Study guide
2.4 Mass, Energy & Combustion Balances for HVAC Equipment
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
2.4 Mass, Energy & Combustion Balances for HVAC Equipment
Key Takeaways Explain This Topic AI
Hydronic energy balance formulas provide rapid, accurate thermal sizing: water duty is q ˙ = 500 × GPM × Δ T \dot{q} = 500 \times \text{GPM} \times \Delta T q ˙ = 500 × GPM × Δ T (at standard water conditions ρ = 62.4 lb m / ft 3 , c p = 1.0 Btu/lb m ⋅ ∘ F \rho = 62.4 \text{ lb}_m/\text{ft}^3, c_p = 1.0 \text{ Btu/lb}_m\cdot^\circ\text{F} ρ = 62.4 lb m / ft 3 , c p = 1.0 Btu/lb m ⋅ ∘ F ); air sensible duty is q ˙ s = 1.08 × CFM × Δ T \dot{q}_s = 1.08 \times \text{CFM} \times \Delta T q ˙ s = 1.08 × CFM × Δ T .
Cooling tower total heat rejection exceeds evaporator cooling capacity by the compressor heat of compression: q ˙ c o n d = q ˙ e v a p + W ˙ c o m p ≈ 1.20 − 1.25 × q ˙ e v a p \dot{q}_{cond} = \dot{q}_{evap} + \dot{W}_{comp} \approx 1.20 - 1.25 \times \dot{q}_{evap} q ˙ co n d = q ˙ e v a p + W ˙ co m p ≈ 1.20 − 1.25 × q ˙ e v a p ( 15 , 000 Btu/(hr ⋅ ton) 15,000 \text{ Btu/(hr}\cdot\text{ton)} 15 , 000 Btu/(hr ⋅ ton) standard tower rating at 3.0 GPM/ton 3.0 \text{ GPM/ton} 3.0 GPM/ton with a 10 ∘ F 10^\circ\text{F} 1 0 ∘ F range).
Cooling tower water makeup balances evaporation, blowdown, and drift: M = E + B + D M = E + B + D M = E + B + D , where blowdown depends on Cycles of Concentration ( C C C ) via B = E C − 1 B = \frac{E}{C - 1} B = C − 1 E .
Combustion of hydrocarbon fuels produces water vapor; Higher Heating Value (HHV) accounts for latent heat recovery when water vapor condenses, while Lower Heating Value (LHV) assumes water leaves as vapor.
Condensing boilers achieve efficiencies above 90% by reducing flue gas temperatures below the dew point (~ 130 ∘ F 130^\circ\text{F} 13 0 ∘ F for natural gas), capturing the latent heat of condensation.
Last updated: August 2026
2.4 Mass, Energy & Combustion Balances for HVAC Equipment
Practical HVAC design synthesizes mass and energy balances across integrated equipment loops: hydronic water loops, refrigeration refrigerant loops, cooling tower condenser loops, air distribution ducts, and fuel combustion systems. On the PE exam, mastery of rapid conservation equations, cooling tower water balances, and combustion chemistry is essential.
1. Fundamental HVAC Heat Transfer "Shortcut" Equations
In standard design practice, steady-flow energy balances for air and water are simplified by evaluating fluid density ( ρ \rho ρ ) and specific heat ( c p c_p c p ) at standard atmospheric conditions:
Hydronic Water Loops ( 60 ∘ F − 180 ∘ F 60^\circ\text{F} - 180^\circ\text{F} 6 0 ∘ F − 18 0 ∘ F ) q ˙ = m ˙ c p Δ T = ( GPM × 8.33 lb m gal × 60 min hr ) × ( 1.0 Btu lb m ⋅ ∘ F ) × Δ T \dot{q} = \dot{m} c_p \Delta T = \left(\text{GPM} \times 8.33 \frac{\text{lb}_m}{\text{gal}} \times 60 \frac{\text{min}}{\text{hr}}\right) \times \left(1.0 \frac{\text{Btu}}{\text{lb}_m\cdot^\circ\text{F}}\right) \times \Delta T q ˙ = m ˙ c p Δ T = ( GPM × 8.33 gal lb m × 60 hr min ) × ( 1.0 lb m ⋅ ∘ F Btu ) × Δ T q ˙ = 500 × GPM × Δ T ( Btu/hr ) \dot{q} = 500 \times \text{GPM} \times \Delta T \quad (\text{Btu/hr}) q ˙ = 500 × GPM × Δ T ( Btu/hr ) Cooling Tons = 500 × GPM × Δ T 12 , 000 = GPM × Δ T 24 \text{Cooling Tons} = \frac{500 \times \text{GPM} \times \Delta T}{12,000} = \frac{\text{GPM} \times \Delta T}{24} Cooling Tons = 12 , 000 500 × GPM × Δ T = 24 GPM × Δ T
Note: If fluid is an ethylene or propylene glycol mixture, the constant 500 500 500 must be adjusted for specific gravity ( S G SG SG ) and specific heat ( c p c_p c p ): C = 500 × S G × c p C = 500 \times SG \times c_p C = 500 × SG × c p .
