Study guide
2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit
PE Mechanical: HVAC and Refrigeration Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Engineering Foundations
1.1 NCEES Exam Specification, CBT Delivery & Reference Handbook Strategy 1.2 Engineering Units, Dimensional Analysis & Physical Property Lookups 1.3 Engineering Economics, Life Cycle Cost Analysis & Equipment Financial Evaluation 1.4 Electrical Foundations, Motor Ratings & Variable Frequency Drives (VFDs)
2 Chapter 2: Thermodynamics & Energy Balances
2.1 First and Second Laws of Thermodynamics & Open/Closed System Energy Balances 2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit 2.3 Gas & Vapor Property Evaluation: Steam Tables, Superheat & Subcooling 2.4 Mass, Energy & Combustion Balances for HVAC Equipment
3 Chapter 3: Psychrometrics, Moist Air Processes & Humidity Equipment
3.1 Psychrometric Properties: DBT, WBT, DPT, RH, Humidity Ratio & Enthalpy 3.2 Chart Reading & Psychrometric Equations at Sea Level vs. Altitude (5,000 ft) 3.3 Basic Psychrometric Processes: Sensible Heating/Cooling, Humidification & Dehumidification 3.4 Mixed Air Calculations & Complex Air Conditioning Cycles (Preheat, Reheat & Bypass) 3.5 Sensible Heat Ratio (SHR), Apparatus Dew Point (ADP) & Coil Bypass Factor 3.6 Humidification & Dehumidification Equipment: Steam, Adiabatic, Desiccant & Low-Temperature Processes
4 Chapter 4: Heat Transfer Principles & Sizing
4.1 Steady-State Conduction & Multilayer Thermal Resistance (R-Value & U-Factor) 4.2 Convective Heat Transfer & Forced/Natural Convection Coefficients 4.3 Radiation Heat Transfer, Surface Emissivity & View Factors 4.4 Overall Heat Transfer Coefficients, Fouling Factors & Transient/Thermal Mass Effects 4.5 Heat Exchanger Analysis: Log Mean Temperature Difference (LMTD) & Effectiveness-NTU (ε-NTU)
5 Chapter 5: Fluid Mechanics & Hydraulic Fundamentals
5.1 Fluid Statics, Incompressible Continuity & Bernoulli Energy Equation 5.2 Pipe Friction, Moody Diagram & Darcy-Weisbach / Hazen-Williams Calculations 5.3 Minor Losses: Equivalent Length, Loss Coefficients (K-factors) & Total System Head 5.4 Pump Sizing, Net Positive Suction Head (NPSHa vs NPSHr) & Cavitation Prevention 5.5 Affinity Laws & Parallel/Series Pump/Fan System Curves
6 Chapter 6: Heating & Cooling Load Calculations
6.1 Outdoor & Indoor Design Conditions (ASHRAE Fundamentals, Climatic Data & Indoor Setpoints) 6.2 Envelope Heat Transmission & Infiltration/Exfiltration Load Methods 6.3 Solar Heat Gain (SHGC), Fenestration & Cooling Load Temperature Difference / Radiant Time Series (CLTD/RTS) 6.4 Internal Heat Gains: Lighting, People, Equipment & Diversity Factors 6.5 Ventilation Loads & Sensible / Latent / Total Cooling Load Synthesis
7 Chapter 7: Refrigeration Principles, Cycles & Cold Storage Applications
7.1 Standard Vapor-Compression Refrigeration Cycle on P-h & T-s Diagrams 7.2 Refrigeration Cycle Performance Metrics: COP, EER, SEER, kW/ton & Ton of Refrigeration 7.3 Cycle Enhancements: Subcooling, Superheating, Liquid-Suction Heat Exchangers & Economizers 7.4 Multi-Stage & Cascade Refrigeration Systems: Intercooling & Flash Gas Removal 7.5 Absorption Refrigeration Cycles: Water-Lithium Bromide & Ammonia-Water Systems 7.6 Food Processing & Cold Storage Refrigeration: Product Load, Pull-Down & Storage Design
8 Chapter 8: Refrigerants, Environmental Regulations & Safety
