Study guide

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31

PE Mechanical: Machine Design and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology

1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety

2 Chapter 2: Physical & Mechanical Properties of Engineering Materials

2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep

3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections

3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis

4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects

4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses

5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics

5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics

6 Chapter 6: Fatigue Analysis & Dynamic Failure

6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage

7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints

7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors

8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding

8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding

9 Chapter 9: Power Transmission: Shafts & Gearing

9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing

10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers

10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels

11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods

12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power

12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics

13 Chapter 13: Kinematics, Mechatronics & Control Systems

13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls

14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods

14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly

15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion

15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31

Key Takeaways Explain This Topic AI

A cylindrical or spherical container qualifies as thin-walled when the inner radius to wall thickness ratio exceeds 10 ( r i / t > 10 r_i / t > 10 r i ​ / t > 10 or t < 0.1 r i t < 0.1 r_i t < 0.1 r i ​ ), validating the assumption of a uniform membrane stress distribution across the shell thickness.

In thin-walled cylindrical shells under internal pressure, circumferential hoop stress ( σ 1 = σ h = p r / t \sigma_1 = \sigma_h = p r / t σ 1 ​ = σ h ​ = p r / t ) is precisely twice the longitudinal axial stress ( σ 2 = σ l = p r / 2 t \sigma_2 = \sigma_l = p r / 2t σ 2 ​ = σ l ​ = p r /2 t ), whereas spherical shells develop uniform equibiaxial tension ( σ = p r / 2 t \sigma = p r / 2t σ = p r /2 t ).

Thick-walled cylinders governed by the Lamé equations experience severe non-linear stress gradients across the wall, with peak tangential hoop stress and peak triaxial shear stress τ max ⁡ = p i r o 2 / ( r o 2 − r i 2 ) \tau_{\max} = p_i r_o^2 / (r_o^2 - r_i^2) τ m a x ​ = p i ​ r o 2 ​ / ( r o 2 ​ − r i 2 ​ ) concentrating exclusively at the innermost bore surface ( r = r i r = r_i r = r i ​ ).

Autofrettage utilizes controlled overpressure to plastically deform inner bore fibers; upon elastic unloading of the outer jacket, high compressive residual hoop stresses are trapped at the bore, dramatically retarding fatigue crack initiation and boosting cyclic pressure capacity.

ASME BPVC Section VIII Division 1 mandates shell thickness t = P R / ( S E − 0.6 P ) t = P R / (S E - 0.6 P) t = PR / ( SE − 0.6 P ) , where formed heads require geometry-dependent sizing: 2:1 semi-ellipsoidal heads match cylindrical shell thickness, while hemispherical heads require approximately half the shell thickness.

Last updated: October 2026

11.1 Thin-Walled & Thick-Walled Pressure Vessels & Piping

Pressure containment vessels and high-energy piping systems represent mission-critical components across power generation, chemical processing, aerospace propulsion, and fluid power hydraulics. Ensuring structural integrity requires a rigorous understanding of multiaxial stress states, the geometric boundary separating thin-shell membrane behavior from thick-walled continuum behavior, and compliance with governing consensus safety codes such as the ASME Boiler and Pressure Vessel Code (BPVC).

Geometric Classification: Thin-Walled vs. Thick-Walled Threshold

The fundamental distinction between thin-walled and thick-walled vessels hinges on whether the radial stress gradient across the vessel wall can be safely neglected. Thin-Walled Shell (r/t > 10) Thick-Walled Cylinder (r/t <= 10)

  • +---------------------------------------+ +---------------------------------------+
  • | - Wall thickness t < 0.1 * r_i | | - Wall thickness t >= 0.1 * r_i |
  • | - Uniform membrane stress assumption | | - Steep non-linear stress gradient |
  • | - Radial normal stress sigma_r ~ 0 | | - Radial stress sigma_r != 0 (varies) |
  • | - Negligible bending across thickness | | - Peak stress at inner bore (r = r_i) |
  • +---------------------------------------+ +---------------------------------------+
  • The 10 % 10\% 10% Thickness Threshold

A vessel is classified as thin-walled when the ratio of its internal radius to wall thickness exceeds 10 10 10 : r i t > 10 ⟺ t < 0.10 r i \frac{r_i}{t} > 10 \quad \Longleftrightarrow \quad t < 0.10 r_i t r i ​ ​ > 10 ⟺ t < 0.10 r i ​

In terms of inside diameter D i D_i D i ​ , this corresponds to D i / t > 20 D_i / t > 20 D i ​ / t > 20 . In thin-walled shells:

The circumferential hoop stress and longitudinal stress are assumed uniform across the wall thickness.

Radial stress σ r \sigma_r σ r ​ ranges from − p -p − p on the inner wetted surface to 0 0 0 on the unpressurized exterior surface; because σ r ≪ σ h \sigma_r \ll \sigma_h σ r ​ ≪ σ h ​ , it is commonly neglected in elementary structural checks.

When r i / t ≤ 10 r_i / t \le 10 r i ​ / t ≤ 10 ( t ≥ 0.10 r i t \ge 0.10 r_i t ≥ 0.10 r i ​ ), the vessel must be analyzed as a thick-walled cylinder . Membrane theory becomes dangerously non-conservative, as peak tangential stresses at the inner bore significantly exceed the average membrane stress.

