Study guide

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances

PE Mechanical: HVAC and Refrigeration Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations

1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)

2 Chapter 2: Thermodynamics & Energy Balances

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment

3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment

3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes

4 Chapter 4: Heat Transfer Principles & Sizing

4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)

5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals

5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves

6 Chapter 6: Heating & Cooling Load Calculations

6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis

7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications

7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design

8 Chapter 8: Refrigerants, Environmental Regulations & Safety

8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers

9 Chapter 9: HVAC Equipment & Primary Machinery

9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems

10 Chapter 10: Air-Side Systems & Distribution

10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection

11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant

11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems

12 Chapter 12: HVAC Control Concepts, Sensors & Sequences

12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences

13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes

13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops

14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations

14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances

Key Takeaways Explain This Topic AI

Closed systems (control mass) exchange energy but not mass with surroundings; boundary work for polytropic processes ( P V n = C P V^n = C P V n = C ) requires specific integration depending on whether n = 1 n=1 n = 1 (isothermal ideal gas) or n ≠ 1 n \ne 1 n  = 1 .

Steady-State Steady-Flow (SS-SF) open systems balance mass ∑ m ˙ i n = ∑ m ˙ o u t \sum \dot{m}_{in} = \sum \dot{m}_{out} ∑ m ˙ in ​ = ∑ m ˙ o u t ​ and energy Q ˙ − W ˙ c v = ∑ m ˙ o u t ( h o u t + V o u t 2 2 + g z o u t ) − ∑ m ˙ i n ( h i n + V i n 2 2 + g z i n ) \dot{Q} - \dot{W}_{cv} = \sum \dot{m}_{out}(h_{out} + \frac{V_{out}^2}{2} + g z_{out}) - \sum \dot{m}_{in}(h_{in} + \frac{V_{in}^2}{2} + g z_{in}) Q ˙ ​ − W ˙ c v ​ = ∑ m ˙ o u t ​ ( h o u t ​ + 2 V o u t 2 ​ ​ + g z o u t ​ ) − ∑ m ˙ in ​ ( h in ​ + 2 V in 2 ​ ​ + g z in ​ ) .

Throttling valves and expansion devices operate isenthalpically ( h 1 = h 2 h_1 = h_2 h 1 ​ = h 2 ​ ) with negligible heat transfer, work, and kinetic/potential energy changes, producing temperature drops via the Joule-Thomson effect.

Isentropic efficiency quantifies irreversibilities: for compressors and pumps η c = h 2 s − h 1 h 2 − h 1 = w s w a ≤ 1.0 \eta_c = \frac{h_{2s} - h_1}{h_2 - h_1} = \frac{w_s}{w_a} \le 1.0 η c ​ = h 2 ​ − h 1 ​ h 2 s ​ − h 1 ​ ​ = w a ​ w s ​ ​ ≤ 1.0 , while for turbines η t = h 1 − h 2 h 1 − h 2 s = w a w s ≤ 1.0 \eta_t = \frac{h_1 - h_2}{h_1 - h_{2s}} = \frac{w_a}{w_s} \le 1.0 η t ​ = h 1 ​ − h 2 s ​ h 1 ​ − h 2 ​ ​ = w s ​ w a ​ ​ ≤ 1.0 .

The Second Law dictates that entropy is generated ( S g e n ≥ 0 S_{gen} \ge 0 S g e n ​ ≥ 0 ) in all real processes; isentropic processes represent the ideal reversible and adiabatic benchmark.

Last updated: August 2026

2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances

Thermodynamic energy balances form the core of every calculation on the PE Mechanical: HVAC and Refrigeration exam. Whether analyzing a 500-ton centrifugal chiller, a steam heating coil, an air handler economizer, or a thermal expansion valve, engineers must systematically define control volumes, track energy and mass flows, apply property relations, and account for second-law irreversibilities.

1. Thermodynamic System Definitions & Sign Conventions

Before writing an energy equation, clearly classify the system boundary:

Closed System (Control Mass): A fixed quantity of matter. No mass crosses the boundary ( m = constant m = \text{constant} m = constant ), but energy crosses as heat ( Q Q Q ) and work ( W W W ). Examples include a sealed refrigerant storage cylinder or a rigid refrigerant charging cylinder.

