Study guide

4.2 Combined Loading, Principal Stresses & Mohr's Circle

PE Mechanical: Machine Design and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology

1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety

2 Chapter 2: Physical & Mechanical Properties of Engineering Materials

2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep

3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections

3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis

4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects

4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses

5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics

5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics

6 Chapter 6: Fatigue Analysis & Dynamic Failure

6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage

7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints

7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors

8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding

8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding

9 Chapter 9: Power Transmission: Shafts & Gearing

9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing

10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers

10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels

11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods

12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power

12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics

13 Chapter 13: Kinematics, Mechatronics & Control Systems

13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls

14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods

14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly

15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion

15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement

4.2 Combined Loading, Principal Stresses & Mohr's Circle

Key Takeaways Explain This Topic AI

General plane stress states combine normal stresses ( σ x , σ y \sigma_x, \sigma_y σ x ​ , σ y ​ ) and shear stress ( τ x y \tau_{xy} τ x y ​ ), which transform under coordinate rotation θ \theta θ following equilibrium relationships that describe a circle in ( σ , τ ) (\sigma, \tau) ( σ , τ ) space.

The principal normal stresses σ 1 , σ 2 = σ x + σ y 2 ± ( σ x − σ y 2 ) 2 + τ x y 2 \sigma_1, \sigma_2 = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} σ 1 ​ , σ 2 ​ = 2 σ x ​ + σ y ​ ​ ± ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​ act on mutually perpendicular planes oriented at 2 θ p = arctan ⁡ ( 2 τ x y σ x − σ y ) 2\theta_p = \arctan\left(\frac{2\tau_{xy}}{\sigma_x - \sigma_y}\right) 2 θ p ​ = arctan ( σ x ​ − σ y ​ 2 τ x y ​ ​ ) , where shear stress is identically zero.

Maximum in-plane shear stress τ max ⁡ , i n = R = ( σ x − σ y 2 ) 2 + τ x y 2 \tau_{\max, in} = R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} τ m a x , in ​ = R = ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​ acts on planes oriented 45 ∘ 45^\circ 4 5 ∘ from the principal planes and coexists with an average normal stress σ avg = σ x + σ y 2 \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} σ avg ​ = 2 σ x ​ + σ y ​ ​ .

The absolute maximum shear stress τ max ⁡ , a b s = σ I − σ I I I 2 \tau_{\max, abs} = \frac{\sigma_I - \sigma_{III}}{2} τ m a x , ab s ​ = 2 σ I ​ − σ III ​ ​ requires ranking all three principal stresses (including σ 3 = 0 \sigma_3 = 0 σ 3 ​ = 0 in plane stress); if σ 1 \sigma_1 σ 1 ​ and σ 2 \sigma_2 σ 2 ​ have identical signs, τ max ⁡ , a b s = max ⁡ ( ∣ σ 1 ∣ , ∣ σ 2 ∣ ) 2 \tau_{\max, abs} = \frac{\max(|\sigma_1|, |\sigma_2|)}{2} τ m a x , ab s ​ = 2 m a x ( ∣ σ 1 ​ ∣ , ∣ σ 2 ​ ∣ ) ​ , which governs ductile yield criteria (Tresca).

Strain rosettes ( 45 ∘ 45^\circ 4 5 ∘ rectangular and 60 ∘ 60^\circ 6 0 ∘ delta) measure three directional normal surface strains to calculate the complete in-plane strain tensor ( ϵ x , ϵ y , γ x y ) (\epsilon_x, \epsilon_y, \gamma_{xy}) ( ϵ x ​ , ϵ y ​ , γ x y ​ ) , which converts to stresses via 3D generalized Hooke's law.

Last updated: October 2026

4.2 Combined Loading, Principal Stresses & Mohr's Circle

Mechanical components—such as power transmission shafts, pressure vessel walls, turbine rotors, and machine frames—rarely operate under simple uniaxial tension or pure torsion. Instead, external forces, bending moments, torques, and internal pressures combine to produce complex multiaxial states of stress. Determining structural integrity requires transforming these combined stress components onto principal planes to calculate maximum normal stresses, maximum in-plane shear, and absolute maximum shear stress.