Air Distribution Ducts (Standard Air: ρ = 0.075 lb m / ft 3 \rho = 0.075 \text{ lb}_m/\text{ft}^3 ρ = 0.075 lb m / ft 3 , c p = 0.240 Btu/lb m ⋅ ∘ F c_p = 0.240 \text{ Btu/lb}_m\cdot^\circ\text{F} c p = 0.240 Btu/lb m ⋅ ∘ F ) Sensible Heat: q ˙ s = ( CFM × 60 × 0.075 ) × 0.240 × Δ T = 1.08 × CFM × Δ T ( Btu/hr ) \text{Sensible Heat: } \dot{q}_s = \left(\text{CFM} \times 60 \times 0.075\right) \times 0.240 \times \Delta T = 1.08 \times \text{CFM} \times \Delta T \quad (\text{Btu/hr}) Sensible Heat: q ˙ s = ( CFM × 60 × 0.075 ) × 0.240 × Δ T = 1.08 × CFM × Δ T ( Btu/hr ) Latent Heat: q ˙ l = ( CFM × 60 × 0.075 ) × 1 , 061 × Δ W = 4 , 840 × CFM × Δ W ( Btu/hr ) \text{Latent Heat: } \dot{q}_l = \left(\text{CFM} \times 60 \times 0.075\right) \times 1,061 \times \Delta W = 4,840 \times \text{CFM} \times \Delta W \quad (\text{Btu/hr}) Latent Heat: q ˙ l = ( CFM × 60 × 0.075 ) × 1 , 061 × Δ W = 4 , 840 × CFM × Δ W ( Btu/hr ) Total Heat: q ˙ t = ( CFM × 60 × 0.075 ) × Δ h = 4.5 × CFM × Δ h ( Btu/hr ) \text{Total Heat: } \dot{q}_t = \left(\text{CFM} \times 60 \times 0.075\right) \times \Delta h = 4.5 \times \text{CFM} \times \Delta h \quad (\text{Btu/hr}) Total Heat: q ˙ t = ( CFM × 60 × 0.075 ) × Δ h = 4.5 × CFM × Δ h ( Btu/hr )
Where Δ T \Delta T Δ T is dry-bulb temperature difference ( ∘ F ^\circ\text{F} ∘ F ), Δ W \Delta W Δ W is humidity ratio difference ( lb water / lb dry air \text{lb}_{\text{water}}/\text{lb}_{\text{dry air}} lb water / lb dry air ), and Δ h \Delta h Δ h is enthalpy difference ( Btu/lb dry air \text{Btu/lb}_{\text{dry air}} Btu/lb dry air ).
