Study guide

2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling

Key Takeaways Explain This Topic AI

In the two-phase vapor dome, thermodynamic state is defined by pressure (or saturation temperature) and vapor quality x = m g m f + m g x = \frac{m_g}{m_f + m_g} x = m f ​ + m g ​ m g ​ ​ ; any property y y y is computed as y = y f + x y f g y = y_f + x y_{fg} y = y f ​ + x y f g ​ .

Superheat is the sensible temperature difference above the boiling point at a given pressure ( Δ T s h = T a c t u a l − T s a t ( P ) \Delta T_{sh} = T_{actual} - T_{sat}(P) Δ T s h ​ = T a c t u a l ​ − T s a t ​ ( P ) ); subcooling is the sensible temperature reduction below the boiling point ( Δ T s c = T s a t ( P ) − T a c t u a l \Delta T_{sc} = T_{sat}(P) - T_{actual} Δ T sc ​ = T s a t ​ ( P ) − T a c t u a l ​ ).

Liquid water and refrigerants in the compressed liquid region can be approximated using saturated liquid properties at the local fluid temperature: h ( T , P ) ≈ h f ( T ) + v f ( T ) [ P − P s a t ( T ) ] ≈ h f ( T ) h(T, P) \approx h_f(T) + v_f(T)[P - P_{sat}(T)] \approx h_f(T) h ( T , P ) ≈ h f ​ ( T ) + v f ​ ( T ) [ P − P s a t ​ ( T )] ≈ h f ​ ( T ) .

The ideal gas law P v = R T P v = R T P v = RT applies accurately to gases well above their critical temperature or at very low pressures ( P r = P / P c ≪ 1 P_r = P/P_c \ll 1 P r ​ = P / P c ​ ≪ 1 ); enthalpy changes for ideal gases depend strictly on temperature: Δ h = c p Δ T \Delta h = c_p \Delta T Δ h = c p ​ Δ T .

Real gas deviations are quantified by the compressibility factor Z = P v R T Z = \frac{P v}{R T} Z = RT P v ​ ; when Z ≠ 1.0 Z \ne 1.0 Z  = 1.0 , generalized compressibility charts based on reduced coordinates ( P r , T r P_r, T_r P r ​ , T r ​ ) must be used.

Last updated: August 2026

2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling

Accurate evaluation of thermodynamic fluid properties is fundamental to sizing HVAC equipment, steam distribution networks, and refrigeration circuits. Whether determining the enthalpy drop across a steam turbine, the required subcooling before a thermostatic expansion valve, or the density of moist air at high elevation, mechanical engineers must navigate saturated, superheated, subcooled, and ideal/real gas states with complete precision.

1. Pure Substance Phase Change & Property Diagrams

A pure substance has a fixed, homogeneous chemical composition throughout (e.g., water, nitrogen, pure refrigerants). Phase equilibrium is represented on thermodynamic coordinate diagrams including P − v P-v P − v , T − v T-v T − v , T − s T-s T − s , and P − h P-h P − h (pressure-enthalpy) diagrams. Pressure (P) ^ Critical Point (CP)

| .---.

  • | Subcooled / \ Superheated
  • | Liquid / \ Vapor
  • | Region / Two- \ Region
  • | / Phase \
  • | Saturated/ Vapor \Saturated
  • | Liquid/ Dome \Vapor
  • | Line/ \Line
  • +----------+------------------+--------> Enthalpy (h)
  • The Thermodynamic Phase Regions

Subcooled (Compressed) Liquid: Liquid whose temperature is below the saturation temperature at the given pressure ( T < T s a t ( P ) T < T_{sat}(P) T < T s a t ​ ( P ) ), or whose pressure is above the saturation pressure at the given temperature ( P > P s a t ( T ) P > P_{sat}(T) P > P s a t ​ ( T ) ).

Saturated Liquid ( f f f ): Liquid on the verge of vaporizing ( x = 0.0 x = 0.0 x = 0.0 ). Any heat addition initiates phase change at constant temperature and pressure.

Saturated Liquid-Vapor Mixture (Two-Phase Region): Coexisting liquid and vapor phases in thermodynamic equilibrium ( 0 < x < 1.0 0 < x < 1.0 0 < x < 1.0 ). Temperature and pressure are mutually dependent ( P = P s a t ( T ) P = P_{sat}(T) P = P s a t ​ ( T ) ).

