Study guide

3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes

PE Mechanical: Machine Design and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology

1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety

2 Chapter 2: Physical & Mechanical Properties of Engineering Materials

2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep

3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections

3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis

4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects

4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses

5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics

5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics

6 Chapter 6: Fatigue Analysis & Dynamic Failure

6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage

7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints

7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors

8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding

8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding

9 Chapter 9: Power Transmission: Shafts & Gearing

9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing

10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers

10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels

11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods

12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power

12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics

13 Chapter 13: Kinematics, Mechatronics & Control Systems

13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls

14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods

14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly

15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion

15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement

3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes

Key Takeaways Explain This Topic AI

Elastic torsion of circular shafts produces shear stress τ = T r J \tau = \frac{Tr}{J} τ = J T r ​ and angle of twist ϕ = T L G J \phi = \frac{TL}{GJ} ϕ = G J T L ​ ; hollow shafts provide substantial weight savings by concentrating material at maximum radial distance.

Closed thin-walled non-circular tubes develop constant shear flow q = τ t q = \tau t q = τ t around their perimeter, governed by the Bredt-Batho relation τ = T 2 A m t \tau = \frac{T}{2 A_m t} τ = 2 A m ​ t T ​ .

Power links torque and speed: T = 63,025 h p / n T = 63{,}025\,hp/n T = 63 , 025 h p / n (in-lb), T = 5,252 h p / n T = 5{,}252\,hp/n T = 5 , 252 h p / n (ft-lb), and T = 9,549 P / n T = 9{,}549\,P/n T = 9 , 549 P / n (N·m with P P P in kW).

Angle-of-twist limits often govern shaft size: in the worked example a 1 ∘ 1^\circ 1 ∘ limit required 45.5 mm 45.5\text{ mm} 45.5 mm versus 36.5 mm 36.5\text{ mm} 36.5 mm for stress, and a hollow shaft with d i / d o = 0.75 d_i/d_o = 0.75 d i ​ / d o ​ = 0.75 saved 47% of the mass.

Last updated: October 2026

3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes

A twisting moment applied about a member's longitudinal axis produces torsional shear stress . Transmission shafts, couplings, torque tubes, spring wire and drive axles are all sized with the relations below, and on the exam a torsion check almost always comes paired with a power-and-speed conversion and an angle-of-twist (stiffness) limit.

1. Torsion of Circular Solid & Hollow Shafts

Torsion refers to the twisting of a structural member when subjected to an applied moment acting about its longitudinal axis. In circular cross-sections (solid or hollow), axisymmetric geometry ensures that plane cross-sections remain plane and do not warp during elastic twisting.

The Elastic Torsion Formula

Torsional shear stress τ \tau τ increases linearly with radial distance r r r from the shaft centerline: τ ( r ) = T r J \tau(r) = \frac{T r}{J} τ ( r ) = J T r ​

Maximum shear stress develops at the outermost boundary radius c = r o = d o / 2 c = r_o = d_o / 2 c = r o ​ = d o ​ /2 : τ max ⁡ = T c J = T d o / 2 J \tau_{\max} = \frac{T c}{J} = \frac{T d_o / 2}{J} τ m a x ​ = J T c ​ = J T d o ​ /2 ​

Polar Moment of Inertia ( J J J )

Solid Circular Shaft (Diameter d d d ): J = π d 4 32 = π r 4 2 J = \frac{\pi d^4}{32} = \frac{\pi r^4}{2} J = 32 π d 4 ​ = 2 π r 4 ​ τ max ⁡ = T ( d / 2 ) π d 4 32 = 16 T π d 3 \tau_{\max} = \frac{T (d/2)}{\frac{\pi d^4}{32}} = \frac{16 T}{\pi d^3} τ m a x ​ = 32 π d 4 ​ T ( d /2 ) ​ = π d 3 16 T ​

