Study guide

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams

Key Takeaways Explain This Topic AI

The standard vapor-compression refrigeration cycle consists of four baseline processes: isentropic/actual compression (1-2), isobaric condensation and heat rejection (2-3), isenthalpic throttling expansion (3-4), and isobaric/isothermal evaporation and heat absorption (4-1).

Refrigeration capacity is governed by mass flow rate and net evaporator enthalpy rise: Q ˙ evap = m ˙ r ( h 1 − h 4 ) = m ˙ r ( h 1 − h 3 ) \dot{Q}_{\text{evap}} = \dot{m}_r (h_1 - h_4) = \dot{m}_r (h_1 - h_3) Q ˙ ​ evap ​ = m ˙ r ​ ( h 1 ​ − h 4 ​ ) = m ˙ r ​ ( h 1 ​ − h 3 ​ ) , where 1 Ton of Refrigeration (TR) equals 12,000 Btu/hr (3.51685 kW).

Real compressor performance deviates from ideal isentropic compression due to friction, fluid turbulence, and valve losses, quantified by isentropic efficiency: η s = ( h 2 s − h 1 ) / ( h 2 − h 1 ) \eta_s = (h_{2s} - h_1) / (h_2 - h_1) η s ​ = ( h 2 s ​ − h 1 ​ ) / ( h 2 ​ − h 1 ​ ) , which elevates required shaft work and refrigerant discharge temperature.

Isenthalpic throttling (h_3 = h_4) across an expansion device (TXV, electronic expansion valve, or orifice) causes instantaneous flashing into a two-phase mixture with quality x_4 = (h_4 - h_f) / h_{fg}, generating non-refrigerating flash gas prior to the evaporator inlet.

Total condenser heat rejection equals the sum of cooling capacity and compressor power input: Q ˙ cond = Q ˙ evap + W ˙ comp \dot{Q}_{\text{cond}} = \dot{Q}_{\text{evap}} + \dot{W}_{\text{comp}} Q ˙ ​ cond ​ = Q ˙ ​ evap ​ + W ˙ comp ​ , producing a Heat Rejection Ratio ( H R R = Q ˙ cond / Q ˙ evap = 1 + 1 / COP R HRR = \dot{Q}_{\text{cond}} / \dot{Q}_{\text{evap}} = 1 + 1/\text{COP}_R H RR = Q ˙ ​ cond ​ / Q ˙ ​ evap ​ = 1 + 1/ COP R ​ ) strictly greater than 1.0.

Last updated: August 2026

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams

The vapor-compression refrigeration cycle is the foundational thermodynamic mechanism for modern air conditioning, commercial refrigeration, thermal storage, and heat pump systems. By circulating a phase-changing working fluid (refrigerant) between two distinct pressure levels, thermal energy is extracted from a low-temperature conditioned space (evaporator) and rejected to a higher-temperature ambient sink (condenser). On the PE Mechanical: HVAC and Refrigeration examination, mastery of state-point identification, enthalpy tracking across Pressure-Enthalpy ( P P P - h h h ) and Temperature-Entropy ( T T T - s s s ) diagrams, isentropic compressor efficiencies, and volumetric displacement rates is essential for solving core thermal-fluid problems.

1. Thermodynamic Architecture of the Four Core Components

A standard single-stage vapor-compression system consists of four primary components connected in a closed continuous loop: +-----------------------------------------------------------------------------------------+

  • | STANDARD SINGLE-STAGE VAPOR-COMPRESSION REFRIGERATION LOOP |
  • +-----------------------------------------------------------------------------------------+
  • | CONDENSER (High Pressure: P_cond) |
  • | +-----------------------------------------------+ |
  • | | Desuperheating -> Condensing -> Subcooling | |
  • | +-----------------------------------------------+ |
  • | ^ State 2 (Superheated Vapor) | State 3 (Saturated Liquid) |
  • | | v |
  • | +---------------+ +---------------+ |
  • | | COMPRESSOR | | EXPANSION DEV | |
  • | | (Work In: W) | | (Throttling) | |
  • | +---------------+ +---------------+ |
  • | ^ | |
  • | | State 1 (Saturated Vapor) v State 4 (Two-Phase Liquid/Vap)|
  • | +-----------------------------------------------+ |
  • | | Evaporation -> Latent Heat Absorption (Q_evap)| |
  • | +-----------------------------------------------+ |
  • | EVAPORATOR (Low Pressure: P_evap) |
  • +-----------------------------------------------------------------------------------------+
  • Detailed State-Point Sequence

State 1 → \rightarrow → State 2 (Compression Process):

Ideal (Isentropic): Reversible, adiabatic compression of saturated (or slightly superheated) vapor from low evaporating pressure ( P evap P_{\text{evap}} P evap ​ ) to high condensing pressure ( P cond P_{\text{cond}} P cond ​ ) along a line of constant entropy ( s 1 = s 2 s s_1 = s_{2s} s 1 ​ = s 2 s ​ ).