Saturated Vapor ( g g g ): Vapor on the verge of condensing ( x = 1.0 x = 1.0 x = 1.0 ). Any heat removal initiates condensation at constant temperature and pressure.

Superheated Vapor: Vapor whose temperature is above the saturation temperature at the given pressure ( T > T s a t ( P ) T > T_{sat}(P) T > T s a t ​ ( P ) ), or whose pressure is below the saturation pressure at the given temperature ( P < P s a t ( T ) P < P_{sat}(T) P < P s a t ​ ( T ) ).

Supercritical Fluid: State at pressures and temperatures exceeding the Critical Point ( P > P c , T > T c P > P_c, T > T_c P > P c ​ , T > T c ​ ), where liquid and vapor phases merge into a single homogeneous fluid with no distinct phase transition boundary.

2. Vapor Quality & Two-Phase Property Evaluation

Inside the saturation dome, temperature and pressure are not independent properties. Specifying pressure automatically fixes saturation temperature ( T s a t T_{sat} T s a t ​ ), and vice versa. An additional intensive property—such as vapor quality ( x x x ) —is required to fix the state.

Vapor Quality ( x x x ) x = m g m t o t a l = m g m f + m g ( 0 ≤ x ≤ 1.0 ) x = \frac{m_g}{m_{total}} = \frac{m_g}{m_f + m_g} \quad (0 \le x \le 1.0) x = m t o t a l ​ m g ​ ​ = m f ​ + m g ​ m g ​ ​ ( 0 ≤ x ≤ 1.0 )

Where:

m g = mass of saturated vapor ( lb m or kg ) m_g = \text{mass of saturated vapor } (\text{lb}_m \text{ or kg}) m g ​ = mass of saturated vapor ( lb m ​ or kg )

m f = mass of saturated liquid ( lb m or kg ) m_f = \text{mass of saturated liquid } (\text{lb}_m \text{ or kg}) m f ​ = mass of saturated liquid ( lb m ​ or kg )

  • For saturated liquid: x = 0.0 x = 0.0 x = 0.0
  • For saturated vapor: x = 1.0 x = 1.0 x = 1.0

Quality is undefined in the single-phase compressed liquid and superheated vapor regions.

Two-Phase Mixture Property Formula

Any specific property y y y ( v , u , h , s v, u, h, s v , u , h , s ) of a saturated two-phase mixture is computed from saturated liquid ( y f y_f y f ​ ) and saturated vapor ( y g y_g y g ​ ) values: y = ( 1 − x ) y f + x y g = y f + x ( y g − y f ) = y f + x y f g y = (1 - x) y_f + x y_g = y_f + x (y_g - y_f) = y_f + x y_{fg} y = ( 1 − x ) y f ​ + x y g ​ = y f ​ + x ( y g ​ − y f ​ ) = y f ​ + x y f g ​ Specific Volume: v = v f + x v f g = v f + x ( v g − v f ) \text{Specific Volume: } v = v_f + x v_{fg} = v_f + x (v_g - v_f) Specific Volume: v = v f ​ + x v f g ​ = v f ​ + x ( v g ​ − v f ​ ) Specific Enthalpy: h = h f + x h f g = h f + x ( h g − h f ) \text{Specific Enthalpy: } h = h_f + x h_{fg} = h_f + x (h_g - h_f) Specific Enthalpy: h = h f ​ + x h f g ​ = h f ​ + x ( h g ​ − h f ​ ) Specific Entropy: s = s f + x s f g = s f + x ( s g − s f ) \text{Specific Entropy: } s = s_f + x s_{fg} = s_f + x (s_g - s_f) Specific Entropy: s = s f ​ + x s f g ​ = s f ​ + x ( s g ​ − s f ​ ) Specific Internal Energy: u = u f + x u f g = u f + x ( u g − u f ) \text{Specific Internal Energy: } u = u_f + x u_{fg} = u_f + x (u_g - u_f) Specific Internal Energy: u = u f ​ + x u f g ​ = u f ​ + x ( u g ​ − u f ​ )

