Study guide

4.3 Thermal Stresses & Interference Stresses

PE Mechanical: Machine Design and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology

1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety

2 Chapter 2: Physical & Mechanical Properties of Engineering Materials

2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep

3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections

3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis

4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects

4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses

5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics

5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics

6 Chapter 6: Fatigue Analysis & Dynamic Failure

6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage

7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints

7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors

8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding

8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding

9 Chapter 9: Power Transmission: Shafts & Gearing

9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing

10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers

10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels

11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems

11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods

12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power

12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics

13 Chapter 13: Kinematics, Mechatronics & Control Systems

13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls

14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods

14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly

15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion

15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement

4.3 Thermal Stresses & Interference Stresses

Key Takeaways Explain This Topic AI

Unconstrained thermal expansion produces strain ϵ T = α Δ T \epsilon_T = \alpha \Delta T ϵ T ​ = α Δ T without generating mechanical stress; thermal stress develops exclusively when external boundary constraints, displacement gaps, or material mismatches prevent free thermal deformation.

In a statically indeterminate bar with rigid axial end constraints, uniform temperature change produces axial stress σ = − E α Δ T \sigma = -E \alpha \Delta T σ = − E α Δ T ; any initial clearance gap δ gap \delta_{\text{gap}} δ gap ​ reduces the induced stress to σ = − E ( α Δ T − δ gap L ) \sigma = -E\left(\alpha \Delta T - \frac{\delta_{\text{gap}}}{L}\right) σ = − E ( α Δ T − L δ gap ​ ​ ) .

Thick-walled cylinders under internal and external pressure follow Lamé's equations, with peak tangential hoop stress always occurring at the innermost bore radius r = r i r = r_i r = r i ​ under internal pressure.

Interference press and shrink fits generate interface contact pressure p p p proportional to diametral interference δ \delta δ , producing maximum tensile hoop stress at the inner bore of the outer hub and uniform in-plane hydrostatic compression within a solid inner shaft.

Thermal shrink-fit assembly requires heating the hub or chilling the shaft to achieve a temperature differential Δ T = δ + δ clearance α d \Delta T = \frac{\delta + \delta_{\text{clearance}}}{\alpha d} Δ T = α d δ + δ clearance ​ ​ , where δ clearance \delta_{\text{clearance}} δ clearance ​ prevents premature binding during assembly.

Last updated: October 2026

4.3 Thermal Stresses & Interference Stresses

Thermal expansion and press/shrink fit interferences represent two primary sources of internal pre-stress in mechanical engineering. When thermal expansion is constrained by adjacent structural boundaries, massive compressive or tensile reaction stresses emerge. Similarly, press and shrink fits intentionally exploit radial dimensional interference to generate high contact pressures, enabling torque transmission across hubs, gears, bearings, and shafts without keyways. Accurately modeling these stresses via Lamé's equations and thermoelastic compatibility is vital to avoid premature yielding, fatigue failure, or joint slippage.

Thermal Expansion and Indeterminate Restraint

When a homogeneous, isotropic body experiences a uniform temperature change Δ T = T final − T initial \Delta T = T_{\text{final}} - T_{\text{initial}} Δ T = T final ​ − T initial ​ , it undergoes an unconstrained thermal strain ϵ T \epsilon_T ϵ T ​ : ϵ T = α Δ T \epsilon_T = \alpha \Delta T ϵ T ​ = α Δ T

where α \alpha α is the linear coefficient of thermal expansion (units of μ m / ( m ⋅ ∘ C ) \mu\text{m}/(\text{m}\cdot^\circ\text{C}) μ m / ( m ⋅ ∘ C ) or 10 − 6 / ∘ F 10^{-6}\;/^\circ\text{F} 1 0 − 6 / ∘ F ). The unrestrained change in length of a member of length L L L is: δ T = α L Δ T \delta_T = \alpha L \Delta T δ T ​ = αL Δ T

Important

Free thermal expansion or contraction creates shape or volumetric change without generating mechanical stress ( σ = 0 \sigma = 0 σ = 0 ). Thermal stress develops exclusively when external boundary constraints, displacement gaps, or material property mismatches prevent unconstrained expansion.