Open System (Control Volume): A designated region in space through which mass flows. Mass, heat, and work can all cross the control surface. Examples include compressors, evaporators, cooling towers, fans, pumps, and mixing boxes.

Isolated System: Neither mass nor energy crosses the boundary (e.g., an adiabatic rigid container).

Standard Sign Convention (NCEES Reference Handbook)

In standard mechanical engineering thermodynamics:

Heat Transfer ( Q Q Q , Q ˙ \dot{Q} Q ˙ ​ ): Positive ( + + + ) when heat is transferred INTO the system from the surroundings; Negative ( − - − ) when heat is transferred OUT OF the system to the surroundings.

Work Transfer ( W W W , W ˙ \dot{W} W ˙ ): Positive ( + + + ) when work is done BY the system on the surroundings (e.g., turbine shaft work output); Negative ( − - − ) when work is done ON the system by the surroundings (e.g., compressor or pump power input). Δ E s y s t e m = Q i n − W o u t = Q n e t , i n − W n e t , o u t \Delta E_{system} = Q_{in} - W_{out} = Q_{net,in} - W_{net,out} Δ E sys t e m ​ = Q in ​ − W o u t ​ = Q n e t , in ​ − W n e t , o u t ​ d E c v d t = Q ˙ − W ˙ + ∑ m ˙ i n ( h + V 2 2 + g z ) i n − ∑ m ˙ o u t ( h + V 2 2 + g z ) o u t \frac{dE_{cv}}{dt} = \dot{Q} - \dot{W} + \sum \dot{m}_{in} \left(h + \frac{V^2}{2} + gz\right)_{in} - \sum \dot{m}_{out} \left(h + \frac{V^2}{2} + gz\right)_{out} d t d E c v ​ ​ = Q ˙ ​ − W ˙ + ∑ m ˙ in ​ ( h + 2 V 2 ​ + g z ) in ​ − ∑ m ˙ o u t ​ ( h + 2 V 2 ​ + g z ) o u t ​

2. Closed System Energy Balances & Polytropic Processes

For a stationary closed system (where changes in macroscopic kinetic and potential energy are zero, Δ K E = Δ P E = 0 \Delta KE = \Delta PE = 0 Δ K E = Δ PE = 0 ), the First Law reduces to: Q − W = Δ U = m ( u 2 − u 1 ) Q - W = \Delta U = m (u_2 - u_1) Q − W = Δ U = m ( u 2 ​ − u 1 ​ )

Where u u u is specific internal energy ( Btu/lb m \text{Btu/lb}_m Btu/lb m ​ or kJ/kg \text{kJ/kg} kJ/kg ). For an ideal gas with constant specific heats, Δ u = c v ( T 2 − T 1 ) \Delta u = c_v (T_2 - T_1) Δ u = c v ​ ( T 2 ​ − T 1 ​ ) and Δ h = c p ( T 2 − T 1 ) \Delta h = c_p (T_2 - T_1) Δ h = c p ​ ( T 2 ​ − T 1 ​ ) .

Boundary Work ( P d V P\,dV P d V Work)

Boundary work done during a quasi-equilibrium expansion or compression process is: W b = ∫ 1 2 P d V W_b = \int_1^2 P \, dV W b ​ = ∫ 1 2 ​ P d V

Polytropic processes follow the pressure-volume relationship P V n = C P V^n = C P V n = C , where n n n is the polytropic index:

Process Type Polytropic Exponent ( n n n ) Boundary Work Equation ( W b W_b W b ​ ) Ideal Gas Property Relations

Isobaric (Constant Pressure) n = 0 n = 0 n = 0 W b = P ( V 2 − V 1 ) = m P ( v 2 − v 1 ) W_b = P (V_2 - V_1) = m P (v_2 - v_1) W b ​ = P ( V 2 ​ − V 1 ​ ) = m P ( v 2 ​ − v 1 ​ ) V 1 T 1 = V 2 T 2 , Q = m c p ( T 2 − T 1 ) = m ( h 2 − h 1 ) \frac{V_1}{T_1} = \frac{V_2}{T_2},\quad Q = m c_p (T_2 - T_1) = m (h_2 - h_1) T 1 ​ V 1 ​ ​ = T 2 ​ V 2 ​ ​ , Q = m c p ​ ( T 2 ​ − T 1 ​ ) = m ( h 2 ​ − h 1 ​ )