To determine quality from a known mixture enthalpy h h h : x = h − h f h f g = h − h f h g − h f x = \frac{h - h_f}{h_{fg}} = \frac{h - h_f}{h_g - h_f} x = h f g ​ h − h f ​ ​ = h g ​ − h f ​ h − h f ​ ​

3. Superheat & Subcooling in HVAC/R Systems

In single-phase regions, temperature and pressure are independent properties. The degree of departure from the saturation boundary is quantified by superheat and subcooling : +-----------------------------------------------------------------------------------------+

  • | SUPERHEAT AND SUBCOOLING DEFINITIONS |
  • +-----------------------------------------------------------------------------------------+
  • | Superheat: Delta_T_sh = T_actual - T_sat(P) [Evaluated in Superheated Vapor Region]|
  • | Subcooling: Delta_T_sc = T_sat(P) - T_actual [Evaluated in Compressed Liquid Region]|
  • +-----------------------------------------------------------------------------------------+
  • Superheat ( Δ T s h \Delta T_{sh} Δ T s h ​ )

Definition: The temperature difference between the actual vapor temperature and the saturation (boiling) temperature at the local pressure: Δ T s h = T a c t u a l − T s a t ( P ) \Delta T_{sh} = T_{actual} - T_{sat}(P) Δ T s h ​ = T a c t u a l ​ − T s a t ​ ( P )

HVAC/R Importance: Evaporator superheat ( 8 ∘ F − 15 ∘ F 8^\circ\text{F} - 15^\circ\text{F} 8 ∘ F − 1 5 ∘ F ) ensures that 100% dry vapor enters the compressor suction port, preventing catastrophic liquid droplet slugging and oil dilution.

Subcooling ( Δ T s c \Delta T_{sc} Δ T sc ​ )

Definition: The temperature reduction of a liquid below its saturation (condensing) temperature at the local pressure: Δ T s c = T s a t ( P ) − T a c t u a l \Delta T_{sc} = T_{sat}(P) - T_{actual} Δ T sc ​ = T s a t ​ ( P ) − T a c t u a l ​

HVAC/R Importance: Condenser subcooling ( 10 ∘ F − 15 ∘ F 10^\circ\text{F} - 15^\circ\text{F} 1 0 ∘ F − 1 5 ∘ F ) ensures that solid liquid refrigerant enters the thermostatic expansion valve (TXV), preventing premature flash gas formation in liquid lines and expanding net evaporator cooling capacity ( q e = h 1 − h 4 q_e = h_1 - h_4 q e ​ = h 1 ​ − h 4 ​ ).

4. Compressed Liquid Region & Incompressible Approximations

Water and liquid refrigerants are nearly incompressible fluids. Because compressed liquid property tables are tabulated only at very high pressures, properties in standard HVAC conditions ( P < 500 psia P < 500 \text{ psia} P < 500 psia ) are evaluated using saturated liquid properties at the local fluid temperature : v ( T , P ) ≈ v f ( T ) v(T, P) \approx v_f(T) v ( T , P ) ≈ v f ​ ( T ) ν ( T , P ) ≈ u f ( T ) \nu(T, P) \approx u_f(T) ν ( T , P ) ≈ u f ​ ( T ) s ( T , P ) ≈ s f ( T ) s(T, P) \approx s_f(T) s ( T , P ) ≈ s f ​ ( T ) h ( T , P ) ≈ h f ( T ) + v f ( T ) [ P − P s a t ( T ) ] ≈ h f ( T ) h(T, P) \approx h_f(T) + v_f(T) [P - P_{sat}(T)] \approx h_f(T) h ( T , P ) ≈ h f ​ ( T ) + v f ​ ( T ) [ P − P s a t ​ ( T )] ≈ h f ​ ( T )