Actual (Non-Isentropic): Internal friction, valve pressure drops, and irreversible turbulence increase refrigerant entropy ( s 2 > s 1 s_2 > s_1 s 2 ​ > s 1 ​ ), resulting in a higher discharge enthalpy ( h 2 > h 2 s h_2 > h_{2s} h 2 ​ > h 2 s ​ ) and elevated discharge temperature ( T 2 > T 2 s T_2 > T_{2s} T 2 ​ > T 2 s ​ ).

Compressor Work Input: w in = h 2 − h 1 = h 2 s − h 1 η s w_{\text{in}} = h_2 - h_1 = \frac{h_{2s} - h_1}{\eta_s} w in ​ = h 2 ​ − h 1 ​ = η s ​ h 2 s ​ − h 1 ​ ​

State 2 → \rightarrow → State 3 (Isobaric Heat Rejection Process):

High-pressure superheated vapor enters the condenser, desuperheats to saturation temperature ( T cond T_{\text{cond}} T cond ​ ), undergoes isothermal latent heat condensation to saturated liquid, and leaves as saturated (or subcooled) liquid at state 3 ( h 3 = h f h_3 = h_f h 3 ​ = h f ​ at P cond P_{\text{cond}} P cond ​ ).

Condenser Heat Rejection Rate: q cond = h 2 − h 3 q_{\text{cond}} = h_2 - h_3 q cond ​ = h 2 ​ − h 3 ​

State 3 → \rightarrow → State 4 (Isenthalpic Throttling Process):

Saturated high-pressure liquid passes through an adiabatic expansion device (thermostatic expansion valve, electronic expansion valve, capillary tube, or fixed orifice). No shaft work is performed and heat transfer is negligible, rendering the process strictly isenthalpic ( h 4 = h 3 h_4 = h_3 h 4 ​ = h 3 ​ ).

The sudden pressure drop causes a portion of the liquid to boil instantly into flash gas , yielding a low-temperature two-phase mixture at state 4 with vapor quality x 4 x_4 x 4 ​ : x 4 = h 4 − h f , evap h f g , evap = h 3 − h f , evap h g , evap − h f , evap x_4 = \frac{h_4 - h_{f,\text{evap}}}{h_{fg,\text{evap}}} = \frac{h_3 - h_{f,\text{evap}}}{h_{g,\text{evap}} - h_{f,\text{evap}}} x 4 ​ = h f g , evap ​ h 4 ​ − h f , evap ​ ​ = h g , evap ​ − h f , evap ​ h 3 ​ − h f , evap ​ ​

State 4 → \rightarrow → State 1 (Isobaric/Isothermal Heat Absorption Process):

The low-pressure two-phase mixture enters the evaporator tubes, absorbing latent heat from the refrigerated space or chilled water stream at constant evaporating temperature ( T evap T_{\text{evap}} T evap ​ ) and constant pressure ( P evap P_{\text{evap}} P evap ​ ) until fully vaporized to saturated vapor at state 1 ( h 1 = h g h_1 = h_g h 1 ​ = h g ​ at P evap P_{\text{evap}} P evap ​ ).

Refrigeration Effect: q evap = h 1 − h 4 = h 1 − h 3 q_{\text{evap}} = h_1 - h_4 = h_1 - h_3 q evap ​ = h 1 ​ − h 4 ​ = h 1 ​ − h 3 ​

2. Thermodynamic Property Mapping: P-h & T-s Diagrams

Understanding the geometry of refrigerant saturation domes on P P P - h h h and T T T - s s s coordinates allows rapid verification of cycle performance and identifying irreversibilities. +-----------------------------------------------------------------------------------------+