Statically Indeterminate Fixed Bar

If a uniform bar of cross-sectional area A A A and modulus E E E is rigidly confined between immovable walls, the total axial deformation must equal zero: δ total = δ T + δ P = 0 \delta_{\text{total}} = \delta_T + \delta_P = 0 δ total ​ = δ T ​ + δ P ​ = 0

Substituting δ T = α L Δ T \delta_T = \alpha L \Delta T δ T ​ = αL Δ T and mechanical strain displacement δ P = P L A E \delta_P = \frac{P L}{A E} δ P ​ = A E P L ​ : α L Δ T + P L A E = 0 ⟹ σ = P A = − E α Δ T \alpha L \Delta T + \frac{P L}{A E} = 0 \implies \sigma = \frac{P}{A} = -E \alpha \Delta T αL Δ T + A E P L ​ = 0 ⟹ σ = A P ​ = − E α Δ T

A temperature increase ( Δ T > 0 \Delta T > 0 Δ T > 0 ) generates compressive stress, whereas a temperature drop ( Δ T < 0 \Delta T < 0 Δ T < 0 ) causes tensile stress.

Restrained Bar with Initial Clearance Gap

When an initial clearance gap δ gap \delta_{\text{gap}} δ gap ​ exists between the bar and a rigid support:

If δ T ≤ δ gap \delta_T \le \delta_{\text{gap}} δ T ​ ≤ δ gap ​ , the bar expands freely without contact: σ = 0 \sigma = 0 σ = 0 .

If δ T > δ gap \delta_T > \delta_{\text{gap}} δ T ​ > δ gap ​ , the bar closes the gap, inducing a compressive reaction force: δ T − P L A E = δ gap ⟹ σ = − E ( α Δ T − δ gap L ) \delta_T - \frac{P L}{A E} = \delta_{\text{gap}} \implies \sigma = -E \left(\alpha \Delta T - \frac{\delta_{\text{gap}}}{L}\right) δ T ​ − A E P L ​ = δ gap ​ ⟹ σ = − E ( α Δ T − L δ gap ​ ​ )

Bi-Metallic Strips and Thermal Curvature

A bi-metallic strip consists of two dissimilar thin metal strips of equal thickness t 1 = t 2 = t / 2 t_1 = t_2 = t/2 t 1 ​ = t 2 ​ = t /2 and equal width b b b bonded together along their faces. If material 2 has a higher thermal expansion coefficient than material 1 ( α 2 > α 1 \alpha_2 > \alpha_1 α 2 ​ > α 1 ​ ), heating induces differential expansion, forcing the composite beam to bend into an arc of curvature κ = 1 / ρ \kappa = 1/\rho κ = 1/ ρ .

Assuming equal elastic moduli ( E 1 = E 2 = E E_1 = E_2 = E E 1 ​ = E 2 ​ = E ), Timoshenko's classical bi-metallic formulation yields the beam curvature: κ = 1 ρ = 3 ( α 2 − α 1 ) Δ T 2 t \kappa = \frac{1}{\rho} = \frac{3 (\alpha_2 - \alpha_1) \Delta T}{2 t} κ = ρ 1 ​ = 2 t 3 ( α 2 ​ − α 1 ​ ) Δ T ​

where t t t is the total combined thickness ( t = t 1 + t 2 t = t_1 + t_2 t = t 1 ​ + t 2 ​ ). For a cantilever strip of length L L L , the tip deflection v tip v_{\text{tip}} v tip ​ is: v tip ≈ L 2 2 ρ = 3 ( α 2 − α 1 ) Δ T L 2 4 t v_{\text{tip}} \approx \frac{L^2}{2 \rho} = \frac{3 (\alpha_2 - \alpha_1) \Delta T L^2}{4 t} v tip ​ ≈ 2 ρ L 2 ​ = 4 t 3 ( α 2 ​ − α 1 ​ ) Δ T L 2 ​

Thick-Walled Cylinders: Lamé's Equations

When a cylindrical pressure vessel, pipe, or machine bushing has a wall thickness exceeding approximately one-tenth of its inner radius ( t > 0.1 r i t > 0.1 r_i t > 0.1 r i ​ ), the thin-walled membrane assumption breaks down. The hoop (tangential) stress varies significantly across the radial thickness.

