Study guide

3.2 Direct Shear, Bearing & Transverse Shear in Beams

PE Mechanical: Machine Design and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology

1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety

2 Chapter 2: Physical & Mechanical Properties of Engineering Materials

2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep

3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections

3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis

4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects

4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses

5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics

5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics

6 Chapter 6: Fatigue Analysis & Dynamic Failure

6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage

7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints

7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors

8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding

8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding

9 Chapter 9: Power Transmission: Shafts & Gearing

9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing

10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers

10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels

11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods

12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power

12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics

13 Chapter 13: Kinematics, Mechatronics & Control Systems

13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls

14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods

14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly

15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion

15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement

3.2 Direct Shear, Bearing & Transverse Shear in Beams

Key Takeaways Explain This Topic AI

Direct shear assumes an average stress across the shear plane ( τ avg = V / A \tau_{\text{avg}} = V/A τ avg ​ = V / A ), where double-shear joints divide the applied load across two shear planes ( V = P / 2 V = P/2 V = P /2 ), halving the shear stress.

Transverse shear stress in beams follows τ = V Q I b \tau = \frac{VQ}{Ib} τ = I b V Q ​ , where Q Q Q is the first moment of area above the cut plane; for solid rectangular sections τ max ⁡ = 1.5 V / A \tau_{\max} = 1.5 V/A τ m a x ​ = 1.5 V / A , and for solid circular sections τ max ⁡ = 4 3 V / A \tau_{\max} = \frac{4}{3} V/A τ m a x ​ = 3 4 ​ V / A at the neutral axis.

In wide-flange I-beams, the thin web carries over 90 % 90\% 90% to 98 % 98\% 98% of the vertical transverse shear force, whereas the flanges resist the predominant share of bending moments.

Built-up beams transfer shear flow q = V Q / I q = VQ/I q = V Q / I across each joint, so fastener pitch is s = n V f a s t e n e r / q s = n V_{fastener}/q s = n V f a s t e n er ​ / q , with closer spacing where the shear force is largest.

Last updated: October 2026

3.2 Direct Shear, Bearing & Transverse Shear in Beams

Shear stresses develop whenever internal forces tend to make adjacent material planes slide relative to one another. Machine designers must separate direct (average) shear in pins, rivets, keys and bolts from transverse shear that accompanies bending in beams. (Torsional shear from twisting moments is treated separately in Section 3.3.) Both appear on nearly every connection and beam problem, usually alongside a bearing-stress check.

1. Direct (Average) Shear in Fasteners & Joint Design

Direct shear occurs in bolted joints, rivets, cotter pins, and drive keys where parallel opposing forces act across a well-defined shear plane. The average direct shear stress is: τ avg = V A \tau_{\text{avg}} = \frac{V}{A} τ avg ​ = A V ​

where V V V is the total internal shear force acting parallel to cross-sectional area A A A . Single Shear Joint: Double Shear Joint (Clevis & Pin):

  • P P/2
  • [===========] [==============]
  • | Shear Plane | Shear Plane 1
  • V P <--- [==============]
  • [===========] | Shear Plane 2
  • P P/2
  • [==============]
  • Single vs. Double Shear Configurations

Single Shear: A single shear interface resists the external tensile load P P P . The internal shear force is V = P V = P V = P . For a cylindrical pin or bolt of diameter d d d : τ = P A = 4 P π d 2 \tau = \frac{P}{A} = \frac{4 P}{\pi d^2} τ = A P ​ = π d 2 4 P ​

Double Shear: Two shear interfaces resist the load (such as a clevis-and-tongue connection). The applied load divides equally between both planes ( V = P / 2 V = P/2 V = P /2 ): τ = P / 2 A = P 2 A = 2 P π d 2 \tau = \frac{P / 2}{A} = \frac{P}{2 A} = \frac{2 P}{\pi d^2} τ = A P /2 ​ = 2 A P ​ = π d 2 2 P ​ Impact: Double shear reduces the shear stress on the pin by 50% relative to single shear for the same load and pin diameter, or permits a 29.3 % 29.3\% 29.3% reduction in pin diameter for the same allowable shear stress.