  • | PRESSURE-ENTHALPY (P-h) DIAGRAM | TEMPERATURE-ENTROPY (T-s) DIAGRAM |
  • +-----------------------------------------------------------------------------------------+
  • | Pressure (P) | Temperature (T) |
  • | ^ Saturated Saturated | ^ Saturated Saturated |
  • | | Liquid Vapor | | Liquid Vapor |
  • | | P_cond 3_________2 2s | | P_cond .-------2 2s |
  • | | | / / | | / 3 / / |
  • | | | / / | | / | / / |
  • | | | / / | | / | / / |
  • | | P_evap 4______1_/ | | P_evap / 4--1_/ |
  • | | / \ | | / \ |
  • | +-----------------------------> | +-----------------------------> |
  • | 0 Enthalpy (h) | 0 Entropy (s) |
  • +-----------------------------------------------------------------------------------------+
  • Key Curve Features on the P-h Diagram

Constant Pressure Lines (Isobars): Horizontal straight lines spanning the entire chart.

Constant Enthalpy Lines (Isenthalps): Vertical straight lines ( h = constant h = \text{constant} h = constant ). Expansion 3-4 drops vertically downward.

Constant Temperature Lines (Isotherms): Vertical in the subcooled liquid region (left of dome), perfectly horizontal inside the two-phase dome ( P sat P_{\text{sat}} P sat ​ dictates T sat T_{\text{sat}} T sat ​ ), and steep negative downward curves in the superheated vapor region (right of dome).

Constant Entropy Lines (Isentropes): Slanted upward and to the right in the superheated vapor region. Ideal compression (1-2s) tracks directly along an isentropic contour line.

Constant Specific Volume Lines ( v v v ): Slanted lines steeper than isentropes, crossing upward into the superheat region.

Key Curve Features on the T-s Diagram

Constant Pressure Lines: Rise exponentially through the subcooled liquid region, run horizontal across the two-phase dome, and curve upward into the superheat vapor region.

Isentropic Compression (1-2s): A vertical straight line ( s 1 = s 2 s s_1 = s_{2s} s 1 ​ = s 2 s ​ ).

Throttling Irreversibility (3-4): Throttling is an irreversible process. Although h 3 = h 4 h_3 = h_4 h 3 ​ = h 4 ​ , entropy increases ( Δ s throttle = s 4 − s 3 > 0 \Delta s_{\text{throttle}} = s_4 - s_3 > 0 Δ s throttle ​ = s 4 ​ − s 3 ​ > 0 ), shifting state 4 to the right on the T T T - s s s diagram and creating a loss of available refrigeration capacity represented by the area under curve 3-4.

3. Governing Mass & Energy Balance Formulations

Quantitative analysis of the refrigeration cycle connects component enthalpies to cooling capacity, compressor horsepower, and heat rejection rates.

1. Refrigerant Mass Flow Rate ( m ˙ r \dot{m}_r m ˙ r ​ )

Given a required cooling capacity Q ˙ evap \dot{Q}_{\text{evap}} Q ˙ ​ evap ​ (in Btu/hr \text{Btu/hr} Btu/hr or kW \text{kW} kW ): m ˙ r = Q ˙ evap q evap = Q ˙ evap h 1 − h 4 = Q ˙ evap h 1 − h 3 \dot{m}_r = \frac{\dot{Q}_{\text{evap}}}{q_{\text{evap}}} = \frac{\dot{Q}_{\text{evap}}}{h_1 - h_4} = \frac{\dot{Q}_{\text{evap}}}{h_1 - h_3} m ˙ r ​ = q evap ​ Q ˙ ​ evap ​ ​ = h 1 ​ − h 4 ​ Q ˙ ​ evap ​ ​ = h 1 ​ − h 3 ​ Q ˙ ​ evap ​ ​ In IP Units: m ˙ r [ lbm hr ] = Capacity [Tons] × 12 , 000 Btu/(hr ⋅ Ton) h 1 − h 3 [Btu/lbm] \text{In IP Units: } \dot{m}_r \left[\frac{\text{lbm}}{\text{hr}}\right] = \frac{\text{Capacity [Tons]} \times 12,000\text{ Btu/(hr}\cdot\text{Ton)}}{h_1 - h_3\text{ [Btu/lbm]}} In IP Units: m ˙ r ​ [ hr lbm ​ ] = h 1 ​ − h 3 ​ [Btu/lbm] Capacity [Tons] × 12 , 000 Btu/(hr ⋅ Ton) ​