Consider a cylinder of inner radius r i r_i r i ​ and outer radius r o r_o r o ​ subjected to internal pressure p i p_i p i ​ and external pressure p o p_o p o ​ . The general radial equilibrium equation for an axisymmetric differential element is: d σ r d r + σ r − σ t r = 0 \frac{d\sigma_r}{dr} + \frac{\sigma_r - \sigma_t}{r} = 0 d r d σ r ​ ​ + r σ r ​ − σ t ​ ​ = 0

Assuming plane strain ( ϵ z = constant \epsilon_z = \text{constant} ϵ z ​ = constant ) or plane stress ( σ z = constant \sigma_z = \text{constant} σ z ​ = constant ), solving the differential equation yields the Lamé equations : σ t ( r ) = p i r i 2 − p o r o 2 r o 2 − r i 2 + r i 2 r o 2 ( p i − p o ) r 2 ( r o 2 − r i 2 ) \sigma_t(r) = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} + \frac{r_i^2 r_o^2 (p_i - p_o)}{r^2 (r_o^2 - r_i^2)} σ t ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​ + r 2 ( r o 2 ​ − r i 2 ​ ) r i 2 ​ r o 2 ​ ( p i ​ − p o ​ ) ​ σ r ( r ) = p i r i 2 − p o r o 2 r o 2 − r i 2 − r i 2 r o 2 ( p i − p o ) r 2 ( r o 2 − r i 2 ) \sigma_r(r) = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} - \frac{r_i^2 r_o^2 (p_i - p_o)}{r^2 (r_o^2 - r_i^2)} σ r ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​ − r 2 ( r o 2 ​ − r i 2 ​ ) r i 2 ​ r o 2 ​ ( p i ​ − p o ​ ) ​

where:

σ t ( r ) \sigma_t(r) σ t ​ ( r ) is the tangential (hoop) normal stress at radius r r r ,

σ r ( r ) \sigma_r(r) σ r ​ ( r ) is the radial normal stress at radius r r r .

For closed-end cylinders, axial equilibrium yields uniform longitudinal stress: σ z = p i r i 2 − p o r o 2 r o 2 − r i 2 \sigma_z = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2} σ z ​ = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ − p o ​ r o 2 ​ ​

Case 1: Internal Pressure Only ( p o = 0 p_o = 0 p o ​ = 0 )

When external pressure is zero, Lamé's equations simplify to: σ t ( r ) = p i r i 2 r o 2 − r i 2 ( 1 + r o 2 r 2 ) \sigma_t(r) = \frac{p_i r_i^2}{r_o^2 - r_i^2}\left(1 + \frac{r_o^2}{r^2}\right) σ t ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ ​ ( 1 + r 2 r o 2 ​ ​ ) σ r ( r ) = p i r i 2 r o 2 − r i 2 ( 1 − r o 2 r 2 ) \sigma_r(r) = \frac{p_i r_i^2}{r_o^2 - r_i^2}\left(1 - \frac{r_o^2}{r^2}\right) σ r ​ ( r ) = r o 2 ​ − r i 2 ​ p i ​ r i 2 ​ ​ ( 1 − r 2 r o 2 ​ ​ )

At the inner surface ( r = r i r = r_i r = r i ​ ) : σ t ( r i ) = p i ( r o 2 + r i 2 r o 2 − r i 2 ) ( maximum tensile hoop stress ) \sigma_t(r_i) = p_i \left(\frac{r_o^2 + r_i^2}{r_o^2 - r_i^2}\right) \quad (\text{maximum tensile hoop stress}) σ t ​ ( r i ​ ) = p i ​ ( r o 2 ​ − r i 2 ​ r o 2 ​ + r i 2 ​ ​ ) ( maximum tensile hoop stress ) σ r ( r i ) = − p i ( compressive ) \sigma_r(r_i) = -p_i \quad (\text{compressive}) σ r ​ ( r i ​ ) = − p i ​ ( compressive )