Thin-Walled Cylindrical & Spherical Shells

Consider a thin-walled cylindrical vessel with inside radius r r r , wall thickness t t t , and uniform internal gage pressure p p p . Thin-Walled Cylindrical Vessel Stresses

  • ^ Hoop Stress sigma_h (Circumferential)
  • |
  • +--------|--------+
  • / | \
  • / +-----v-----+ \
  • | | p (int) | | ----> Longitudinal Stress sigma_l (Axial)
  • \ +-----------+ /
  • \ /
  • +-----------------+
  • 1. Circumferential (Hoop) Stress ( σ 1 = σ h \sigma_1 = \sigma_h σ 1 ​ = σ h ​ )

Cutting the cylinder along a diametral longitudinal plane and enforcing static equilibrium between fluid pressure and wall tensile forces:

∑ F y = 0 ⟹ 2 σ h ( t ⋅ L ) − p ( 2 r ⋅ L ) = 0 \sum F_y = 0 \implies 2 \sigma_h (t \cdot L) - p (2 r \cdot L) = 0 ∑ F y ​ = 0 ⟹ 2 σ h ​ ( t ⋅ L ) − p ( 2 r ⋅ L ) = 0 σ h = p r t = p D 2 t \sigma_h = \frac{p r}{t} = \frac{p D}{2t} σ h ​ = t p r ​ = 2 t p D ​

2. Longitudinal (Axial) Stress ( σ 2 = σ l \sigma_2 = \sigma_l σ 2 ​ = σ l ​ )

For a closed-end cylinder, cutting a transverse cross section perpendicular to the vessel axis:

∑ F x = 0 ⟹ σ l ( 2 π r t ) − p ( π r 2 ) = 0 \sum F_x = 0 \implies \sigma_l (2 \pi r t) - p (\pi r^2) = 0 ∑ F x ​ = 0 ⟹ σ l ​ ( 2 π r t ) − p ( π r 2 ) = 0 σ l = p r 2 t = p D 4 t \sigma_l = \frac{p r}{2t} = \frac{p D}{4t} σ l ​ = 2 t p r ​ = 4 t p D ​

Key relationship: in a thin-walled cylinder, hoop stress is exactly twice the longitudinal stress :

σ h = 2 σ l \sigma_h = 2 \sigma_l σ h ​ = 2 σ l ​

This explains why over-pressurized thin-walled tubes or sausages burst along a longitudinal split rather than snapping transversely.

3. Radial Stress ( σ 3 = σ r \sigma_3 = \sigma_r σ 3 ​ = σ r ​ )

Radial stress acts perpendicular to the shell surface:

At the inner bore: σ r ( r i ) = − p \sigma_r(r_i) = -p σ r ​ ( r i ​ ) = − p (compressive contact pressure).

At the outer surface: σ r ( r o ) = 0 \sigma_r(r_o) = 0 σ r ​ ( r o ​ ) = 0 .

In thin-walled theory, since σ h / p = r / t > 10 \sigma_h / p = r / t > 10 σ h ​ / p = r / t > 10 , σ r \sigma_r σ r ​ is small compared to σ h \sigma_h σ h ​ , but it governs the critical maximum shear stress at the inner bore.

4. Thin-Walled Spherical Shells

By spherical symmetry, all planes passing through the center are identical:

∑ F = 0 ⟹ σ ( 2 π r t ) − p ( π r 2 ) = 0 \sum F = 0 \implies \sigma (2 \pi r t) - p (\pi r^2) = 0 ∑ F = 0 ⟹ σ ( 2 π r t ) − p ( π r 2 ) = 0 σ sphere = p r 2 t = p D 4 t \sigma_{\text{sphere}} = \frac{p r}{2t} = \frac{p D}{4t} σ sphere ​ = 2 t p r ​ = 4 t p D ​

A spherical vessel requires only half the wall thickness of a cylindrical shell of the same radius and design pressure to sustain the same membrane stress.

5. Maximum Shear Stress & Failure Criteria

The principal stresses on the inner surface of a thin-walled cylinder are:

σ 1 = σ h = p r t , σ 2 = σ l = p r 2 t , σ 3 = − p \sigma_1 = \sigma_h = \frac{p r}{t}, \quad \sigma_2 = \sigma_l = \frac{p r}{2t}, \quad \sigma_3 = -p σ 1 ​ = σ h ​ = t p r ​ , σ 2 ​ = σ l ​ = 2 t p r ​ , σ 3 ​ = − p

According to the Tresca Maximum Shear Stress Theory (MSST):

τ max ⁡ = σ 1 − σ 3 2 = p r t − ( − p ) 2 = p 2 ( r t + 1 ) ≈ p r 2 t \tau_{\max} = \frac{\sigma_1 - \sigma_3}{2} = \frac{\frac{pr}{t} - (-p)}{2} = \frac{p}{2}\left(\frac{r}{t} + 1\right) \approx \frac{pr}{2t} τ m a x ​ = 2 σ 1 ​ − σ 3 ​ ​ = 2 t p r ​ − ( − p ) ​ = 2 p ​ ( t r ​ + 1 ) ≈ 2 t p r ​

Under von Mises Distortion Energy Theory (DET), the equivalent stress σ ′ \sigma' σ ′ is:

σ ′ = σ 1 2 − σ 1 σ 2 + σ 2 2 = ( p r t ) 2 − ( p r t ) ( p r 2 t ) + ( p r 2 t ) 2 = 3 2 p r t ≈ 0.866 σ h \sigma' = \sqrt{\sigma_1^2 - \sigma_1 \sigma_2 + \sigma_2^2} = \sqrt{\left(\frac{pr}{t}\right)^2 - \left(\frac{pr}{t}\right)\left(\frac{pr}{2t}\right) + \left(\frac{pr}{2t}\right)^2} = \frac{\sqrt{3}}{2} \frac{pr}{t} \approx 0.866 \sigma_h σ ′ = σ 1 2 ​ − σ 1 ​ σ 2 ​ + σ 2 2 ​ ​ = ( t p r ​ ) 2 − ( t p r ​ ) ( 2 t p r ​ ) + ( 2 t p r ​ ) 2 ​ = 2 3 ​ ​ t p r ​ ≈ 0.866 σ h ​

