Study guide

14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A)

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A)

Key Takeaways Explain This Topic AI

NFPA 90A and IBC Chapter 7 govern passive and active fire/smoke barrier protection, mandating dynamic Fire Dampers (UL 555), Smoke Dampers (UL 555S, Leakage Class I/II), Combination Fire/Smoke Dampers, and duct smoke detectors on AHUs > 2,000 CFM and return systems > 15,000 CFM.

NFPA 92 mandates engineered stairwell pressurization systems to maintain a minimum positive pressure difference (0.05 to 0.10 in. w.g.) relative to the fire floor while strictly limiting maximum pressure to prevent exceeding the 30 lbf maximum door opening force limit.

Door opening resistance is governed by door closer force, geometry, and differential pressure: F = F_dc + (W * A * Delta_P) / [2 * (W - d)], where excessive pressure can trap fleeing occupants or prevent firefighter egress.

Atrium smoke management relies on buoyant plume dynamics (axisymmetric, spill, and window plumes) to maintain the smoke layer interface at least 6 ft above the highest walking surface, while avoiding exhaust inlet plugholing.

Last updated: August 2026

14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A)

Smoke inhalation is the primary cause of fatalities in structural building fires. Mechanical HVAC systems can inadvertently distribute toxic smoke, soot, and carbon monoxide throughout a building if not properly integrated into life safety controls. NFPA 90A ( Standard for the Installation of Air-Conditioning and Ventilating Systems ) and NFPA 92 ( Standard for Smoke Control Systems ), along with the International Building Code (IBC) and NFPA 101 ( Life Safety Code ), establish statutory requirements for fire/smoke dampers, containment barriers, and active mechanical smoke control systems.

1. Fire, Smoke & Combination Dampers (UL 555 & UL 555S)

When HVAC ductwork penetrates fire-resistance-rated walls, floors, or smoke barriers, opening protectives must prevent the spread of fire and combustion gases. +---------------------------------------------------------------------------------------------------------+

  • | LIFE SAFETY DAMPER CLASSIFICATIONS & TESTING STANDARDS |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • | DAMPER TYPE | UL TEST STANDARD | OPERATING PRINCIPLE & APPLICATION |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • | Fire Damper (FD) | UL 555 | - Closes automatically upon heat detection via thermal link |
  • | | (1.5-hr or 3-hr) | (typically fusible link rated at 165°F or 212°F). |
  • | | | - Static (fans shut down) or Dynamic (rated to close against |
  • | | | flowing air pressure, e.g., 2,000–4,000 FPM at 4" w.g.). |
  • | | | - Installed at fire-rated walls, partitions, and floors. |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • | Smoke Damper (SD) | UL 555S | - Motorized damper operated by electric/pneumatic actuator |
  • | | (Class I, II, III) | controlled by smoke detector or fire alarm panel. |
  • | | (250°F or 350°F) | - Leakage rating: Class I (<= 4 CFM/ft2 at 1" w.g.) or |
  • | | | Class II (<= 10 CFM/ft2 at 1" w.g.). Elevated temp rated. |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • | Combination Fire/ | UL 555 & | - Combines heat-actuated fire closure (controlled high-temp |
  • | Smoke Damper (FSD) | UL 555S | bimetallic sensor) with motorized smoke control actuation. |
  • | | | - Installed where barriers have both fire & smoke ratings. |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • | Ceiling Radiation | UL 555C | - Installed at supply/return duct penetrations through fire- |
  • | Damper (CRD) | | rated floor-ceiling or roof-ceiling assemblies. |
  • +--------------------+---------------------+--------------------------------------------------------------+
  • NFPA 90A Duct Smoke Detector Mandates

Under NFPA 90A Section 6.4.2, automated duct smoke detectors must be installed in air-handling systems to initiate fan shutdown or switch systems to smoke control mode:

Supply Air Duct Detectors: Required on all supply air systems with design airflow capacity exceeding 2 , 000 CFM 2,000\ \text{CFM} 2 , 000 CFM , installed downstream of all filters and fans prior to any duct branch takeoff.