At the outer surface ( r = r o r = r_o r = r o ​ ) : σ t ( r o ) = 2 p i r i 2 r o 2 − r i 2 \sigma_t(r_o) = \frac{2 p_i r_i^2}{r_o^2 - r_i^2} σ t ​ ( r o ​ ) = r o 2 ​ − r i 2 ​ 2 p i ​ r i 2 ​ ​ σ r ( r o ) = 0 \sigma_r(r_o) = 0 σ r ​ ( r o ​ ) = 0

Case 2: External Pressure Only ( p i = 0 p_i = 0 p i ​ = 0 )

When internal pressure is zero (e.g., submarine hull or shrink-fit shaft): σ t ( r ) = − p o r o 2 r o 2 − r i 2 ( 1 + r i 2 r 2 ) \sigma_t(r) = -\frac{p_o r_o^2}{r_o^2 - r_i^2}\left(1 + \frac{r_i^2}{r^2}\right) σ t ​ ( r ) = − r o 2 ​ − r i 2 ​ p o ​ r o 2 ​ ​ ( 1 + r 2 r i 2 ​ ​ ) σ r ( r ) = − p o r o 2 r o 2 − r i 2 ( 1 − r i 2 r 2 ) \sigma_r(r) = -\frac{p_o r_o^2}{r_o^2 - r_i^2}\left(1 - \frac{r_i^2}{r^2}\right) σ r ​ ( r ) = − r o 2 ​ − r i 2 ​ p o ​ r o 2 ​ ​ ( 1 − r 2 r i 2 ​ ​ )

Maximum compressive hoop stress occurs at the innermost bore ( r = r i r = r_i r = r i ​ ): σ t ( r i ) = − 2 p o r o 2 r o 2 − r i 2 \sigma_t(r_i) = -\frac{2 p_o r_o^2}{r_o^2 - r_i^2} σ t ​ ( r i ​ ) = − r o 2 ​ − r i 2 ​ 2 p o ​ r o 2 ​ ​

Shrink and Press Fits: Interface Mechanics

In an interference fit, the outer component (hub, sleeve, or gear) is fabricated with an inner diameter d hub d_{\text{hub}} d hub ​ smaller than the outer diameter d shaft d_{\text{shaft}} d shaft ​ of the inner component (shaft or bushing). The total diametral interference is: δ = d shaft − d hub \delta = d_{\text{shaft}} - d_{\text{hub}} δ = d shaft ​ − d hub ​

Correspondingly, radial interference is δ r = δ / 2 \delta_r = \delta / 2 δ r ​ = δ /2 .

Interface Contact Pressure ( p p p )

When assembled, the interface must satisfy displacement compatibility: the radial expansion of the hub bore plus the radial compression of the shaft outer surface equals the initial radial interference: δ r = u r , hub ( d / 2 ) + ∣ u r , shaft ( d / 2 ) ∣ \delta_r = u_{r,\text{hub}}(d/2) + |u_{r,\text{shaft}}(d/2)| δ r ​ = u r , hub ​ ( d /2 ) + ∣ u r , shaft ​ ( d /2 ) ∣

Applying Hooke's law in polar coordinates with Lamé stress distributions yields the master contact pressure equation: p = δ d [ 1 E o ( d o 2 + d 2 d o 2 − d 2 + ν o ) + 1 E i ( d 2 + d i 2 d 2 − d i 2 − ν i ) ] p = \frac{\delta}{d \left[ \frac{1}{E_o}\left(\frac{d_o^2 + d^2}{d_o^2 - d^2} + \nu_o\right) + \frac{1}{E_i}\left(\frac{d^2 + d_i^2}{d^2 - d_i^2} - \nu_i\right) \right]} p = d [ E o ​ 1 ​ ( d o 2 ​ − d 2 d o 2 ​ + d 2 ​ + ν o ​ ) + E i ​ 1 ​ ( d 2 − d i 2 ​ d 2 + d i 2 ​ ​ − ν i ​ ) ] δ ​

where:

  • d d d is the nominal mating interface diameter,
  • d o d_o d o ​ is the outer diameter of the hub,
  • d i d_i d i ​ is the inner diameter of the shaft ( d i = 0 d_i = 0 d i ​ = 0 for a solid shaft),

E o , ν o E_o, \nu_o E o ​ , ν o ​ and E i , ν i E_i, \nu_i E i ​ , ν i ​ are Young's modulus and Poisson's ratio for the outer hub and inner shaft.

Specialized Case: Solid Shaft of Same Material ( E o = E i = E , ν o = ν i = ν , d i = 0 E_o = E_i = E, \nu_o = \nu_i = \nu, d_i = 0 E o ​ = E i ​ = E , ν o ​ = ν i ​ = ν , d i ​ = 0 )

For a solid shaft mated with a hub of identical material, the contact pressure equation reduces to: p = E δ 2 d ( 1 − d 2 d o 2 ) p = \frac{E \delta}{2 d} \left(1 - \frac{d^2}{d_o^2}\right) p = 2 d E δ ​ ( 1 − d o 2 ​ d 2 ​ )

Maximum Stresses in Assembly

Outer Hub (Worst-Case Location) :

The peak stress occurs at the inner bore ( r = d / 2 r = d/2 r = d /2 ): σ t , o = p ( d o 2 + d 2 d o 2 − d 2 ) ( tension ) \sigma_{t,o} = p \left(\frac{d_o^2 + d^2}{d_o^2 - d^2}\right) \quad (\text{tension}) σ t , o ​ = p ( d o 2 ​ − d 2 d o 2 ​ + d 2 ​ ) ( tension ) σ r , o = − p ( compression ) \sigma_{r,o} = -p \quad (\text{compression}) σ r , o ​ = − p ( compression )

Under the von Mises yield criterion for plane stress ( σ z = 0 \sigma_z = 0 σ z ​ = 0 ): σ v M , o = σ t , o 2 − σ t , o σ r , o + σ r , o 2 = σ t , o 2 + σ t , o p + p 2 \sigma_{vM,o} = \sqrt{\sigma_{t,o}^2 - \sigma_{t,o}\sigma_{r,o} + \sigma_{r,o}^2} = \sqrt{\sigma_{t,o}^2 + \sigma_{t,o} p + p^2} σ v M , o ​ = σ t , o 2 ​ − σ t , o ​ σ r , o ​ + σ r , o 2 ​ ​ = σ t , o 2 ​ + σ t , o ​ p + p 2 ​

Inner Solid Shaft :

Every point in a solid inner shaft experiences uniform hydrostatic in-plane compression: σ t , i = σ r , i = − p \sigma_{t,i} = \sigma_{r,i} = -p σ t , i ​ = σ r , i ​ = − p

Because σ 1 = σ 2 = − p \sigma_1 = \sigma_2 = -p σ 1 ​ = σ 2 ​ = − p , the in-plane principal stress difference is zero: σ v M , i = ( − p ) 2 − ( − p ) ( − p ) + ( − p ) 2 = p \sigma_{vM,i} = \sqrt{(-p)^2 - (-p)(-p) + (-p)^2} = p σ v M , i ​ = ( − p ) 2 − ( − p ) ( − p ) + ( − p ) 2 ​ = p

Consequently, the outer hub almost always yields before the solid inner shaft.

Torque and Axial Load Capacity

The interface contact pressure p p p creates a normal clamping force over the contact area A contact = π d L A_{\text{contact}} = \pi d L A contact ​ = π d L , where L L L is the axial engagement length.