2. Compressor Power Input & Isentropic Efficiency ( η s \eta_s η s ​ )

The theoretical (isentropic) compressor power represents the minimum thermodynamic work required: W ˙ s = m ˙ r ( h 2 s − h 1 ) \dot{W}_{s} = \dot{m}_r (h_{2s} - h_1) W ˙ s ​ = m ˙ r ​ ( h 2 s ​ − h 1 ​ )

The isentropic compressor efficiency η s \eta_s η s ​ accounts for real internal losses: η s = w s w actual = h 2 s − h 1 h 2 − h 1 \eta_s = \frac{w_s}{w_{\text{actual}}} = \frac{h_{2s} - h_1}{h_2 - h_1} η s ​ = w actual ​ w s ​ ​ = h 2 ​ − h 1 ​ h 2 s ​ − h 1 ​ ​ h 2 = h 1 + h 2 s − h 1 η s h_2 = h_1 + \frac{h_{2s} - h_1}{\eta_s} h 2 ​ = h 1 ​ + η s ​ h 2 s ​ − h 1 ​ ​

Actual indicated shaft work rate: W ˙ comp = m ˙ r ( h 2 − h 1 ) = m ˙ r ( h 2 s − h 1 ) η s \dot{W}_{\text{comp}} = \dot{m}_r (h_2 - h_1) = \frac{\dot{m}_r (h_{2s} - h_1)}{\eta_s} W ˙ comp ​ = m ˙ r ​ ( h 2 ​ − h 1 ​ ) = η s ​ m ˙ r ​ ( h 2 s ​ − h 1 ​ ) ​ Electrical Power [kW] = W ˙ comp [Btu/hr] 3 , 412.14 × η motor × η mech \text{Electrical Power [kW]} = \frac{\dot{W}_{\text{comp}} \text{ [Btu/hr]}}{3,412.14 \times \eta_{\text{motor}} \times \eta_{\text{mech}}} Electrical Power [kW] = 3 , 412.14 × η motor ​ × η mech ​ W ˙ comp ​ [Btu/hr] ​

3. Condenser Heat Rejection Rate ( Q ˙ cond \dot{Q}_{\text{cond}} Q ˙ ​ cond ​ ) & Heat Rejection Ratio (HRR)

Applying the First Law of Thermodynamics to the entire refrigeration cycle: Q ˙ cond = m ˙ r ( h 2 − h 3 ) = Q ˙ evap + W ˙ comp \dot{Q}_{\text{cond}} = \dot{m}_r (h_2 - h_3) = \dot{Q}_{\text{evap}} + \dot{W}_{\text{comp}} Q ˙ ​ cond ​ = m ˙ r ​ ( h 2 ​ − h 3 ​ ) = Q ˙ ​ evap ​ + W ˙ comp ​

The Heat Rejection Ratio (HRR) is the ratio of total heat rejected at the condenser to total heat absorbed at the evaporator: HRR = Q ˙ cond Q ˙ evap = Q ˙ evap + W ˙ comp Q ˙ evap = 1 + 1 COP R \text{HRR} = \frac{\dot{Q}_{\text{cond}}}{\dot{Q}_{\text{evap}}} = \frac{\dot{Q}_{\text{evap}} + \dot{W}_{\text{comp}}}{\dot{Q}_{\text{evap}}} = 1 + \frac{1}{\text{COP}_R} HRR = Q ˙ ​ evap ​ Q ˙ ​ cond ​ ​ = Q ˙ ​ evap ​ Q ˙ ​ evap ​ + W ˙ comp ​ ​ = 1 + COP R ​ 1 ​

Application / Temperature Range Typical COP R \text{COP}_R COP R ​ Typical HRR Range ( Q ˙ cond / Q ˙ evap \dot{Q}_{\text{cond}} / \dot{Q}_{\text{evap}} Q ˙ ​ cond ​ / Q ˙ ​ evap ​ )

Comfort Air Conditioning ( 40 ∘ F 40^\circ\text{F} 4 0 ∘ F Evap / 105 ∘ F 105^\circ\text{F} 10 5 ∘ F Cond) 4.0 to 5.5 4.0\text{ to }5.5 4.0 to 5.5 1.18 to 1.25 1.18\text{ to }1.25 1.18 to 1.25

Medium-Temp Commercial ( 20 ∘ F 20^\circ\text{F} 2 0 ∘ F Evap / 110 ∘ F 110^\circ\text{F} 11 0 ∘ F Cond) 2.8 to 3.5 2.8\text{ to }3.5 2.8 to 3.5 1.28 to 1.36 1.28\text{ to }1.36 1.28 to 1.36