8.1 Refrigerant Classifications, Nomenclature & Thermodynamic Properties (ASHRAE Standard 34) 8.2 AIM Act, EPA Technology Transitions Sector GWP Limits & Low-GWP Refrigerants (R-32, R-454B) 8.3 Refrigerant Safety Requirements & Machinery Room Design (ASHRAE Standard 15) 8.4 Refrigerant Piping Sizing, Oil Return, Traps & Double Risers
9 Chapter 9: HVAC Equipment & Primary Machinery
9.1 Compressors: Reciprocating, Rotary, Scroll, Screw & Centrifugal 9.2 Condensers: Air-Cooled, Water-Cooled & Evaporative Condensers 9.3 Evaporators & Direct Expansion (DX) vs Liquid Chilling Coils 9.4 Water Chillers: Centrifugal, Screw & Scroll with ASHRAE 90.1 Path A/B IPLV Ratings 9.5 Cooling Towers: Range, Approach, Evaporation, Blowdown & Legionella Control 9.6 Heat Pumps & Variable Refrigerant Flow (VRF): Balance Point, Defrost & Heat Recovery 9.7 Thermal Energy Storage: Full vs. Partial Storage, Chilled Water & Ice Systems
10 Chapter 10: Air-Side Systems & Distribution
10.1 Air Handling Units (AHUs), Dedicated Outdoor Air Systems (DOAS) & Fan-Coil Units 10.2 Duct Design Methodologies: Equal Friction, Static Regain & Velocity Reduction 10.3 Duct Fittings, Dynamic Pressure Losses & SMACNA Construction Standards 10.4 Fan Types, Performance Curves, System Effect Factors & Surge/Stall Dynamics 10.5 Variable Air Volume (VAV) Systems, Terminal Boxes & Space Air Diffusion (ADPI) 10.6 Cooling & Heating Coil Selection: Face Velocity, Rows, Circuiting & Freeze Protection
11 Chapter 11: Hydronic, Steam & Fuel Distribution and Heating Plant
11.1 Hydronic System Architectures: Primary-Only, Primary-Secondary & Variable Primary Flow (VPF) 11.2 Hydronic Pipe Sizing, Velocity Limits & Closed/Open Expansion Tank Sizing 11.3 Control Valves: 2-Way vs 3-Way, Valve Authority (N), Cv Calculations & Characteristic Curves 11.4 Boilers & Heating Hot Water Systems: Condensing vs Non-Condensing & Water Treatment 11.5 Furnaces & Gas-Fired Heating Equipment: AFUE, Temperature Rise, Combustion Air & Vent Categories 11.6 Steam & Condensate Distribution: Latent Heat, Trap Selection, Flash Steam & Stall 11.7 Fuel Gas & Fuel Oil Piping: Demand, Sizing Method, Pressure Drop & Storage Systems
12 Chapter 12: HVAC Control Concepts, Sensors & Sequences
12.1 Sensors, Actuators & Dampers: Selection, Placement, Fail-Safe Position & Damper Authority 12.2 Control Loops: Proportional Offset, PID Action, Reset Strategies & Standard Sequences
13 Chapter 13: Building Energy, Ventilation & Indoor Environmental Quality Codes
13.1 ASHRAE Standard 62.1: Ventilation Rate Procedure (VRP), Indoor Air Quality Procedure & DCV 13.2 ASHRAE Standard 90.1: Building Energy Envelope, Mechanical Efficiency & Economizer Mandates 13.3 ASHRAE Standard 55: Thermal Environmental Conditions, PMV/PPD & Adaptive Comfort Models 13.4 Energy Recovery Systems: Enthalpy Wheels, Fixed-Plate Exchangers, Heat Pipes & Runaround Loops
14 Chapter 14: Supportive Engineering Knowledge, Life Safety & Operations
14.1 Air Filtration Standards: MERV Ratings (ASHRAE 52.2), HEPA & Gas-Phase Adsorption 14.2 Life Safety Systems: Fire/Smoke Dampers, Stairwell Pressurization (NFPA 92) & Smoke Control (NFPA 90A) 14.3 Acoustical Control & Vibration Isolation in HVAC Systems (NC / RC Criteria)
2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit
Key Takeaways Explain This Topic AI
The Carnot cycle establishes the absolute upper thermodynamic efficiency limit for any heat engine operating between two thermal reservoirs: η t h , C a r n o t = 1 − T L T H \eta_{th, Carnot} = 1 - \frac{T_L}{T_H} η t h , C a r n o t = 1 − T H T L with temperatures strictly in absolute degrees (Kelvin or Rankine).