3D Stress Tensor & The Plane Stress Condition

The general three-dimensional stress state acting on an infinitesimal cubic element is represented by the symmetric Cauchy stress tensor σ \boldsymbol{\sigma} σ : σ = [ σ x τ x y τ x z τ y x σ y τ y z τ z x τ z y σ z ] \boldsymbol{\sigma} = \begin{bmatrix} \sigma_x & \tau_{xy} & \tau_{xz} \\ \tau_{yx} & \sigma_y & \tau_{yz} \\ \tau_{zx} & \tau_{zy} & \sigma_z \end{bmatrix} σ = ​ σ x ​ τ y x ​ τ z x ​ ​ τ x y ​ σ y ​ τ zy ​ ​ τ x z ​ τ yz ​ σ z ​ ​ ​

Moment equilibrium about the coordinate axes requires shear stress symmetry: τ x y = τ y x \tau_{xy} = \tau_{yx} τ x y ​ = τ y x ​ , τ x z = τ z x \tau_{xz} = \tau_{zx} τ x z ​ = τ z x ​ , and τ y z = τ z y \tau_{yz} = \tau_{zy} τ yz ​ = τ zy ​ , reducing the tensor to six independent stress components.

In many critical engineering applications—including thin plates, structural shells, and free external surfaces of solid bodies—the out-of-plane normal and shear stresses vanish: σ z = 0 , τ x z = 0 , τ y z = 0 \sigma_z = 0, \quad \tau_{xz} = 0, \quad \tau_{yz} = 0 σ z ​ = 0 , τ x z ​ = 0 , τ yz ​ = 0

This condition is defined as plane stress . The in-plane state is fully characterized by normal stresses σ x \sigma_x σ x ​ , σ y \sigma_y σ y ​ , and shear stress τ x y \tau_{xy} τ x y ​ .

Plane Stress Transformation Equations

Consider an inclined plane cutting through the stress element at an angle θ \theta θ , measured counterclockwise positive from the positive x x x -axis. Projecting force equilibrium along the rotated axis x ′ x' x ′ (normal to the inclined plane) and y ′ y' y ′ (tangential to the plane) yields the fundamental analytical transformation equations: σ x ′ = σ x + σ y 2 + σ x − σ y 2 cos ⁡ 2 θ + τ x y sin ⁡ 2 θ \sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \frac{\sigma_x - \sigma_y}{2} \cos 2\theta + \tau_{xy} \sin 2\theta σ x ′ ​ = 2 σ x ​ + σ y ​ ​ + 2 σ x ​ − σ y ​ ​ cos 2 θ + τ x y ​ sin 2 θ σ y ′ = σ x + σ y 2 − σ x − σ y 2 cos ⁡ 2 θ − τ x y sin ⁡ 2 θ \sigma_{y'} = \frac{\sigma_x + \sigma_y}{2} - \frac{\sigma_x - \sigma_y}{2} \cos 2\theta - \tau_{xy} \sin 2\theta σ y ′ ​ = 2 σ x ​ + σ y ​ ​ − 2 σ x ​ − σ y ​ ​ cos 2 θ − τ x y ​ sin 2 θ τ x ′ y ′ = − σ x − σ y 2 sin ⁡ 2 θ + τ x y cos ⁡ 2 θ \tau_{x'y'} = -\frac{\sigma_x - \sigma_y}{2} \sin 2\theta + \tau_{xy} \cos 2\theta τ x ′ y ′ ​ = − 2 σ x ​ − σ y ​ ​ sin 2 θ + τ x y ​ cos 2 θ

An essential mathematical property of stress transformation is the invariance of the sum of orthogonal normal stresses: I 1 = σ x ′ + σ y ′ = σ x + σ y I_1 = \sigma_{x'} + \sigma_{y'} = \sigma_x + \sigma_y I 1 ​ = σ x ′ ​ + σ y ′ ​ = σ x ​ + σ y ​

The first stress invariant I 1 I_1 I 1 ​ remains constant under any arbitrary coordinate rotation.