Hollow Circular Shaft (Outer Dia d o d_o d o ​ , Inner Dia d i d_i d i ​ ): J = π ( d o 4 − d i 4 ) 32 = π ( r o 4 − r i 4 ) 2 J = \frac{\pi (d_o^4 - d_i^4)}{32} = \frac{\pi (r_o^4 - r_i^4)}{2} J = 32 π ( d o 4 ​ − d i 4 ​ ) ​ = 2 π ( r o 4 ​ − r i 4 ​ ) ​ τ max ⁡ = T ( d o / 2 ) π ( d o 4 − d i 4 ) 32 = 16 T d o π ( d o 4 − d i 4 ) \tau_{\max} = \frac{T (d_o / 2)}{\frac{\pi (d_o^4 - d_i^4)}{32}} = \frac{16 T d_o}{\pi (d_o^4 - d_i^4)} τ m a x ​ = 32 π ( d o 4 ​ − d i 4 ​ ) ​ T ( d o ​ /2 ) ​ = π ( d o 4 ​ − d i 4 ​ ) 16 T d o ​ ​

Angle of Twist ( ϕ \phi ϕ )

The total angle of twist ϕ \phi ϕ in radians over length L L L for a shaft of uniform shear modulus G G G is: ϕ = T L G J [ radians ] \phi = \frac{T L}{G J} \quad [\text{radians}] ϕ = G J T L ​ [ radians ]

To convert radians to degrees: ϕ deg = ϕ rad ( 180 ∘ π ) \phi_{\text{deg}} = \phi_{\text{rad}} \left(\frac{180^\circ}{\pi}\right) ϕ deg ​ = ϕ rad ​ ( π 18 0 ∘ ​ ) . Torsional stiffness k t k_t k t ​ is: k t = T ϕ = G J L [ N ⋅ m/rad or in-lb/rad ] k_t = \frac{T}{\phi} = \frac{G J}{L} \quad [\text{N}\cdot\text{m/rad} \text{ or } \text{in-lb/rad}] k t ​ = ϕ T ​ = L G J ​ [ N ⋅ m/rad or in-lb/rad ]

2. Torsional Power Transmission: SI & USCS Units

Rotating shafts are ubiquitous in machine systems for transmitting mechanical power between motors, gearboxes, and driven loads. Mechanical power P P P is the product of applied torque T T T and angular velocity ω \omega ω : P = T ω = 2 π N T / 60 P = T \omega = 2 \pi N T / 60 P = T ω = 2 π NT /60

where N N N is rotational shaft speed in revolutions per minute (rpm) and ω = 2 π N 60 \omega = \frac{2 \pi N}{60} ω = 60 2 π N ​ in rad/s.

SI Unit Formulation

Power P P P in Watts (W) or kilowatts (kW).

Torque T T T in Newton-meters ( N ⋅ m \text{N}\cdot\text{m} N ⋅ m ).

Speed N N N in rpm. T = P ω = 60 P 2 π N ≈ 9.5493 ( P N ) T = \frac{P}{\omega} = \frac{60 P}{2 \pi N} \approx 9.5493 \left(\frac{P}{N}\right) T = ω P ​ = 2 π N 60 P ​ ≈ 9.5493 ( N P ​ )

(Note: When P P P is in kW, multiply by 10 3 10^3 1 0 3 to obtain T T T in N ⋅ m \text{N}\cdot\text{m} N ⋅ m ) .

USCS Unit Formulation

Power in horsepower (hp), where 1 hp = 550 ft-lb/s = 6600 in-lb/s = 33 , 000 ft-lb/min 1\text{ hp} = 550\text{ ft-lb/s} = 6600\text{ in-lb/s} = 33,000\text{ ft-lb/min} 1 hp = 550 ft-lb/s = 6600 in-lb/s = 33 , 000 ft-lb/min .

Rotational speed n n n in rpm.