Thick-Walled Cylinders: The Lamé Equations

When wall thickness t > 0.1 r i t > 0.1 r_i t > 0.1 r i ​ , stresses vary significantly with radius r r r . Gabriel Lamé derived the exact elastic continuum solution in 1852 by considering force equilibrium on an infinitesimal cylindrical element:

d σ r d r + σ r − σ t r = 0 \frac{d\sigma_r}{dr} + \frac{\sigma_r - \sigma_t}{r} = 0 d r d σ r ​ ​ + r σ r ​ − σ t ​ ​ = 0 Thick-Walled Cylinder Stress Distributions (Internal Pressure Only)

  • Stress
  • ^
  • | +-----------------------+ <-- Tangential Hoop Stress sigma_t (Peak at r = r_i)
  • | | \ |
  • | | \ |
  • | | \-------------------+ <-- Tangential Hoop Stress at r = r_o
  • | | |
  • 0 -+---+-----------------------+-------------------> Radius r
  • | | |
  • | | /-------------------+ <-- Radial Stress sigma_r = 0 at r = r_o
  • | | / |
  • | +-v---------------------+ <-- Radial Stress sigma_r = -p_i at r = r_i
  • r_i r_o
  • General Lamé Equations

For a thick-walled cylinder subjected to internal pressure p i p_i p i ​ and external pressure p o p_o p o ​ :

σ r ( r ) = p i r i 2 − p o r o 2 r o 2 − r i 2 − ( p i − p o ) r i 2 r o 2 r 2 ( r o 2 − r i 2 ) \sigma_r(r) = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} - \frac{(p_i - p_o) r_i^2 r_o^2}{r^2 (r_o^2 - r_i^2)} σ r ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​ − r 2 ( r o 2 ​ − r i 2 ​ ) ( p i ​ − p o ​ ) r i 2 ​ r o 2 ​ ​ σ t ( r ) = p i r i 2 − p o r o 2 r o 2 − r i 2 + ( p i − p o ) r i 2 r o 2 r 2 ( r o 2 − r i 2 ) \sigma_t(r) = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} + \frac{(p_i - p_o) r_i^2 r_o^2}{r^2 (r_o^2 - r_i^2)} σ t ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​ + r 2 ( r o 2 ​ − r i 2 ​ ) ( p i ​ − p o ​ ) r i 2 ​ r o 2 ​ ​

For closed-end cylinders, the longitudinal stress σ l \sigma_l σ l ​ is uniform across the wall:

σ l = p i r i 2 − p o r o 2 r o 2 − r i 2 \sigma_l = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} σ l ​ = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​

Special Case: Internal Pressure Only ( p o = 0 p_o = 0 p o ​ = 0 )

Setting external pressure p o = 0 p_o = 0 p o ​ = 0 simplifies the expressions to:

σ r ( r ) = p i r i 2 r o 2 − r i 2 ( 1 − r o 2 r 2 ) \sigma_r(r) = \frac{p_i r_i^2}{r_o^2 - r_i^2} \left( 1 - \frac{r_o^2}{r^2} \right) σ r ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ ​ ( 1 − r 2 r o 2 ​ ​ ) σ t ( r ) = p i r i 2 r o 2 − r i 2 ( 1 + r o 2 r 2 ) \sigma_t(r) = \frac{p_i r_i^2}{r_o^2 - r_i^2} \left( 1 + \frac{r_o^2}{r^2} \right) σ t ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ ​ ( 1 + r 2 r o 2 ​ ​ ) σ l = p i r i 2 r o 2 − r i 2 \sigma_l = \frac{p_i r_i^2}{r_o^2 - r_i^2} σ l ​ = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ ​

Peak Bore Stresses & Inefficiency of Wall Thickening

The critical peak stress state occurs at the innermost bore ( r = r i r = r_i r = r i ​ ):

σ r ( r i ) = − p i \sigma_r(r_i) = -p_i σ r ​ ( r i ​ ) = − p i ​ σ t ( r i ) = p i ( r o 2 + r i 2 r o 2 − r i 2 ) \sigma_t(r_i) = p_i \left( \frac{r_o^2 + r_i^2}{r_o^2 - r_i^2} \right) σ t ​ ( r i ​ ) = p i ​ ( r o 2 ​ − r i 2 ​ r o 2 ​ + r i 2 ​ ​ ) τ max ⁡ ( r i ) = σ t ( r i ) − σ r ( r i ) 2 = p i ( r o 2 r o 2 − r i 2 ) \tau_{\max}(r_i) = \frac{\sigma_t(r_i) - \sigma_r(r_i)}{2} = p_i \left( \frac{r_o^2}{r_o^2 - r_i^2} \right) τ m a x ​ ( r i ​ ) = 2 σ t ​ ( r i ​ ) − σ r ​ ( r i ​ ) ​ = p i ​ ( r o 2 ​ − r i 2 ​ r o 2 ​ ​ )

At the outer surface ( r = r o r = r_o r = r o ​ ):