Principal Stresses and Principal Planes

The planes on which maximum and minimum normal stresses act are called the principal planes . Differentiating σ x ′ \sigma_{x'} σ x ′ ​ with respect to θ \theta θ and setting the derivative to zero (or equivalently setting τ x ′ y ′ = 0 \tau_{x'y'} = 0 τ x ′ y ′ ​ = 0 ) gives the principal orientation angle θ p \theta_p θ p ​ : tan ⁡ 2 θ p = 2 τ x y σ x − σ y \tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y} tan 2 θ p ​ = σ x ​ − σ y ​ 2 τ x y ​ ​

This relationship defines two mutually perpendicular angles, θ p 1 \theta_{p1} θ p 1 ​ and θ p 2 = θ p 1 + 90 ∘ \theta_{p2} = \theta_{p1} + 90^\circ θ p 2 ​ = θ p 1 ​ + 9 0 ∘ . Substituting these angles back into the normal stress transformation equation yields the principal normal stresses σ 1 \sigma_1 σ 1 ​ and σ 2 \sigma_2 σ 2 ​ : σ 1 , σ 2 = σ x + σ y 2 ± ( σ x − σ y 2 ) 2 + τ x y 2 \sigma_1, \sigma_2 = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} σ 1 ​ , σ 2 ​ = 2 σ x ​ + σ y ​ ​ ± ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​

By standard convention, σ 1 ≥ σ 2 \sigma_1 \ge \sigma_2 σ 1 ​ ≥ σ 2 ​ .

Important

On principal planes, shear stresses are identically zero ( τ = 0 \tau = 0 τ = 0 ). Any plane that exhibits non-zero shear stress cannot be a principal plane.

  • Maximum In-Plane vs. Absolute Maximum Shear Stress
  • Maximum In-Plane Shear Stress

The maximum in-plane shear stress τ max ⁡ , i n \tau_{\max, in} τ m a x , in ​ acts on planes rotated 45 ∘ 45^\circ 4 5 ∘ from the principal planes. Differentiating τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ ​ with respect to θ \theta θ and setting it to zero gives: tan ⁡ 2 θ s = − σ x − σ y 2 τ x y = − 1 tan ⁡ 2 θ p \tan 2\theta_s = -\frac{\sigma_x - \sigma_y}{2 \tau_{xy}} = -\frac{1}{\tan 2\theta_p} tan 2 θ s ​ = − 2 τ x y ​ σ x ​ − σ y ​ ​ = − tan 2 θ p ​ 1 ​

Because the slopes of 2 θ s 2\theta_s 2 θ s ​ and 2 θ p 2\theta_p 2 θ p ​ are negative reciprocals, 2 θ s = 2 θ p ± 90 ∘ 2\theta_s = 2\theta_p \pm 90^\circ 2 θ s ​ = 2 θ p ​ ± 9 0 ∘ , confirming that θ s = θ p ± 45 ∘ \theta_s = \theta_p \pm 45^\circ θ s ​ = θ p ​ ± 4 5 ∘ .

The magnitude of the maximum in-plane shear stress equals the radius of Mohr's circle: τ max ⁡ , i n = ( σ x − σ y 2 ) 2 + τ x y 2 = σ 1 − σ 2 2 \tau_{\max, in} = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} = \frac{\sigma_1 - \sigma_2}{2} τ m a x , in ​ = ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​ = 2 σ 1 ​ − σ 2 ​ ​

Planes of maximum in-plane shear stress are not normal-stress-free; they carry an average normal stress: σ avg = σ x + σ y 2 = σ 1 + σ 2 2 \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} = \frac{\sigma_1 + \sigma_2}{2} σ avg ​ = 2 σ x ​ + σ y ​ ​ = 2 σ 1 ​ + σ 2 ​ ​

Absolute Maximum Shear Stress ( τ max ⁡ , a b s \tau_{\max, abs} τ m a x , ab s ​ )

Engineering materials fail in three dimensions. To calculate the true worst-case shear stress, all three principal stresses must be ranked algebraically: σ I ≥ σ I I ≥ σ I I I \sigma_I \ge \sigma_{II} \ge \sigma_{III} σ I ​ ≥ σ II ​ ≥ σ III ​

The absolute maximum shear stress is given by: τ max ⁡ , a b s = σ I − σ I I I 2 \tau_{\max, abs} = \frac{\sigma_I - \sigma_{III}}{2} τ m a x , ab s ​ = 2 σ I ​ − σ III ​ ​

In a plane stress state, the third out-of-plane principal stress is σ z = 0 \sigma_z = 0 σ z ​ = 0 . The relationship between τ max ⁡ , i n \tau_{\max, in} τ m a x , in ​ and τ max ⁡ , a b s \tau_{\max, abs} τ m a x , ab s ​ depends on the algebraic signs of σ 1 \sigma_1 σ 1 ​ and σ 2 \sigma_2 σ 2 ​ :