Isochoric / Isometric (Constant Volume) n = ∞ n = \infty n = ∞ W b = 0 W_b = 0 W b ​ = 0 P 1 T 1 = P 2 T 2 , Q = m c v ( T 2 − T 1 ) = m ( u 2 − u 1 ) \frac{P_1}{T_1} = \frac{P_2}{T_2},\quad Q = m c_v (T_2 - T_1) = m (u_2 - u_1) T 1 ​ P 1 ​ ​ = T 2 ​ P 2 ​ ​ , Q = m c v ​ ( T 2 ​ − T 1 ​ ) = m ( u 2 ​ − u 1 ​ )

Isothermal (Constant Temperature, Ideal Gas) n = 1 n = 1 n = 1 W b = P 1 V 1 ln ⁡ ( V 2 V 1 ) = m R T ln ⁡ ( P 1 P 2 ) W_b = P_1 V_1 \ln\left(\frac{V_2}{V_1}\right) = m R T \ln\left(\frac{P_1}{P_2}\right) W b ​ = P 1 ​ V 1 ​ ln ( V 1 ​ V 2 ​ ​ ) = m RT ln ( P 2 ​ P 1 ​ ​ ) P 1 V 1 = P 2 V 2 , Δ U = 0 ⟹ Q = W b P_1 V_1 = P_2 V_2,\quad \Delta U = 0 \implies Q = W_b P 1 ​ V 1 ​ = P 2 ​ V 2 ​ , Δ U = 0 ⟹ Q = W b ​

Polytropic (General, n ≠ 1 n \ne 1 n  = 1 ) n ≠ 1 n \ne 1 n  = 1 W b = P 2 V 2 − P 1 V 1 1 − n = m R ( T 2 − T 1 ) 1 − n W_b = \frac{P_2 V_2 - P_1 V_1}{1 - n} = \frac{m R (T_2 - T_1)}{1 - n} W b ​ = 1 − n P 2 ​ V 2 ​ − P 1 ​ V 1 ​ ​ = 1 − n m R ( T 2 ​ − T 1 ​ ) ​ P 1 V 1 n = P 2 V 2 n , T 2 T 1 = ( P 2 P 1 ) n − 1 n = ( V 1 V 2 ) n − 1 P_1 V_1^n = P_2 V_2^n,\quad \frac{T_2}{T_1} = \left(\frac{P_2}{P_1}\right)^{\frac{n-1}{n}} = \left(\frac{V_1}{V_2}\right)^{n-1} P 1 ​ V 1 n ​ = P 2 ​ V 2 n ​ , T 1 ​ T 2 ​ ​ = ( P 1 ​ P 2 ​ ​ ) n n − 1 ​ = ( V 2 ​ V 1 ​ ​ ) n − 1

Isentropic (Reversible Adiabatic, Ideal Gas) n = k = c p c v n = k = \frac{c_p}{c_v} n = k = c v ​ c p ​ ​ W b = P 2 V 2 − P 1 V 1 1 − k = m R ( T 2 − T 1 ) 1 − k = − m c v ( T 2 − T 1 ) W_b = \frac{P_2 V_2 - P_1 V_1}{1 - k} = \frac{m R (T_2 - T_1)}{1 - k} = -m c_v (T_2 - T_1) W b ​ = 1 − k P 2 ​ V 2 ​ − P 1 ​ V 1 ​ ​ = 1 − k m R ( T 2 ​ − T 1 ​ ) ​ = − m c v ​ ( T 2 ​ − T 1 ​ ) P 1 V 1 k = P 2 V 2 k , Q = 0 ⟹ W b = − Δ U P_1 V_1^k = P_2 V_2^k,\quad Q = 0 \implies W_b = -\Delta U P 1 ​ V 1 k ​ = P 2 ​ V 2 k ​ , Q = 0 ⟹ W b ​ = − Δ U