Low-Temp Commercial ( − 20 ∘ F -20^\circ\text{F} − 2 0 ∘ F Evap / 110 ∘ F 110^\circ\text{F} 11 0 ∘ F Cond) 1.5 to 2.2 1.5\text{ to }2.2 1.5 to 2.2 1.45 to 1.67 1.45\text{ to }1.67 1.45 to 1.67

Ultra-Low Blast Freezing ( − 40 ∘ F -40^\circ\text{F} − 4 0 ∘ F Evap / 110 ∘ F 110^\circ\text{F} 11 0 ∘ F Cond) 1.0 to 1.4 1.0\text{ to }1.4 1.0 to 1.4 1.70 to 2.00 1.70\text{ to }2.00 1.70 to 2.00

4. Compressor Volumetric Flow Rate & Volumetric Efficiency

Refrigerant vapor entering the compressor occupies a specific volume v 1 v_1 v 1 ​ (in ft 3 / lbm \text{ft}^3/\text{lbm} ft 3 / lbm or m 3 / kg \text{m}^3/\text{kg} m 3 / kg ) evaluated at suction temperature and pressure. The required actual volumetric flow rate ( V ˙ actual \dot{V}_{\text{actual}} V ˙ actual ​ ) drawn into the compressor is: V ˙ actual = m ˙ r ⋅ v 1 \dot{V}_{\text{actual}} = \dot{m}_r \cdot v_1 V ˙ actual ​ = m ˙ r ​ ⋅ v 1 ​

Volumetric Efficiency ( η v \eta_v η v ​ )

Reciprocating and positive displacement compressors do not expel 100% of the vapor on each stroke due to clearance volume ( V c V_c V c ​ ) between the piston crown and cylinder head. The clearance volumetric efficiency is mathematically expressed as: η v = 1 − c [ ( P cond P evap ) 1 / k − 1 ] = 1 − c ( r p 1 / k − 1 ) \eta_v = 1 - c \left[ \left(\frac{P_{\text{cond}}}{P_{\text{evap}}}\right)^{1/k} - 1 \right] = 1 - c \left( r_p^{1/k} - 1 \right) η v ​ = 1 − c [ ( P evap ​ P cond ​ ​ ) 1/ k − 1 ] = 1 − c ( r p 1/ k ​ − 1 )

Where:

c = Clearance factor = V clearance / V swept (typically 0.03 to 0.07 ) c = \text{Clearance factor } = V_{\text{clearance}} / V_{\text{swept}} \text{ (typically } 0.03\text{ to }0.07\text{)} c = Clearance factor = V clearance ​ / V swept ​ (typically 0.03 to 0.07 )

r p = Pressure ratio = P cond / P evap (evaluated in absolute units: psia or kPa abs) r_p = \text{Pressure ratio } = P_{\text{cond}} / P_{\text{evap}} \text{ (evaluated in absolute units: psia or kPa abs)} r p ​ = Pressure ratio = P cond ​ / P evap ​ (evaluated in absolute units: psia or kPa abs)

k = c p / c v = Isentropic exponent of the refrigerant vapor k = c_p / c_v = \text{Isentropic exponent of the refrigerant vapor} k = c p ​ / c v ​ = Isentropic exponent of the refrigerant vapor

The required compressor theoretical displacement (swept volume rate V ˙ disp \dot{V}_{\text{disp}} V ˙ disp ​ ) is: V ˙ disp = V ˙ actual η v = m ˙ r ⋅ v 1 η v \dot{V}_{\text{disp}} = \frac{\dot{V}_{\text{actual}}}{\eta_v} = \frac{\dot{m}_r \cdot v_1}{\eta_v} V ˙ disp ​ = η v ​ V ˙ actual ​ ​ = η v ​ m ˙ r ​ ⋅ v 1 ​ ​

Exam Warning on Pressure Units: Compression ratio r p = P cond / P evap r_p = P_{\text{cond}} / P_{\text{evap}} r p ​ = P cond ​ / P evap ​ MUST always be calculated using absolute pressures ( psia = psig + 14.696 \text{psia} = \text{psig} + 14.696 psia = psig + 14.696 ). Using gauge pressures in compression ratios or volumetric efficiency formulas is a frequent failure point on the PE exam.