The Reversed Carnot cycle defines the theoretical maximum Coefficient of Performance (COP) for refrigeration ( COP R , C a r n o t = T L T H − T L \text{COP}_{R, Carnot} = \frac{T_L}{T_H - T_L} COP R , C a r n o t = T H − T L T L ) and heat pumps ( COP H P , C a r n o t = T H T H − T L = COP R , C a r n o t + 1 \text{COP}_{HP, Carnot} = \frac{T_H}{T_H - T_L} = \text{COP}_{R, Carnot} + 1 COP H P , C a r n o t = T H − T L T H = COP R , C a r n o t + 1 ).
Second Law efficiency ( η I I = COP a c t u a l COP C a r n o t \eta_{II} = \frac{\text{COP}_{actual}}{\text{COP}_{Carnot}} η II = COP C a r n o t COP a c t u a l ) benchmarks real equipment against the reversible limit; modern centrifugal chillers typically achieve η I I \eta_{II} η II between 55% and 75%.
The ideal Rankine cycle models steam power and district energy cogeneration plants using pump compression, boiler vaporization, turbine expansion, and condenser heat rejection; net work is w n e t = ( h 1 − h 2 ) − v f ( P b − P c ) w_{net} = (h_1 - h_2) - v_f (P_b - P_c) w n e t = ( h 1 − h 2 ) − v f ( P b − P c ) .
The Brayton cycle models gas turbines in combined cooling, heating, and power (CCHP) systems; its thermal efficiency is governed by the pressure ratio r p = P 2 P 1 r_p = \frac{P_2}{P_1} r p = P 1 P 2 via η t h , B r a y t o n = 1 − 1 r p ( k − 1 ) / k \eta_{th, Brayton} = 1 - \frac{1}{r_p^{(k-1)/k}} η t h , B r a y t o n = 1 − r p ( k − 1 ) / k 1 .
Last updated: August 2026
2.2 Thermodynamic Cycles: Carnot, Rankine, Brayton & Reversed Carnot Limit
Thermodynamic cycles describe the continuous sequence of processes that convert thermal energy into mechanical power (heat engines) or utilize mechanical power to transfer heat from low to high temperature reservoirs (refrigerators and heat pumps). On the PE Mechanical HVAC exam, mastery of cycle benchmarks allows engineers to evaluate plant performance, verify equipment claims, and size combined heat and power (CHP) systems.
1. The Carnot Cycle & Theoretical Thermal Limits
Proposed by Nicolas Léonard Sadi Carnot in 1824, the Carnot Cycle is a totally reversible ideal cycle operating between a high-temperature source at T H T_H T H and a low-temperature sink at T L T_L T L . It consists of four internally and externally reversible processes:
1 to 2: Reversible Isothermal Heat Addition at T H T_H T H ( q i n = T H ( s 2 − s 1 ) q_{in} = T_H (s_2 - s_1) q in = T H ( s 2 − s 1 ) ).
2 to 3: Isentropic (Reversible Adiabatic) Expansion from T H T_H T H to T L T_L T L ( s 2 = s 3 s_2 = s_3 s 2 = s 3 ).
3 to 4: Reversible Isothermal Heat Rejection at T L T_L T L ( q o u t = T L ( s 3 − s 4 ) = T L ( s 2 − s 1 ) q_{out} = T_L (s_3 - s_4) = T_L (s_2 - s_1) q o u t = T L ( s 3 − s 4 ) = T L ( s 2 − s 1 ) ).