NCEES Exam Strategy — Polytropic Index Sign Traps: When computing W b = P 2 V 2 − P 1 V 1 1 − n W_b = \frac{P_2 V_2 - P_1 V_1}{1 - n} W b ​ = 1 − n P 2 ​ V 2 ​ − P 1 ​ V 1 ​ ​ , ensure consistent units. In US Customary units, P P P is often in psia \text{psia} psia (or lb f / in 2 \text{lb}_f/\text{in}^2 lb f ​ / in 2 ) and V V V is in ft 3 \text{ft}^3 ft 3 . You must multiply by 144 in 2 / ft 2 144 \text{ in}^2/\text{ft}^2 144 in 2 / ft 2 to convert pressure to lb f / ft 2 \text{lb}_f/\text{ft}^2 lb f ​ / ft 2 before evaluating work in ft ⋅ lb f \text{ft}\cdot\text{lb}_f ft ⋅ lb f ​ , and then divide by 778.17 ft ⋅ lb f / Btu 778.17 \text{ ft}\cdot\text{lb}_f/\text{Btu} 778.17 ft ⋅ lb f ​ / Btu if the question asks for work in Btu \text{Btu} Btu !

3. Open System Steady-State Steady-Flow (SS-SF) Energy Balances

Most HVAC and refrigeration equipment operates under steady-state steady-flow (SS-SF) conditions, meaning fluid properties at any spatial point within the control volume do not change over time ( d m c v d t = 0 \frac{dm_{cv}}{dt} = 0 d t d m c v ​ ​ = 0 , d E c v d t = 0 \frac{dE_{cv}}{dt} = 0 d t d E c v ​ ​ = 0 ).

Conservation of Mass ∑ m ˙ i n = ∑ m ˙ o u t \sum \dot{m}_{in} = \sum \dot{m}_{out} ∑ m ˙ in ​ = ∑ m ˙ o u t ​ m ˙ = ρ A V = A V v = V ˙ v \dot{m} = \rho A V = \frac{A V}{v} = \frac{\dot{V}}{v} m ˙ = ρ A V = v A V ​ = v V ˙ ​

Where m ˙ \dot{m} m ˙ is mass flow rate ( lb m / s \text{lb}_m/\text{s} lb m ​ / s or lb m / hr \text{lb}_m/\text{hr} lb m ​ / hr ), V ˙ \dot{V} V ˙ is volumetric flow rate ( CFM \text{CFM} CFM or ft 3 / min \text{ft}^3/\text{min} ft 3 / min ), v v v is specific volume ( ft 3 / lb m \text{ft}^3/\text{lb}_m ft 3 / lb m ​ ), A A A is cross-sectional area ( ft 2 \text{ft}^2 ft 2 ), and V V V is velocity ( ft/s \text{ft/s} ft/s ).

Conservation of Energy (First Law for Open Systems) Q ˙ − W ˙ c v = ∑ m ˙ o u t ( h o u t + V o u t 2 2 g c + g z o u t g c ) − ∑ m ˙ i n ( h i n + V i n 2 2 g c + g z i n g c ) \dot{Q} - \dot{W}_{cv} = \sum \dot{m}_{out} \left(h_{out} + \frac{V_{out}^2}{2 g_c} + \frac{g z_{out}}{g_c}\right) - \sum \dot{m}_{in} \left(h_{in} + \frac{V_{in}^2}{2 g_c} + \frac{g z_{in}}{g_c}\right) Q ˙ ​ − W ˙ c v ​ = ∑ m ˙ o u t ​ ( h o u t ​ + 2 g c ​ V o u t 2 ​ ​ + g c ​ g z o u t ​ ​ ) − ∑ m ˙ in ​ ( h in ​ + 2 g c ​ V in 2 ​ ​ + g c ​ g z in ​ ​ )