For high-pressure boiler feed pumps ( P ≥ 500 psia P \ge 500 \text{ psia} P ≥ 500 psia ), the flow work correction term v f ( T ) [ P − P s a t ( T ) ] v_f(T)[P - P_{sat}(T)] v f ​ ( T ) [ P − P s a t ​ ( T )] becomes significant ( 1 to 5 Btu/lb m 1 \text{ to } 5 \text{ Btu/lb}_m 1 to 5 Btu/lb m ​ ) and must be added: h ( T , P ) = h f ( T ) + v f ( T ) [ P − P s a t ( T ) ] × ( 144 in 2 / ft 2 778.17 ft ⋅ lb f / Btu ) h(T, P) = h_f(T) + v_f(T) [P - P_{sat}(T)] \times \left(\frac{144 \text{ in}^2/\text{ft}^2}{778.17 \text{ ft}\cdot\text{lb}_f/\text{Btu}}\right) h ( T , P ) = h f ​ ( T ) + v f ​ ( T ) [ P − P s a t ​ ( T )] × ( 778.17 ft ⋅ lb f ​ / Btu 144 in 2 / ft 2 ​ )

5. Ideal Gas Equations of State & Gas Mixtures

Gases at temperatures well above their critical temperature ( T ≫ T c T \gg T_c T ≫ T c ​ ) and pressures far below their critical pressure ( P ≪ P c P \ll P_c P ≪ P c ​ ) follow the Ideal Gas Law : P v = R T ⟹ P V = m R T = n R ˉ T P v = R T \quad \implies \quad P V = m R T = n \bar{R} T P v = RT ⟹ P V = m RT = n R ˉ T

Where:

R ˉ = 1545.35 ft ⋅ lb f / ( lbmol ⋅ ∘ R ) = 8.31447 kJ / ( kmol ⋅ K ) = Universal Gas Constant \bar{R} = 1545.35 \text{ ft}\cdot\text{lb}_f/(\text{lbmol}\cdot^\circ\text{R}) = 8.31447 \text{ kJ}/(\text{kmol}\cdot\text{K}) = \text{Universal Gas Constant} R ˉ = 1545.35 ft ⋅ lb f ​ / ( lbmol ⋅ ∘ R ) = 8.31447 kJ / ( kmol ⋅ K ) = Universal Gas Constant

R = R ˉ M = Specific Gas Constant of the gas ( ft ⋅ lb f / ( lb m ⋅ ∘ R ) or kJ / ( kg ⋅ K ) ) R = \frac{\bar{R}}{M} = \text{Specific Gas Constant of the gas } (\text{ft}\cdot\text{lb}_f/(\text{lb}_m\cdot^\circ\text{R}) \text{ or } \text{kJ}/(\text{kg}\cdot\text{K})) R = M R ˉ ​ = Specific Gas Constant of the gas ( ft ⋅ lb f ​ / ( lb m ​ ⋅ ∘ R ) or kJ / ( kg ⋅ K ))

For standard dry air ( M = 28.966 lb m / lbmol M = 28.966 \text{ lb}_m/\text{lbmol} M = 28.966 lb m ​ / lbmol ): R a i r = 53.352 ft ⋅ lb f / ( lb m ⋅ ∘ R ) = 0.06855 Btu / ( lb m ⋅ ∘ R ) R_{air} = 53.352 \text{ ft}\cdot\text{lb}_f/(\text{lb}_m\cdot^\circ\text{R}) = 0.06855 \text{ Btu}/(\text{lb}_m\cdot^\circ\text{R}) R ai r ​ = 53.352 ft ⋅ lb f ​ / ( lb m ​ ⋅ ∘ R ) = 0.06855 Btu / ( lb m ​ ⋅ ∘ R )

Specific Heat Relationships for Ideal Gases

For ideal gases, internal energy and enthalpy depend strictly on temperature ( u = u ( T ) u = u(T) u = u ( T ) , h = h ( T ) h = h(T) h = h ( T ) ): Δ u = u 2 − u 1 = ∫ T 1 T 2 c v ( T ) d T ≈ c v ( T 2 − T 1 ) \Delta u = u_2 - u_1 = \int_{T_1}^{T_2} c_v(T) \, dT \approx c_v (T_2 - T_1) Δ u = u 2 ​ − u 1 ​ = ∫ T 1 ​ T 2 ​ ​ c v ​ ( T ) d T ≈ c v ​ ( T 2 ​ − T 1 ​ ) Δ h = h 2 − h 1 = ∫ T 1 T 2 c p ( T ) d T ≈ c p ( T 2 − T 1 ) \Delta h = h_2 - h_1 = \int_{T_1}^{T_2} c_p(T) \, dT \approx c_p (T_2 - T_1) Δ h = h 2 ​ − h 1 ​ = ∫ T 1 ​ T 2 ​ ​ c p ​ ( T ) d T ≈ c p ​ ( T 2 ​ − T 1 ​ ) Mayer’s Relation: c p − c v = R \text{Mayer's Relation: } c_p - c_v = R Mayer’s Relation: c p ​ − c v ​ = R Specific Heat Ratio: k = c p c v ⟹ c p = k R k − 1 , c v = R k − 1 \text{Specific Heat Ratio: } k = \frac{c_p}{c_v} \implies c_p = \frac{k R}{k - 1}, \quad c_v = \frac{R}{k - 1} Specific Heat Ratio: k = c v ​ c p ​ ​ ⟹ c p ​ = k − 1 k R ​ , c v ​ = k − 1 R ​