5. NCEES Reference Handbook Navigation Tactics

Refrigerant Property Tables & P-h Diagrams: Navigate to Section 7: HVAC & Refrigeration Applications and locate tables and thermodynamic charts for R-134a , R-410A , and R-22 .

State 1 Lookup: Find the evaporating temperature row; read saturated vapor enthalpy h g h_g h g ​ and specific entropy s g s_g s g ​ .

State 2s Lookup: Move to the condensing pressure level; follow the constant entropy line ( s = s 1 s = s_1 s = s 1 ​ ) to determine isentropic discharge enthalpy h 2 s h_{2s} h 2 s ​ .

State 3 Lookup: Find the condensing temperature row; read saturated liquid enthalpy h f h_f h f ​ .

State 4 Equality: Set h 4 = h 3 h_4 = h_3 h 4 ​ = h 3 ​ .

  • 6. Worked Computational Examples
  • Example 1: Standard 25-Ton R-134a Chiller Cycle Analysis

A water-cooled liquid chiller utilizes R-134a to deliver 25 Tons 25\text{ Tons} 25 Tons of refrigeration capacity. The system operates on a standard vapor-compression cycle under the following design conditions:

Evaporating temperature: T evap = 20 ∘ F T_{\text{evap}} = 20^\circ\text{F} T evap ​ = 2 0 ∘ F ( P evap = 33.15 psia P_{\text{evap}} = 33.15\text{ psia} P evap ​ = 33.15 psia )

Condensing temperature: T cond = 110 ∘ F T_{\text{cond}} = 110^\circ\text{F} T cond ​ = 11 0 ∘ F ( P cond = 161.1 psia P_{\text{cond}} = 161.1\text{ psia} P cond ​ = 161.1 psia )

Refrigerant enters compressor as dry saturated vapor and leaves condenser as saturated liquid.

  • Compressor isentropic efficiency: η s = 0.82 \eta_s = 0.82 η s ​ = 0.82
  • Compressor clearance volumetric efficiency: η v = 0.88 \eta_v = 0.88 η v ​ = 0.88

Thermodynamic Properties from R-134a Data:

At 20 ∘ F 20^\circ\text{F} 2 0 ∘ F : h 1 = h g = 105.30 Btu/lbm h_1 = h_g = 105.30\text{ Btu/lbm} h 1 ​ = h g ​ = 105.30 Btu/lbm , s 1 = s g = 0.2244 Btu/(lbm ⋅ ∘ R) s_1 = s_g = 0.2244\text{ Btu/(lbm}\cdot{}^\circ\text{R)} s 1 ​ = s g ​ = 0.2244 Btu/(lbm ⋅ ∘ R) , v 1 = v g = 1.397 ft 3 / lbm v_1 = v_g = 1.397\text{ ft}^3/\text{lbm} v 1 ​ = v g ​ = 1.397 ft 3 / lbm

At 110 ∘ F 110^\circ\text{F} 11 0 ∘ F : h 3 = h f = 47.90 Btu/lbm h_3 = h_f = 47.90\text{ Btu/lbm} h 3 ​ = h f ​ = 47.90 Btu/lbm

At P = 161.1 psia P = 161.1\text{ psia} P = 161.1 psia and s = 0.2244 Btu/(lbm ⋅ ∘ R) s = 0.2244\text{ Btu/(lbm}\cdot{}^\circ\text{R)} s = 0.2244 Btu/(lbm ⋅ ∘ R) : h 2 s = 119.80 Btu/lbm h_{2s} = 119.80\text{ Btu/lbm} h 2 s ​ = 119.80 Btu/lbm

Calculate: (a) Refrigerant mass flow rate ( lbm/hr \text{lbm/hr} lbm/hr ), (b) Actual compressor discharge enthalpy and power input ( kW \text{kW} kW ), (c) Condenser heat rejection rate ( Btu/hr \text{Btu/hr} Btu/hr ), (d) Coefficient of Performance ( COP R \text{COP}_R COP R ​ ), and (e) Required compressor displacement ( CFM \text{CFM} CFM ).