In US Customary units, kinetic energy V 2 2 g c \frac{V^2}{2 g_c} 2 g c ​ V 2 ​ with V V V in ft/s \text{ft/s} ft/s has units of ft ⋅ lb f / lb m \text{ft}\cdot\text{lb}_f/\text{lb}_m ft ⋅ lb f ​ / lb m ​ . To convert to Btu/lb m \text{Btu/lb}_m Btu/lb m ​ , divide by 778.17 ft ⋅ lb f / Btu 778.17 \text{ ft}\cdot\text{lb}_f/\text{Btu} 778.17 ft ⋅ lb f ​ / Btu : Specific Kinetic Energy (Btu/lb m ) = V 2 2 × 32.174 × 778.17 = V 2 50 , 073 \text{Specific Kinetic Energy (Btu/lb}_m\text{)} = \frac{V^2}{2 \times 32.174 \times 778.17} = \frac{V^2}{50,073} Specific Kinetic Energy (Btu/lb m ​ ) = 2 × 32.174 × 778.17 V 2 ​ = 50 , 073 V 2 ​

In most HVAC components (pumps, compressors, coils, valves), kinetic and potential energy changes ( Δ k e \Delta ke Δ k e and Δ p e \Delta pe Δ p e ) are negligible compared to enthalpy changes ( Δ h \Delta h Δ h ), reducing the energy equation for single-inlet single-outlet devices to: q ˙ − w c v = h e − h i ⟹ Q ˙ − W ˙ c v = m ˙ ( h e − h i ) \dot{q} - w_{cv} = h_e - h_i \implies \dot{Q} - \dot{W}_{cv} = \dot{m} (h_e - h_i) q ˙ ​ − w c v ​ = h e ​ − h i ​ ⟹ Q ˙ ​ − W ˙ c v ​ = m ˙ ( h e ​ − h i ​ )

Energy Balances for Primary HVAC/R Equipment +-----------------------+------------------------+---------------------------------------------+

  • | Component | Simplifying Assumption | Governing Energy Balance |
  • +-----------------------+------------------------+---------------------------------------------+
  • | Compressor / Pump | Adiabatic (\dot{Q}=0) | \dot{W}_{in} = \dot{m}(h_{out} - h_{in}) |
  • | Turbine / Expander | Adiabatic (\dot{Q}=0) | \dot{W}_{out} = \dot{m}(h_{in} - h_{out}) |
  • | Heat Exchanger (Coil) | No Shaft Work (\dot{W}=0)| \dot{Q} = \dot{m}(h_{out} - h_{in}) |
  • | Throttling Device (TXV)| Adiabatic & Rigid | h_{out} = h_{in} (Isenthalpic) |
  • | Mixing Chamber / Box | Adiabatic & Rigid | \sum \dot{m}_{in} h_{in} = \dot{m}_{out} h_{out} |

| Nozzle / Diffuser | Adiabatic (\dot{Q}=\dot{W}=0)| h_{in} + \frac{V_{in}^2}{2} = h_{out} + \frac{V_{out}^2}{2} |

  • +-----------------------+------------------------+---------------------------------------------+
  • 4. Second Law of Thermodynamics, Entropy & Isentropic Efficiency

The First Law establishes that energy is conserved; the Second Law dictates the direction of spontaneous processes and establishes theoretical limits on efficiency and performance.

Classical Statements of the Second Law

Kelvin-Planck Statement: It is impossible for any device operating on a thermodynamic cycle to receive heat from a single thermal reservoir and produce a net amount of work (i.e., thermal efficiency η t h < 100 % \eta_{th} < 100\% η t h ​ < 100% ).

Clausius Statement: It is impossible to construct a device that operates in a cycle and produces no effect other than the transfer of heat from a lower-temperature body to a higher-temperature body without external work input (i.e., refrigeration COP is finite and requires compressor power).

Entropy and the T-ds Equations

Entropy ( S S S ) is a thermodynamic state property defined for a reversible process by d S = ( δ Q T ) r e v dS = \left(\frac{\delta Q}{T}\right)_{rev} d S = ( T δ Q ​ ) re v ​ . For any real (irreversible) process: d S = δ Q T + δ S g e n where δ S g e n > 0 dS = \frac{\delta Q}{T} + \delta S_{gen} \quad \text{where } \delta S_{gen} > 0 d S = T δ Q ​ + δ S g e n ​ where δ S g e n ​ > 0

For a closed system undergoing an adiabatic process ( δ Q = 0 \delta Q = 0 δ Q = 0 ), Δ S = S g e n ≥ 0 \Delta S = S_{gen} \ge 0 Δ S = S g e n ​ ≥ 0 . Entropy can be generated, but it can never be destroyed.