6. Real Gas Behavior & Compressibility Factor ( Z Z Z )

When gases approach the saturation curve or operate at high pressures and cryogenic temperatures, intermolecular attractive and repulsive forces cause significant deviations from ideal behavior. The Compressibility Factor ( Z Z Z ) quantifies this deviation: Z = P v R T = v a c t u a l v i d e a l Z = \frac{P v}{R T} = \frac{v_{actual}}{v_{ideal}} Z = RT P v ​ = v i d e a l ​ v a c t u a l ​ ​

When Z = 1.0 Z = 1.0 Z = 1.0 : the fluid behaves as an exact ideal gas.

When Z < 1.0 Z < 1.0 Z < 1.0 (dominant intermolecular attractions) or Z > 1.0 Z > 1.0 Z > 1.0 (molecular volume exclusions), real gas charts or equations of state (Peng-Robinson, Redlich-Kwong, REFPROP) must be utilized.

Principle of Corresponding States

Gases at the same Reduced Pressure ( P r P_r P r ​ ) and Reduced Temperature ( T r T_r T r ​ ) exhibit approximately the same compressibility factor Z Z Z on Nelson-Obert Generalized Compressibility Charts: P r = P P c , T r = T T c , v r ′ = v a c t u a l R T c / P c P_r = \frac{P}{P_c}, \quad T_r = \frac{T}{T_c}, \quad v'_r = \frac{v_{actual}}{R T_c / P_c} P r ​ = P c ​ P ​ , T r ​ = T c ​ T ​ , v r ′ ​ = R T c ​ / P c ​ v a c t u a l ​ ​

Where P c P_c P c ​ and T c T_c T c ​ are the substance critical pressure and critical temperature in absolute units.

Loading diagram... Thermodynamic Phase Regions & Vapor Dome on P-h Coordinates

  • 7. Step-by-Step Worked Example: Steam Heating Coil State Analysis
  • Problem Statement

A central heating coil in an industrial HVAC air handler receives superheated steam at P 1 = 100.0 psia P_1 = 100.0\text{ psia} P 1 ​ = 100.0 psia and T 1 = 400.0 ∘ F T_1 = 400.0^\circ\text{F} T 1 ​ = 400. 0 ∘ F at a steady mass flow rate of m ˙ = 1 , 500 lbm/hr \dot{m} = 1,500\text{ lbm/hr} m ˙ = 1 , 500 lbm/hr . The steam condenses and cools as it passes through the coil, exiting as subcooled liquid condensate at P 2 = 90.0 psia P_2 = 90.0\text{ psia} P 2 ​ = 90.0 psia and T 2 = 180.0 ∘ F T_2 = 180.0^\circ\text{F} T 2 ​ = 180. 0 ∘ F .

From NCEES steam property tables:

At 100.0 psia 100.0\text{ psia} 100.0 psia : T s a t = 327.86 ∘ F T_{sat} = 327.86^\circ\text{F} T s a t ​ = 327.8 6 ∘ F , h f = 298.61 Btu/lbm h_f = 298.61\text{ Btu/lbm} h f ​ = 298.61 Btu/lbm , h f g = 889.2 Btu/lbm h_{fg} = 889.2\text{ Btu/lbm} h f g ​ = 889.2 Btu/lbm , h g = 1187.8 Btu/lbm h_g = 1187.8\text{ Btu/lbm} h g ​ = 1187.8 Btu/lbm .

