Study guide
10.3 Belts, Roller Chains & Flexible Drives
PE Mechanical: Machine Design and Materials Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology
1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety
2 Chapter 2: Physical & Mechanical Properties of Engineering Materials
2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep
3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections
3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis
4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects
4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses
5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics
5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics
6 Chapter 6: Fatigue Analysis & Dynamic Failure
6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage
7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints
7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors
8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding
8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding
9 Chapter 9: Power Transmission: Shafts & Gearing
9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing
10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers
10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels
11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems
11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods
12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power
12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics
13 Chapter 13: Kinematics, Mechatronics & Control Systems
13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls
14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods
14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly
15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion
15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
10.3 Belts, Roller Chains & Flexible Drives
Key Takeaways Explain This Topic AI
V-belts multiply effective friction through the groove wedging factor 1 / sin ( β / 2 ) 1/\sin(\beta/2) 1/ sin ( β /2 ) , allowing substantially higher tension ratios ( F 1 − m v 2 ) / ( F 2 − m v 2 ) = exp [ f ϕ / sin ( β / 2 ) ] (F_1 - m v^2)/(F_2 - m v^2) = \exp[f\phi / \sin(\beta/2)] ( F 1 − m v 2 ) / ( F 2 − m v 2 ) = exp [ f ϕ / sin ( β /2 )] and lower required shaft bearing preloads than flat belts.
Roller chain sprockets exhibit chordal action (polygonal effect) that induces cyclic speed variations of 1 − cos ( 180 ∘ / N ) 1 - \cos(180^\circ/N) 1 − cos ( 18 0 ∘ / N ) , requiring a minimum of 17 teeth on the driving sprocket for smooth high-speed operation.
Belt drives are solved with F 1 − F 2 = P / v F_1 - F_2 = P/v F 1 − F 2 = P / v , the capstan ratio and F i = ( F 1 + F 2 ) / 2 − F c F_i = (F_1 + F_2)/2 - F_c F i = ( F 1 + F 2 ) /2 − F c ; in the worked example 7.5 kW at 14.7 m/s needed about 440 N of installation tension.
Chain length in pitches is L / p = 2 C / p + ( N 1 + N 2 ) / 2 + ( N 2 − N 1 ) 2 / ( 4 π 2 C / p ) L/p = 2C/p + (N_1 + N_2)/2 + (N_2 - N_1)^2/(4\pi^2 C/p) L / p = 2 C / p + ( N 1 + N 2 ) /2 + ( N 2 − N 1 ) 2 / ( 4 π 2 C / p ) , rounded up to an even number of links.
Last updated: October 2026
10.3 Belts, Roller Chains & Flexible Drives
Flexible drives carry power between shafts that are too far apart for gears, absorb shock, and tolerate some misalignment. The machine designer sizes them from a few relationships: the capstan (belt-friction) equation, centrifugal tension, wrap angle, belt or chain length, and, for chains, the polygonal (chordal) speed variation.
Flexible Drives: Flat Belts, V-Belts & Synchronous Belts
Flexible drive media transmit mechanical power between separated shafts through friction grip or positive mechanical toothed meshing:
Flat Belts :
Mechanics : Pure friction drive on smooth, crowned cylindrical pulleys (pulley crown ensures lateral tracking).
Characteristics : Operates at very high speeds ( > 40 m/s > 40\,\text{m/s} > 40 m/s ), quiet, absorbs shock via elastic stretch. Requires high initial tension F i F_i F i , resulting in large overhung shaft and bearing radial loads.
V-Belts :
Mechanics : Operates in trapezoidal sheave grooves with included groove angle β ≈ 34 ∘ − 40 ∘ \beta \approx 34^\circ - 40^\circ β ≈ 3 4 ∘ − 4 0 ∘ (half-angle β / 2 ≈ 17 ∘ − 20 ∘ \beta/2 \approx 17^\circ - 20^\circ β /2 ≈ 1 7 ∘ − 2 0 ∘ ).