Return Air Duct Detectors: Required on all return air systems with design airflow exceeding 15 , 000 CFM 15,000\ \text{CFM} 15 , 000 CFM and serving more than one story, installed at each story return intake or at the common mixed-air connection before entering the AHU.

2. Stairwell Pressurization Systems (NFPA 92)

High-rise building stairwells serve as primary vertical egress routes for building occupants and staging platforms for fire suppression personnel. A Stairwell Pressurization System (SPS) utilizes dedicated supply fans to maintain the stair enclosure at a higher pressure than the adjacent building core, preventing smoke intrusion through doorway cracks and open doors. +---------------------------------------------------------------------------------------------------------+

  • | STAIRWELL PRESSURIZATION DYNAMICS & DESIGN BOUNDARIES |
  • +---------------------------------------------------------------------------------------------------------+
  • | |
  • | [ UPPER LIMIT: Maximum Allowable Pressure ] |
  • | Delta_P_max governed by Maximum Allowable Door Opening Force (F_door <= 30 lbf per IBC / NFPA 101) |
  • | Typically: Delta_P_max <= 0.35 to 0.45 in. w.g. |
  • | |
  • | ---------------------------------- OPERATING WINDOW ----------------------------------------------- |
  • | |
  • | [ LOWER LIMIT: Minimum Required Pressure Difference ] |
  • | Delta_P_min >= 0.05 in. w.g. (12.5 Pa) for fully sprinklered buildings |
  • | Delta_P_min >= 0.10 in. w.g. (25.0 Pa) for non-sprinklered buildings |
  • | (With design number of doors open: NFPA 92 requires min. 0.05" w.g. across closed doors) |
  • | |
  • +---------------------------------------------------------------------------------------------------------+
  • Door Opening Force Mathematical Formulation

The force required to unlatch and open a swinging egress door against a stairwell-to-space pressure difference is given by: F = F dc + W ⋅ A ⋅ Δ P 2 ( W − d ) F = F_{\text{dc}} + \frac{W \cdot A \cdot \Delta P}{2(W - d)} F = F dc ​ + 2 ( W − d ) W ⋅ A ⋅ Δ P ​

Where:

F = Total opening force exerted at door handle (lbf, statutory limit ≤ 30 lbf) F = \text{Total opening force exerted at door handle (lbf, statutory limit } \le 30\ \text{lbf)} F = Total opening force exerted at door handle (lbf, statutory limit ≤ 30 lbf)

F dc = Mechanical door closer force (lbf, typically 8 to 14 lbf) F_{\text{dc}} = \text{Mechanical door closer force (lbf, typically } 8\text{ to } 14\ \text{lbf)} F dc ​ = Mechanical door closer force (lbf, typically 8 to 14 lbf)

W = Door width (feet) W = \text{Door width (feet)} W = Door width (feet)

A = W × H = Door face area ( ft 2 ) A = W \times H = \text{Door face area } (\text{ft}^2) A = W × H = Door face area ( ft 2 )

d = Distance from center of door handle to latch edge (feet, typically 0.25 ft = 3 in.) d = \text{Distance from center of door handle to latch edge (feet, typically } 0.25\ \text{ft} = 3\ \text{in.)} d = Distance from center of door handle to latch edge (feet, typically 0.25 ft = 3 in.)

Δ P = Pressure difference across door (converted from in. w.g. to lbf/ft 2 via 1 in. w.g. = 5.204 lbf/ft 2 ) \Delta P = \text{Pressure difference across door (converted from in. w.g. to } \text{lbf/ft}^2\text{ via } 1\ \text{in. w.g.} = 5.204\ \text{lbf/ft}^2\text{)} Δ P = Pressure difference across door (converted from in. w.g. to lbf/ft 2 via 1 in. w.g. = 5.204 lbf/ft 2 ) Δ P psf = 5.204 ⋅ Δ P in. w.g. \Delta P_{\text{psf}} = 5.204 \cdot \Delta P_{\text{in. w.g.}} Δ P psf ​ = 5.204 ⋅ Δ P in. w.g. ​