Superheated Steam at 100.0 psia 100.0\text{ psia} 100.0 psia and 400.0 ∘ F 400.0^\circ\text{F} 400. 0 ∘ F : h 1 = 1227.5 Btu/lbm h_1 = 1227.5\text{ Btu/lbm} h 1 ​ = 1227.5 Btu/lbm , v 1 = 4.934 ft 3 / lbm v_1 = 4.934\text{ ft}^3/\text{lbm} v 1 ​ = 4.934 ft 3 / lbm , s 1 = 1.6517 Btu/(lbm ⋅ ∘ R) s_1 = 1.6517\text{ Btu/(lbm}\cdot^\circ\text{R)} s 1 ​ = 1.6517 Btu/(lbm ⋅ ∘ R) .

At 90.0 psia 90.0\text{ psia} 90.0 psia : T s a t = 320.27 ∘ F T_{sat} = 320.27^\circ\text{F} T s a t ​ = 320.2 7 ∘ F , h f = 290.73 Btu/lbm h_f = 290.73\text{ Btu/lbm} h f ​ = 290.73 Btu/lbm , h f g = 895.0 Btu/lbm h_{fg} = 895.0\text{ Btu/lbm} h f g ​ = 895.0 Btu/lbm , h g = 1185.7 Btu/lbm h_g = 1185.7\text{ Btu/lbm} h g ​ = 1185.7 Btu/lbm .

Saturated Liquid Water at 180.0 ∘ F 180.0^\circ\text{F} 180. 0 ∘ F : P s a t = 7.515 psia P_{sat} = 7.515\text{ psia} P s a t ​ = 7.515 psia , h f = 147.99 Btu/lbm h_f = 147.99\text{ Btu/lbm} h f ​ = 147.99 Btu/lbm , v f = 0.01651 ft 3 / lbm v_f = 0.01651\text{ ft}^3/\text{lbm} v f ​ = 0.01651 ft 3 / lbm .

Calculate:

The degrees of superheat at the coil inlet ( Δ T s h , 1 \Delta T_{sh,1} Δ T s h , 1 ​ ).

The degrees of subcooling at the coil exit ( Δ T s c , 2 \Delta T_{sc,2} Δ T sc , 2 ​ ).

The exit specific enthalpy ( h 2 h_2 h 2 ​ ) using compressed liquid evaluation.

The total rate of thermal heat transfer released to the building supply air stream ( Q ˙ c o i l \dot{Q}_{coil} Q ˙ ​ co i l ​ ) in Btu/hr \text{Btu/hr} Btu/hr and MBH \text{MBH} MBH .

Solution Steps

Step 1: Determine inlet degrees of superheat At P 1 = 100.0 psia P_1 = 100.0\text{ psia} P 1 ​ = 100.0 psia , T s a t , 1 = 327.86 ∘ F T_{sat,1} = 327.86^\circ\text{F} T s a t , 1 ​ = 327.8 6 ∘ F . Δ T s h , 1 = T 1 − T s a t , 1 = 400.0 ∘ F − 327.86 ∘ F = 72.14 ∘ F \Delta T_{sh,1} = T_1 - T_{sat,1} = 400.0^\circ\text{F} - 327.86^\circ\text{F} = 72.14^\circ\text{F} Δ T s h , 1 ​ = T 1 ​ − T s a t , 1 ​ = 400. 0 ∘ F − 327.8 6 ∘ F = 72.1 4 ∘ F

Step 2: Determine exit degrees of subcooling At P 2 = 90.0 psia P_2 = 90.0\text{ psia} P 2 ​ = 90.0 psia , T s a t , 2 = 320.27 ∘ F T_{sat,2} = 320.27^\circ\text{F} T s a t , 2 ​ = 320.2 7 ∘ F . The exit temperature is T 2 = 180.0 ∘ F T_2 = 180.0^\circ\text{F} T 2 ​ = 180. 0 ∘ F . Δ T s c , 2 = T s a t , 2 − T 2 = 320.27 ∘ F − 180.0 ∘ F = 140.27 ∘ F \Delta T_{sc,2} = T_{sat,2} - T_2 = 320.27^\circ\text{F} - 180.0^\circ\text{F} = 140.27^\circ\text{F} Δ T sc , 2 ​ = T s a t , 2 ​ − T 2 ​ = 320.2 7 ∘ F − 180. 0 ∘ F = 140.2 7 ∘ F