2. Chiller & Cooling Tower Energy Balances
A water chiller acts as an energy combiner: heat absorbed from the building chilled water loop plus the electrical power input to the compressor must be rejected to the condenser water loop. +-------------------------------------------------------------+
- | WATER CHILLER |
- | |
- | [Evaporator] <--- Q_evap = 500 * GPM_chw * Delta_T_chw |
- | | |
- | V |
- | [Compressor] <--- W_comp = 3,412.14 * kW_in |
- | | |
- | V |
- | [Condenser] ---> Q_cond = Q_evap + W_comp |
- +-----------------------------|-------------------------------+
- |
- V
- +-------------------------------------------------------------+
- | COOLING TOWER |
- | |
- | Q_tower = 500 * GPM_cw * (T_cwr - T_cws) = Q_cond |
- | Evaporation: E = Q_tower / h_fg |
- | Makeup: M = E + B + D |
- +-------------------------------------------------------------+
- The "Standard Cooling Tower Ton"
Refrigeration Ton: 1 ton = 12 , 000 Btu/hr 1 \text{ ton} = 12,000 \text{ Btu/hr} 1 ton = 12 , 000 Btu/hr of cooling effect at the evaporator.
Tower Heat Rejection: For electric centrifugal chillers operating at nominal full-load efficiency ( ∼ 0.60 kW/ton \sim 0.60 \text{ kW/ton} ∼ 0.60 kW/ton ), the heat of compression adds 0.60 × 3 , 412.14 ≈ 2 , 047 Btu/hr 0.60 \times 3,412.14 \approx 2,047 \text{ Btu/hr} 0.60 × 3 , 412.14 ≈ 2 , 047 Btu/hr per ton. The total heat rejected is 12 , 000 + 2 , 047 ≈ 14 , 047 Btu/hr 12,000 + 2,047 \approx 14,047 \text{ Btu/hr} 12 , 000 + 2 , 047 ≈ 14 , 047 Btu/hr .
Standard Rating Benchmark: Industry standards (CTI/ASHRAE) rate cooling towers at 15 , 000 Btu/(hr ⋅ ton) 15,000 \text{ Btu/(hr}\cdot\text{ton)} 15 , 000 Btu/(hr ⋅ ton) (a 25 % 25\% 25% heat of compression factor). At standard 3.0 GPM/ton 3.0 \text{ GPM/ton} 3.0 GPM/ton condenser water flow, this corresponds to a 10 ∘ F 10^\circ\text{F} 1 0 ∘ F temperature range ( 85 ∘ F 85^\circ\text{F} 8 5 ∘ F entering, 95 ∘ F 95^\circ\text{F} 9 5 ∘ F leaving): q ˙ t o w e r = 500 × 3.0 GPM × 10 ∘ F = 15 , 000 Btu hr ⋅ ton \dot{q}_{tower} = 500 \times 3.0 \text{ GPM} \times 10^\circ\text{F} = 15,000 \frac{\text{Btu}}{\text{hr}\cdot\text{ton}} q ˙ t o w er = 500 × 3.0 GPM × 1 0 ∘ F = 15 , 000 hr ⋅ ton Btu
3. Cooling Tower Mass & Water Treatment Balances
Evaporative cooling towers reject heat by evaporating water into the ambient airstream. As pure water evaporates, dissolved solids (minerals, calcium, silica) remain behind, concentrating in the sump basin. Water must be intentionally bled off (blowdown) and replaced with fresh city makeup water. Evaporation (E) [Pure H2O Vapor]
- ^
- |
- Makeup (M) -----------> [Cooling Tower Sump] -----------> Blowdown (B) [High TDS]
- [Low TDS] | -----------> Drift (D) [Mist]
- V
- Circulation (GPM_cw)
Conservation of Mass Equations Total Water Mass Balance: M = E + B + D \text{Total Water Mass Balance: } M = E + B + D Total Water Mass Balance: M = E + B + D