The Wedging Effect : Lateral compression against the tapered groove sidewalls multiplies normal contact force without increasing belt tension: N = F n sin ( β / 2 ) N = \frac{F_n}{\sin(\beta/2)} N = sin ( β /2 ) F n
This multiplies effective friction by a factor of 1 / sin ( β / 2 ) ≈ 1 / sin ( 18 ∘ ) ≈ 3.23 1/\sin(\beta/2) \approx 1/\sin(18^\circ) \approx 3.23 1/ sin ( β /2 ) ≈ 1/ sin ( 1 8 ∘ ) ≈ 3.23 , delivering over three times the torque capacity of a flat belt under identical tension.
3. Synchronous (Timing) Belts :
Mechanics : Positive mechanical engagement between molded elastomeric belt teeth (trapezoidal or curvilinear HTD profile) and matching axially grooved pulleys.
Characteristics : Zero kinematic slip; maintains precise angular phase synchronization. Requires minimal initial tension, substantially reducing bearing radial loads.
Flexible Drive Comparison Matrix
- Parameter Flat Belts V-Belts Synchronous (Timing) Belts
- Drive Mechanism Friction (Smooth) Friction (Groove Wedging) Positive Mechanical Meshing
Efficiency 96 % − 98 % 96\% - 98\% 96% − 98% 93 % − 96 % 93\% - 96\% 93% − 96% 97 % − 99 % 97\% - 99\% 97% − 99%
- Kinematic Slip 1 % − 3 % 1\% - 3\% 1% − 3% creep 1 % − 2 % 1\% - 2\% 1% − 2% creep 0 % 0\% 0% (Zero Slip)
- Shaft Bearing Load High Moderate Low
Speed Capability Highest ( > 50 m/s > 50\,\text{m/s} > 50 m/s ) Moderate ( 15 − 30 m/s 15 - 30\,\text{m/s} 15 − 30 m/s ) High ( 20 − 40 m/s 20 - 40\,\text{m/s} 20 − 40 m/s )
- Alignment Sensitivity Low Low to Moderate High (Sensitive to parallelism)
- The Belt Tension Formulation
Consider a belt traveling at pitch velocity v v v (in m/s \text{m/s} m/s ) around a sheave with wrap angle ϕ \phi ϕ (in radians). As belt speed increases, centrifugal force throws the belt outward, creating a centrifugal tension F c F_c F c that reduces effective normal pressure against the sheave: F c = m v 2 F_c = m v^2 F c = m v 2
where m m m is the linear mass density of the belt (in kg/m \text{kg/m} kg/m or lbm/ft \text{lbm/ft} lbm/ft ). The governing Euler-Eytelwein capstan relationship governing limiting tight-side tension F 1 F_1 F 1 and slack-side tension F 2 F_2 F 2 is: F 1 − m v 2 F 2 − m v 2 = exp ( f ϕ sin ( β / 2 ) ) \frac{F_1 - m v^2}{F_2 - m v^2} = \exp\left( \frac{f \phi}{\sin(\beta/2)} \right) F 2 − m v 2 F 1 − m v 2 = exp ( sin ( β /2 ) f ϕ )
For flat belts, set sin ( β / 2 ) = sin ( 90 ∘ ) = 1.0 \sin(\beta/2) = \sin(90^\circ) = 1.0 sin ( β /2 ) = sin ( 9 0 ∘ ) = 1.0 , reducing the exponent to f ϕ f\phi f ϕ . For V-belts, β / 2 \beta/2 β /2 is the groove half-angle ( 17 ∘ − 20 ∘ 17^\circ - 20^\circ 1 7 ∘ − 2 0 ∘ ).