4 to 1: Isentropic (Reversible Adiabatic) Compression from T L T_L T L to T H T_H T H ( s 4 = s 1 s_4 = s_1 s 4 = s 1 ). Temperature (T)
- ^
- TH +--------1==============2-------- (Isothermal Heat Addition, q_in = TH*Delta_s)
- | | |
- | | (Isentropic) | (Isentropic Expansion)
- | | |
- TL +--------4==============3-------- (Isothermal Heat Rejection, q_out = TL*Delta_s)
- | | |
- +--------+--------------+--------> Entropy (s)
- s1=s4 s2=s3
Carnot Heat Engine Efficiency η t h = W n e t , o u t Q i n = Q H − Q L Q H = 1 − Q L Q H \eta_{th} = \frac{W_{net,out}}{Q_{in}} = \frac{Q_H - Q_L}{Q_H} = 1 - \frac{Q_L}{Q_H} η t h = Q in W n e t , o u t = Q H Q H − Q L = 1 − Q H Q L
Because the cycle is totally reversible, Q L Q H = T L T H \frac{Q_L}{Q_H} = \frac{T_L}{T_H} Q H Q L = T H T L (where T L T_L T L and T H T_H T H are in absolute temperature: ∘ R = ∘ F + 459.67 ^\circ\text{R} = ^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 or K = ∘ C + 273.15 \text{K} = ^\circ\text{C} + 273.15 K = ∘ C + 273.15 ): η t h , C a r n o t = 1 − T L T H \eta_{th, Carnot} = 1 - \frac{T_L}{T_H} η t h , C a r n o t = 1 − T H T L
Carnot Principles:
The efficiency of an irreversible heat engine is always less than the efficiency of a reversible heat engine operating between the same two reservoirs ( η a c t u a l < η C a r n o t \eta_{actual} < \eta_{Carnot} η a c t u a l < η C a r n o t ).
The efficiencies of all reversible heat engines operating between the same two reservoirs are identical, regardless of the working fluid.
2. The Reversed Carnot Cycle: Refrigeration & Heat Pump Limits
Running the Carnot cycle in reverse (counter-clockwise on P − v P-v P − v and T − s T-s T − s diagrams) produces the theoretical benchmark for all vapor-compression and absorption refrigeration systems.
Coefficients of Performance (COP) Refrigeration Mode: COP R , C a r n o t = Desired Output Required Work Input = Q L W n e t , i n = Q L Q H − Q L = T L T H − T L \text{Refrigeration Mode: } \text{COP}_{R, Carnot} = \frac{\text{Desired Output}}{\text{Required Work Input}} = \frac{Q_L}{W_{net,in}} = \frac{Q_L}{Q_H - Q_L} = \frac{T_L}{T_H - T_L} Refrigeration Mode: COP R , C a r n o t = Required Work Input Desired Output = W n e t , in Q L = Q H − Q L Q L = T H − T L T L Heat Pump Mode: COP H P , C a r n o t = Desired Output Required Work Input = Q H W n e t , i n = Q H Q H − Q L = T H T H − T L \text{Heat Pump Mode: } \text{COP}_{HP, Carnot} = \frac{\text{Desired Output}}{\text{Required Work Input}} = \frac{Q_H}{W_{net,in}} = \frac{Q_H}{Q_H - Q_L} = \frac{T_H}{T_H - T_L} Heat Pump Mode: COP H P , C a r n o t = Required Work Input Desired Output = W n e t , in Q H = Q H − Q L Q H = T H − T L T H
Notice the fundamental thermodynamic relationship between heat pump and refrigeration COPs: COP H P = COP R + 1 \text{COP}_{HP} = \text{COP}_R + 1 COP H P = COP R + 1
Converting Between HVAC Performance Metrics
On the PE exam, equipment ratings are expressed in diverse imperial and metric units: kW/ton = 12 kBtu/ton × 0.293071 kW/kBtu COP R × 1.0 = 3.51685 COP R \text{kW/ton} = \frac{12 \text{ kBtu/ton} \times 0.293071 \text{ kW/kBtu}}{\text{COP}_R \times 1.0} = \frac{3.51685}{\text{COP}_R} kW/ton = COP R × 1.0 12 kBtu/ton × 0.293071 kW/kBtu = COP R 3.51685 EER (Btu/W ⋅ hr) = 3.41214 × COP R = 12 kW/ton \text{EER (Btu/W}\cdot\text{hr)} = 3.41214 \times \text{COP}_R = \frac{12}{\text{kW/ton}} EER (Btu/W ⋅ hr) = 3.41214 × COP R = kW/ton 12
Second Law (Exergy) Efficiency
The Second Law efficiency ( η I I \eta_{II} η II ) measures how close an actual refrigeration machine approaches the theoretical Carnot ceiling under identical reservoir temperatures: η I I = COP a c t u a l COP C a r n o t = kW/ton C a r n o t kW/ton a c t u a l \eta_{II} = \frac{\text{COP}_{actual}}{\text{COP}_{Carnot}} = \frac{\text{kW/ton}_{Carnot}}{\text{kW/ton}_{actual}} η II = COP C a r n o t COP a c t u a l = kW/ton a c t u a l kW/ton C a r n o t
Modern high-efficiency water-cooled centrifugal chillers typically exhibit η I I ≈ 0.60 − 0.75 \eta_{II} \approx 0.60 - 0.75 η II ≈ 0.60 − 0.75 , while small direct-expansion (DX) rooftop split systems achieve η I I ≈ 0.35 − 0.50 \eta_{II} \approx 0.35 - 0.50 η II ≈ 0.35 − 0.50 .