Where M M M is makeup rate, E E E is evaporation rate, B B B is blowdown rate, and D D D is drift loss (typically negligible in modern drift eliminators: D < 0.005 % × GPM c i r c D < 0.005\% \times \text{GPM}_{circ} D < 0.005% × GPM c i rc ). Neglecting drift ( D ≈ 0 D \approx 0 D ≈ 0 ): M = E + B M = E + B M = E + B
Dissolved Solids (TDS) Balance & Cycles of Concentration ( C C C ) M × TDS m a k e u p = B × TDS t o w e r M \times \text{TDS}_{makeup} = B \times \text{TDS}_{tower} M × TDS mak e u p = B × TDS t o w er Cycles of Concentration ( C ) = TDS t o w e r TDS m a k e u p = Chlorides t o w e r Chlorides m a k e u p = M B \text{Cycles of Concentration } (C) = \frac{\text{TDS}_{tower}}{\text{TDS}_{makeup}} = \frac{\text{Chlorides}_{tower}}{\text{Chlorides}_{makeup}} = \frac{M}{B} Cycles of Concentration ( C ) = TDS mak e u p TDS t o w er = Chlorides mak e u p Chlorides t o w er = B M
Substituting M = E + B M = E + B M = E + B into the cycles of concentration equation: C = E + B B = E B + 1 ⟹ E B = C − 1 C = \frac{E + B}{B} = \frac{E}{B} + 1 \implies \frac{E}{B} = C - 1 C = B E + B = B E + 1 ⟹ B E = C − 1 Blowdown Flow Rate: B = E C − 1 \text{Blowdown Flow Rate: } B = \frac{E}{C - 1} Blowdown Flow Rate: B = C − 1 E Makeup Flow Rate: M = E × ( C C − 1 ) \text{Makeup Flow Rate: } M = E \times \left(\frac{C}{C - 1}\right) Makeup Flow Rate: M = E × ( C − 1 C )
Evaporation Rate Approximation Formula E = q ˙ t o w e r h f g ≈ q ˙ t o w e r 1 , 050 Btu/lb m E = \frac{\dot{q}_{tower}}{h_{fg}} \approx \frac{\dot{q}_{tower}}{1,050 \text{ Btu/lb}_m} E = h f g q ˙ t o w er ≈ 1 , 050 Btu/lb m q ˙ t o w er
In terms of circulation flow rate and tower temperature range: E ( GPM ) = 0.0008 × GPM c i r c × ( T c w r − T c w s ) = 0.0008 × GPM c i r c × Δ T r a n g e E (\text{GPM}) = 0.0008 \times \text{GPM}_{circ} \times (T_{cwr} - T_{cws}) = 0.0008 \times \text{GPM}_{circ} \times \Delta T_{range} E ( GPM ) = 0.0008 × GPM c i rc × ( T c w r − T c w s ) = 0.0008 × GPM c i rc × Δ T r an g e
4. Combustion Chemistry, Excess Air & Boiler Efficiency
Combustion is the rapid exothermic chemical reaction between fuel hydrocarbons and oxygen in atmospheric air.
Stoichiometric (Theoretical) Combustion of Methane ( CH 4 \text{CH}_4 CH 4 )
Atmospheric air is approximately 21 % O 2 21\% \text{ O}_2 21% O 2 and 79 % N 2 79\% \text{ N}_2 79% N 2 by volume (mole ratio 79 21 = 3.76 moles N 2 / mole O 2 \frac{79}{21} = 3.76 \text{ moles N}_2 / \text{mole O}_2 21 79 = 3.76 moles N 2 / mole O 2 ). CH 4 + 2 ( O 2 + 3.76 N 2 ) ⟶ CO 2 + 2 H 2 O + 7.52 N 2 + Heat \text{CH}_4 + 2 \left(\text{O}_2 + 3.76 \text{ N}_2\right) \longrightarrow \text{CO}_2 + 2 \text{ H}_2\text{O} + 7.52 \text{ N}_2 + \text{Heat} CH 4 + 2 ( O 2 + 3.76 N 2 ) ⟶ CO 2 + 2 H 2 O + 7.52 N 2 + Heat
For 1 mole (or 1 ft 3 1 \text{ ft}^3 1 ft 3 ) of methane gas:
Theoretical O 2 \text{O}_2 O 2 Required: 2.0 moles 2.0 \text{ moles} 2.0 moles
Theoretical Air Required: 2.0 × 4.76 = 9.52 moles 2.0 \times 4.76 = 9.52 \text{ moles} 2.0 × 4.76 = 9.52 moles (or 9.52 ft 3 9.52 \text{ ft}^3 9.52 ft 3 of air per ft 3 \text{ft}^3 ft 3 of CH 4 \text{CH}_4 CH 4 ).