σ r ( r o ) = 0 \sigma_r(r_o) = 0 σ r ​ ( r o ​ ) = 0 σ t ( r o ) = p i ( 2 r i 2 r o 2 − r i 2 ) \sigma_t(r_o) = p_i \left( \frac{2 r_i^2}{r_o^2 - r_i^2} \right) σ t ​ ( r o ​ ) = p i ​ ( r o 2 ​ − r i 2 ​ 2 r i 2 ​ ​ )

Important

As wall thickness increases toward infinity ( r o / r i → ∞ r_o / r_i \to \infty r o ​ / r i ​ → ∞ ), the peak tangential hoop stress at the inner bore asymptotes to σ t ( r i ) → p i \sigma_t(r_i) \to p_i σ t ​ ( r i ​ ) → p i ​ . Because the bore also carries σ r = − p i \sigma_r = -p_i σ r ​ = − p i ​ , the bore shear stress approaches τ max ⁡ → p i \tau_{\max} \to p_i τ m a x ​ → p i ​ , so by the Tresca criterion the bore yields when p i p_i p i ​ reaches about S y / 2 S_y/2 S y ​ /2 no matter how thick the wall is made. Beyond a wall ratio of about r o / r i = 3 r_o/r_i = 3 r o ​ / r i ​ = 3 , extra thickness buys almost nothing, so designers turn to autofrettage or shrink-fitted compound cylinders.

The Autofrettage Principle & Residual Stress Conditioning

To overcome the elastic limitation of monobloc thick-walled cylinders, engineers use autofrettage (French for "self-hooping"). Autofrettage is widely employed in artillery gun barrels, ultra-high-pressure waterjet intensifiers ( 60 , 000 psi 60,000\text{ psi} 60 , 000 psi ), and diesel common-rail fuel injection manifolds. The Autofrettage Process Cycle

  • Phase 1: Overpressurization Phase 2: Elastic Unloading Phase 3: Residual State
  • +---------------------------+ +---------------------------+ +---------------------------+
  • | Plastic zone at bore | | Outer elastic jacket | | High compressive residual |
  • | Elastic outer mantle | -----> | contracts and springs | -----> | hoop stress at inner bore |
  • | Fully yields inner fibers | | back elastically | | prevents fatigue crack tip|
  • +---------------------------+ +---------------------------+ +---------------------------+
  • Mechanics of Autofrettage

Overpressurization : The vessel is subjected to an internal autofrettage pressure p auto p_{\text{auto}} p auto ​ that drives the inner bore past its yield strength, creating an internal plastic deformation zone up to an intermediate radius r p r_p r p ​ ( r i < r p < r o r_i < r_p < r_o r i ​ < r p ​ < r o ​ ), while the outer mantle remains elastic.

Elastic Recovery : When p auto p_{\text{auto}} p auto ​ is released, the outer elastic layer attempts to contract back to its original dimensions. The permanently stretched inner plastic layer resists this contraction.

Resulting Residual Stress Field : The outer layer clamps down on the inner core, locking in a large compressive residual hoop stress at the inner bore ( σ t , res < 0 \sigma_{t,\text{res}} < 0 σ t , res ​ < 0 ).

Service Advantage : Under subsequent operating service pressure p op p_{\text{op}} p op ​ , the tensile hoop stress induced at the bore must first overcome this pre-existing compressive residual stress. Consequently, the net mean stress is shifted downward, significantly extending fatigue life and preventing bore crack propagation.

ASME BPVC Section VIII Division 1 Code Rules

Industrial pressure vessels operating above 15 psig 15\text{ psig} 15 psig are governed by the ASME Boiler and Pressure Vessel Code (BPVC) Section VIII Division 1. ASME BPVC adopts a "design-by-rule" methodology that modifies thin-shell equations to account for thick-shell curvature, weld joint quality, and material allowable stresses.

Code Sizing Variables

P P P : Maximum Allowable Working Pressure (MAWP) in psi \text{psi} psi (or MPa \text{MPa} MPa ).

R R R : Inside radius in in \text{in} in (corroded condition: R = R initial + C A R = R_{\text{initial}} + CA R = R initial ​ + C A ).

S S S : Maximum allowable stress of the material in psi \text{psi} psi (from ASME Section II Part D, typically S u t / 3.5 S_{ut} / 3.5 S u t ​ /3.5 or 2 / 3 S y 2/3 S_y 2/3 S y ​ ).

E E E : Weld joint efficiency ( 0.70 ≤ E ≤ 1.00 0.70 \le E \le 1.00 0.70 ≤ E ≤ 1.00 ):

E = 1.00 E = 1.00 E = 1.00 : Full radiography (Type 1 butt welds with 100% volumetric NDE per UW-11(a)).

E = 0.85 E = 0.85 E = 0.85 : Spot radiography (per UW-11(b) and UW-52).

E = 0.70 E = 0.70 E = 0.70 : Visual inspection only (no radiography per UW-11(c)).

C A CA C A : Corrosion allowance specified by the process engineer (typically 1 / 16 in 1/16\text{ in} 1/16 in to 1 / 4 in 1/4\text{ in} 1/4 in , or 1.5 mm 1.5\text{ mm} 1.5 mm to 6.0 mm 6.0\text{ mm} 6.0 mm ).

Cylindrical Shell Thickness Formulas (ASME UG-27)

Circumferential stress (longitudinal joint) governs shell thickness: t = P R S E − 0.6 P t = \frac{P R}{S E - 0.6 P} t = SE − 0.6 P PR ​

Longitudinal stress (circumferential joint) governs axial capacity: t = P R 2 S E + 0.4 P t = \frac{P R}{2 S E + 0.4 P} t = 2 SE + 0.4 P PR ​

(The empirical 0.6 P 0.6 P 0.6 P and 0.4 P 0.4 P 0.4 P factors correct the thin-shell membrane equations for non-linear stress distribution through the thickness up to t ≤ 0.5 R t \le 0.5 R t ≤ 0.5 R or P ≤ 0.385 S E P \le 0.385 S E P ≤ 0.385 SE .)