Torque in inch-pounds ( T T T in in-lb \text{in-lb} in-lb ): hp = T in-lb ⋅ n 63 , 025 ⟺ T in-lb = 63 , 025 ⋅ hp n \text{hp} = \frac{T_{\text{in-lb}} \cdot n}{63,025} \iff T_{\text{in-lb}} = \frac{63,025 \cdot \text{hp}}{n} hp = 63 , 025 T in-lb ​ ⋅ n ​ ⟺ T in-lb ​ = n 63 , 025 ⋅ hp ​

Torque in foot-pounds ( T T T in ft-lb \text{ft-lb} ft-lb ): hp = T ft-lb ⋅ n 5252 ⟺ T ft-lb = 5252 ⋅ hp n \text{hp} = \frac{T_{\text{ft-lb}} \cdot n}{5252} \iff T_{\text{ft-lb}} = \frac{5252 \cdot \text{hp}}{n} hp = 5252 T ft-lb ​ ⋅ n ​ ⟺ T ft-lb ​ = n 5252 ⋅ hp ​

3. Thin-Walled Non-Circular Closed Tubes (Bredt-Batho Theory)

Non-circular sections (rectangles, ellipses, streamline tubes) undergo significant cross-sectional warping under torsion, invalidating the classic circular torsion formula. However, for thin-walled closed tubes with wall thickness t ≪ t \ll t ≪ overall dimensions, shear flow q = τ t q = \tau t q = τ t is constant around the entire perimeter. +---------------------------+

  • | Mean Centerline Area Am |
  • | +-------------------+ |
  • | t | | |
  • | +-------------------+ |
  • +---------------------------+
  • Bredt-Batho Shear Stress Formula τ = T 2 A m t \tau = \frac{T}{2 A_m t} τ = 2 A m ​ t T ​

where A m A_m A m ​ is the cross-sectional area enclosed by the median line (mean centerline) of the tube wall, and t t t is the local wall thickness at the point of interest.

Angle of Twist for Closed Thin-Walled Tubes

The rate of twist θ = ϕ / L \theta = \phi / L θ = ϕ / L is obtained by integrating along the median perimeter S m S_m S m ​ : θ = T 4 A m 2 G ∮ d s t \theta = \frac{T}{4 A_m^2 G} \oint \frac{ds}{t} θ = 4 A m 2 ​ G T ​ ∮ t d s ​

For a tube with constant wall thickness t t t and total median perimeter length S m S_m S m ​ : ϕ = T L S m 4 A m 2 G t \phi = \frac{T L S_m}{4 A_m^2 G t} ϕ = 4 A m 2 ​ Gt T L S m ​ ​

Open vs. Closed Sections: A closed tubular section exhibits immense torsional stiffness. If a longitudinal slit is cut along the tube wall, it becomes an open thin-walled section. Its torsional stiffness drops by factors of 100 100 100 to 10 , 000 × 10,000\times 10 , 000 × , and peak shear stress escalates dramatically because shear must circulate within the narrow thickness ( J open ≈ 1 3 ∑ b i t i 3 J_{\text{open}} \approx \frac{1}{3} \sum b_i t_i^3 J open ​ ≈ 3 1 ​ ∑ b i ​ t i 3 ​ ).

  • 4. Worked Step-by-Step Shaft Sizing Example
  • Problem Statement

A solid drive shaft is required to transmit P = 45 kW P = 45\text{ kW} P = 45 kW of continuous power from an electric motor operating at a rated speed of N = 900 rpm N = 900\text{ rpm} N = 900 rpm . The shaft span between bearings is L = 1.20 m L = 1.20\text{ m} L = 1.20 m .

Design Constraints & Material Properties:

Material: Cold-rolled AISI 1045 steel.

Allowable shear stress: τ allow = 50 MPa \tau_{\text{allow}} = 50\text{ MPa} τ allow ​ = 50 MPa .