Torque Capacity ( T T T ) : T = F friction ⋅ ( d 2 ) = ( μ p π d L ) ( d 2 ) = 1 2 π μ p d 2 L T = F_{\text{friction}} \cdot \left(\frac{d}{2}\right) = (\mu p \pi d L) \left(\frac{d}{2}\right) = \frac{1}{2} \pi \mu p d^2 L T = F friction ​ ⋅ ( 2 d ​ ) = ( μ p π d L ) ( 2 d ​ ) = 2 1 ​ π μ p d 2 L

Axial Force Capacity ( F a x F_{ax} F a x ​ ) : F a x = μ p π d L F_{ax} = \mu p \pi d L F a x ​ = μ p π d L

where μ \mu μ is the static coefficient of friction at the mating interface.

Thermal Assembly Requirements

To assemble an interference fit without mechanical galling or heavy hydraulic pressing, either the hub is heated to expand its bore, or the shaft is cryogenically cooled.

The required diametral thermal expansion must overcome the interference δ \delta δ plus an assembly clearance δ clearance \delta_{\text{clearance}} δ clearance ​ (typically 0.001 d 0.001 d 0.001 d to allow rapid, unjammed slip-on): Δ d total = δ + δ clearance = α d Δ T \Delta d_{\text{total}} = \delta + \delta_{\text{clearance}} = \alpha d \Delta T Δ d total ​ = δ + δ clearance ​ = α d Δ T

Solving for the minimum temperature differential Δ T \Delta T Δ T : Δ T = δ + δ clearance α d \Delta T = \frac{\delta + \delta_{\text{clearance}}}{\alpha d} Δ T = α d δ + δ clearance ​ ​

  • Complete Worked Shrink Fit Design Problem
  • Problem Statement

A solid steel drive shaft ( E i = 207 GPa E_i = 207\,\text{GPa} E i ​ = 207 GPa , ν i = 0.30 \nu_i = 0.30 ν i ​ = 0.30 , α = 11.7 × 10 − 6 / ∘ C \alpha = 11.7 \times 10^{-6}\;/^\circ\text{C} α = 11.7 × 1 0 − 6 / ∘ C ) with nominal diameter d = 80.0 mm d = 80.0\,\text{mm} d = 80.0 mm is shrink-fitted into an alloy steel gear hub ( E o = 207 GPa E_o = 207\,\text{GPa} E o ​ = 207 GPa , ν o = 0.30 \nu_o = 0.30 ν o ​ = 0.30 , yield strength S y = 420 MPa S_y = 420\,\text{MPa} S y ​ = 420 MPa ) having outer diameter d o = 160.0 mm d_o = 160.0\,\text{mm} d o ​ = 160.0 mm and engagement length L = 100.0 mm L = 100.0\,\text{mm} L = 100.0 mm . The measured diametral interference is δ = 0.060 mm = 6.0 × 10 − 5 m \delta = 0.060\,\text{mm} = 6.0 \times 10^{-5}\,\text{m} δ = 0.060 mm = 6.0 × 1 0 − 5 m . The interface coefficient of static friction is μ = 0.15 \mu = 0.15 μ = 0.15 .

Calculate:

The contact pressure p p p at the interface.

The peak tangential hoop stress and von Mises stress in the gear hub.

The maximum torque capacity T T T transmitted before slipping.

The required heating temperature of the hub if ambient temperature is 20 ∘ C 20^\circ\text{C} 2 0 ∘ C and an assembly clearance δ clearance = 0.040 mm \delta_{\text{clearance}} = 0.040\,\text{mm} δ clearance ​ = 0.040 mm is required.