Percent Excess Air
To ensure complete combustion and prevent hazardous carbon monoxide ( CO \text{CO} CO ) and soot generation, commercial boilers operate with excess air ( 10 % 10\% 10% to 25 % 25\% 25% excess air for natural gas): % Excess Air = ( Actual Air − Theoretical Air Theoretical Air ) × 100 % = ( Actual O 2 − Theoretical O 2 Theoretical O 2 ) × 100 % \% \text{ Excess Air} = \left(\frac{\text{Actual Air} - \text{Theoretical Air}}{\text{Theoretical Air}}\right) \times 100\% = \left(\frac{\text{Actual } \text{O}_2 - \text{Theoretical } \text{O}_2}{\text{Theoretical } \text{O}_2}\right) \times 100\% % Excess Air = ( Theoretical Air Actual Air − Theoretical Air ) × 100% = ( Theoretical O 2 Actual O 2 − Theoretical O 2 ) × 100% Theoretical Air-to-Fuel Ratio by Mass: A F m a s s = m a i r m f u e l \text{Theoretical Air-to-Fuel Ratio by Mass: } AF_{mass} = \frac{m_{air}}{m_{fuel}} Theoretical Air-to-Fuel Ratio by Mass: A F ma ss = m f u e l m ai r
Higher Heating Value (HHV) vs. Lower Heating Value (LHV) HHV = LHV + m H 2 O × h f g , H 2 O \text{HHV} = \text{LHV} + m_{H_2O} \times h_{fg,H_2O} HHV = LHV + m H 2 O × h f g , H 2 O
HHV (Gross Calorific Value): Assumes all water vapor formed during combustion is fully condensed back to liquid at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F or 77 ∘ F 77^\circ\text{F} 7 7 ∘ F , releasing its latent heat of condensation ( ∼ 1 , 050 Btu/lb m \sim 1,050 \text{ Btu/lb}_m ∼ 1 , 050 Btu/lb m of water). Natural gas HHV ≈ 1 , 000 − 1 , 050 Btu/ft 3 \approx 1,000 - 1,050 \text{ Btu/ft}^3 ≈ 1 , 000 − 1 , 050 Btu/ft 3 ( ∼ 23 , 800 Btu/lb m \sim 23,800 \text{ Btu/lb}_m ∼ 23 , 800 Btu/lb m ).
LHV (Net Calorific Value): Assumes all water leaves the boiler chimney as vapor, without recovering latent heat. Natural gas LHV ≈ 900 − 950 Btu/ft 3 \approx 900 - 950 \text{ Btu/ft}^3 ≈ 900 − 950 Btu/ft 3 .
- Condensing vs. Non-Condensing Boiler Mechanics Thermal Efficiency (%)
- 100% +--------------------------------------------/ (Latent Heat Recovery Zone)
- | /
- 95% +------------------------------------------/ Condensing Boilers
- | / (Eff = 90% - 98%)
- 90% +----------------------------------------/
- | Flue Gas Dew Point (~130°F)
- 85% +---------------------+------------------ (Sensible-Only Cooling Zone)
- | / Non-Condensing Boilers (Eff = 80% - 85%)
- 80% +-------------------/--------------------
- +-------------------+--------------------+------> Water Return Temperature (°F)
- 130°F 180°F
Non-Condensing Boilers: Designed with minimum return water temperature > 140 ∘ F >140^\circ\text{F} > 14 0 ∘ F to keep flue gas temperature above the acid dew point ( ∼ 130 ∘ F \sim 130^\circ\text{F} ∼ 13 0 ∘ F ), preventing corrosive condensate from degrading steel/cast-iron heat exchangers. Peak thermal efficiency is limited to 80 % − 85 % 80\% - 85\% 80% − 85% .
Condensing Boilers: Constructed from 316L stainless steel or cast aluminum to resist acidic condensate ( pH 3.0 − 5.0 \text{pH } 3.0 - 5.0 pH 3.0 − 5.0 ). When return water is below 120 ∘ F 120^\circ\text{F} 12 0 ∘ F (ideally 80 ∘ F − 100 ∘ F 80^\circ\text{F} - 100^\circ\text{F} 8 0 ∘ F − 10 0 ∘ F ), flue gas water vapor condenses, boosting overall thermal efficiency to 92 % − 98 % 92\% - 98\% 92% − 98% .