Allowable angle of twist: ϕ allow = 1.0 ∘ \phi_{\text{allow}} = 1.0^\circ ϕ allow ​ = 1. 0 ∘ over the total 1.20 m 1.20\text{ m} 1.20 m span.

Shear modulus: G = 78 GPa = 78 × 10 9 Pa G = 78\text{ GPa} = 78 \times 10^9\text{ Pa} G = 78 GPa = 78 × 1 0 9 Pa .

Objective:

Calculate the steady-state operating torque T T T .

Determine the minimum required shaft diameter d solid d_{\text{solid}} d solid ​ satisfying both strength and torsional stiffness.

Compare a hollow shaft design with d i / d o = 0.75 d_i / d_o = 0.75 d i ​ / d o ​ = 0.75 , evaluating the required outer diameter and percentage mass savings.

Step 1: Operating Torque Calculation

Convert power to Watts ( P = 45 , 000 W P = 45,000\text{ W} P = 45 , 000 W ) and calculate angular velocity ω \omega ω :

ω = 2 π N 60 = 2 π ( 900 ) 60 = 30 π ≈ 94.2478 rad/s \omega = \frac{2 \pi N}{60} = \frac{2 \pi (900)}{60} = 30 \pi \approx 94.2478\text{ rad/s} ω = 60 2 π N ​ = 60 2 π ( 900 ) ​ = 30 π ≈ 94.2478 rad/s

T = P ω = 45 , 000 W 94.2478 rad/s = 477.465 N ⋅ m T = \frac{P}{\omega} = \frac{45,000\text{ W}}{94.2478\text{ rad/s}} = 477.465\text{ N}\cdot\text{m} T = ω P ​ = 94.2478 rad/s 45 , 000 W ​ = 477.465 N ⋅ m

Step 2: Sizing Solid Shaft for Strength (Stress Criterion)

Applying the elastic torsion formula for a solid circular shaft:

τ max ⁡ = 16 T π d 3 ≤ τ allow \tau_{\max} = \frac{16 T}{\pi d^3} \le \tau_{\text{allow}} τ m a x ​ = π d 3 16 T ​ ≤ τ allow ​

d ≥ ( 16 T π τ allow ) 1 / 3 = ( 16 × 477.465 N ⋅ m π × 50 × 10 6 N/m 2 ) 1 / 3 d \ge \left( \frac{16 T}{\pi \tau_{\text{allow}}} \right)^{1/3} = \left( \frac{16 \times 477.465\text{ N}\cdot\text{m}}{\pi \times 50 \times 10^6\text{ N/m}^2} \right)^{1/3} d ≥ ( π τ allow ​ 16 T ​ ) 1/3 = ( π × 50 × 1 0 6 N/m 2 16 × 477.465 N ⋅ m ​ ) 1/3

d ≥ ( 7639.44 1.57080 × 10 8 ) 1 / 3 = ( 4.86341 × 10 − 5 m 3 ) 1 / 3 = 0.03650 m = 36.50 mm d \ge \left( \frac{7639.44}{1.57080 \times 10^8} \right)^{1/3} = (4.86341 \times 10^{-5}\text{ m}^3)^{1/3} = 0.03650\text{ m} = 36.50\text{ mm} d ≥ ( 1.57080 × 1 0 8 7639.44 ​ ) 1/3 = ( 4.86341 × 1 0 − 5 m 3 ) 1/3 = 0.03650 m = 36.50 mm

Step 3: Sizing Solid Shaft for Stiffness (Twist Criterion)

First, convert allowable twist from degrees to radians:

ϕ allow = 1.0 ∘ × ( π 180 ∘ ) = 0.0174533 radians \phi_{\text{allow}} = 1.0^\circ \times \left(\frac{\pi}{180^\circ}\right) = 0.0174533\text{ radians} ϕ allow ​ = 1. 0 ∘ × ( 18 0 ∘ π ​ ) = 0.0174533 radians