The fundamental differential property relations (Gibbs equations) hold for all processes (reversible or irreversible): T d s = d u + P d v T\,ds = du + P\,dv T d s = d u + P d v T d s = d h − v d P T\,ds = dh - v\,dP T d s = d h − v d P

For an ideal gas with constant specific heats: s 2 − s 1 = c v ln ⁡ ( T 2 T 1 ) + R ln ⁡ ( v 2 v 1 ) s_2 - s_1 = c_v \ln\left(\frac{T_2}{T_1}\right) + R \ln\left(\frac{v_2}{v_1}\right) s 2 ​ − s 1 ​ = c v ​ ln ( T 1 ​ T 2 ​ ​ ) + R ln ( v 1 ​ v 2 ​ ​ ) s 2 − s 1 = c p ln ⁡ ( T 2 T 1 ) − R ln ⁡ ( P 2 P 1 ) s_2 - s_1 = c_p \ln\left(\frac{T_2}{T_1}\right) - R \ln\left(\frac{P_2}{P_1}\right) s 2 ​ − s 1 ​ = c p ​ ln ( T 1 ​ T 2 ​ ​ ) − R ln ( P 1 ​ P 2 ​ ​ )

For an isentropic process ( s 2 = s 1 s_2 = s_1 s 2 ​ = s 1 ​ , reversible and adiabatic) of an ideal gas: T 2 T 1 = ( P 2 P 1 ) k − 1 k = ( v 1 v 2 ) k − 1 \frac{T_2}{T_1} = \left(\frac{P_2}{P_1}\right)^{\frac{k-1}{k}} = \left(\frac{v_1}{v_2}\right)^{k-1} T 1 ​ T 2 ​ ​ = ( P 1 ​ P 2 ​ ​ ) k k − 1 ​ = ( v 2 ​ v 1 ​ ​ ) k − 1

Isentropic Efficiency

In actual turbomachinery, fluid friction, turbulence, and heat leakage generate entropy, causing real expansion and compression paths to deviate from the ideal vertical line on a T − s T-s T − s or h − s h-s h − s (Mollier) diagram. Turbine Isentropic Efficiency: η t = Actual Work Isentropic Work = w a w s = h 1 − h 2 a h 1 − h 2 s \text{Turbine Isentropic Efficiency: } \eta_t = \frac{\text{Actual Work}}{\text{Isentropic Work}} = \frac{w_a}{w_s} = \frac{h_1 - h_{2a}}{h_1 - h_{2s}} Turbine Isentropic Efficiency: η t ​ = Isentropic Work Actual Work ​ = w s ​ w a ​ ​ = h 1 ​ − h 2 s ​ h 1 ​ − h 2 a ​ ​ Compressor / Pump Isentropic Efficiency: η c = Isentropic Work Actual Work = w s w a = h 2 s − h 1 h 2 a − h 1 \text{Compressor / Pump Isentropic Efficiency: } \eta_c = \frac{\text{Isentropic Work}}{\text{Actual Work}} = \frac{w_s}{w_a} = \frac{h_{2s} - h_1}{h_{2a} - h_1} Compressor / Pump Isentropic Efficiency: η c ​ = Actual Work Isentropic Work ​ = w a ​ w s ​ ​ = h 2 a ​ − h 1 ​ h 2 s ​ − h 1 ​ ​ Enthalpy (h) / Temperature (T)

  • ^
  • | 2a (Actual: higher h, s2a > s1)
  • | /
  • | 2s / (Compressor Path: w_actual = h2a - h1 > w_s = h2s - h1)
  • | | / eta_c = (h2s - h1) / (h2a - h1)
  • P2 --+----------+---/----
  • | | /
  • | | /
  • | 1 (Inlet)
  • P1 --+----------+---------------------> Entropy (s)
  • s1 = s2s
  • 5. Worked Example: Compressor Power with Heat Loss and Isentropic Efficiency