Opposite Signs ( σ 1 > 0 \sigma_1 > 0 σ 1 ​ > 0 and σ 2 < 0 \sigma_2 < 0 σ 2 ​ < 0 ) : σ I = σ 1 , σ I I = 0 , σ I I I = σ 2 \sigma_I = \sigma_1, \quad \sigma_{II} = 0, \quad \sigma_{III} = \sigma_2 σ I ​ = σ 1 ​ , σ II ​ = 0 , σ III ​ = σ 2 ​ τ max ⁡ , a b s = σ 1 − σ 2 2 = τ max ⁡ , i n \tau_{\max, abs} = \frac{\sigma_1 - \sigma_2}{2} = \tau_{\max, in} τ m a x , ab s ​ = 2 σ 1 ​ − σ 2 ​ ​ = τ m a x , in ​

Both Positive ( σ 1 > 0 \sigma_1 > 0 σ 1 ​ > 0 and σ 2 > 0 \sigma_2 > 0 σ 2 ​ > 0 ) : σ I = σ 1 , σ I I = σ 2 , σ I I I = 0 \sigma_I = \sigma_1, \quad \sigma_{II} = \sigma_2, \quad \sigma_{III} = 0 σ I ​ = σ 1 ​ , σ II ​ = σ 2 ​ , σ III ​ = 0 τ max ⁡ , a b s = σ 1 − 0 2 = σ 1 2 \tau_{\max, abs} = \frac{\sigma_1 - 0}{2} = \frac{\sigma_1}{2} τ m a x , ab s ​ = 2 σ 1 ​ − 0 ​ = 2 σ 1 ​ ​

Both Negative ( σ 1 < 0 \sigma_1 < 0 σ 1 ​ < 0 and σ 2 < 0 \sigma_2 < 0 σ 2 ​ < 0 ) : σ I = 0 , σ I I = σ 1 , σ I I I = σ 2 \sigma_I = 0, \quad \sigma_{II} = \sigma_1, \quad \sigma_{III} = \sigma_2 σ I ​ = 0 , σ II ​ = σ 1 ​ , σ III ​ = σ 2 ​ τ max ⁡ , a b s = 0 − σ 2 2 = ∣ σ 2 ∣ 2 \tau_{\max, abs} = \frac{0 - \sigma_2}{2} = \frac{|\sigma_2|}{2} τ m a x , ab s ​ = 2 0 − σ 2 ​ ​ = 2 ∣ σ 2 ​ ∣ ​

Warning

Neglecting the out-of-plane principal stress σ 3 = 0 \sigma_3 = 0 σ 3 ​ = 0 when σ 1 \sigma_1 σ 1 ​ and σ 2 \sigma_2 σ 2 ​ have identical signs can grossly underestimate the maximum shear stress (in equal biaxial tension the in-plane value is zero, while the true value is σ 1 / 2 \sigma_1/2 σ 1 ​ /2 ), yielding non-conservative failure predictions under the Maximum Shear Stress (Tresca) criterion.

Mohr's Circle Construction and Properties

Mohr's circle is a geometric representation of stress transformation. Squaring and adding the transformation equations for σ x ′ \sigma_{x'} σ x ′ ​ and τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ ​ eliminates the transformation angle θ \theta θ : ( σ x ′ − σ avg ) 2 + τ x ′ y ′ 2 = R 2 \left(\sigma_{x'} - \sigma_{\text{avg}}\right)^2 + \tau_{x'y'}^2 = R^2 ( σ x ′ ​ − σ avg ​ ) 2 + τ x ′ y ′ 2 ​ = R 2

This represents a circle in the ( σ , τ ) (\sigma, \tau) ( σ , τ ) plane with:

Center Coordinates : C = ( σ avg , 0 ) = ( σ x + σ y 2 , 0 ) C = (\sigma_{\text{avg}}, 0) = \left(\frac{\sigma_x + \sigma_y}{2}, 0\right) C = ( σ avg ​ , 0 ) = ( 2 σ x ​ + σ y ​ ​ , 0 )

Circle Radius : R = ( σ x − σ y 2 ) 2 + τ x y 2 R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} R = ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​

Construction Rules:

Normal tensile stresses are plotted along the positive horizontal axis ( + σ +\sigma + σ ); compressive stresses along the negative axis ( − σ -\sigma − σ ).

Use the clockwise-up convention: a face shear stress that tends to rotate the element clockwise is plotted above the σ \sigma σ -axis, and one that tends to rotate it counterclockwise is plotted below.