Maximum Allowable Pressure Difference ( Δ P max ⁡ \Delta P_{\max} Δ P m a x ​ )

Rearranging the door force equation to solve for the maximum allowable differential pressure before doors jam shut: Δ P max ⁡ = 2 ( W − d ) ( F max ⁡ − F dc ) 5.204 ⋅ W ⋅ A ( in. w.g. ) \Delta P_{\max} = \frac{2(W - d)(F_{\max} - F_{\text{dc}})}{5.204 \cdot W \cdot A} \quad (\text{in. w.g.}) Δ P m a x ​ = 5.204 ⋅ W ⋅ A 2 ( W − d ) ( F m a x ​ − F dc ​ ) ​ ( in. w.g. )

3. Stairwell Airflow Sizing & Leakage Paths

Total stairwell pressurization supply airflow ( Q total Q_{\text{total}} Q total ​ ) must account for two simultaneous components:

Leakage through closed doors and wall/envelope cracks when all doors are shut ( Q leak Q_{\text{leak}} Q leak ​ ).

Airflow escaping through the design number of simultaneously open egress doors ( Q doors Q_{\text{doors}} Q doors ​ ) to maintain outward air velocity preventing smoke backflow. Q total = Q doors + Q leak Q_{\text{total}} = Q_{\text{doors}} + Q_{\text{leak}} Q total ​ = Q doors ​ + Q leak ​

Orifice Flow Equation for Air Leakage & Door Flow Q = 2 , 610 ⋅ A e ⋅ Δ P Q = 2,610 \cdot A_e \cdot \sqrt{\Delta P} Q = 2 , 610 ⋅ A e ​ ⋅ Δ P ​

Where:

Q = Airflow rate (CFM) Q = \text{Airflow rate (CFM)} Q = Airflow rate (CFM)

A e = Effective leakage or opening area ( ft 2 ) A_e = \text{Effective leakage or opening area } (\text{ft}^2) A e ​ = Effective leakage or opening area ( ft 2 )

Δ P = Pressure difference across barrier (in. w.g.) \Delta P = \text{Pressure difference across barrier (in. w.g.)} Δ P = Pressure difference across barrier (in. w.g.)

2 , 610 = Orifice coefficient for standard air density ( ρ = 0.075 lbm/ft 3 , C d ≈ 0.65 ) 2,610 = \text{Orifice coefficient for standard air density } (\rho = 0.075\ \text{lbm/ft}^3, C_d \approx 0.65) 2 , 610 = Orifice coefficient for standard air density ( ρ = 0.075 lbm/ft 3 , C d ​ ≈ 0.65 )

Airflow Through Open Egress Doors

NFPA 92 requires designing for a designated number of open doors (typically N = 1 N = 1 N = 1 to 3 3 3 open doors depending on building height and occupancy). The average egress door velocity requirement is typically v door ≥ 200 FPM v_{\text{door}} \ge 200\ \text{FPM} v door ​ ≥ 200 FPM to 300 FPM 300\ \text{FPM} 300 FPM across the full doorway opening: Q doors = N open ⋅ A door ⋅ v door Q_{\text{doors}} = N_{\text{open}} \cdot A_{\text{door}} \cdot v_{\text{door}} Q doors ​ = N open ​ ⋅ A door ​ ⋅ v door ​ +---------------------------------------------------------------------------------------------------------+

  • | TYPICAL EFFECTIVE LEAKAGE AREAS (A_e) IN STAIRWELL ENCLOSURES |
  • +------------------------------------+--------------------------------------------------------------------+
  • | COMPONENT | EFFECTIVE LEAKAGE AREA (A_e) |
  • +------------------------------------+--------------------------------------------------------------------+
  • | Standard Single Closed Door | 0.25 to 0.35 ft2 (un-gasketed); 0.05 to 0.10 ft2 (gasketed) |
  • | Standard Double Closed Door | 0.50 to 0.70 ft2 |
  • | Stairwell Exterior Wall (Tight) | 0.00005 ft2 per ft2 wall area |
  • | Stairwell Exterior Wall (Loose) | 0.00035 ft2 per ft2 wall area |
  • +------------------------------------+--------------------------------------------------------------------+
  • Single vs. Multiple Injection Fans

Single-Point Injection: Acceptable for low-rise stairwells ( ≤ 100 ft \le 100\ \text{ft} ≤ 100 ft / ≤ 8 \le 8 ≤ 8 stories).