Using the angle of twist formula for a solid shaft ( J = π d 4 / 32 J = \pi d^4 / 32 J = π d 4 /32 ):

ϕ = T L G J = 32 T L π G d 4 ≤ ϕ allow \phi = \frac{T L}{G J} = \frac{32 T L}{\pi G d^4} \le \phi_{\text{allow}} ϕ = G J T L ​ = π G d 4 32 T L ​ ≤ ϕ allow ​

d ≥ ( 32 T L π G ϕ allow ) 1 / 4 = ( 32 × 477.465 N ⋅ m × 1.20 m π × ( 78 × 10 9 Pa ) × 0.0174533 rad ) 1 / 4 d \ge \left( \frac{32 T L}{\pi G \phi_{\text{allow}}} \right)^{1/4} = \left( \frac{32 \times 477.465\text{ N}\cdot\text{m} \times 1.20\text{ m}}{\pi \times (78 \times 10^9\text{ Pa}) \times 0.0174533\text{ rad}} \right)^{1/4} d ≥ ( π G ϕ allow ​ 32 T L ​ ) 1/4 = ( π × ( 78 × 1 0 9 Pa ) × 0.0174533 rad 32 × 477.465 N ⋅ m × 1.20 m ​ ) 1/4

Numerator: 32 × 477.465 × 1.20 = 18 , 334.66 N ⋅ m 2 32 \times 477.465 \times 1.20 = 18,334.66\text{ N}\cdot\text{m}^2 32 × 477.465 × 1.20 = 18 , 334.66 N ⋅ m 2 .

Denominator: π × ( 78 × 10 9 ) × 0.0174533 = 4.27683 × 10 9 N/m 2 \pi \times (78 \times 10^9) \times 0.0174533 = 4.27683 \times 10^9\text{ N/m}^2 π × ( 78 × 1 0 9 ) × 0.0174533 = 4.27683 × 1 0 9 N/m 2 .

d ≥ ( 18 , 334.66 4.27683 × 10 9 ) 1 / 4 = ( 4.28697 × 10 − 6 m 4 ) 1 / 4 = 0.04550 m = 45.50 mm d \ge \left( \frac{18,334.66}{4.27683 \times 10^9} \right)^{1/4} = (4.28697 \times 10^{-6}\text{ m}^4)^{1/4} = 0.04550\text{ m} = 45.50\text{ mm} d ≥ ( 4.27683 × 1 0 9 18 , 334.66 ​ ) 1/4 = ( 4.28697 × 1 0 − 6 m 4 ) 1/4 = 0.04550 m = 45.50 mm

Criterion Comparison:

Strength requirement: d ≥ 36.50 mm d \ge 36.50\text{ mm} d ≥ 36.50 mm .

Stiffness requirement: d ≥ 45.50 mm d \ge 45.50\text{ mm} d ≥ 45.50 mm .

Governing Design: Torsional stiffness governs. Sizing requires d min = 45.50 mm d_{\text{min}} = 45.50\text{ mm} d min ​ = 45.50 mm . Sizing to the nearest standard millimetric increment yields d = 46 mm d = 46\text{ mm} d = 46 mm or d = 48 mm d = 48\text{ mm} d = 48 mm .

Step 4: Hollow Shaft Design & Mass Reduction Analysis

Let the hollow shaft have an inner-to-outer diameter ratio c r = d i / d o = 0.75 c_r = d_i / d_o = 0.75 c r ​ = d i ​ / d o ​ = 0.75 .