Step 1: Interface Contact Pressure Calculation

Because both members are steel ( E o = E i = 207 GPa E_o = E_i = 207\,\text{GPa} E o ​ = E i ​ = 207 GPa ) and the shaft is solid ( d i = 0 d_i = 0 d i ​ = 0 ): p = E δ 2 d ( 1 − d 2 d o 2 ) p = \frac{E \delta}{2 d} \left(1 - \frac{d^2}{d_o^2}\right) p = 2 d E δ ​ ( 1 − d o 2 ​ d 2 ​ )

Substitute the values: E δ 2 d = ( 207 × 10 9 Pa ) ( 6.0 × 10 − 5 m ) 2 ( 0.080 m ) = 1.242 × 10 7 0.160 = 77.625 × 10 6 Pa = 77.625 MPa \frac{E \delta}{2 d} = \frac{(207 \times 10^9\,\text{Pa})(6.0 \times 10^{-5}\,\text{m})}{2 (0.080\,\text{m})} = \frac{1.242 \times 10^7}{0.160} = 77.625 \times 10^6\,\text{Pa} = 77.625\,\text{MPa} 2 d E δ ​ = 2 ( 0.080 m ) ( 207 × 1 0 9 Pa ) ( 6.0 × 1 0 − 5 m ) ​ = 0.160 1.242 × 1 0 7 ​ = 77.625 × 1 0 6 Pa = 77.625 MPa 1 − d 2 d o 2 = 1 − 80 2 160 2 = 1 − 6400 25600 = 1 − 0.25 = 0.75 1 - \frac{d^2}{d_o^2} = 1 - \frac{80^2}{160^2} = 1 - \frac{6400}{25600} = 1 - 0.25 = 0.75 1 − d o 2 ​ d 2 ​ = 1 − 16 0 2 8 0 2 ​ = 1 − 25600 6400 ​ = 1 − 0.25 = 0.75 p = 77.625 MPa × 0.75 = 58.22 MPa p = 77.625\,\text{MPa} \times 0.75 = 58.22\,\text{MPa} p = 77.625 MPa × 0.75 = 58.22 MPa

Step 2: Peak Stresses in Gear Hub

The peak tangential hoop stress develops at the inner bore of the hub ( r = d / 2 = 40 mm r = d/2 = 40\,\text{mm} r = d /2 = 40 mm ): σ t , o = p ( d o 2 + d 2 d o 2 − d 2 ) = 58.22 MPa × ( 160 2 + 80 2 160 2 − 80 2 ) = 58.22 × 32,000 19,200 = 58.22 × 1.6667 = 97.03 MPa \sigma_{t,o} = p \left(\frac{d_o^2 + d^2}{d_o^2 - d^2}\right) = 58.22\,\text{MPa} \times \left(\frac{160^2 + 80^2}{160^2 - 80^2}\right) = 58.22 \times \frac{32{,}000}{19{,}200} = 58.22 \times 1.6667 = 97.03\,\text{MPa} σ t , o ​ = p ( d o 2 ​ − d 2 d o 2 ​ + d 2 ​ ) = 58.22 MPa × ( 16 0 2 − 8 0 2 16 0 2 + 8 0 2 ​ ) = 58.22 × 19 , 200 32 , 000 ​ = 58.22 × 1.6667 = 97.03 MPa

The radial stress at the interface is: σ r , o = − p = − 58.22 MPa \sigma_{r,o} = -p = -58.22\,\text{MPa} σ r , o ​ = − p = − 58.22 MPa

Compute the von Mises equivalent stress at the inner bore: σ v M = σ t , o 2 − σ t , o σ r , o + σ r , o 2 = ( 97.03 ) 2 − ( 97.03 ) ( − 58.22 ) + ( − 58.22 ) 2 \sigma_{vM} = \sqrt{\sigma_{t,o}^2 - \sigma_{t,o}\sigma_{r,o} + \sigma_{r,o}^2} = \sqrt{(97.03)^2 - (97.03)(-58.22) + (-58.22)^2} σ v M ​ = σ t , o 2 ​ − σ t , o ​ σ r , o ​ + σ r , o 2 ​ ​ = ( 97.03 ) 2 − ( 97.03 ) ( − 58.22 ) + ( − 58.22 ) 2 ​ σ v M = 9414.8 + 5649.1 + 3389.6 = 18453.5 ≈ 135.84 MPa \sigma_{vM} = \sqrt{9414.8 + 5649.1 + 3389.6} = \sqrt{18453.5} \approx 135.84\,\text{MPa} σ v M ​ = 9414.8 + 5649.1 + 3389.6 ​ = 18453.5 ​ ≈ 135.84 MPa

Safety factor against yielding: F S = S y σ v M = 420 MPa 135.84 MPa ≈ 3.09 FS = \frac{S_y}{\sigma_{vM}} = \frac{420\,\text{MPa}}{135.84\,\text{MPa}} \approx 3.09 FS = σ v M ​ S y ​ ​ = 135.84 MPa 420 MPa ​ ≈ 3.09

The hub operates safely within the elastic regime.