3. The Rankine Cycle (Steam Power & District Energy Cogeneration)
The Rankine cycle is the fundamental operating cycle for steam-based power plants and large campus district energy facilities producing steam for district heating, absorption chillers, and turbine drives. [Boiler / Steam Generator] <==== (Qin)
- ^ |
- (4) | Liquid | Superheated Steam (1)
- [Feed Pump] V
- (Win)| [Steam Turbine] ====> (Wout)
- | Liquid |
- | | Wet / Low-Pressure Vapor (2)
- [Condenser] <===========+
- =====> (Qout to Cooling Tower)
- State 3: Saturated Liquid
- Ideal Rankine Cycle State Points & Energy Equations
1 to 2: Isentropic Expansion in Turbine: Steam expands from boiler pressure ( P h i g h P_{high} P hi g h ) to condenser pressure ( P l o w P_{low} P l o w ). Shaft work output is: w t = h 1 − h 2 = η t ( h 1 − h 2 s ) w_{t} = h_1 - h_2 = \eta_t (h_1 - h_{2s}) w t = h 1 − h 2 = η t ( h 1 − h 2 s )
2 to 3: Constant-Pressure Heat Rejection in Condenser: Steam condenses to saturated liquid at P l o w P_{low} P l o w ( T 3 = T s a t ( P l o w ) T_3 = T_{sat}(P_{low}) T 3 = T s a t ( P l o w ) , h 3 = h f @ P l o w h_3 = h_{f@P_{low}} h 3 = h f @ P l o w ): q o u t = h 2 − h 3 q_{out} = h_2 - h_3 q o u t = h 2 − h 3
3 to 4: Isentropic Pumping of Liquid Feedwater: Saturated liquid is pumped from P l o w P_{low} P l o w to P h i g h P_{high} P hi g h . Because liquid is virtually incompressible ( v ≈ v f @ P l o w = constant v \approx v_{f@P_{low}} = \text{constant} v ≈ v f @ P l o w = constant ): w p , i n = h 4 − h 3 = ∫ 3 4 v d P ≈ v 3 ( P 4 − P 3 ) = v f @ P 3 ( P b o i l e r − P c o n d e n s e r ) w_{p,in} = h_4 - h_3 = \int_3^4 v\,dP \approx v_3 (P_4 - P_3) = v_{f@P_3} (P_{boiler} - P_{condenser}) w p , in = h 4 − h 3 = ∫ 3 4 v d P ≈ v 3 ( P 4 − P 3 ) = v f @ P 3 ( P b o i l er − P co n d e n ser ) h 4 = h 3 + w p , i n = h 3 + v 3 ( P b o i l e r − P c o n d e n s e r ) η p h_4 = h_3 + w_{p,in} = h_3 + \frac{v_3 (P_{boiler} - P_{condenser})}{\eta_p} h 4 = h 3 + w p , in = h 3 + η p v 3 ( P b o i l er − P co n d e n ser )
4 to 1: Constant-Pressure Heat Addition in Boiler: Water enters as subcooled liquid, is heated to saturation, evaporated, and superheated to T 1 T_1 T 1 : q i n = h 1 − h 4 q_{in} = h_1 - h_4 q in = h 1 − h 4
Thermal Efficiency of the Rankine Cycle η t h , R a n k i n e = w n e t , o u t q i n = w t − w p q i n = ( h 1 − h 2 ) − ( h 4 − h 3 ) h 1 − h 4 \eta_{th, Rankine} = \frac{w_{net,out}}{q_{in}} = \frac{w_t - w_p}{q_{in}} = \frac{(h_1 - h_2) - (h_4 - h_3)}{h_1 - h_4} η t h , R ankin e = q in w n e t , o u t = q in w t − w p = h 1 − h 4 ( h 1 − h 2 ) − ( h 4 − h 3 )