Solution:

Refrigerant Mass Flow Rate: Q ˙ evap = 25 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 300 , 000 Btu/hr \dot{Q}_{\text{evap}} = 25\text{ Tons} \times 12,000\text{ Btu/(hr}\cdot\text{Ton)} = 300,000\text{ Btu/hr} Q ˙ ​ evap ​ = 25 Tons × 12 , 000 Btu/(hr ⋅ Ton) = 300 , 000 Btu/hr q evap = h 1 − h 3 = 105.30 − 47.90 = 57.40 Btu/lbm q_{\text{evap}} = h_1 - h_3 = 105.30 - 47.90 = 57.40\text{ Btu/lbm} q evap ​ = h 1 ​ − h 3 ​ = 105.30 − 47.90 = 57.40 Btu/lbm m ˙ r = 300 , 000 Btu/hr 57.40 Btu/lbm = 5 , 226.48 lbm/hr ( 87.11 lbm/min ) \dot{m}_r = \frac{300,000\text{ Btu/hr}}{57.40\text{ Btu/lbm}} = 5,226.48\text{ lbm/hr} \quad (87.11\text{ lbm/min}) m ˙ r ​ = 57.40 Btu/lbm 300 , 000 Btu/hr ​ = 5 , 226.48 lbm/hr ( 87.11 lbm/min )

Actual Compressor Discharge Enthalpy & Power Input: Δ h s = h 2 s − h 1 = 119.80 − 105.30 = 14.50 Btu/lbm \Delta h_s = h_{2s} - h_1 = 119.80 - 105.30 = 14.50\text{ Btu/lbm} Δ h s ​ = h 2 s ​ − h 1 ​ = 119.80 − 105.30 = 14.50 Btu/lbm Δ h actual = Δ h s η s = 14.50 0.82 = 17.68 Btu/lbm \Delta h_{\text{actual}} = \frac{\Delta h_s}{\eta_s} = \frac{14.50}{0.82} = 17.68\text{ Btu/lbm} Δ h actual ​ = η s ​ Δ h s ​ ​ = 0.82 14.50 ​ = 17.68 Btu/lbm h 2 = h 1 + Δ h actual = 105.30 + 17.68 = 122.98 Btu/lbm h_2 = h_1 + \Delta h_{\text{actual}} = 105.30 + 17.68 = 122.98\text{ Btu/lbm} h 2 ​ = h 1 ​ + Δ h actual ​ = 105.30 + 17.68 = 122.98 Btu/lbm W ˙ comp = m ˙ r × Δ h actual = 5 , 226.48 lbm/hr × 17.68 Btu/lbm = 92 , 404 Btu/hr \dot{W}_{\text{comp}} = \dot{m}_r \times \Delta h_{\text{actual}} = 5,226.48\text{ lbm/hr} \times 17.68\text{ Btu/lbm} = 92,404\text{ Btu/hr} W ˙ comp ​ = m ˙ r ​ × Δ h actual ​ = 5 , 226.48 lbm/hr × 17.68 Btu/lbm = 92 , 404 Btu/hr Power [kW] = 92 , 404 Btu/hr 3 , 412.14 Btu/(kW ⋅ hr) = 27.08 kW \text{Power [kW]} = \frac{92,404\text{ Btu/hr}}{3,412.14\text{ Btu/(kW}\cdot\text{hr)}} = 27.08\text{ kW} Power [kW] = 3 , 412.14 Btu/(kW ⋅ hr) 92 , 404 Btu/hr ​ = 27.08 kW

Condenser Heat Rejection Rate: Q ˙ cond = m ˙ r ( h 2 − h 3 ) = 5 , 226.48 × ( 122.98 − 47.90 ) = 5 , 226.48 × 75.08 = 392 , 404 Btu/hr \dot{Q}_{\text{cond}} = \dot{m}_r (h_2 - h_3) = 5,226.48 \times (122.98 - 47.90) = 5,226.48 \times 75.08 = 392,404\text{ Btu/hr} Q ˙ ​ cond ​ = m ˙ r ​ ( h 2 ​ − h 3 ​ ) = 5 , 226.48 × ( 122.98 − 47.90 ) = 5 , 226.48 × 75.08 = 392 , 404 Btu/hr Check: Q ˙ cond = Q ˙ evap + W ˙ comp = 300 , 000 + 92 , 404 = 392 , 404 Btu/hr ✓ \text{Check: } \dot{Q}_{\text{cond}} = \dot{Q}_{\text{evap}} + \dot{W}_{\text{comp}} = 300,000 + 92,404 = 392,404\text{ Btu/hr} \quad \checkmark Check: Q ˙ ​ cond ​ = Q ˙ ​ evap ​ + W ˙ comp ​ = 300 , 000 + 92 , 404 = 392 , 404 Btu/hr ✓ HRR = 392 , 404 300 , 000 = 1.308 \text{HRR} = \frac{392,404}{300,000} = 1.308 HRR = 300 , 000 392 , 404 ​ = 1.308