Multiple-Point Injection: Required for high-rise buildings ( > 100 ft > 100\ \text{ft} > 100 ft ) to prevent severe pressure gradients where the top of the stairwell becomes over-pressurized while the bottom drops below minimum due to buoyancy/stack effect and door cycling. Injection points are typically spaced every 3 3 3 to 5 5 5 floors.

  • 4. Zoned Smoke Control & Atrium Exhaust Dynamics
  • Zoned Smoke Control

In multi-story buildings, zoned smoke control actively manipulates supply and exhaust fans to isolate the fire zone:

Fire Zone: Exhausted at high capacity ( 100 % 100\% 100% exhaust, 0 % 0\% 0% supply) to create negative relative pressure.

Adjacent Zones (Above, Below, Surrounding): Pressurized with 100 % 100\% 100% outdoor air ( 0 % 0\% 0% exhaust) to maintain positive pressure barriers ( ≥ 0.05 in. w.g. \ge 0.05\ \text{in. w.g.} ≥ 0.05 in. w.g. ), preventing smoke propagation across floor slabs.

Atrium Smoke Management (NFPA 92 Plume Equations)

In large open atriums and malls, smoke must be extracted from the ceiling plume to keep the smoke layer interface at least 6 feet 6\ \text{feet} 6 feet ( 1.83 m 1.83\ \text{m} 1.83 m ) above the highest occupied walking surface. +---------------------------------------------------------------------------------------------------------+

  • | ATRIUM SMOKE MANAGEMENT & BUOYANT PLUME MASS FLOW |
  • +---------------------------------------------------------------------------------------------------------+
  • | |
  • | Axisymmetric Plume Mass Flow Rate (m_p, in lbm/s): |
  • | |
  • | When z > z_l (Above Flame Tip): |
  • | m_p = 0.022 * Q_c^(1/3) * z^(5/3) + 0.0042 * Q_c [IP Units: Q_c in Btu/s, z in ft] |
  • | |
  • | Where: |
  • | Q_c = Convective heat release rate = 0.70 * Q_total (Btu/s) |
  • | z = Clear height from base of fire to bottom of smoke layer (ft) |
  • | z_l = Mean flame height = 0.533 * Q_c^(2/5) (ft) |
  • | |
  • | Volumetric Exhaust Flow Rate (V_exh, in CFM): |
  • | V_exh = (m_p / rho_smoke) * 60 |
  • | |
  • +---------------------------------------------------------------------------------------------------------+
  • Plugholing Prevention

If an exhaust grille extracts smoke too aggressively, ambient clear air from below the smoke layer can be pulled directly into the exhaust intake—a phenomenon known as plugholing . NFPA 92 limits the maximum volumetric flow rate ( V max ⁡ V_{\max} V m a x ​ ) per exhaust point based on smoke layer depth ( d d d ), smoke temperature ( T s T_s T s ​ ), and ambient temperature ( T o T_o T o ​ ).

  • 5. Worked Engineering Calculation: High-Rise Stairwell Pressurization Design
  • Problem Statement

A 10-story high-rise building requires a stairwell pressurization system. Egress doors are 3.0 ft 3.0\ \text{ft} 3.0 ft wide by 7.0 ft 7.0\ \text{ft} 7.0 ft high ( A = 21.0 ft 2 A = 21.0\ \text{ft}^2 A = 21.0 ft 2 ). The distance from the door handle to the unlatched edge is d = 3 inches = 0.25 ft d = 3\ \text{inches} = 0.25\ \text{ft} d = 3 inches = 0.25 ft . The door closer exerts a mechanical closing force of F dc = 12 lbf F_{\text{dc}} = 12\ \text{lbf} F dc ​ = 12 lbf .