Combined Heat & Power (CHP) / Cogeneration Utilization Factor
In district energy plants, high-pressure steam drives a backpressure extraction turbine, and low-pressure exhaust steam is delivered to building heating coils and domestic water heat exchangers: ϵ C H P = W ˙ n e t + Q ˙ p r o c e s s Q ˙ i n \epsilon_{CHP} = \frac{\dot{W}_{net} + \dot{Q}_{process}}{\dot{Q}_{in}} ϵ C H P = Q ˙ in W ˙ n e t + Q ˙ p rocess
4. The Brayton Cycle (Gas Turbines in CCHP Plants)
The Brayton Cycle is the ideal air-standard cycle for gas turbine power plants, frequently deployed in industrial HVAC plants for Combined Cooling, Heating, and Power (CCHP) with waste-heat-driven absorption chillers.
Ideal Air-Standard Brayton Cycle Processes
1 to 2: Isentropic Compression in a compressor ( P 1 → P 2 P_1 \to P_2 P 1 → P 2 ).
2 to 3: Constant-Pressure Combustion / Heat Addition ( q i n = c p ( T 3 − T 2 ) q_{in} = c_p (T_3 - T_2) q in = c p ( T 3 − T 2 ) ).
3 to 4: Isentropic Expansion through a gas turbine ( P 2 → P 1 P_2 \to P_1 P 2 → P 1 , w t = c p ( T 3 − T 4 ) w_t = c_p (T_3 - T_4) w t = c p ( T 3 − T 4 ) ).
4 to 1: Constant-Pressure Heat Rejection ( q o u t = c p ( T 4 − T 1 ) q_{out} = c_p (T_4 - T_1) q o u t = c p ( T 4 − T 1 ) ).
Brayton Thermal Efficiency & Pressure Ratio
Defining the pressure ratio r p = P 2 P 1 r_p = \frac{P_2}{P_1} r p = P 1 P 2 : T 2 T 1 = ( P 2 P 1 ) k − 1 k = r p k − 1 k = T 3 T 4 \frac{T_2}{T_1} = \left(\frac{P_2}{P_1}\right)^{\frac{k-1}{k}} = r_p^{\frac{k-1}{k}} = \frac{T_3}{T_4} T 1 T 2 = ( P 1 P 2 ) k k − 1 = r p k k − 1 = T 4 T 3 η t h , B r a y t o n = 1 − q o u t q i n = 1 − c p ( T 4 − T 1 ) c p ( T 3 − T 2 ) = 1 − 1 r p k − 1 k \eta_{th, Brayton} = 1 - \frac{q_{out}}{q_{in}} = 1 - \frac{c_p (T_4 - T_1)}{c_p (T_3 - T_2)} = 1 - \frac{1}{r_p^{\frac{k-1}{k}}} η t h , B r a y t o n = 1 − q in q o u t = 1 − c p ( T 3 − T 2 ) c p ( T 4 − T 1 ) = 1 − r p k k − 1 1
Back Work Ratio (BWR)
Gas turbines differ fundamentally from steam Rankine cycles in their Back Work Ratio (BWR) . Because the compressor compresses a low-density gas rather than an incompressible liquid, compression consumes 40% to 60% of the gross turbine work: BWR = w c o m p , i n w t u r b , o u t = h 2 − h 1 h 3 − h 4 = c p ( T 2 − T 1 ) c p ( T 3 − T 4 ) \text{BWR} = \frac{w_{comp,in}}{w_{turb,out}} = \frac{h_2 - h_1}{h_3 - h_4} = \frac{c_p (T_2 - T_1)}{c_p (T_3 - T_4)} BWR = w t u r b , o u t w co m p , in = h 3 − h 4 h 2 − h 1 = c p ( T 3 − T 4 ) c p ( T 2 − T 1 )
In contrast, a Rankine cycle feed pump typically consumes less than 1% to 2% of the steam turbine output ( B W R R a n k i n e < 0.02 BWR_{Rankine} < 0.02 B W R R ankin e < 0.02 ).
