{ Btu/lbm} h 1 = 597.6 Btu/lbm , s 1 = 1.417 Btu/(lbm ⋅ ∘ R) s_1 = 1.417\text{ Btu/(lbm}\cdot{}^\circ\text{R)} s 1 = 1.417 Btu/(lbm ⋅ ∘ R)
Booster isentropic compression to 52.2 psia 52.2\text{ psia} 52.2 psia : h 2 s = 672.0 Btu/lbm h_{2s} = 672.0\text{ Btu/lbm} h 2 s = 672.0 Btu/lbm
At 24 ∘ F 24^\circ\text{F} 2 4 ∘ F ( 52.2 psia 52.2\text{ psia} 52.2 psia ): h 3 = h g , int = 619.1 Btu/lbm h_3 = h_{g,\text{int}} = 619.1\text{ Btu/lbm} h 3 = h g , int = 619.1 Btu/lbm , s 3 = 1.287 Btu/(lbm ⋅ ∘ R) s_3 = 1.287\text{ Btu/(lbm}\cdot{}^\circ\text{R)} s 3 = 1.287 Btu/(lbm ⋅ ∘ R) , h 7 = h f , int = 69.3 Btu/lbm h_7 = h_{f,\text{int}} = 69.3\text{ Btu/lbm} h 7 = h f , int = 69.3 Btu/lbm
High-stage isentropic compression to 195.8 psia 195.8\text{ psia} 195.8 psia : h 4 s = 698.5 Btu/lbm h_{4s} = 698.5\text{ Btu/lbm} h 4 s = 698.5 Btu/lbm
At 95 ∘ F 95^\circ\text{F} 9 5 ∘ F ( 195.8 psia 195.8\text{ psia} 195.8 psia ): h 5 = h f , cond = 149.4 Btu/lbm h_5 = h_{f,\text{cond}} = 149.4\text{ Btu/lbm} h 5 = h f , cond = 149.4 Btu/lbm
Calculate: (a) Booster refrigerant mass flow rate ( m ˙ low \dot{m}_{\text{low}} m ˙ low ), (b) High-stage mass flow rate ( m ˙ high \dot{m}_{\text{high}} m ˙ high ), (c) Total compressor power ( kW \text{kW} kW ), and (d) Cycle COP \text{COP} COP .
Solution:
Booster Mass Flow Rate: Q ˙ evap = 50 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 600 , 000 Btu/hr \dot{Q}_{\text{evap}} = 50\text{ Tons} \times 12,000\text{ Btu/(hr}\cdot\text{Ton)} = 600,000\text{ Btu/hr} Q ˙ evap = 50 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 600 , 000 Btu/hr q evap = h 1 − h 7 = 597.6 − 69.3 = 528.3 Btu/lbm q_{\text{evap}} = h_1 - h_7 = 597.6 - 69.3 = 528.3\text{ Btu/lbm} q evap = h 1 − h 7 = 597.6 − 69.3 = 528.3 Btu/lbm m ˙ low = 600 , 000 Btu/hr 528.3 Btu/lbm = 1 , 135.72 lbm/hr \dot{m}_{\text{low}} = \frac{600,000\text{ Btu/hr}}{528.3\text{ Btu/lbm}} = \mathbf{1,135.72\text{ lbm/hr}} m ˙ low = 528.3 Btu/lbm 600 , 000 Btu/hr = 1 , 135.72 lbm/hr
Booster Actual Discharge Enthalpy ( h 2 h_2 h 2 ): h 2 = h 1 + h 2 s − h 1 η s , 1 = 597.6 + 672.0 − 597.6 0.80 = 597.6 + 74.4 0.80 = 597.6 + 93.0 = 690.6 Btu/lbm h_2 = h_1 + \frac{h_{2s} - h_1}{\eta_{s,1}} = 597.6 + \frac{672.0 - 597.6}{0.80} = 597.6 + \frac{74.4}{0.80} = 597.6 + 93.0 = \mathbf{690.6\text{ Btu/lbm}} h 2 = h 1 + η s , 1 h 2 s − h 1 = 597.6 + 0.80 672.0 − 597.6 = 597.6 + 0.80 74.4 = 597.6 + 93.0 = 690.6 Btu/lbm
High-Stage Mass Flow Rate ( m ˙ high \dot{m}_{\text{high}} m ˙ high ): m ˙ high m ˙ low = h 2 − h f , int h g , int − h f , cond = 690.6 − 69.3 619.1 − 149.4 = 621.3 469.7 = 1.3228 \frac{\dot{m}_{\text{high}}}{\dot{m}_{\text{low}}} = \frac{h_2 - h_{f,\text{int}}}{h_{g,\text{int}} - h_{f,\text{cond}}} = \frac{690.6 - 69.3}{619.1 - 149.4} = \frac{621.3}{469.7} = 1.3228 m ˙ low m ˙ high = h g , int − h f , cond h 2 − h f , int = 619.1 − 149.4 690.6 − 69.3 = 469.7 621.3 = 1.3228 m ˙ high = 1 , 135.72 lbm/hr × 1.3228 = 1 , 502.33 lbm/hr \dot{m}_{\text{high}} = 1,135.72\text{ lbm/hr} \times 1.3228 = \mathbf{1,502.33\text{ lbm/hr}} m ˙ high = 1 , 135.72 lbm/hr × 1.3228 = 1 , 502.33 lbm/hr