Problem: An industrial R-134a refrigeration compressor receives saturated vapor at 20 psia 20 \text{ psia} 20 psia ( h 1 = 105.30 Btu/lb m h_1 = 105.30 \text{ Btu/lb}_m h 1 ​ = 105.30 Btu/lb m ​ , s 1 = 0.2248 Btu/lb m ⋅ ∘ R s_1 = 0.2248 \text{ Btu/lb}_m\cdot^\circ\text{R} s 1 ​ = 0.2248 Btu/lb m ​ ⋅ ∘ R ) and compresses it to a discharge pressure of 140 psia 140 \text{ psia} 140 psia . At 140 psia 140 \text{ psia} 140 psia , an isentropic compression to s 2 s = 0.2248 Btu/lb m ⋅ ∘ R s_{2s} = 0.2248 \text{ Btu/lb}_m\cdot^\circ\text{R} s 2 s ​ = 0.2248 Btu/lb m ​ ⋅ ∘ R gives an ideal enthalpy of h 2 s = 124.80 Btu/lb m h_{2s} = 124.80 \text{ Btu/lb}_m h 2 s ​ = 124.80 Btu/lb m ​ . The compressor has an isentropic efficiency of η c = 0.78 \eta_c = 0.78 η c ​ = 0.78 . During operation, the compressor loses heat to the ambient air at a rate of Q ˙ l o s s = 1.80 Btu/lb m \dot{Q}_{loss} = 1.80 \text{ Btu/lb}_m Q ˙ ​ l oss ​ = 1.80 Btu/lb m ​ of refrigerant circulated. The mass flow rate of refrigerant is m ˙ = 120 lb m / min \dot{m} = 120 \text{ lb}_m/\text{min} m ˙ = 120 lb m ​ / min .

Find:

The actual specific work input ( w a c t u a l w_{actual} w a c t u a l ​ ) required by the compressor in Btu/lb m \text{Btu/lb}_m Btu/lb m ​ .

The actual discharge enthalpy ( h 2 a h_{2a} h 2 a ​ ) of the refrigerant exiting the compressor in Btu/lb m \text{Btu/lb}_m Btu/lb m ​ .

The total electrical/brake horsepower ( H P HP H P ) required if the mechanical-electrical drive train efficiency is η m e c h = 0.92 \eta_{mech} = 0.92 η m ec h ​ = 0.92 .

Step-by-Step Solution:

Step 1: Calculate isentropic work and actual work. w s = h 2 s − h 1 = 124.80 − 105.30 = 19.50 Btu/lb m w_s = h_{2s} - h_1 = 124.80 - 105.30 = 19.50 \text{ Btu/lb}_m w s ​ = h 2 s ​ − h 1 ​ = 124.80 − 105.30 = 19.50 Btu/lb m ​

By definition of compressor isentropic efficiency: w a = w s η c = 19.50 Btu/lb m 0.78 = 25.00 Btu/lb m w_a = \frac{w_s}{\eta_c} = \frac{19.50 \text{ Btu/lb}_m}{0.78} = 25.00 \text{ Btu/lb}_m w a ​ = η c ​ w s ​ ​ = 0.78 19.50 Btu/lb m ​ ​ = 25.00 Btu/lb m ​

Step 2: Apply the open system First Law energy balance to find actual discharge enthalpy h 2 a h_{2a} h 2 a ​ . q ˙ n e t , i n − w a = h 2 a − h 1 \dot{q}_{net,in} - w_a = h_{2a} - h_1 q ˙ ​ n e t , in ​ − w a ​ = h 2 a ​ − h 1 ​

Here, heat is lost from the control volume, so q ˙ n e t , i n = − q ˙ l o s s = − 1.80 Btu/lb m \dot{q}_{net,in} = -\dot{q}_{loss} = -1.80 \text{ Btu/lb}_m q ˙ ​ n e t , in ​ = − q ˙ ​ l oss ​ = − 1.80 Btu/lb m ​ . Work is done on the fluid, so w a = − 25.00 Btu/lb m w_a = -25.00 \text{ Btu/lb}_m w a ​ = − 25.00 Btu/lb m ​ under the sign convention q ˙ − w = Δ h \dot{q} - w = \Delta h q ˙ ​ − w = Δ h , or directly writing an energy balance: h 1 + w a − q l o s s = h 2 a h_1 + w_a - q_{loss} = h_{2a} h 1 ​ + w a ​ − q l oss ​ = h 2 a ​ h 2 a = 105.30 + 25.00 − 1.80 = 128.50 Btu/lb m h_{2a} = 105.30 + 25.00 - 1.80 = 128.50 \text{ Btu/lb}_m h 2 a ​ = 105.30 + 25.00 − 1.80 = 128.50 Btu/lb m ​