Formed Head Geometries & Sizing Rules (ASME UG-32)

Vessel heads enclose the ends of cylindrical shells. The three standard ASME formed head geometries are: Hemispherical Head 2:1 Semi-Ellipsoidal Head ASME Torispherical Head

(UG-32f) (UG-32d) (UG-32e)

___ ____ _____

.-' '-. .-' '-. .-' '-.

.' '. .' '. .' '.

  • / \ / \ / \
  • | | | | | |
  • | | | | | |
  • Radius R = D/2 Depth h = D/4 Crown L = D, Knuckle r_k = 0.06D
  • Lowest thickness Matches shell thickness Prone to knuckle stress peak
  • Hemispherical Head (UG-32f) : t = P R 2 S E − 0.2 P t = \frac{P R}{2 S E - 0.2 P} t = 2 SE − 0.2 P PR ​

A hemispherical head requires approximately half the thickness of the adjacent cylindrical shell, making it the most material-efficient head geometry, though more costly to fabricate.

2:1 Semi-Ellipsoidal Head (UG-32d) :

Major-to-minor axis ratio is 2 : 1 2:1 2 : 1 (inside depth h = D / 4 h = D/4 h = D /4 ): t = P D 2 S E − 0.2 P = P R S E − 0.1 P t = \frac{P D}{2 S E - 0.2 P} = \frac{P R}{S E - 0.1 P} t = 2 SE − 0.2 P P D ​ = SE − 0.1 P PR ​

Because the thickness formula closely matches the cylindrical shell formula, the head thickness is identical to the shell thickness, simplifying fabrication and welding transition.

ASME Flanged and Dished (Torispherical) Head (UG-32e) :

Consists of a spherical crown of radius L L L (typically L = D L = D L = D ) and a toroidal knuckle of radius r k r_k r k ​ ( r k ≥ 0.06 D r_k \ge 0.06 D r k ​ ≥ 0.06 D and r k ≥ 3 t r_k \ge 3 t r k ​ ≥ 3 t ): t = 0.885 P L S E − 0.1 P t = \frac{0.885 P L}{S E - 0.1 P} t = SE − 0.1 P 0.885 P L ​

Torispherical heads are easier to press than ellipsoidal heads, but high localized bending stresses at the knuckle mandate roughly 77 % 77\% 77% greater thickness than 2:1 ellipsoidal heads.

Formed Head Geometry Comparison Table

Head Type Governing Code Geometric Relation Minimum Thickness Formula Relative Thickness Factor

Hemispherical ASME UG-32(f) Spherical radius R = D / 2 R = D/2 R = D /2 t = P R 2 S E − 0.2 P t = \frac{P R}{2 S E - 0.2 P} t = 2 SE − 0.2 P PR ​ 1.00 1.00 1.00 (Baseline, thinnest)

2:1 Semi-Ellipsoidal ASME UG-32(d) Depth h = D / 4 h = D / 4 h = D /4 t = P D 2 S E − 0.2 P t = \frac{P D}{2 S E - 0.2 P} t = 2 SE − 0.2 P P D ​ ≈ 2.00 \approx 2.00 ≈ 2.00 (Matches shell)

Torispherical (F&D) ASME UG-32(e) Crown L = D L = D L = D , Knuckle r k = 0.06 D r_k = 0.06 D r k ​ = 0.06 D t = 0.885 P L S E − 0.1 P t = \frac{0.885 P L}{S E - 0.1 P} t = SE − 0.1 P 0.885 P L ​ ≈ 3.54 \approx 3.54 ≈ 3.54 (Heaviest head)

Flat Welded Head ASME UG-34 Flat plate, factor C ≈ 0.33 C \approx 0.33 C ≈ 0.33 t = d C P S E t = d \sqrt{\frac{C P}{S E}} t = d SE CP ​ ​ ≈ 6.0 – 10.0 \approx 6.0\text{--}10.0 ≈ 6.0 – 10.0 (Very thick)

Process & Power Piping (ASME B31)

Pressure piping is designed to the ASME B31 code sections, chiefly B31.1 Power Piping (boiler external piping, steam and power plant systems) and B31.3 Process Piping (chemical, petroleum and similar plants). For straight pipe under internal pressure with t < D / 6 t < D/6 t < D /6 , ASME B31.3 gives the pressure design thickness t = P D 2 ( S E W + P Y ) t = \frac{P D}{2\,(S E W + P Y)} t = 2 ( SE W + P Y ) P D ​

where:

D D D is the pipe outside diameter and P P P the internal design gage pressure.

S S S is the code allowable stress at the design temperature, and E E E is the longitudinal-joint quality factor ( 1.0 1.0 1.0 for seamless pipe).

W W W is the weld joint strength reduction factor ( 1.0 1.0 1.0 below the creep range).

Y Y Y is a coefficient equal to 0.4 0.4 0.4 for ferritic steels below 900 ∘ F 900^\circ\text{F} 90 0 ∘ F ( 482 ∘ C 482^\circ\text{C} 48 2 ∘ C ).

The minimum required thickness adds mechanical, corrosion and erosion allowances: t m = t + c t_m = t + c t m ​ = t + c . Seamless pipe may be supplied up to 12.5 % 12.5\% 12.5% under its nominal wall, so the selected nominal wall must satisfy t nom ≥ t m / 0.875 t_{\text{nom}} \ge t_m / 0.875 t nom ​ ≥ t m ​ /0.875 . A traditional estimate of the needed schedule number is Sch ≈ 1,000 P / S \text{Sch} \approx 1{,}000 P/S Sch ≈ 1 , 000 P / S .