High-Stage Actual Discharge Enthalpy ( h 4 h_4 h 4 ): h 4 = h 3 + h 4 s − h 3 η s , 2 = 619.1 + 698.5 − 619.1 0.82 = 619.1 + 79.4 0.82 = 619.1 + 96.8 = 715.9 Btu/lbm h_4 = h_3 + \frac{h_{4s} - h_3}{\eta_{s,2}} = 619.1 + \frac{698.5 - 619.1}{0.82} = 619.1 + \frac{79.4}{0.82} = 619.1 + 96.8 = \mathbf{715.9\text{ Btu/lbm}} h 4 = h 3 + η s , 2 h 4 s − h 3 = 619.1 + 0.82 698.5 − 619.1 = 619.1 + 0.82 79.4 = 619.1 + 96.8 = 715.9 Btu/lbm
Total Compressor Power: W ˙ booster = m ˙ low ( h 2 − h 1 ) = 1 , 135.72 × ( 690.6 − 597.6 ) = 1 , 135.72 × 93.0 = 105 , 622 Btu/hr \dot{W}_{\text{booster}} = \dot{m}_{\text{low}} (h_2 - h_1) = 1,135.72 \times (690.6 - 597.6) = 1,135.72 \times 93.0 = 105,622\text{ Btu/hr} W ˙ booster = m ˙ low ( h 2 − h 1 ) = 1 , 135.72 × ( 690.6 − 597.6 ) = 1 , 135.72 × 93.0 = 105 , 622 Btu/hr W ˙ high = m ˙ high ( h 4 − h 3 ) = 1 , 502.33 × ( 715.9 − 619.1 ) = 1 , 502.33 × 96.8 = 145 , 426 Btu/hr \dot{W}_{\text{high}} = \dot{m}_{\text{high}} (h_4 - h_3) = 1,502.33 \times (715.9 - 619.1) = 1,502.33 \times 96.8 = 145,426\text{ Btu/hr} W ˙ high = m ˙ high ( h 4 − h 3 ) = 1 , 502.33 × ( 715.9 − 619.1 ) = 1 , 502.33 × 96.8 = 145 , 426 Btu/hr W ˙ total = 105 , 622 + 145 , 426 = 251 , 048 Btu/hr \dot{W}_{\text{total}} = 105,622 + 145,426 = 251,048\text{ Btu/hr} W ˙ total = 105 , 622 + 145 , 426 = 251 , 048 Btu/hr Power [kW] = 251 , 048 Btu/hr 3 , 412.14 Btu/(kW ⋅ hr) = 73.57 kW ( 1.471 kW/ton ) \text{Power [kW]} = \frac{251,048\text{ Btu/hr}}{3,412.14\text{ Btu/(kW}\cdot\text{hr)}} = \mathbf{73.57\text{ kW}} \quad (1.471\text{ kW/ton}) Power [kW] = 3 , 412.14 Btu/(kW ⋅ hr) 251 , 048 Btu/hr = 73.57 kW ( 1.471 kW/ton )
Cycle COP: COP = Q ˙ evap W ˙ total = 600 , 000 251 , 048 = 2.390 \text{COP} = \frac{\dot{Q}_{\text{evap}}}{\dot{W}_{\text{total}}} = \frac{600,000}{251,048} = \mathbf{2.390} COP = W ˙ total Q ˙ evap = 251 , 048 600 , 000 = 2.390
Example 2: Cascade System Performance ( CO 2 \text{CO}_2 CO 2 / R-134a)
A 30 -Ton 30\text{-Ton} 30 -Ton blast freezer is cooled by a cascade system comprising a low-temperature CO 2 \text{CO}_2 CO 2 (R-744) loop and a high-temperature R-134a loop.
CO 2 \text{CO}_2 CO 2 Evaporating: T evap, low = − 50 ∘ F T_{\text{evap, low}} = -50^\circ\text{F} T evap, low = − 5 0 ∘ F ( h 1 = 138.5 Btu/lbm h_1 = 138.5\text{ Btu/lbm} h 1 = 138.5 Btu/lbm , h 2 = 159.2 Btu/lbm h_2 = 159.2\text{ Btu/lbm} h 2 = 159.2 Btu/lbm , h 3 = h 4 = 31.8 Btu/lbm h_3 = h_4 = 31.8\text{ Btu/lbm} h 3 = h 4 = 31.8 Btu/lbm )
Cascade Condenser Approach: Δ T cascade = 10 ∘ F \Delta T_{\text{cascade}} = 10^\circ\text{F} Δ T cascade = 1 0 ∘ F ( CO 2 \text{CO}_2 CO 2 condenses at 10 ∘ F 10^\circ\text{F} 1 0 ∘ F , R-134a boils at 0 ∘ F 0^\circ\text{F} 0 ∘ F )
R-134a Loop: T evap, high = 0 ∘ F T_{\text{evap, high}} = 0^\circ\text{F} T evap, high = 0 ∘ F ( h 1 = 103.1 Btu/lbm h_1 = 103.1\text{ Btu/lbm} h 1 = 103.1 Btu/lbm , h 2 = 120.4 Btu/lbm h_2 = 120.4\text{ Btu/lbm} h 2 = 120.4 Btu/lbm , h 3 = h 4 = 44.4 Btu/lbm h_3 = h_4 = 44.4\text{ Btu/lbm} h 3 = h 4 = 44.4 Btu/lbm )
Calculate: (a) CO 2 \text{CO}_2 CO 2 mass flow rate, (b) Heat rejected across the cascade condenser, (c) R-134a mass flow rate, and (d) Total system COP.