5. Summary Comparison of Fundamental Thermodynamic Cycles
Cycle Working Fluid Typical Working Pressure / Temp Primary Application in Building Systems Ideal Thermal Limit Expression
Carnot Engine Conceptual Any T H , T L T_H, T_L T H , T L Theoretical ceiling for all heat engines η t h = 1 − T L T H \eta_{th} = 1 - \frac{T_L}{T_H} η t h = 1 − T H T L
Reversed Carnot Refrigerants / Air Evaporator T L T_L T L , Condenser T H T_H T H Theoretical ceiling for DX chillers and heat pumps COP R = T L T H − T L \text{COP}_R = \frac{T_L}{T_H - T_L} COP R = T H − T L T L
Rankine Cycle Water / Steam 15–1,200 psig, saturated to superheated Central boiler plants, district steam, turbine-driven chillers η t h = ( h 1 − h 2 ) − v f Δ P h 1 − h 4 \eta_{th} = \frac{(h_1 - h_2) - v_f \Delta P}{h_1 - h_4} η t h = h 1 − h 4 ( h 1 − h 2 ) − v f Δ P
Brayton Cycle Air / Combustion gases Pressure ratio r p ≈ 8 − 25 r_p \approx 8 - 25 r p ≈ 8 − 25 , T i n ≈ 1 , 800 − 2 , 500 ∘ F T_{in} \approx 1,800-2,500^\circ\text{F} T in ≈ 1 , 800 − 2 , 50 0 ∘ F Gas turbine cogeneration, microturbines driving CCHP η t h = 1 − 1 r p ( k − 1 ) / k \eta_{th} = 1 - \frac{1}{r_p^{(k-1)/k}} η t h = 1 − r p ( k − 1 ) / k 1
6. Worked Example: Second Law Benchmarking of a Water-Cooled Chiller
Problem: A central plant water-cooled centrifugal chiller produces 600 tons 600 \text{ tons} 600 tons of cooling while maintaining chilled water leaving the evaporator at 42.0 ∘ F 42.0^\circ\text{F} 42. 0 ∘ F (with refrigerant evaporating at T L = 38.0 ∘ F T_L = 38.0^\circ\text{F} T L = 38. 0 ∘ F ). The cooling tower supplies condenser water returning to the condenser at 85.0 ∘ F 85.0^\circ\text{F} 85. 0 ∘ F (with refrigerant condensing at T H = 98.0 ∘ F T_H = 98.0^\circ\text{F} T H = 98. 0 ∘ F ). The electrical power input measured at the compressor motor terminals is 348.0 kW 348.0 \text{ kW} 348.0 kW .
Find:
The actual COP and the actual operating efficiency in kW/ton \text{kW/ton} kW/ton .
The theoretical maximum Reversed Carnot COP ( C O P R , C a r n o t COP_{R, Carnot} CO P R , C a r n o t ) based on internal refrigerant operating temperatures.
The Second Law (exergy) efficiency η I I \eta_{II} η II of the chiller compressor cycle.