Wrap Angle Calculation
For an open belt drive with large sheave diameter D D D , small sheave diameter d d d , and center-to-center distance C C C , the wrap angle on the smaller (limiting) sheave is: ϕ = π − 2 arcsin ( D − d 2 C ) [ radians ] \phi = \pi - 2 \arcsin\left( \frac{D - d}{2 C} \right) \quad [\text{radians}] ϕ = π − 2 arcsin ( 2 C D − d ) [ radians ]
- Transmitted Power & Initial Tension
- Net Transmitted Force : F net = F 1 − F 2 F_{\text{net}} = F_1 - F_2 F net = F 1 − F 2
- Transmitted Mechanical Power ( P P P ) : P = ( F 1 − F 2 ) v P = (F_1 - F_2) v P = ( F 1 − F 2 ) v
Initial Static Installation Tension ( F i F_i F i ) (assuming linear belt elasticity): F i = F 1 + F 2 2 − F c F_i = \frac{F_1 + F_2}{2} - F_c F i = 2 F 1 + F 2 − F c
Roller Chain Drives & Chordal Action
Roller chains transmit power through positive engagement between cylindrical rollers and sprocket teeth, governed by ANSI standard B29.1:
Chain Pitch ( p p p ) : Distance between adjacent pin centers. ANSI numbering designates pitch in eighths of an inch: ANSI #40 has p = 4 / 8 in = 0.500 in p = 4/8\,\text{in} = 0.500\,\text{in} p = 4/8 in = 0.500 in ; ANSI #60 has p = 6 / 8 in = 0.750 in p = 6/8\,\text{in} = 0.750\,\text{in} p = 6/8 in = 0.750 in ; ANSI #80 has p = 8 / 8 in = 1.000 in p = 8/8\,\text{in} = 1.000\,\text{in} p = 8/8 in = 1.000 in .
Sprocket Pitch Diameter ( d d d ) :
Because chain links form a regular polygon around the sprocket: d = p sin ( 180 ∘ / N ) d = \frac{p}{\sin(180^\circ / N)} d = sin ( 18 0 ∘ / N ) p
where N N N is the number of sprocket teeth.
Chordal Action (Polygonal Effect)
As the sprocket rotates, the chain link chord swings through an arc, causing the effective pitch radius to oscillate cyclically between pitch radius R = d / 2 R = d/2 R = d /2 and inscribed radius r = R cos ( 180 ∘ / N ) r = R \cos(180^\circ / N) r = R cos ( 18 0 ∘ / N ) : Sprocket Tooth Centerline
- / \
- / \
- Link Pin -> o-----o <- Link Pin
- | p |
- | |
- +--+--+
- |
- Chordal Pitch Circle
This geometry induces a continuous cyclical variation in linear chain velocity: v max − v min v max = 1 − cos ( 180 ∘ N ) \frac{v_{\max} - v_{\min}}{v_{\max}} = 1 - \cos\left( \frac{180^\circ}{N} \right) v m a x v m a x − v m i n = 1 − cos ( N 18 0 ∘ )
With N = 10 N = 10 N = 10 teeth, linear velocity oscillates by 4.9% , causing severe chain whip, chordal impact shock, high noise, and rapid roller fatigue.
With N = 17 N = 17 N = 17 teeth, speed fluctuation drops to 1.7% .
With N = 25 N = 25 N = 25 teeth, speed fluctuation drops below 0.8% .
Important
Standard machine design guidelines dictate a minimum of 17 teeth ( N 1 ≥ 17 N_1 \ge 17 N 1 ≥ 17 ) on the smaller driving sprocket for normal industrial speeds, and N 1 ≥ 21 − 25 N_1 \ge 21 - 25 N 1 ≥ 21 − 25 for high-speed drives ( > 1 , 000 rpm > 1,000\,\text{rpm} > 1 , 000 rpm ). Single-stage speed reduction ratios should not exceed 6 : 1 6:1 6 : 1 to 7 : 1 7:1 7 : 1 .