Solution:
CO 2 \text{CO}_2 CO 2 Mass Flow Rate: Q ˙ evap = 30 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 360 , 000 Btu/hr \dot{Q}_{\text{evap}} = 30\text{ Tons} \times 12,000\text{ Btu/(hr}\cdot\text{Ton)} = 360,000\text{ Btu/hr} Q ˙ evap = 30 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 360 , 000 Btu/hr m ˙ low = 360 , 000 h 1 , low − h 4 , low = 360 , 000 138.5 − 31.8 = 360 , 000 106.7 = 3 , 373.95 lbm/hr \dot{m}_{\text{low}} = \frac{360,000}{h_{1,\text{low}} - h_{4,\text{low}}} = \frac{360,000}{138.5 - 31.8} = \frac{360,000}{106.7} = \mathbf{3,373.95\text{ lbm/hr}} m ˙ low = h 1 , low − h 4 , low 360 , 000 = 138.5 − 31.8 360 , 000 = 106.7 360 , 000 = 3 , 373.95 lbm/hr
Heat Rejected in Cascade Condenser: Q ˙ cascade = m ˙ low ( h 2 , low − h 3 , low ) = 3 , 373.95 × ( 159.2 − 31.8 ) = 3 , 373.95 × 127.4 = 429 , 841 Btu/hr \dot{Q}_{\text{cascade}} = \dot{m}_{\text{low}} (h_{2,\text{low}} - h_{3,\text{low}}) = 3,373.95 \times (159.2 - 31.8) = 3,373.95 \times 127.4 = \mathbf{429,841\text{ Btu/hr}} Q ˙ cascade = m ˙ low ( h 2 , low − h 3 , low ) = 3 , 373.95 × ( 159.2 − 31.8 ) = 3 , 373.95 × 127.4 = 429 , 841 Btu/hr
R-134a Mass Flow Rate: m ˙ high = Q ˙ cascade h 1 , high − h 4 , high = 429 , 841 103.1 − 44.4 = 429 , 841 58.7 = 7 , 322.67 lbm/hr \dot{m}_{\text{high}} = \frac{\dot{Q}_{\text{cascade}}}{h_{1,\text{high}} - h_{4,\text{high}}} = \frac{429,841}{103.1 - 44.4} = \frac{429,841}{58.7} = \mathbf{7,322.67\text{ lbm/hr}} m ˙ high = h 1 , high − h 4 , high Q ˙ cascade = 103.1 − 44.4 429 , 841 = 58.7 429 , 841 = 7 , 322.67 lbm/hr
Compressor Work & System COP: W ˙ low = 3 , 373.95 × ( 159.2 − 138.5 ) = 3 , 373.95 × 20.7 = 69 , 841 Btu/hr \dot{W}_{\text{low}} = 3,373.95 \times (159.2 - 138.5) = 3,373.95 \times 20.7 = 69,841\text{ Btu/hr} W ˙ low = 3 , 373.95 × ( 159.2 − 138.5 ) = 3 , 373.95 × 20.7 = 69 , 841 Btu/hr W ˙ high = 7 , 322.67 × ( 120.4 − 103.1 ) = 7 , 322.67 × 17.3 = 126 , 682 Btu/hr \dot{W}_{\text{high}} = 7,322.67 \times (120.4 - 103.1) = 7,322.67 \times 17.3 = 126,682\text{ Btu/hr} W ˙ high = 7 , 322.67 × ( 120.4 − 103.1 ) = 7 , 322.67 × 17.3 = 126 , 682 Btu/hr W ˙ total = 69 , 841 + 126 , 682 = 196 , 523 Btu/hr \dot{W}_{\text{total}} = 69,841 + 126,682 = 196,523\text{ Btu/hr} W ˙ total = 69 , 841 + 126 , 682 = 196 , 523 Btu/hr COP cascade = 360 , 000 Btu/hr 196 , 523 Btu/hr = 1.832 \text{COP}_{\text{cascade}} = \frac{360,000\text{ Btu/hr}}{196,523\text{ Btu/hr}} = \mathbf{1.832} COP cascade = 196 , 523 Btu/hr 360 , 000 Btu/hr = 1.832