5. Worked Example: Comprehensive Cooling Tower Makeup & Blowdown Analysis
Problem: A campus central plant operates a 1 , 500 -ton 1,500 \text{-ton} 1 , 500 -ton water-cooled centrifugal chiller operating at full load with an efficiency of 0.56 kW/ton 0.56 \text{ kW/ton} 0.56 kW/ton . The condenser water is circulated through an induced-draft cooling tower at 3.0 GPM/ton 3.0 \text{ GPM/ton} 3.0 GPM/ton entering the tower at 95.0 ∘ F 95.0^\circ\text{F} 95. 0 ∘ F and leaving at 85.0 ∘ F 85.0^\circ\text{F} 85. 0 ∘ F . Water analysis reveals that city makeup water contains 120 ppm 120 \text{ ppm} 120 ppm of total dissolved solids (TDS), while the cooling tower water chemistry must be maintained at a maximum of 600 ppm 600 \text{ ppm} 600 ppm TDS to prevent calcium carbonate scaling. Assume latent heat of vaporization h f g = 1 , 050 Btu/lb m h_{fg} = 1,050 \text{ Btu/lb}_m h f g = 1 , 050 Btu/lb m and drift loss is negligible.
Find:
The total heat rejection rate ( Q ˙ t o w e r \dot{Q}_{tower} Q ˙ t o w er ) to the cooling tower in Btu/hr \text{Btu/hr} Btu/hr .
The evaporation rate ( E E E ) in GPM \text{GPM} GPM .
The Cycles of Concentration ( C C C ).
The required continuous blowdown rate ( B B B ) and makeup water rate ( M M M ) in GPM \text{GPM} GPM .
Step-by-Step Solution:
Step 1: Calculate total condenser heat rejection rate Q ˙ t o w e r \dot{Q}_{tower} Q ˙ t o w er . Q ˙ e v a p = 1 , 500 tons × 12 , 000 Btu hr ⋅ ton = 18 , 000 , 000 Btu hr \dot{Q}_{evap} = 1,500 \text{ tons} \times 12,000 \frac{\text{Btu}}{\text{hr}\cdot\text{ton}} = 18,000,000 \frac{\text{Btu}}{\text{hr}} Q ˙ e v a p = 1 , 500 tons × 12 , 000 hr ⋅ ton Btu = 18 , 000 , 000 hr Btu W ˙ c o m p = 1 , 500 tons × 0.56 kW ton × 3 , 412.14 Btu hr ⋅ kW = 840.0 kW × 3 , 412.14 = 2 , 866 , 198 Btu hr \dot{W}_{comp} = 1,500 \text{ tons} \times 0.56 \frac{\text{kW}}{\text{ton}} \times 3,412.14 \frac{\text{Btu}}{\text{hr}\cdot\text{kW}} = 840.0 \text{ kW} \times 3,412.14 = 2,866,198 \frac{\text{Btu}}{\text{hr}} W ˙ co m p = 1 , 500 tons × 0.56 ton kW × 3 , 412.14 hr ⋅ kW Btu = 840.0 kW × 3 , 412.14 = 2 , 866 , 198 hr Btu Q ˙ t o w e r = Q ˙ e v a p + W ˙ c o m p = 18 , 000 , 000 + 2 , 866 , 198 = 20 , 866 , 198 Btu hr \dot{Q}_{tower} = \dot{Q}_{evap} + \dot{W}_{comp} = 18,000,000 + 2,866,198 = 20,866,198 \frac{\text{Btu}}{\text{hr}} Q ˙ t o w er = Q ˙ e v a p + W ˙ co m p = 18 , 000 , 000 + 2 , 866 , 198 = 20 , 866 , 198 hr Btu
(Check via water loop: GPM c w = 1 , 500 × 3.0 = 4 , 500 GPM \text{GPM}_{cw} = 1,500 \times 3.0 = 4,500 \text{ GPM} GPM c w = 1 , 500 × 3.0 = 4 , 500 GPM . Q ˙ = 500 × 4 , 500 × ( 95 − 85 ) = 22 , 500 , 000 Btu/hr \dot{Q} = 500 \times 4,500 \times (95 - 85) = 22,500,000 \text{ Btu/hr} Q ˙ = 500 × 4 , 500 × ( 95 − 85 ) = 22 , 500 , 000 Btu/hr at standard 10 ∘ F 10^\circ\text{F} 1 0 ∘ F tower rating). Use the exact heat rejection of 20 , 866 , 198 Btu/hr 20,866,198 \text{ Btu/hr} 20 , 866 , 198 Btu/hr for evaporation calculation.