Piping design also checks thermal expansion and flexibility (anchors, guides, loops and expansion joints keep the displacement stress range within code limits), support and hanger spacing, and water hammer : a sudden valve closure raises pressure by Δ p = ρ a Δ v \Delta p = \rho\, a\, \Delta v Δ p = ρ a Δ v , where a a a is the pressure-wave speed (about 1,400 m/s 1{,}400\,\text{m/s} 1 , 400 m/s in water in a stiff pipe), so a 2 m/s 2\,\text{m/s} 2 m/s velocity change can add roughly 2.8 MPa 2.8\,\text{MPa} 2.8 MPa ( 400 psi 400\,\text{psi} 400 psi ).

Tip

Mini-example (B31.3 wall thickness): NPS 4 seamless carbon steel pipe ( D = 4.500 in D = 4.500\text{ in} D = 4.500 in ) carries P = 600 psig P = 600\text{ psig} P = 600 psig with S = 20,000 psi S = 20{,}000\text{ psi} S = 20 , 000 psi , E = W = 1.0 E = W = 1.0 E = W = 1.0 , Y = 0.4 Y = 0.4 Y = 0.4 and a corrosion allowance c = 0.0625 in c = 0.0625\text{ in} c = 0.0625 in .

t = 600 ( 4.500 ) 2 [ 20,000 + 600 ( 0.4 ) ] = 2,700 40,480 = 0.0667 in t = \dfrac{600(4.500)}{2[20{,}000 + 600(0.4)]} = \dfrac{2{,}700}{40{,}480} = 0.0667\text{ in} t = 2 [ 20 , 000 + 600 ( 0.4 )] 600 ( 4.500 ) ​ = 40 , 480 2 , 700 ​ = 0.0667 in , so t m = 0.0667 + 0.0625 = 0.129 in t_m = 0.0667 + 0.0625 = 0.129\text{ in} t m ​ = 0.0667 + 0.0625 = 0.129 in and t nom ≥ 0.129 / 0.875 = 0.148 in t_{\text{nom}} \ge 0.129/0.875 = 0.148\text{ in} t nom ​ ≥ 0.129/0.875 = 0.148 in .

Schedule 40 NPS 4 pipe (wall 0.237 in 0.237\text{ in} 0.237 in ) satisfies the requirement; Schedule 10 ( 0.120 in 0.120\text{ in} 0.120 in ) does not.

Realistic Worked Engineering Scenario: Chemical Reactor Vessel Sizing Chemical Reactor Pressure Vessel

  • +----------------- 2:1 Ellipsoidal Head -----------------+
  • | |
  • +=========================================================+
  • | Internal Design Pressure P = 450 psig |
  • | Design Temperature = 300 deg F |
  • | Inside Diameter D_i = 48.0 in (R = 24.0 in) |
  • | Material: SA-516 Grade 70 Steel |
  • | Allowable Stress S = 20,000 psi |
  • | Weld Joint Efficiency E = 0.85 (Spot RT) |
  • | Corrosion Allowance CA = 0.125 in (1/8 in) |
  • +=========================================================+
  • | |
  • +------------------- Hemispherical Head ------------------+
  • Problem Statement

A chemical process engineering facility requires a new carbon steel autoclave reactor vessel. The design specifications are:

Design internal pressure: P = 450 psig P = 450\text{ psig} P = 450 psig

Inside diameter: D i = 48.0 in D_i = 48.0\text{ in} D i ​ = 48.0 in (initial uncorroded inside radius R 0 = 24.0 in R_0 = 24.0\text{ in} R 0 ​ = 24.0 in )

Design temperature: 300 ∘ F 300^\circ\text{F} 30 0 ∘ F

Vessel material: ASME SA-516 Grade 70 plate ( S = 20 , 000 psi S = 20,000\text{ psi} S = 20 , 000 psi , S y = 38 , 000 psi S_y = 38,000\text{ psi} S y ​ = 38 , 000 psi , S u t = 70 , 000 psi S_{ut} = 70,000\text{ psi} S u t ​ = 70 , 000 psi )

  • Joint efficiency: E = 0.85 E = 0.85 E = 0.85 (spot radiographed Category A and B butt welds)
  • Corrosion allowance: C A = 0.125 in CA = 0.125\text{ in} C A = 0.125 in ( 1 / 8 in 1/8\text{ in} 1/8 in )

Calculate:

The minimum required cylindrical shell thickness t shell t_{\text{shell}} t shell ​ and nominal plate specification.

The minimum required thickness for the top 2:1 semi-ellipsoidal head and bottom hemispherical head.

Verify whether the vessel satisfies the thin-walled threshold ( r / t > 10 r/t > 10 r / t > 10 ).

The peak bore stresses and maximum shear stress at the inner radius using thick-walled Lamé theory, and compute the static factor of safety against yielding.