Plot point X X X for the vertical x x x -face at abscissa σ x \sigma_x σ x ​ . A positive τ x y \tau_{xy} τ x y ​ on the x x x -face turns the element counterclockwise, so X X X plots below the axis at a distance τ x y \tau_{xy} τ x y ​ .

Plot point Y Y Y for the horizontal y y y -face at abscissa σ y \sigma_y σ y ​ . Its shear has the opposite sense, so for positive τ x y \tau_{xy} τ x y ​ the point Y Y Y plots above the axis.

Connect points X X X and Y Y Y with a straight line. The intersection with the σ \sigma σ -axis defines the circle center C C C .

An angle of rotation θ \theta θ on the physical stress element corresponds to an angle of 2 θ 2\theta 2 θ in the same rotational direction on Mohr's circle. (Some texts instead plot X X X at ( σ x , + τ x y ) (\sigma_x, +\tau_{xy}) ( σ x ​ , + τ x y ​ ) with shear positive upward; the circle is then mirrored and rotations run in the opposite sense. Either convention works if it is used consistently.)

In three dimensions, the general stress state produces three mutually tangent Mohr's circles plotted between pairs ( σ 1 , σ 2 ) (\sigma_1, \sigma_2) ( σ 1 ​ , σ 2 ​ ) , ( σ 2 , σ 3 ) (\sigma_2, \sigma_3) ( σ 2 ​ , σ 3 ​ ) , and ( σ 1 , σ 3 ) (\sigma_1, \sigma_3) ( σ 1 ​ , σ 3 ​ ) . Any allowable oblique plane stress state falls within the shaded annular region bounded by the three circles.

  • Strain Transformations, Rosettes & Generalized Hooke's Law
  • Strain Transformations

Because strain forms a second-order symmetric tensor analogous to stress, plane strain transformations follow identical trigonometric relationships, substituting tensorial shear strain ϵ x y = γ x y / 2 \epsilon_{xy} = \gamma_{xy} / 2 ϵ x y ​ = γ x y ​ /2 for τ x y \tau_{xy} τ x y ​ : ϵ θ = ϵ x + ϵ y 2 + ϵ x − ϵ y 2 cos ⁡ 2 θ + γ x y 2 sin ⁡ 2 θ \epsilon_\theta = \frac{\epsilon_x + \epsilon_y}{2} + \frac{\epsilon_x - \epsilon_y}{2} \cos 2\theta + \frac{\gamma_{xy}}{2} \sin 2\theta ϵ θ ​ = 2 ϵ x ​ + ϵ y ​ ​ + 2 ϵ x ​ − ϵ y ​ ​ cos 2 θ + 2 γ x y ​ ​ sin 2 θ

Strain Rosette Analysis

Strain gages measure normal surface strains along specific orientations. Multi-axis strain rosettes determine the complete in-plane strain tensor ( ϵ x , ϵ y , γ x y ) (\epsilon_x, \epsilon_y, \gamma_{xy}) ( ϵ x ​ , ϵ y ​ , γ x y ​ ) :

Rectangular ( 45 ∘ 45^\circ 4 5 ∘ ) Rosette : Three gages positioned at θ a = 0 ∘ \theta_a = 0^\circ θ a ​ = 0 ∘ , θ b = 45 ∘ \theta_b = 45^\circ θ b ​ = 4 5 ∘ , and θ c = 90 ∘ \theta_c = 90^\circ θ c ​ = 9 0 ∘ : ϵ x = ϵ a , ϵ y = ϵ c , γ x y = 2 ϵ b − ( ϵ a + ϵ c ) \epsilon_x = \epsilon_a, \quad \epsilon_y = \epsilon_c, \quad \gamma_{xy} = 2 \epsilon_b - (\epsilon_a + \epsilon_c) ϵ x ​ = ϵ a ​ , ϵ y ​ = ϵ c ​ , γ x y ​ = 2 ϵ b ​ − ( ϵ a ​ + ϵ c ​ )