Belt and Chain Length
For an open belt drive, the exact pitch length is L = 4 C 2 − ( D − d ) 2 + 1 2 ( D θ D + d θ d ) , θ d = π − 2 sin − 1 D − d 2 C , θ D = π + 2 sin − 1 D − d 2 C L = \sqrt{4C^2 - (D - d)^2} + \frac{1}{2}\left(D\,\theta_D + d\,\theta_d\right), \qquad \theta_d = \pi - 2\sin^{-1}\frac{D - d}{2C}, \quad \theta_D = \pi + 2\sin^{-1}\frac{D - d}{2C} L = 4 C 2 − ( D − d ) 2 + 2 1 ( D θ D + d θ d ) , θ d = π − 2 sin − 1 2 C D − d , θ D = π + 2 sin − 1 2 C D − d
and a close approximation is L ≈ 2 C + π 2 ( D + d ) + ( D − d ) 2 4 C L \approx 2C + \tfrac{\pi}{2}(D + d) + \tfrac{(D - d)^2}{4C} L ≈ 2 C + 2 π ( D + d ) + 4 C ( D − d ) 2 .
For a roller chain, the length in pitches (links) is L p = 2 C p + N 1 + N 2 2 + ( N 2 − N 1 ) 2 4 π 2 ( C / p ) \frac{L}{p} = \frac{2C}{p} + \frac{N_1 + N_2}{2} + \frac{(N_2 - N_1)^2}{4\pi^2 (C/p)} p L = p 2 C + 2 N 1 + N 2 + 4 π 2 ( C / p ) ( N 2 − N 1 ) 2
Round up to an even number of links so that no offset (half) link is needed.
- Worked Example: V-Belt Drive and Chain Selection Checks
- Part A: V-Belt Tensions
A single V-belt transmits P = 7.5 kW P = 7.5\,\text{kW} P = 7.5 kW from a d = 160 mm d = 160\,\text{mm} d = 160 mm driver sheave turning at 1,750 rpm 1{,}750\,\text{rpm} 1 , 750 rpm to a D = 400 mm D = 400\,\text{mm} D = 400 mm driven sheave. The center distance is C = 600 mm C = 600\,\text{mm} C = 600 mm , the belt mass is m = 0.20 kg/m m = 0.20\,\text{kg/m} m = 0.20 kg/m , the groove angle is β = 36 ∘ \beta = 36^\circ β = 3 6 ∘ , and f = 0.15 f = 0.15 f = 0.15 .
Belt speed: v = π d n / 60 = π ( 0.160 ) ( 1,750 ) / 60 = 14.66 m/s v = \pi d n / 60 = \pi (0.160)(1{,}750)/60 = 14.66\,\text{m/s} v = π d n /60 = π ( 0.160 ) ( 1 , 750 ) /60 = 14.66 m/s .
Wrap on the small sheave: ϕ = π − 2 sin − 1 [ ( 400 − 160 ) / ( 2 × 600 ) ] = π − 2 ( 0.2014 ) = 2.739 rad \phi = \pi - 2\sin^{-1}\!\left[(400 - 160)/(2 \times 600)\right] = \pi - 2(0.2014) = 2.739\,\text{rad} ϕ = π − 2 sin − 1 [ ( 400 − 160 ) / ( 2 × 600 ) ] = π − 2 ( 0.2014 ) = 2.739 rad ( 156.9 ∘ 156.9^\circ 156. 9 ∘ ).
Friction exponent: f ϕ / sin ( β / 2 ) = ( 0.15 ) ( 2.739 ) / sin 18 ∘ = 1.329 f\phi/\sin(\beta/2) = (0.15)(2.739)/\sin 18^\circ = 1.329 f ϕ / sin ( β /2 ) = ( 0.15 ) ( 2.739 ) / sin 1 8 ∘ = 1.329 , so the tension ratio is e 1.329 = 3.78 e^{1.329} = 3.78 e 1.329 = 3.78 .
Centrifugal tension: F c = m v 2 = 0.20 ( 14.66 ) 2 = 43.0 N F_c = m v^2 = 0.20(14.66)^2 = 43.0\,\text{N} F c = m v 2 = 0.20 ( 14.66 ) 2 = 43.0 N .