Design criteria:

Maximum allowable door opening force: F max ⁡ = 30 lbf F_{\max} = 30\ \text{lbf} F m a x ​ = 30 lbf (IBC limit).

Minimum design pressure difference across closed doors: Δ P min ⁡ = 0.10 in. w.g. \Delta P_{\min} = 0.10\ \text{in. w.g.} Δ P m i n ​ = 0.10 in. w.g.

Number of closed doors: 8 8 8 doors, each with effective leakage area A leak = 0.25 ft 2 A_{\text{leak}} = 0.25\ \text{ft}^2 A leak ​ = 0.25 ft 2 .

System must maintain design conditions with N open = 2 N_{\text{open}} = 2 N open ​ = 2 doors fully open, requiring an average exit face velocity of v door = 250 FPM v_{\text{door}} = 250\ \text{FPM} v door ​ = 250 FPM through each open door.

Calculate:

The maximum allowable stairwell pressure difference ( Δ P max ⁡ \Delta P_{\max} Δ P m a x ​ ) before exceeding the 30 lbf 30\ \text{lbf} 30 lbf door opening force limit.

The leakage airflow through the 8 closed doors ( Q leak Q_{\text{leak}} Q leak ​ ) at Δ P = 0.10 in. w.g. \Delta P = 0.10\ \text{in. w.g.} Δ P = 0.10 in. w.g.

The airflow required through the 2 open doors ( Q doors Q_{\text{doors}} Q doors ​ ).

The total required fan supply capacity ( Q total Q_{\text{total}} Q total ​ ) including a 15 % 15\% 15% safety leakage margin.

  • Step-by-Step Solution
  • Step 1: Maximum Allowable Pressure Difference ( Δ P max ⁡ \Delta P_{\max} Δ P m a x ​ )

Available force from differential pressure: Δ F = F max ⁡ − F dc = 30 lbf − 12 lbf = 18 lbf \Delta F = F_{\max} - F_{\text{dc}} = 30\ \text{lbf} - 12\ \text{lbf} = 18\ \text{lbf} Δ F = F m a x ​ − F dc ​ = 30 lbf − 12 lbf = 18 lbf

Rearranging door force equation: Δ P psf = 2 ( W − d ) ⋅ Δ F W ⋅ A = 2 ( 3.0 − 0.25 ) × 18 3.0 × 21.0 = 2 ( 2.75 ) × 18 63.0 = 99.0 63.0 = 1.5714 lbf/ft 2 \Delta P_{\text{psf}} = \frac{2(W - d) \cdot \Delta F}{W \cdot A} = \frac{2(3.0 - 0.25) \times 18}{3.0 \times 21.0} = \frac{2(2.75) \times 18}{63.0} = \frac{99.0}{63.0} = 1.5714\ \text{lbf/ft}^2 Δ P psf ​ = W ⋅ A 2 ( W − d ) ⋅ Δ F ​ = 3.0 × 21.0 2 ( 3.0 − 0.25 ) × 18 ​ = 63.0 2 ( 2.75 ) × 18 ​ = 63.0 99.0 ​ = 1.5714 lbf/ft 2

Convert to inches water gauge: Δ P max ⁡ = Δ P psf 5.204 = 1.5714 5.204 = 0.302 in. w.g. \Delta P_{\max} = \frac{\Delta P_{\text{psf}}}{5.204} = \frac{1.5714}{5.204} = \mathbf{0.302\ \text{in. w.g.}} Δ P m a x ​ = 5.204 Δ P psf ​ ​ = 5.204 1.5714 ​ = 0.302 in. w.g. (Operating pressure window: 0.10 in. w.g. ≤ Δ P ≤ 0.30 in. w.g. 0.10\ \text{in. w.g.} \le \Delta P \le 0.30\ \text{in. w.g.} 0.10 in. w.g. ≤ Δ P ≤ 0.30 in. w.g. )