Delta ( 60 ∘ 60^\circ 6 0 ∘ ) Rosette : Three gages positioned at θ a = 0 ∘ \theta_a = 0^\circ θ a ​ = 0 ∘ , θ b = 60 ∘ \theta_b = 60^\circ θ b ​ = 6 0 ∘ , and θ c = 120 ∘ \theta_c = 120^\circ θ c ​ = 12 0 ∘ : ϵ x = ϵ a , ϵ y = 2 ( ϵ b + ϵ c ) − ϵ a 3 , γ x y = 2 ( ϵ b − ϵ c ) 3 \epsilon_x = \epsilon_a, \quad \epsilon_y = \frac{2(\epsilon_b + \epsilon_c) - \epsilon_a}{3}, \quad \gamma_{xy} = \frac{2(\epsilon_b - \epsilon_c)}{\sqrt{3}} ϵ x ​ = ϵ a ​ , ϵ y ​ = 3 2 ( ϵ b ​ + ϵ c ​ ) − ϵ a ​ ​ , γ x y ​ = 3 ​ 2 ( ϵ b ​ − ϵ c ​ ) ​

Generalized Hooke's Law in 3D

For an isotropic linear elastic material, the three-dimensional stress-strain relations are: ϵ x = 1 E [ σ x − ν ( σ y + σ z ) ] \epsilon_x = \frac{1}{E}\left[\sigma_x - \nu(\sigma_y + \sigma_z)\right] ϵ x ​ = E 1 ​ [ σ x ​ − ν ( σ y ​ + σ z ​ ) ] ϵ y = 1 E [ σ y − ν ( σ x + σ z ) ] \epsilon_y = \frac{1}{E}\left[\sigma_y - \nu(\sigma_x + \sigma_z)\right] ϵ y ​ = E 1 ​ [ σ y ​ − ν ( σ x ​ + σ z ​ ) ] ϵ z = 1 E [ σ z − ν ( σ x + σ y ) ] \epsilon_z = \frac{1}{E}\left[\sigma_z - \nu(\sigma_x + \sigma_y)\right] ϵ z ​ = E 1 ​ [ σ z ​ − ν ( σ x ​ + σ y ​ ) ] γ x y = τ x y G = 2 ( 1 + ν ) E τ x y \gamma_{xy} = \frac{\tau_{xy}}{G} = \frac{2(1+\nu)}{E} \tau_{xy} γ x y ​ = G τ x y ​ ​ = E 2 ( 1 + ν ) ​ τ x y ​

For plane stress ( σ z = 0 \sigma_z = 0 σ z ​ = 0 ), inverting Hooke's law yields: σ x = E 1 − ν 2 ( ϵ x + ν ϵ y ) , σ y = E 1 − ν 2 ( ϵ y + ν ϵ x ) \sigma_x = \frac{E}{1 - \nu^2}(\epsilon_x + \nu \epsilon_y), \quad \sigma_y = \frac{E}{1 - \nu^2}(\epsilon_y + \nu \epsilon_x) σ x ​ = 1 − ν 2 E ​ ( ϵ x ​ + ν ϵ y ​ ) , σ y ​ = 1 − ν 2 E ​ ( ϵ y ​ + ν ϵ x ​ )

Note that out-of-plane normal strain is non-zero due to Poisson's effect: ϵ z = − ν E ( σ x + σ y ) = − ν 1 − ν ( ϵ x + ϵ y ) \epsilon_z = -\frac{\nu}{E}(\sigma_x + \sigma_y) = -\frac{\nu}{1-\nu}(\epsilon_x + \epsilon_y) ϵ z ​ = − E ν ​ ( σ x ​ + σ y ​ ) = − 1 − ν ν ​ ( ϵ x ​ + ϵ y ​ ) .

  • Complete Worked Numerical Example: Transmission Shaft Under Combined Loading
  • Problem Statement

A solid steel drive shaft of diameter d = 50.0 mm d = 50.0\,\text{mm} d = 50.0 mm operates under simultaneous axial tension, bending, and torsion. At the critical outer surface fiber, the applied loads are:

Axial tensile force: P = 40.0 kN = 40,000 N P = 40.0\,\text{kN} = 40{,}000\,\text{N} P = 40.0 kN = 40 , 000 N

Bending moment: M = 1.20 kN ⋅ m = 1200 N ⋅ m M = 1.20\,\text{kN}\cdot\text{m} = 1200\,\text{N}\cdot\text{m} M = 1.20 kN ⋅ m = 1200 N ⋅ m

Torsional torque: T = 1.80 kN ⋅ m = 1800 N ⋅ m T = 1.80\,\text{kN}\cdot\text{m} = 1800\,\text{N}\cdot\text{m} T = 1.80 kN ⋅ m = 1800 N ⋅ m

Determine:

The combined state of stress ( σ x , σ y , τ x y ) (\sigma_x, \sigma_y, \tau_{xy}) ( σ x ​ , σ y ​ , τ x y ​ ) at the top outermost fiber.