Bearing Stress in Pinned Joints

Simultaneously, the contact interface between the cylindrical fastener and the plate hole wall experiences compressive bearing stress σ b \sigma_b σ b ​ , evaluated over the projected rectangular area A b = d ⋅ t A_b = d \cdot t A b ​ = d ⋅ t : σ b = P d ⋅ t \sigma_b = \frac{P}{d \cdot t} σ b ​ = d ⋅ t P ​

where t t t is the plate thickness and d d d is the nominal pin diameter.

2. Transverse Shear Stress in Beams

When a beam is subjected to transverse loading, internal bending moments M ( x ) M(x) M ( x ) and internal shear forces V ( x ) V(x) V ( x ) coexist. The variation of bending stress along the span ( d M / d x = V dM/dx = V d M / d x = V ) creates horizontal interlaminar shear stresses. By complementary shear equilibrium ( τ x y = τ y x \tau_{xy} = \tau_{yx} τ x y ​ = τ y x ​ ), this horizontal shear stress is identical in magnitude to the vertical transverse shear stress acting across the beam cross-section.

The Transverse Shear Formula τ = V Q I b \tau = \frac{V Q}{I b} τ = I b V Q ​

where:

V V V = internal transverse shear force at the cut section.

I I I = area moment of inertia of the entire cross-section about the neutral axis.

b b b = width of the cross-section at the specific depth y y y where shear stress is evaluated.

Q Q Q = first moment of area of the portion of the cross-section A ′ A' A ′ located above (or below) the level at which τ \tau τ is evaluated, relative to the neutral axis: Q = ∫ A ′ y d A = y ˉ ′ A ′ Q = \int_{A'} y \, dA = \bar{y}' A' Q = ∫ A ′ ​ y d A = y ˉ ​ ′ A ′

Here, y ˉ ′ \bar{y}' y ˉ ​ ′ represents the distance from the cross-section's neutral axis to the centroid of the sub-area A ′ A' A ′ . +-----------------+ --- y = c (extreme fiber: Q = 0, tau = 0)

  • | Area A' | |
  • +-----------------+ --- y1 (cut level: width = b, Q = y_bar' * A')
  • | | |
  • - -|- - - - - - - - -|- -|- - Neutral Axis (y = 0: Q_max, tau_max)
  • | |
  • +-----------------+
  • Shear Stress Distributions for Standard Sections
  • A. Solid Rectangular Cross-Section (Width b b b , Depth h h h )

For a rectangular section, I = b h 3 12 I = \frac{b h^3}{12} I = 12 b h 3 ​ . Evaluating Q ( y ) Q(y) Q ( y ) at a distance y y y from the neutral axis:

A ′ = b ( h 2 − y ) , y ˉ ′ = y + 1 2 ( h 2 − y ) = 1 2 ( h 2 + y ) A' = b \left(\frac{h}{2} - y\right), \quad \bar{y}' = y + \frac{1}{2}\left(\frac{h}{2} - y\right) = \frac{1}{2}\left(\frac{h}{2} + y\right) A ′ = b ( 2 h ​ − y ) , y ˉ ​ ′ = y + 2 1 ​ ( 2 h ​ − y ) = 2 1 ​ ( 2 h ​ + y )

Q ( y ) = y ˉ ′ A ′ = b 2 ( h 2 4 − y 2 ) Q(y) = \bar{y}' A' = \frac{b}{2} \left( \frac{h^2}{4} - y^2 \right) Q ( y ) = y ˉ ​ ′ A ′ = 2 b ​ ( 4 h 2 ​ − y 2 )

Substituting into the transverse shear formula:

τ ( y ) = V [ b 2 ( h 2 4 − y 2 ) ] ( b h 3 12 ) b = 3 V 2 b h ( 1 − 4 y 2 h 2 ) = 3 V 2 A ( 1 − 4 y 2 h 2 ) \tau(y) = \frac{V \left[ \frac{b}{2}\left(\frac{h^2}{4} - y^2\right) \right]}{\left(\frac{b h^3}{12}\right) b} = \frac{3 V}{2 b h} \left( 1 - \frac{4 y^2}{h^2} \right) = \frac{3 V}{2 A} \left( 1 - \frac{4 y^2}{h^2} \right) τ ( y ) = ( 12 b h 3 ​ ) b V [ 2 b ​ ( 4 h 2 ​ − y 2 ) ] ​ = 2 bh 3 V ​ ( 1 − h 2 4 y 2 ​ ) = 2 A 3 V ​ ( 1 − h 2 4 y 2 ​ )

At the outer free surfaces ( y = ± h / 2 y = \pm h/2 y = ± h /2 ): τ = 0 \tau = 0 τ = 0 .