Step 2: Leakage Airflow Through Closed Doors ( Q leak Q_{\text{leak}} Q leak ​ )

Total effective leakage area for 8 closed doors: A e , total = 8 × 0.25 ft 2 = 2.0 ft 2 A_{e,\text{total}} = 8 \times 0.25\ \text{ft}^2 = 2.0\ \text{ft}^2 A e , total ​ = 8 × 0.25 ft 2 = 2.0 ft 2

Orifice leakage flow at Δ P = 0.10 in. w.g. \Delta P = 0.10\ \text{in. w.g.} Δ P = 0.10 in. w.g. Q leak = 2 , 610 × A e × Δ P = 2 , 610 × 2.0 × 0.10 = 5 , 220 × 0.31623 = 1 , 650.7 CFM Q_{\text{leak}} = 2,610 \times A_e \times \sqrt{\Delta P} = 2,610 \times 2.0 \times \sqrt{0.10} = 5,220 \times 0.31623 = \mathbf{1,650.7\ \text{CFM}} Q leak ​ = 2 , 610 × A e ​ × Δ P ​ = 2 , 610 × 2.0 × 0.10 ​ = 5 , 220 × 0.31623 = 1 , 650.7 CFM

Step 3: Airflow Through Open Egress Doors ( Q doors Q_{\text{doors}} Q doors ​ )

Total open area for 2 doors: A open = 2 × 21.0 ft 2 = 42.0 ft 2 A_{\text{open}} = 2 \times 21.0\ \text{ft}^2 = 42.0\ \text{ft}^2 A open ​ = 2 × 21.0 ft 2 = 42.0 ft 2

Airflow escaping open doors at 250 FPM 250\ \text{FPM} 250 FPM : Q doors = 42.0 ft 2 × 250 FPM = 10 , 500 CFM Q_{\text{doors}} = 42.0\ \text{ft}^2 \times 250\ \text{FPM} = \mathbf{10,500\ \text{CFM}} Q doors ​ = 42.0 ft 2 × 250 FPM = 10 , 500 CFM

Step 4: Total Required Fan Airflow Capacity ( Q total Q_{\text{total}} Q total ​ )

Base fan airflow: Q base = Q doors + Q leak = 10 , 500 + 1 , 650.7 = 12 , 150.7 CFM Q_{\text{base}} = Q_{\text{doors}} + Q_{\text{leak}} = 10,500 + 1,650.7 = 12,150.7\ \text{CFM} Q base ​ = Q doors ​ + Q leak ​ = 10 , 500 + 1 , 650.7 = 12 , 150.7 CFM

With 15 % 15\% 15% safety factor: Q total = 1.15 × 12 , 150.7 CFM = 13 , 973 CFM ≈ 14 , 000 CFM Q_{\text{total}} = 1.15 \times 12,150.7\ \text{CFM} = \mathbf{13,973\ \text{CFM}} \approx \mathbf{14,000\ \text{CFM}} Q total ​ = 1.15 × 12 , 150.7 CFM = 13 , 973 CFM ≈ 14 , 000 CFM

6. NCEES Reference Handbook Navigation Strategies

Door Opening Force: Look under HVAC — Smoke Control / Life Safety for F = F dc + W ⋅ A ⋅ Δ P 2 ( W − d ) F = F_{\text{dc}} + \frac{W \cdot A \cdot \Delta P}{2(W - d)} F = F dc ​ + 2 ( W − d ) W ⋅ A ⋅ Δ P ​ and conversion 1 in. w.g. = 5.204 lbf/ft 2 1\ \text{in. w.g.} = 5.204\ \text{lbf/ft}^2 1 in. w.g. = 5.204 lbf/ft 2 .

Orifice Flow: Search "2610" or "Orifice Flow" for Q = 2610 A e Δ P Q = 2610 A_e \sqrt{\Delta P} Q = 2610 A e ​ Δ P ​ .

Duct Detector Thresholds: Search "NFPA 90A" or "2,000 CFM" for supply air and "15,000 CFM" for return air detector mandates.