The principal normal stresses σ 1 , σ 2 \sigma_1, \sigma_2 σ 1 ​ , σ 2 ​ and principal orientation θ p \theta_p θ p ​ .

The maximum in-plane shear stress τ max ⁡ , i n \tau_{\max, in} τ m a x , in ​ and absolute maximum shear stress τ max ⁡ , a b s \tau_{\max, abs} τ m a x , ab s ​ .

Step 1: Compute Geometric Section Properties A = π d 2 4 = π ( 0.050 m ) 2 4 = 1.9635 × 10 − 3 m 2 A = \frac{\pi d^2}{4} = \frac{\pi (0.050\,\text{m})^2}{4} = 1.9635 \times 10^{-3}\,\text{m}^2 A = 4 π d 2 ​ = 4 π ( 0.050 m ) 2 ​ = 1.9635 × 1 0 − 3 m 2 Z = π d 3 32 = π ( 0.050 m ) 3 32 = 1.2272 × 10 − 5 m 3 Z = \frac{\pi d^3}{32} = \frac{\pi (0.050\,\text{m})^3}{32} = 1.2272 \times 10^{-5}\,\text{m}^3 Z = 32 π d 3 ​ = 32 π ( 0.050 m ) 3 ​ = 1.2272 × 1 0 − 5 m 3 Z p = π d 3 16 = π ( 0.050 m ) 3 16 = 2.4544 × 10 − 5 m 3 Z_p = \frac{\pi d^3}{16} = \frac{\pi (0.050\,\text{m})^3}{16} = 2.4544 \times 10^{-5}\,\text{m}^3 Z p ​ = 16 π d 3 ​ = 16 π ( 0.050 m ) 3 ​ = 2.4544 × 1 0 − 5 m 3

Step 2: Calculate In-Plane Stress Components

The axial force and bending moment produce normal stresses aligned along the x x x -axis: σ axial = P A = 40,000 N 1.9635 × 10 − 3 m 2 = 20.37 × 10 6 Pa = 20.37 MPa \sigma_{\text{axial}} = \frac{P}{A} = \frac{40{,}000\,\text{N}}{1.9635 \times 10^{-3}\,\text{m}^2} = 20.37 \times 10^6\,\text{Pa} = 20.37\,\text{MPa} σ axial ​ = A P ​ = 1.9635 × 1 0 − 3 m 2 40 , 000 N ​ = 20.37 × 1 0 6 Pa = 20.37 MPa σ bending = M Z = 1200 N ⋅ m 1.2272 × 10 − 5 m 3 = 97.78 × 10 6 Pa = 97.78 MPa \sigma_{\text{bending}} = \frac{M}{Z} = \frac{1200\,\text{N}\cdot\text{m}}{1.2272 \times 10^{-5}\,\text{m}^3} = 97.78 \times 10^6\,\text{Pa} = 97.78\,\text{MPa} σ bending ​ = Z M ​ = 1.2272 × 1 0 − 5 m 3 1200 N ⋅ m ​ = 97.78 × 1 0 6 Pa = 97.78 MPa σ x = σ axial + σ bending = 20.37 + 97.78 = 118.15 MPa \sigma_x = \sigma_{\text{axial}} + \sigma_{\text{bending}} = 20.37 + 97.78 = 118.15\,\text{MPa} σ x ​ = σ axial ​ + σ bending ​ = 20.37 + 97.78 = 118.15 MPa σ y = 0 MPa \sigma_y = 0\,\text{MPa} σ y ​ = 0 MPa

The torsional shear stress is: τ x y = T Z p = 1800 N ⋅ m 2.4544 × 10 − 5 m 3 = 73.34 × 10 6 Pa = 73.34 MPa \tau_{xy} = \frac{T}{Z_p} = \frac{1800\,\text{N}\cdot\text{m}}{2.4544 \times 10^{-5}\,\text{m}^3} = 73.34 \times 10^6\,\text{Pa} = 73.34\,\text{MPa} τ x y ​ = Z p ​ T ​ = 2.4544 × 1 0 − 5 m 3 1800 N ⋅ m ​ = 73.34 × 1 0 6 Pa = 73.34 MPa