Net (effective) pull: F 1 − F 2 = P / v = 7,500 / 14.66 = 511.6 N F_1 - F_2 = P/v = 7{,}500/14.66 = 511.6\,\text{N} F 1 − F 2 = P / v = 7 , 500/14.66 = 511.6 N .
Solve ( F 1 − F c ) = 3.78 ( F 2 − F c ) (F_1 - F_c) = 3.78(F_2 - F_c) ( F 1 − F c ) = 3.78 ( F 2 − F c ) together with step 5: F 2 − F c = 511.6 / 2.78 = 184.1 N F_2 - F_c = 511.6/2.78 = 184.1\,\text{N} F 2 − F c = 511.6/2.78 = 184.1 N , giving F 2 = 227.1 N F_2 = 227.1\,\text{N} F 2 = 227.1 N and F 1 = 738.7 N F_1 = 738.7\,\text{N} F 1 = 738.7 N .
Required installation tension: F i = ( F 1 + F 2 ) / 2 − F c = 482.9 − 43.0 = 439.9 N F_i = (F_1 + F_2)/2 - F_c = 482.9 - 43.0 = 439.9\,\text{N} F i = ( F 1 + F 2 ) /2 − F c = 482.9 − 43.0 = 439.9 N .
Pitch length: 4 ( 0.6 ) 2 − ( 0.24 ) 2 + 1 2 [ 0.400 ( 3.544 ) + 0.160 ( 2.739 ) ] = 1.176 + 0.928 = 2.104 m \sqrt{4(0.6)^2 - (0.24)^2} + \tfrac{1}{2}[0.400(3.544) + 0.160(2.739)] = 1.176 + 0.928 = 2.104\,\text{m} 4 ( 0.6 ) 2 − ( 0.24 ) 2 + 2 1 [ 0.400 ( 3.544 ) + 0.160 ( 2.739 )] = 1.176 + 0.928 = 2.104 m ; the approximation gives 1.200 + 0.880 + 0.024 = 2.104 m 1.200 + 0.880 + 0.024 = 2.104\,\text{m} 1.200 + 0.880 + 0.024 = 2.104 m .
The driven sheave turns at about 1,750 × 160 / 400 = 700 rpm 1{,}750 \times 160/400 = 700\,\text{rpm} 1 , 750 × 160/400 = 700 rpm (slightly less because of belt creep), and the shafts carry a radial load of roughly F 1 + F 2 ≈ 966 N F_1 + F_2 \approx 966\,\text{N} F 1 + F 2 ≈ 966 N .
Part B: Roller Chain Length and Chordal Variation
An ANSI No. 60 chain ( p = 0.750 in p = 0.750\,\text{in} p = 0.750 in ) connects a 17-tooth driver to a 51-tooth sprocket at a center distance of C = 30 in C = 30\,\text{in} C = 30 in ( C / p = 40 C/p = 40 C / p = 40 ).
Length: L / p = 2 ( 40 ) + ( 17 + 51 ) / 2 + ( 51 − 17 ) 2 / ( 4 π 2 × 40 ) = 80 + 34 + 0.73 = 114.7 L/p = 2(40) + (17 + 51)/2 + (51 - 17)^2/(4\pi^2 \times 40) = 80 + 34 + 0.73 = 114.7 L / p = 2 ( 40 ) + ( 17 + 51 ) /2 + ( 51 − 17 ) 2 / ( 4 π 2 × 40 ) = 80 + 34 + 0.73 = 114.7 , so specify 116 links (the next even number).
Driver pitch diameter: d = p / sin ( 180 ∘ / 17 ) = 0.750 / 0.1838 = 4.08 in d = p/\sin(180^\circ/17) = 0.750/0.1838 = 4.08\,\text{in} d = p / sin ( 18 0 ∘ /17 ) = 0.750/0.1838 = 4.08 in .
Chordal speed variation: 1 − cos ( 180 ∘ / 17 ) = 1.7 % 1 - \cos(180^\circ/17) = 1.7\% 1 − cos ( 18 0 ∘ /17 ) = 1.7% , acceptable for an industrial drive.