At the neutral axis ( y = 0 y = 0 y = 0 ): shear stress reaches its parabolic maximum: τ max ⁡ = 1.5 V A = 3 V 2 A \tau_{\max} = 1.5 \frac{V}{A} = \frac{3 V}{2 A} τ m a x ​ = 1.5 A V ​ = 2 A 3 V ​

B. Solid Circular Cross-Section (Radius R R R , Diameter d d d )

For a solid circle, I = π R 4 4 I = \frac{\pi R^4}{4} I = 4 π R 4 ​ . At the neutral axis ( y = 0 y = 0 y = 0 ), A ′ A' A ′ is a semicircle of area π R 2 2 \frac{\pi R^2}{2} 2 π R 2 ​ , with centroid location y ˉ ′ = 4 R 3 π \bar{y}' = \frac{4 R}{3 \pi} y ˉ ​ ′ = 3 π 4 R ​ . The width at the neutral axis is b = 2 R = d b = 2 R = d b = 2 R = d . Evaluating Q Q Q :

Q max ⁡ = y ˉ ′ A ′ = ( 4 R 3 π ) ( π R 2 2 ) = 2 3 R 3 = d 3 12 Q_{\max} = \bar{y}' A' = \left(\frac{4 R}{3 \pi}\right) \left(\frac{\pi R^2}{2}\right) = \frac{2}{3} R^3 = \frac{d^3}{12} Q m a x ​ = y ˉ ​ ′ A ′ = ( 3 π 4 R ​ ) ( 2 π R 2 ​ ) = 3 2 ​ R 3 = 12 d 3 ​ τ max ⁡ = V Q max ⁡ I b = V ( 2 3 R 3 ) ( π R 4 4 ) ( 2 R ) = 4 V 3 π R 2 = 4 V 3 A ≈ 1.333 V A \tau_{\max} = \frac{V Q_{\max}}{I b} = \frac{V \left(\frac{2}{3} R^3\right)}{\left(\frac{\pi R^4}{4}\right)(2 R)} = \frac{4 V}{3 \pi R^2} = \frac{4 V}{3 A} \approx 1.333 \frac{V}{A} τ m a x ​ = I b V Q m a x ​ ​ = ( 4 π R 4 ​ ) ( 2 R ) V ( 3 2 ​ R 3 ) ​ = 3 π R 2 4 V ​ = 3 A 4 V ​ ≈ 1.333 A V ​

C. Wide-Flange (I-Beam) Sections & Shear in the Web

In standard structural W-shapes and I-beams:

Flanges have large width b f b_f b f ​ , resulting in negligible vertical shear stress ( τ = V Q / I b f \tau = VQ/Ib_f τ = V Q / I b f ​ ). Flanges carry > 85 − 90 % >85-90\% > 85 − 90% of bending moments.

The web has a thin width t w t_w t w ​ . Across the web, Q ( y ) Q(y) Q ( y ) remains large, causing the web to carry between 90% and 98% of the total vertical transverse shear force V V V .

In practical PE exam engineering design, average shear stress in the web is evaluated as: τ web, avg ≈ V d ⋅ t w \tau_{\text{web, avg}} \approx \frac{V}{d \cdot t_w} τ web, avg ​ ≈ d ⋅ t w ​ V ​

where d d d is overall beam depth and t w t_w t w ​ is web thickness.

Shear Flow in Built-Up Beams

For composite timber or steel beams fabricated with nails, bolts, or welds, shear flow q q q is defined as shear force per unit length: q = τ b = V Q I [ N/m or lb/in ] q = \tau b = \frac{V Q}{I} \quad [\text{N/m} \text{ or } \text{lb/in}] q = τ b = I V Q ​ [ N/m or lb/in ]

If fasteners have an allowable shear capacity V fastener V_{\text{fastener}} V fastener ​ and are installed with n n n fasteners across each transverse joint line, the required longitudinal pitch spacing s s s is: s = n ⋅ V fastener q = n ⋅ V fastener I V Q s = \frac{n \cdot V_{\text{fastener}}}{q} = \frac{n \cdot V_{\text{fastener}} I}{V Q} s = q n ⋅ V fastener ​ ​ = V Q n ⋅ V fastener ​ I ​

  • 3. Worked Example: Pin Joint and Built-Up Beam
  • Part A: Clevis Pin in Double Shear

A 12 mm 12\,\text{mm} 12 mm steel pin carries P = 20 kN P = 20\,\text{kN} P = 20 kN through a 10 mm 10\,\text{mm} 10 mm -thick tang held between two fork plates.