  • Step-by-Step Mathematical Solution
  • Step 1: Cylindrical Shell Thickness Sizing (UG-27)

Under corroded conditions, the active inside radius is: R = R 0 + C A = 24.0 + 0.125 = 24.125 in R = R_0 + CA = 24.0 + 0.125 = 24.125\text{ in} R = R 0 ​ + C A = 24.0 + 0.125 = 24.125 in

Applying the ASME UG-27 circumferential hoop equation: t calc = P R S E − 0.6 P = 450 psi × 24.125 in ( 20 , 000 psi × 0.85 ) − ( 0.6 × 450 psi ) t_{\text{calc}} = \frac{P R}{S E - 0.6 P} = \frac{450\text{ psi} \times 24.125\text{ in}}{(20,000\text{ psi} \times 0.85) - (0.6 \times 450\text{ psi})} t calc ​ = SE − 0.6 P PR ​ = ( 20 , 000 psi × 0.85 ) − ( 0.6 × 450 psi ) 450 psi × 24.125 in ​ t calc = 10 , 856.25 lbf/in 17 , 000 − 270 psi = 10 , 856.25 16 , 730 = 0.6489 in t_{\text{calc}} = \frac{10,856.25\text{ lbf/in}}{17,000 - 270\text{ psi}} = \frac{10,856.25}{16,730} = 0.6489\text{ in} t calc ​ = 17 , 000 − 270 psi 10 , 856.25 lbf/in ​ = 16 , 730 10 , 856.25 ​ = 0.6489 in

Adding the corrosion allowance to obtain total nominal thickness: t nominal = t calc + C A = 0.6489 + 0.125 = 0.7739 in t_{\text{nominal}} = t_{\text{calc}} + CA = 0.6489 + 0.125 = 0.7739\text{ in} t nominal ​ = t calc ​ + C A = 0.6489 + 0.125 = 0.7739 in

Selecting the next standard commercial plate size: 13 / 16 in 13/16\text{ in} 13/16 in plate ( 0.8125 in 0.8125\text{ in} 0.8125 in ) , or commonly 7 / 8 in 7/8\text{ in} 7/8 in plate ( 0.875 in 0.875\text{ in} 0.875 in ) .

Step 2: Formed Heads Thickness Sizing (UG-32)

Top 2:1 Semi-Ellipsoidal Head :

Corroded inside diameter: D = 2 R = 2 × 24.125 = 48.25 in D = 2 R = 2 \times 24.125 = 48.25\text{ in} D = 2 R = 2 × 24.125 = 48.25 in . t ellip = P D 2 S E − 0.2 P = 450 × 48.25 2 ( 20 , 000 ) ( 0.85 ) − 0.2 ( 450 ) = 21 , 712.5 34 , 000 − 90 = 21 , 712.5 33 , 910 = 0.6403 in t_{\text{ellip}} = \frac{P D}{2 S E - 0.2 P} = \frac{450 \times 48.25}{2(20,000)(0.85) - 0.2(450)} = \frac{21,712.5}{34,000 - 90} = \frac{21,712.5}{33,910} = 0.6403\text{ in} t ellip ​ = 2 SE − 0.2 P P D ​ = 2 ( 20 , 000 ) ( 0.85 ) − 0.2 ( 450 ) 450 × 48.25 ​ = 34 , 000 − 90 21 , 712.5 ​ = 33 , 910 21 , 712.5 ​ = 0.6403 in

Total nominal thickness: t nom, ellip = 0.6403 + 0.125 = 0.7653 in ⟹ specify 13 / 16 in ( 0.8125 in ) plate t_{\text{nom, ellip}} = 0.6403 + 0.125 = 0.7653\text{ in} \implies \text{specify } 13/16\text{ in } (0.8125\text{ in}) \text{ plate} t nom, ellip ​ = 0.6403 + 0.125 = 0.7653 in ⟹ specify 13/16 in ( 0.8125 in ) plate

Bottom Hemispherical Head : t hemi = P R 2 S E − 0.2 P = 450 × 24.125 34 , 000 − 90 = 10 , 856.25 33 , 910 = 0.3201 in t_{\text{hemi}} = \frac{P R}{2 S E - 0.2 P} = \frac{450 \times 24.125}{34,000 - 90} = \frac{10,856.25}{33,910} = 0.3201\text{ in} t hemi ​ = 2 SE − 0.2 P PR ​ = 34 , 000 − 90 450 × 24.125 ​ = 33 , 910 10 , 856.25 ​ = 0.3201 in

Total nominal thickness: t nom, hemi = 0.3201 + 0.125 = 0.4451 in ⟹ specify 1 / 2 in ( 0.500 in ) plate t_{\text{nom, hemi}} = 0.3201 + 0.125 = 0.4451\text{ in} \implies \text{specify } 1/2\text{ in } (0.500\text{ in}) \text{ plate} t nom, hemi ​ = 0.3201 + 0.125 = 0.4451 in ⟹ specify 1/2 in ( 0.500 in ) plate

(Notice that the hemispherical head requires only 58 % 58\% 58% of the nominal thickness of the 2:1 ellipsoidal head).

Step 3: Thin-Wall Ratio Verification

Evaluating the thin-walled criterion on the corroded shell ( t = 0.6489 in t = 0.6489\text{ in} t = 0.6489 in , r = 24.125 in r = 24.125\text{ in} r = 24.125 in ): r t = 24.125 in 0.6489 in = 37.18 ≫ 10 \frac{r}{t} = \frac{24.125\text{ in}}{0.6489\text{ in}} = 37.18 \gg 10 t r ​ = 0.6489 in 24.125 in ​ = 37.18 ≫ 10

Because r / t = 37.2 r/t = 37.2 r / t = 37.2 is well above 10 10 10 , the vessel operates in the thin-walled shell regime.

Step 4: Lamé Thick-Walled Stress Analysis & Factor of Safety

To verify peak bore stress, apply Lamé's formulation using corroded dimensions: r i = 24.125 in r_i = 24.125\text{ in} r i ​ = 24.125 in , t = 0.6489 in ⟹ r o = r i + t = 24.7739 in t = 0.6489\text{ in} \implies r_o = r_i + t = 24.7739\text{ in} t = 0.6489 in ⟹ r o ​ = r i ​ + t = 24.7739 in .