Step 3: Determine Mohr's Circle Parameters

Center of Mohr's circle: σ avg = σ x + σ y 2 = 118.15 + 0 2 = 59.08 MPa \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} = \frac{118.15 + 0}{2} = 59.08\,\text{MPa} σ avg ​ = 2 σ x ​ + σ y ​ ​ = 2 118.15 + 0 ​ = 59.08 MPa

Radius of Mohr's circle: R = ( σ x − σ y 2 ) 2 + τ x y 2 = ( 59.08 ) 2 + ( 73.34 ) 2 = 3490.45 + 5378.76 = 8869.21 = 94.18 MPa R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} = \sqrt{(59.08)^2 + (73.34)^2} = \sqrt{3490.45 + 5378.76} = \sqrt{8869.21} = 94.18\,\text{MPa} R = ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​ = ( 59.08 ) 2 + ( 73.34 ) 2 ​ = 3490.45 + 5378.76 ​ = 8869.21 ​ = 94.18 MPa

Step 4: Calculate Principal Stresses & Principal Plane Orientation σ 1 = σ avg + R = 59.08 + 94.18 = 153.26 MPa \sigma_1 = \sigma_{\text{avg}} + R = 59.08 + 94.18 = 153.26\,\text{MPa} σ 1 ​ = σ avg ​ + R = 59.08 + 94.18 = 153.26 MPa σ 2 = σ avg − R = 59.08 − 94.18 = − 35.10 MPa \sigma_2 = \sigma_{\text{avg}} - R = 59.08 - 94.18 = -35.10\,\text{MPa} σ 2 ​ = σ avg ​ − R = 59.08 − 94.18 = − 35.10 MPa σ 3 = 0 MPa ( free surface plane stress ) \sigma_3 = 0\,\text{MPa} \quad (\text{free surface plane stress}) σ 3 ​ = 0 MPa ( free surface plane stress )

Orientation of principal plane: tan ⁡ 2 θ p = 2 τ x y σ x − σ y = 2 × 73.34 118.15 − 0 = 146.68 118.15 = 1.2415 \tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y} = \frac{2 \times 73.34}{118.15 - 0} = \frac{146.68}{118.15} = 1.2415 tan 2 θ p ​ = σ x ​ − σ y ​ 2 τ x y ​ ​ = 118.15 − 0 2 × 73.34 ​ = 118.15 146.68 ​ = 1.2415 2 θ p = arctan ⁡ ( 1.2415 ) = 51.15 ∘ ⟹ θ p 1 = 25.58 ∘ 2\theta_p = \arctan(1.2415) = 51.15^\circ \implies \theta_{p1} = 25.58^\circ 2 θ p ​ = arctan ( 1.2415 ) = 51.1 5 ∘ ⟹ θ p 1 ​ = 25.5 8 ∘

Step 5: Evaluate Maximum Shear Stresses

Maximum in-plane shear stress: τ max ⁡ , i n = R = 94.18 MPa \tau_{\max, in} = R = 94.18\,\text{MPa} τ m a x , in ​ = R = 94.18 MPa

Absolute maximum shear stress:

Arranging all three principal stresses algebraically: σ I = 153.26 MPa \sigma_I = 153.26\,\text{MPa} σ I ​ = 153.26 MPa , σ I I = 0 MPa \sigma_{II} = 0\,\text{MPa} σ II ​ = 0 MPa , σ I I I = − 35.10 MPa \sigma_{III} = -35.10\,\text{MPa} σ III ​ = − 35.10 MPa . τ max ⁡ , a b s = σ I − σ I I I 2 = 153.26 − ( − 35.10 ) 2 = 188.36 2 = 94.18 MPa \tau_{\max, abs} = \frac{\sigma_I - \sigma_{III}}{2} = \frac{153.26 - (-35.10)}{2} = \frac{188.36}{2} = 94.18\,\text{MPa} τ m a x , ab s ​ = 2 σ I ​ − σ III ​ ​ = 2 153.26 − ( − 35.10 ) ​ = 2 188.36 ​ = 94.18 MPa

Because the in-plane principal stresses have opposite algebraic signs ( σ 1 > 0 \sigma_1 > 0 σ 1 ​ > 0 and σ 2 < 0 \sigma_2 < 0 σ 2 ​ < 0 ), the absolute maximum shear stress coincides with the in-plane maximum shear stress.