Coefficient of Performance: COP R = Q ˙ evap W ˙ comp = 300 , 000 92 , 404 = 3.247 \text{COP}_R = \frac{\dot{Q}_{\text{evap}}}{\dot{W}_{\text{comp}}} = \frac{300,000}{92,404} = 3.247 COP R ​ = W ˙ comp ​ Q ˙ ​ evap ​ ​ = 92 , 404 300 , 000 ​ = 3.247

Compressor Volumetric Displacement Rate: V ˙ actual = m ˙ r ⋅ v 1 = 5 , 226.48 lbm/hr × 1.397 ft 3 / lbm 60 min/hr = 121.69 CFM \dot{V}_{\text{actual}} = \dot{m}_r \cdot v_1 = \frac{5,226.48\text{ lbm/hr} \times 1.397\text{ ft}^3/\text{lbm}}{60\text{ min/hr}} = 121.69\text{ CFM} V ˙ actual ​ = m ˙ r ​ ⋅ v 1 ​ = 60 min/hr 5 , 226.48 lbm/hr × 1.397 ft 3 / lbm ​ = 121.69 CFM V ˙ disp = V ˙ actual η v = 121.69 CFM 0.88 = 138.28 CFM \dot{V}_{\text{disp}} = \frac{\dot{V}_{\text{actual}}}{\eta_v} = \frac{121.69\text{ CFM}}{0.88} = 138.28\text{ CFM} V ˙ disp ​ = η v ​ V ˙ actual ​ ​ = 0.88 121.69 CFM ​ = 138.28 CFM

Example 2: Compression Ratio & Volumetric Efficiency for R-410A Heat Pump

An R-410A commercial rooftop heat pump operates with a suction pressure of 30.3 psig 30.3\text{ psig} 30.3 psig ( P evap = 45.0 psia P_{\text{evap}} = 45.0\text{ psia} P evap ​ = 45.0 psia ) and a condensing pressure of 345.3 psig 345.3\text{ psig} 345.3 psig ( P cond = 360.0 psia P_{\text{cond}} = 360.0\text{ psia} P cond ​ = 360.0 psia ). The compressor has a clearance factor c = 0.045 c = 0.045 c = 0.045 and the refrigerant vapor has an isentropic exponent k = 1.18 k = 1.18 k = 1.18 .

Calculate: (a) The compression ratio r p r_p r p ​ , and (b) The clearance volumetric efficiency η v \eta_v η v ​ .

Solution:

Compression Ratio: r p = P cond P evap = 360.0 psia 45.0 psia = 8.00 r_p = \frac{P_{\text{cond}}}{P_{\text{evap}}} = \frac{360.0\text{ psia}}{45.0\text{ psia}} = 8.00 r p ​ = P evap ​ P cond ​ ​ = 45.0 psia 360.0 psia ​ = 8.00

Volumetric Efficiency: η v = 1 − c ( r p 1 / k − 1 ) \eta_v = 1 - c \left( r_p^{1/k} - 1 \right) η v ​ = 1 − c ( r p 1/ k ​ − 1 ) r p 1 / k = 8.00 1 / 1.18 = 8.00 0.84746 = 5.830 r_p^{1/k} = 8.00^{1 / 1.18} = 8.00^{0.84746} = 5.830 r p 1/ k ​ = 8.0 0 1/1.18 = 8.0 0 0.84746 = 5.830 η v = 1 − 0.045 × ( 5.830 − 1 ) = 1 − ( 0.045 × 4.830 ) = 1 − 0.2174 = 0.7826 ( 78.26 % \eta_v = 1 - 0.045 \times (5.830 - 1) = 1 - (0.045 \times 4.830) = 1 - 0.2174 = 0.7826 \quad (78.26\% η v ​ = 1 − 0.045 × ( 5.830 − 1 ) = 1 − ( 0.045 × 4.830 ) = 1 − 0.2174 = 0.7826 ( 78.26%

(Note: If gauge pressures were mistakenly used, r p , wrong = 345.3 / 30.3 = 11.40 r_{p,\text{wrong}} = 345.3 / 30.3 = 11.40 r p , wrong ​ = 345.3/30.3 = 11.40 , yielding an erroneous η v = 0.645 \eta_v = 0.645 η v ​ = 0.645 —a massive 18% calculation error.)