Pin shear (double shear, V = P / 2 V = P/2 V = P /2 on each plane): τ = 2 P π d 2 = 2 ( 20,000 ) π ( 12 ) 2 = 40,000 452.4 = 88.4 MPa \tau = \frac{2P}{\pi d^2} = \frac{2(20{,}000)}{\pi (12)^2} = \frac{40{,}000}{452.4} = 88.4\,\text{MPa} τ = π d 2 2 P ​ = π ( 12 ) 2 2 ( 20 , 000 ) ​ = 452.4 40 , 000 ​ = 88.4 MPa

Bearing on the tang (projected area d ⋅ t d \cdot t d ⋅ t ): σ b = P d t = 20,000 ( 12 ) ( 10 ) = 166.7 MPa \sigma_b = \frac{P}{d\,t} = \frac{20{,}000}{(12)(10)} = 166.7\,\text{MPa} σ b ​ = d t P ​ = ( 12 ) ( 10 ) 20 , 000 ​ = 166.7 MPa

If the same pin were loaded in single shear, the shear stress would double to 176.8 MPa 176.8\,\text{MPa} 176.8 MPa ; the bearing stress on the tang would not change.

Part B: Fastener Spacing in a Built-Up Beam

Two identical steel bars, each 100 mm 100\,\text{mm} 100 mm wide and 50 mm 50\,\text{mm} 50 mm deep, are stacked to form a 100 × 100 mm 100 \times 100\,\text{mm} 100 × 100 mm beam and joined by a single row of bolts along the interface. The maximum vertical shear is V = 10 kN V = 10\,\text{kN} V = 10 kN , and each bolt may carry V bolt = 6 kN V_{\text{bolt}} = 6\,\text{kN} V bolt ​ = 6 kN in shear.

Moment of inertia of the full section: I = b h 3 12 = 100 ( 100 ) 3 12 = 8.333 × 10 6 mm 4 I = \frac{b h^3}{12} = \frac{100 (100)^3}{12} = 8.333 \times 10^6\,\text{mm}^4 I = 12 b h 3 ​ = 12 100 ( 100 ) 3 ​ = 8.333 × 1 0 6 mm 4

First moment of the top bar about the neutral axis (the interface is the neutral axis): Q = A ′ y ˉ ′ = ( 100 × 50 ) ( 25 ) = 125,000 mm 3 Q = A' \bar{y}' = (100 \times 50)(25) = 125{,}000\,\text{mm}^3 Q = A ′ y ˉ ​ ′ = ( 100 × 50 ) ( 25 ) = 125 , 000 mm 3

Shear flow that the bolts must transfer: q = V Q I = ( 10,000 ) ( 125,000 ) 8.333 × 10 6 = 150 N/mm q = \frac{V Q}{I} = \frac{(10{,}000)(125{,}000)}{8.333 \times 10^6} = 150\,\text{N/mm} q = I V Q ​ = 8.333 × 1 0 6 ( 10 , 000 ) ( 125 , 000 ) ​ = 150 N/mm

Maximum bolt pitch with one bolt per row ( n = 1 n = 1 n = 1 ): s = n V bolt q = 6,000 150 = 40 mm s = \frac{n V_{\text{bolt}}}{q} = \frac{6{,}000}{150} = 40\,\text{mm} s = q n V bolt ​ ​ = 150 6 , 000 ​ = 40 mm

Check: the peak transverse shear stress in the solid section is τ max ⁡ = 1.5 V / A = 1.5 ( 10,000 ) / 10,000 = 1.5 MPa \tau_{\max} = 1.5 V/A = 1.5(10{,}000)/10{,}000 = 1.5\,\text{MPa} τ m a x ​ = 1.5 V / A = 1.5 ( 10 , 000 ) /10 , 000 = 1.5 MPa , the same value V Q / ( I b ) V Q/(I b) V Q / ( I b ) gives at the interface. The bolts, not the steel, govern this joint.

Tip

Shear flow is largest where V V V is largest, so built-up beams often use closer fastener spacing near the supports and wider spacing near midspan, where shear is small.