Step 2: Calculate evaporation rate ( E E E ). E = Q ˙ t o w e r h f g × ρ w a t e r = 20 , 866 , 198 Btu/hr 1 , 050 Btu/lb m × 8.33 lb m / gal × 60 min / hr E = \frac{\dot{Q}_{tower}}{h_{fg} \times \rho_{water}} = \frac{20,866,198 \text{ Btu/hr}}{1,050 \text{ Btu/lb}_m \times 8.33 \text{ lb}_m/\text{gal} \times 60 \text{ min}/\text{hr}} E = h f g × ρ w a t er Q ˙ t o w er = 1 , 050 Btu/lb m × 8.33 lb m / gal × 60 min / hr 20 , 866 , 198 Btu/hr E = 20 , 866 , 198 524 , 790 = 39.76 GPM E = \frac{20,866,198}{524,790} = 39.76 \text{ GPM} E = 524 , 790 20 , 866 , 198 = 39.76 GPM
(Check via rule-of-thumb: E = 0.0008 × 4 , 500 GPM × 10 = 36.0 GPM E = 0.0008 \times 4,500 \text{ GPM} \times 10 = 36.0 \text{ GPM} E = 0.0008 × 4 , 500 GPM × 10 = 36.0 GPM using nominal cooling). Using exact thermodynamic duty: E = 39.8 GPM E = 39.8 \text{ GPM} E = 39.8 GPM .
Step 3: Calculate Cycles of Concentration ( C C C ). C = TDS t o w e r TDS m a k e u p = 600 ppm 120 ppm = 5.0 C = \frac{\text{TDS}_{tower}}{\text{TDS}_{makeup}} = \frac{600 \text{ ppm}}{120 \text{ ppm}} = 5.0 C = TDS mak e u p TDS t o w er = 120 ppm 600 ppm = 5.0
Step 4: Calculate Blowdown rate ( B B B ) and Makeup rate ( M M M ). B = E C − 1 = 39.76 GPM 5.0 − 1 = 39.76 4 = 9.94 GPM B = \frac{E}{C - 1} = \frac{39.76 \text{ GPM}}{5.0 - 1} = \frac{39.76}{4} = 9.94 \text{ GPM} B = C − 1 E = 5.0 − 1 39.76 GPM = 4 39.76 = 9.94 GPM M = E + B = 39.76 + 9.94 = 49.70 GPM M = E + B = 39.76 + 9.94 = 49.70 \text{ GPM} M = E + B = 39.76 + 9.94 = 49.70 GPM
(Check: M = E × C C − 1 = 39.76 × 5 4 = 49.70 GPM M = E \times \frac{C}{C - 1} = 39.76 \times \frac{5}{4} = 49.70 \text{ GPM} M = E × C − 1 C = 39.76 × 4 5 = 49.70 GPM ).
6. NCEES Reference Handbook Navigation & Exam Traps
Section 1.3 & 1.4: Combustion & Heat Transfer: Review stoichiometric air-fuel tables, heating values, and cooling tower definitions.
Tower Ton Confusion: Remember that an evaporative cooling tower ton is nominally rated at 15 , 000 Btu/hr 15,000 \text{ Btu/hr} 15 , 000 Btu/hr , not 12 , 000 Btu/hr 12,000 \text{ Btu/hr} 12 , 000 Btu/hr , because it must reject both the building evaporator load and the compressor power.
Cycles of Concentration Denominator: The blowdown formula is B = E C − 1 B = \frac{E}{C - 1} B = C − 1 E . Do not divide by C C C ; dividing by C C C rather than C − 1 C-1 C − 1 is a standard NCEES exam distractor trap!