Step 3: Calculate the total power requirement in Horsepower. W ˙ f l u i d = m ˙ × w a = ( 120 lb m min ) × ( 25.00 Btu lb m ) = 3 , 000 Btu min \dot{W}_{fluid} = \dot{m} \times w_a = \left(120 \frac{\text{lb}_m}{\text{min}}\right) \times \left(25.00 \frac{\text{Btu}}{\text{lb}_m}\right) = 3,000 \frac{\text{Btu}}{\text{min}} W ˙ f l u i d ​ = m ˙ × w a ​ = ( 120 min lb m ​ ​ ) × ( 25.00 lb m ​ Btu ​ ) = 3 , 000 min Btu ​

Convert Btu/min \text{Btu/min} Btu/min to Horsepower ( 1 HP = 42.418 Btu/min = 2 , 544.4 Btu/hr = 0.7457 kW 1 \text{ HP} = 42.418 \text{ Btu/min} = 2,544.4 \text{ Btu/hr} = 0.7457 \text{ kW} 1 HP = 42.418 Btu/min = 2 , 544.4 Btu/hr = 0.7457 kW ): W ˙ f l u i d , H P = 3 , 000 Btu/min 42.418 Btu/min ⋅ HP = 70.72 HP \dot{W}_{fluid, HP} = \frac{3,000 \text{ Btu/min}}{42.418 \text{ Btu/min}\cdot\text{HP}} = 70.72 \text{ HP} W ˙ f l u i d , H P ​ = 42.418 Btu/min ⋅ HP 3 , 000 Btu/min ​ = 70.72 HP

Accounting for mechanical drive train efficiency ( η m e c h = 0.92 \eta_{mech} = 0.92 η m ec h ​ = 0.92 ): W ˙ b r a k e = W ˙ f l u i d , H P η m e c h = 70.72 HP 0.92 = 76.87 HP ≈ 76.9 HP \dot{W}_{brake} = \frac{\dot{W}_{fluid, HP}}{\eta_{mech}} = \frac{70.72 \text{ HP}}{0.92} = 76.87 \text{ HP} \approx 76.9 \text{ HP} W ˙ b r ak e ​ = η m ec h ​ W ˙ f l u i d , H P ​ ​ = 0.92 70.72 HP ​ = 76.87 HP ≈ 76.9 HP

6. NCEES Reference Handbook Navigation & Exam Traps

Section 1.3: Thermodynamics: Find the general steady-state control volume equation, isentropic efficiency formulas, ideal gas relations, and polytropic work expressions.

Unit Conversion Trap ( P d V P\,dV P d V ): Never multiply psia \text{psia} psia by ft 3 \text{ft}^3 ft 3 without multiplying by 144 in 2 / ft 2 144 \text{ in}^2/\text{ft}^2 144 in 2 / ft 2 . psia × ft 3 ≠ ft ⋅ lb f \text{psia} \times \text{ft}^3 \ne \text{ft}\cdot\text{lb}_f psia × ft 3  = ft ⋅ lb f ​ .

Isentropic Efficiency Inversion: Candidates frequently invert the numerator and denominator. Remember that real compressors always consume more work than ideal ( w a = w s / η c > w s w_a = w_s / \eta_c > w_s w a ​ = w s ​ / η c ​ > w s ​ ), while real turbines always produce less work than ideal ( w a = η t w s < w s w_a = \eta_t w_s < w_s w a ​ = η t ​ w s ​ < w s ​ ). Both efficiencies must be ≤ 1.0 \le 1.0 ≤ 1.0 .

Loading diagram... Steady-Flow Control Volume Energy and Mass Balance