The polar moment of inertia is:

J hollow = π d o 4 32 ( 1 − c r 4 ) = π d o 4 32 [ 1 − ( 0.75 ) 4 ] = π d o 4 32 [ 1 − 0.316406 ] = 0.683594 ( π d o 4 32 ) J_{\text{hollow}} = \frac{\pi d_o^4}{32} (1 - c_r^4) = \frac{\pi d_o^4}{32} [1 - (0.75)^4] = \frac{\pi d_o^4}{32} [1 - 0.316406] = 0.683594 \left(\frac{\pi d_o^4}{32}\right) J hollow ​ = 32 π d o 4 ​ ​ ( 1 − c r 4 ​ ) = 32 π d o 4 ​ ​ [ 1 − ( 0.75 ) 4 ] = 32 π d o 4 ​ ​ [ 1 − 0.316406 ] = 0.683594 ( 32 π d o 4 ​ ​ )

For identical torsional stiffness, J hollow = J solid = π d solid 4 32 J_{\text{hollow}} = J_{\text{solid}} = \frac{\pi d_{\text{solid}}^4}{32} J hollow ​ = J solid ​ = 32 π d solid 4 ​ ​ :

d o 4 ( 0.683594 ) = d solid 4 ⟹ d o = d solid ( 0.683594 ) 1 / 4 = 45.50 mm 0.90928 = 50.04 mm d_o^4 (0.683594) = d_{\text{solid}}^4 \implies d_o = \frac{d_{\text{solid}}}{(0.683594)^{1/4}} = \frac{45.50\text{ mm}}{0.90928} = 50.04\text{ mm} d o 4 ​ ( 0.683594 ) = d solid 4 ​ ⟹ d o ​ = ( 0.683594 ) 1/4 d solid ​ ​ = 0.90928 45.50 mm ​ = 50.04 mm

d i = 0.75 × 50.04 mm = 37.53 mm d_i = 0.75 \times 50.04\text{ mm} = 37.53\text{ mm} d i ​ = 0.75 × 50.04 mm = 37.53 mm

Now, compare cross-sectional areas to evaluate mass reduction:

A solid = π d solid 2 4 = π ( 45.50 mm ) 2 4 = 1626.0 mm 2 A_{\text{solid}} = \frac{\pi d_{\text{solid}}^2}{4} = \frac{\pi (45.50\text{ mm})^2}{4} = 1626.0\text{ mm}^2 A solid ​ = 4 π d solid 2 ​ ​ = 4 π ( 45.50 mm ) 2 ​ = 1626.0 mm 2

A hollow = π ( d o 2 − d i 2 ) 4 = π [ ( 50.04 ) 2 − ( 37.53 ) 2 ] 4 = π [ 2504.00 − 1408.50 ] 4 = π ( 1095.50 ) 4 = 860.4 mm 2 A_{\text{hollow}} = \frac{\pi (d_o^2 - d_i^2)}{4} = \frac{\pi [(50.04)^2 - (37.53)^2]}{4} = \frac{\pi [2504.00 - 1408.50]}{4} = \frac{\pi (1095.50)}{4} = 860.4\text{ mm}^2 A hollow ​ = 4 π ( d o 2 ​ − d i 2 ​ ) ​ = 4 π [( 50.04 ) 2 − ( 37.53 ) 2 ] ​ = 4 π [ 2504.00 − 1408.50 ] ​ = 4 π ( 1095.50 ) ​ = 860.4 mm 2

Mass Savings = A solid − A hollow A solid × 100 % = 1626.0 − 860.4 1626.0 × 100 % = 47.08 % \text{Mass Savings} = \frac{A_{\text{solid}} - A_{\text{hollow}}}{A_{\text{solid}}} \times 100\% = \frac{1626.0 - 860.4}{1626.0} \times 100\% = 47.08\% Mass Savings = A solid ​ A solid ​ − A hollow ​ ​ × 100% = 1626.0 1626.0 − 860.4 ​ × 100% = 47.08%

Conclusion: By replacing the solid shaft with a hollow shaft ( d o = 50.0 mm , d i = 37.5 mm d_o = 50.0\text{ mm}, d_i = 37.5\text{ mm} d o ​ = 50.0 mm , d i ​ = 37.5 mm ), the mass is reduced by 47.1% while providing exactly identical torsional rigidity.