Step-by-Step Solution:
Step 1: Calculate actual cooling capacity and actual COP. Q ˙ e v a p = 600 tons × 12 , 000 Btu hr ⋅ ton = 7 , 200 , 000 Btu hr \dot{Q}_{evap} = 600 \text{ tons} \times 12,000 \frac{\text{Btu}}{\text{hr}\cdot\text{ton}} = 7,200,000 \frac{\text{Btu}}{\text{hr}} Q ˙ e v a p = 600 tons × 12 , 000 hr ⋅ ton Btu = 7 , 200 , 000 hr Btu
Convert electric power input to Btu/hr \text{Btu/hr} Btu/hr ( 1 kW = 3 , 412.14 Btu/hr 1 \text{ kW} = 3,412.14 \text{ Btu/hr} 1 kW = 3 , 412.14 Btu/hr ): W ˙ i n = 348.0 kW × 3 , 412.14 Btu hr ⋅ kW = 1 , 187 , 425 Btu hr \dot{W}_{in} = 348.0 \text{ kW} \times 3,412.14 \frac{\text{Btu}}{\text{hr}\cdot\text{kW}} = 1,187,425 \frac{\text{Btu}}{\text{hr}} W ˙ in = 348.0 kW × 3 , 412.14 hr ⋅ kW Btu = 1 , 187 , 425 hr Btu COP a c t u a l = Q ˙ e v a p W ˙ i n = 7 , 200 , 000 1 , 187 , 425 = 6.063 \text{COP}_{actual} = \frac{\dot{Q}_{evap}}{\dot{W}_{in}} = \frac{7,200,000}{1,187,425} = 6.063 COP a c t u a l = W ˙ in Q ˙ e v a p = 1 , 187 , 425 7 , 200 , 000 = 6.063 Operating Efficiency = 348.0 kW 600 tons = 0.580 kW ton \text{Operating Efficiency} = \frac{348.0 \text{ kW}}{600 \text{ tons}} = 0.580 \frac{\text{kW}}{\text{ton}} Operating Efficiency = 600 tons 348.0 kW = 0.580 ton kW
Check consistency: COP = 3.51685 0.580 = 6.063 \text{COP} = \frac{3.51685}{0.580} = 6.063 COP = 0.580 3.51685 = 6.063 (matches).
Step 2: Calculate Carnot COP using absolute Rankine temperatures. T L = 38.0 ∘ F + 459.67 = 497.67 ∘ R T_L = 38.0^\circ\text{F} + 459.67 = 497.67^\circ\text{R} T L = 38. 0 ∘ F + 459.67 = 497.6 7 ∘ R T H = 98.0 ∘ F + 459.67 = 557.67 ∘ R T_H = 98.0^\circ\text{F} + 459.67 = 557.67^\circ\text{R} T H = 98. 0 ∘ F + 459.67 = 557.6 7 ∘ R Δ T = T H − T L = 557.67 − 497.67 = 60.0 ∘ R \Delta T = T_H - T_L = 557.67 - 497.67 = 60.0^\circ\text{R} Δ T = T H − T L = 557.67 − 497.67 = 60. 0 ∘ R COP R , C a r n o t = T L T H − T L = 497.67 ∘ R 60.0 ∘ R = 8.2945 \text{COP}_{R, Carnot} = \frac{T_L}{T_H - T_L} = \frac{497.67^\circ\text{R}}{60.0^\circ\text{R}} = 8.2945 COP R , C a r n o t = T H − T L T L = 60. 0 ∘ R 497.6 7 ∘ R = 8.2945
Step 3: Calculate Second Law Efficiency ( η I I \eta_{II} η II ). η I I = COP a c t u a l COP R , C a r n o t = 6.063 8.2945 = 0.7309 ⟹ 73.1 % \eta_{II} = \frac{\text{COP}_{actual}}{\text{COP}_{R, Carnot}} = \frac{6.063}{8.2945} = 0.7309 \implies 73.1\% η II = COP R , C a r n o t COP a c t u a l = 8.2945 6.063 = 0.7309 ⟹ 73.1%
7. NCEES Reference Handbook Navigation & Exam Traps
Section 1.3: Power & Refrigeration Cycles: Look up Carnot formulas, Rankine state point definitions, and Brayton cycle pressure ratio relations.
Absolute Temperature Error: Using ∘ F ^\circ\text{F} ∘ F instead of ∘ R ^\circ\text{R} ∘ R (or ∘ C ^\circ\text{C} ∘ C instead of K \text{K} K ) in Carnot COP calculations is the most common exam trap. For example, 38 98 − 38 = 0.633 \frac{38}{98 - 38} = 0.633 98 − 38 38 = 0.633 , which is completely erroneous.
COP Subscript Confusion: Never confuse COP R = T L T H − T L \text{COP}_R = \frac{T_L}{T_H - T_L} COP R = T H − T L T L with COP H P = T H T H − T L = COP R + 1 \text{COP}_{HP} = \frac{T_H}{T_H - T_L} = \text{COP}_R + 1 COP H P = T H − T L T H = COP R + 1 . When asked for heat pump COP, it must always exceed 1.0.