Tangential hoop stress at inner bore ( r = r i r = r_i r = r i ​ ): σ t ( r i ) = P ( r o 2 + r i 2 r o 2 − r i 2 ) = 450 ( 24.7739 2 + 24.125 2 24.7739 2 − 24.125 2 ) \sigma_t(r_i) = P \left( \frac{r_o^2 + r_i^2}{r_o^2 - r_i^2} \right) = 450 \left( \frac{24.7739^2 + 24.125^2}{24.7739^2 - 24.125^2} \right) σ t ​ ( r i ​ ) = P ( r o 2 ​ − r i 2 ​ r o 2 ​ + r i 2 ​ ​ ) = 450 ( 24.773 9 2 − 24.12 5 2 24.773 9 2 + 24.12 5 2 ​ ) r o 2 = 613.746 , r i 2 = 582.016 ⟹ r o 2 + r i 2 = 1 , 195.762 , r o 2 − r i 2 = 31.730 r_o^2 = 613.746, \quad r_i^2 = 582.016 \implies r_o^2 + r_i^2 = 1,195.762, \quad r_o^2 - r_i^2 = 31.730 r o 2 ​ = 613.746 , r i 2 ​ = 582.016 ⟹ r o 2 ​ + r i 2 ​ = 1 , 195.762 , r o 2 ​ − r i 2 ​ = 31.730 σ t ( r i ) = 450 × ( 1 , 195.762 31.730 ) = 450 × 37.685 = 16 , 958 psi \sigma_t(r_i) = 450 \times \left( \frac{1,195.762}{31.730} \right) = 450 \times 37.685 = 16,958\text{ psi} σ t ​ ( r i ​ ) = 450 × ( 31.730 1 , 195.762 ​ ) = 450 × 37.685 = 16 , 958 psi

(Compare this to the thin-wall formula: σ h = P R / t = 450 × 24.125 / 0.6489 = 16 , 730 psi \sigma_h = P R / t = 450 \times 24.125 / 0.6489 = 16,730\text{ psi} σ h ​ = PR / t = 450 × 24.125/0.6489 = 16 , 730 psi . The Lamé bore stress is 1.4 % 1.4\% 1.4% higher due to curvature).

Radial stress at inner bore: σ r ( r i ) = − P = − 450 psi \sigma_r(r_i) = -P = -450\text{ psi} σ r ​ ( r i ​ ) = − P = − 450 psi .

Longitudinal stress: σ l = P r i 2 r o 2 − r i 2 = 450 × 582.016 31.730 = 8 , 254 psi \sigma_l = \frac{P r_i^2}{r_o^2 - r_i^2} = \frac{450 \times 582.016}{31.730} = 8,254\text{ psi} σ l ​ = r o 2 ​ − r i 2 ​ P r i 2 ​ ​ = 31.730 450 × 582.016 ​ = 8 , 254 psi .

Maximum shear stress at inner bore: τ max ⁡ = σ t ( r i ) − σ r ( r i ) 2 = 16 , 958 − ( − 450 ) 2 = 17 , 408 2 = 8 , 704 psi \tau_{\max} = \frac{\sigma_t(r_i) - \sigma_r(r_i)}{2} = \frac{16,958 - (-450)}{2} = \frac{17,408}{2} = 8,704\text{ psi} τ m a x ​ = 2 σ t ​ ( r i ​ ) − σ r ​ ( r i ​ ) ​ = 2 16 , 958 − ( − 450 ) ​ = 2 17 , 408 ​ = 8 , 704 psi

Static Factor of Safety against yield ( S y = 38 , 000 psi S_y = 38,000\text{ psi} S y ​ = 38 , 000 psi ):

Under Tresca MSST ( S s y = 0.5 S y = 19 , 000 psi S_{sy} = 0.5 S_y = 19,000\text{ psi} S sy ​ = 0.5 S y ​ = 19 , 000 psi ): F S yield = S s y τ max ⁡ = 19 , 000 psi 8 , 704 psi = 2.18 FS_{\text{yield}} = \frac{S_{sy}}{\tau_{\max}} = \frac{19,000\text{ psi}}{8,704\text{ psi}} = 2.18 F S yield ​ = τ m a x ​ S sy ​ ​ = 8 , 704 psi 19 , 000 psi ​ = 2.18

Under von Mises DET: σ ′ = 1 2 [ ( 16 , 958 − 8 , 254 ) 2 + ( 8 , 254 − ( − 450 ) ) 2 + ( − 450 − 16 , 958 ) 2 ] = 15 , 076 psi \sigma' = \sqrt{\frac{1}{2}\left[ (16,958 - 8,254)^2 + (8,254 - (-450))^2 + (-450 - 16,958)^2 \right]} = 15,076\text{ psi} σ ′ = 2 1 ​ [ ( 16 , 958 − 8 , 254 ) 2 + ( 8 , 254 − ( − 450 ) ) 2 + ( − 450 − 16 , 958 ) 2 ] ​ = 15 , 076 psi F S DET = S y σ ′ = 38 , 000 15 , 076 = 2.52 FS_{\text{DET}} = \frac{S_y}{\sigma'} = \frac{38,000}{15,076} = 2.52 F S DET ​ = σ ′ S y ​ ​ = 15 , 076 38 , 000 ​ = 2.52

The vessel has substantial reserve against yielding, consistent with the margins built into the design-by-rule formulas.