Step 3: Torque Transmission Capacity T = 1 2 π μ p d 2 L = 1 2 π ( 0.15 ) ( 58.22 × 10 6 N/m 2 ) ( 0.080 m ) 2 ( 0.100 m ) T = \frac{1}{2} \pi \mu p d^2 L = \frac{1}{2} \pi (0.15) (58.22 \times 10^6\,\text{N/m}^2) (0.080\,\text{m})^2 (0.100\,\text{m}) T = 2 1 ​ π μ p d 2 L = 2 1 ​ π ( 0.15 ) ( 58.22 × 1 0 6 N/m 2 ) ( 0.080 m ) 2 ( 0.100 m ) T = 0.5 × π × 0.15 × 58.22 × 10 6 × 0.0064 × 0.100 ≈ 8780 N ⋅ m = 8.78 kN ⋅ m T = 0.5 \times \pi \times 0.15 \times 58.22 \times 10^6 \times 0.0064 \times 0.100 \approx 8780\,\text{N}\cdot\text{m} = 8.78\,\text{kN}\cdot\text{m} T = 0.5 × π × 0.15 × 58.22 × 1 0 6 × 0.0064 × 0.100 ≈ 8780 N ⋅ m = 8.78 kN ⋅ m

Step 4: Thermal Assembly Temperature

Total diametral expansion required: Δ d total = δ + δ clearance = 0.060 mm + 0.040 mm = 0.100 mm = 1.0 × 10 − 4 m \Delta d_{\text{total}} = \delta + \delta_{\text{clearance}} = 0.060\,\text{mm} + 0.040\,\text{mm} = 0.100\,\text{mm} = 1.0 \times 10^{-4}\,\text{m} Δ d total ​ = δ + δ clearance ​ = 0.060 mm + 0.040 mm = 0.100 mm = 1.0 × 1 0 − 4 m

Required temperature differential Δ T \Delta T Δ T : Δ T = Δ d total α d = 1.0 × 10 − 4 m ( 11.7 × 10 − 6 / ∘ C ) ( 0.080 m ) = 1.0 × 10 − 4 9.36 × 10 − 7 ≈ 106.8 ∘ C \Delta T = \frac{\Delta d_{\text{total}}}{\alpha d} = \frac{1.0 \times 10^{-4}\,\text{m}}{(11.7 \times 10^{-6}\;/^\circ\text{C})(0.080\,\text{m})} = \frac{1.0 \times 10^{-4}}{9.36 \times 10^{-7}} \approx 106.8^\circ\text{C} Δ T = α d Δ d total ​ ​ = ( 11.7 × 1 0 − 6 / ∘ C ) ( 0.080 m ) 1.0 × 1 0 − 4 m ​ = 9.36 × 1 0 − 7 1.0 × 1 0 − 4 ​ ≈ 106. 8 ∘ C

Required hub heating temperature: T hub = T ambient + Δ T = 20 ∘ C + 106.8 ∘ C ≈ 127 ∘ C T_{\text{hub}} = T_{\text{ambient}} + \Delta T = 20^\circ\text{C} + 106.8^\circ\text{C} \approx 127^\circ\text{C} T hub ​ = T ambient ​ + Δ T = 2 0 ∘ C + 106. 8 ∘ C ≈ 12 7 ∘ C

Heating the hub to 127 ∘ C 127^\circ\text{C} 12 7 ∘ C ( 261 ∘ F 261^\circ\text{F} 26 1 ∘ F ) allows effortless slip-fit over the cold shaft.