Step 3: Evaluate exit specific enthalpy ( h 2 h_2 h 2 ​ ) Using the incompressible liquid approximation evaluated at local temperature T 2 = 180.0 ∘ F T_2 = 180.0^\circ\text{F} T 2 ​ = 180. 0 ∘ F with the flow work correction term: h 2 = h f ( 180 ∘ F ) + v f ( 180 ∘ F ) × [ P 2 − P s a t ( 180 ∘ F ) ] × ( 144 778.17 ) h_2 = h_f(180^\circ\text{F}) + v_f(180^\circ\text{F}) \times [P_2 - P_{sat}(180^\circ\text{F})] \times \left(\frac{144}{778.17}\right) h 2 ​ = h f ​ ( 18 0 ∘ F ) + v f ​ ( 18 0 ∘ F ) × [ P 2 ​ − P s a t ​ ( 18 0 ∘ F )] × ( 778.17 144 ​ ) h 2 = 147.99 + 0.01651 × [ 90.0 − 7.515 ] × 0.18505 h_2 = 147.99 + 0.01651 \times [90.0 - 7.515] \times 0.18505 h 2 ​ = 147.99 + 0.01651 × [ 90.0 − 7.515 ] × 0.18505 h 2 = 147.99 + 0.01651 × 82.485 × 0.18505 = 147.99 + 0.252 = 148.24 Btu/lbm h_2 = 147.99 + 0.01651 \times 82.485 \times 0.18505 = 147.99 + 0.252 = 148.24\text{ Btu/lbm} h 2 ​ = 147.99 + 0.01651 × 82.485 × 0.18505 = 147.99 + 0.252 = 148.24 Btu/lbm

(Note: Saturated liquid approximation h 2 ≈ h f ( 180 ∘ F ) = 147.99 Btu/lbm h_2 \approx h_f(180^\circ\text{F}) = 147.99\text{ Btu/lbm} h 2 ​ ≈ h f ​ ( 18 0 ∘ F ) = 147.99 Btu/lbm is accurate within 0.17 % 0.17\% 0.17% ). We use h 2 = 148.24 Btu/lbm h_2 = 148.24\text{ Btu/lbm} h 2 ​ = 148.24 Btu/lbm .

Step 4: Calculate total heat transfer duty Q ˙ c o i l \dot{Q}_{coil} Q ˙ ​ co i l ​ Applying the steady-state open system energy balance: Q ˙ c o i l = m ˙ ( h 1 − h 2 ) \dot{Q}_{coil} = \dot{m} (h_1 - h_2) Q ˙ ​ co i l ​ = m ˙ ( h 1 ​ − h 2 ​ ) Q ˙ c o i l = 1 , 500 lbm/hr × ( 1227.5 − 148.24 Btu/lbm ) \dot{Q}_{coil} = 1,500\text{ lbm/hr} \times (1227.5 - 148.24\text{ Btu/lbm}) Q ˙ ​ co i l ​ = 1 , 500 lbm/hr × ( 1227.5 − 148.24 Btu/lbm ) Q ˙ c o i l = 1 , 500 × 1079.26 = 1 , 618 , 890 Btu/hr \dot{Q}_{coil} = 1,500 \times 1079.26 = 1,618,890\text{ Btu/hr} Q ˙ ​ co i l ​ = 1 , 500 × 1079.26 = 1 , 618 , 890 Btu/hr

Converting to MBH \text{MBH} MBH ( 1 MBH = 1 , 000 Btu/hr 1\text{ MBH} = 1,000\text{ Btu/hr} 1 MBH = 1 , 000 Btu/hr ): Q ˙ c o i l = 1 , 618 , 890 1 , 000 = 1618.9 MBH \dot{Q}_{coil} = \frac{1,618,890}{1,000} = 1618.9\text{ MBH} Q ˙ ​ co i l ​ = 1 , 000 1 , 618 , 890 ​ = 1618.9 MBH

This validates that steam heating coils yield exceptionally high thermal heat duty primarily due to latent heat release during phase change ( h f g ≈ 895 Btu/lbm h_{fg} \approx 895\text{ Btu/lbm} h f g ​ ≈ 895 Btu/lbm ).