Study guide
10.5 Electric Motors, Engines & Flywheels
PE Mechanical: Machine Design and Materials Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology
1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety
2 Chapter 2: Physical & Mechanical Properties of Engineering Materials
2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep
3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections
3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis
4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects
4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses
5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics
5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics
6 Chapter 6: Fatigue Analysis & Dynamic Failure
6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage
7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints
7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors
8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding
8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding
9 Chapter 9: Power Transmission: Shafts & Gearing
9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing
10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers
10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels
11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems
11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods
12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power
12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics
13 Chapter 13: Kinematics, Mechatronics & Control Systems
13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls
14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods
14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly
15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion
15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
10.5 Electric Motors, Engines & Flywheels
Key Takeaways Explain This Topic AI
Induction-motor synchronous speed is n s = 120 f / p n_s = 120 f/p n s = 120 f / p (1,800 rpm for a 4-pole, 60 Hz motor) and slip s = ( n s − n ) / n s s = (n_s - n)/n_s s = ( n s − n ) / n s is typically a few percent at full load.
NEMA Design B is the general-purpose motor; Design C gives high starting torque and Design D gives at least 2.75 times full-load starting torque with 5% or more slip for flywheel and hoist duty.
Load inertia reflects to the motor as J l o a d / i 2 J_{load}/i^2 J l o a d / i 2 , and acceleration time is t = J t o t a l Δ ω / ( T m o t o r − T l o a d ) t = J_{total}\Delta\omega/(T_{motor} - T_{load}) t = J t o t a l Δ ω / ( T m o t or − T l o a d ) .
Engine brake mean effective pressure is bmep = P b n R / ( V d N ) \text{bmep} = P_b n_R/(V_d N) bmep = P b n R / ( V d N ) with n R = 2 n_R = 2 n R = 2 for four-stroke engines.
A flywheel is sized from I = Δ E / ( C s ω a v g 2 ) I = \Delta E/(C_s \omega_{avg}^2) I = Δ E / ( C s ω a vg 2 ) ; allowable C s C_s C s ranges from about 0.2 for crushers to below 0.01 for generators.
Last updated: October 2026
10.5 Electric Motors, Engines & Flywheels
Every drive train starts at a prime mover . The machine designer does not design the motor or engine, but must choose one whose torque-speed behavior suits the load, size the shafts and couplings for its torque, check that it can start and accelerate the load, and smooth out torque that fluctuates during each cycle. This section covers the motor and engine relationships that appear in machine design problems.
1. Three-Phase Induction Motors
The squirrel-cage induction motor is the workhorse of industrial machinery.
Synchronous speed depends only on supply frequency f f f and the number of poles p p p : n s = 120 f p [ rpm ] n_s = \frac{120 f}{p} \quad [\text{rpm}] n s = p 120 f [ rpm ]
At 60 Hz 60\,\text{Hz} 60 Hz : 2-pole = 3,600 = 3{,}600 = 3 , 600 , 4-pole = 1,800 = 1{,}800 = 1 , 800 , 6-pole = 1,200 = 1{,}200 = 1 , 200 , 8-pole = 900 rpm = 900\,\text{rpm} = 900 rpm (at 50 Hz 50\,\text{Hz} 50 Hz : 3,000 3{,}000 3 , 000 , 1,500 1{,}500 1 , 500 , 1,000 1{,}000 1 , 000 , 750 750 750 ).
Slip is the fractional lag of the rotor behind the rotating field: s = ( n s − n ) / n s s = (n_s - n)/n_s s = ( n s − n ) / n s . Full-load slip of general-purpose motors is typically a few percent, which is why a 4-pole nameplate reads about 1,750 1{,}750 1 , 750 to 1,780 rpm 1{,}780\,\text{rpm} 1 , 780 rpm .
Torque from power and speed : T [ lb ⋅ ft ] = 5,252 hp n , T [ N ⋅ m ] = 9,549 P [ kW ] n T\,[\text{lb}\cdot\text{ft}] = \frac{5{,}252\,\text{hp}}{n}, \qquad T\,[\text{N}\cdot\text{m}] = \frac{9{,}549\,P\,[\text{kW}]}{n} T [ lb ⋅ ft ] = n 5 , 252 hp , T [ N ⋅ m ] = n 9 , 549 P [ kW ]
Electrical input for a three-phase motor is P in = 3 V L I L pf P_{\text{in}} = \sqrt{3}\,V_L I_L\,\text{pf} P in = 3 V L I L pf , and shaft output is P out = η P in P_{\text{out}} = \eta P_{\text{in}} P out = η P in .
NEMA Design Letters (Torque-Speed Character)
- NEMA design Starting (locked-rotor) torque Starting current Full-load slip Typical loads
- A Normal High Under 5% Machine tools, fans (special cases)
- B Normal Normal Under 5% General purpose: pumps, fans, conveyors; the most common design
- C High (about 2 to 2.5 times full-load torque) Normal Under 5% Loaded conveyors, reciprocating compressors
D Very high (at least 2.75 times full-load torque) Low to normal 5% or more Punch presses with flywheels, hoists, cranes
Additional selection points:
Starting current of an across-the-line (direct-on-line) start is commonly about 6 to 7 times full-load current. Soft starters, reduced-voltage starters and variable-frequency drives limit it.
Service factor (commonly 1.15 1.15 1.15 for general-purpose motors) is the continuous overload the motor tolerates at rated voltage and frequency, at the cost of higher winding temperature and shorter insulation life. It is a margin, not a rating to size to.
Efficiency : NEMA Premium (IE3) efficiency levels are the federal minimum for most general-purpose motors under the US Department of Energy rules in 10 CFR Part 431.
Variable-frequency drives (VFDs) change speed by changing frequency. Below base speed they hold volts per hertz constant, giving constant torque capability; above base speed the voltage is limited, so the motor runs at constant power with falling torque. Self-cooled motors lose cooling at low speed, which limits continuous low-speed torque.
Other motor types, such as synchronous, DC, brushless servo and stepper motors, are covered with mechatronics in Section 13.2.
- 2. Matching the Motor to the Load
- Load Characteristics
Constant-torque loads (conveyors, positive-displacement pumps, hoists) need the same torque at every speed, so power rises in proportion to speed.
Variable-torque loads (centrifugal fans and pumps) follow the affinity laws: flow ∝ n \propto n ∝ n , pressure or torque ∝ n 2 \propto n^2 ∝ n 2 , power ∝ n 3 \propto n^3 ∝ n 3 . Slowing a fan 20 % 20\% 20% cuts its power to about 0.8 3 = 51 % 0.8^3 = 51\% 0. 8 3 = 51% .
Constant-power loads (winders, machine-tool spindles) need high torque at low speed and low torque at high speed.
Reflected Inertia and Acceleration Time
Through a speed reducer with ratio i = n motor / n load i = n_{\text{motor}}/n_{\text{load}} i = n motor / n load and efficiency η \eta η , load quantities seen at the motor shaft are J reflected = J load i 2 , T load,reflected = T load i η J_{\text{reflected}} = \frac{J_{\text{load}}}{i^2}, \qquad T_{\text{load,reflected}} = \frac{T_{\text{load}}}{i\,\eta} J reflected = i 2 J load , T load,reflected = i η T load
The time to accelerate from rest to speed ω \omega ω is t = J total Δ ω T motor,avg − T load,reflected t = \frac{J_{\text{total}}\,\Delta\omega}{T_{\text{motor,avg}} - T_{\text{load,reflected}}} t = T motor,avg − T load,reflected J total Δ ω
where J total J_{\text{total}} J total includes the motor rotor, couplings and the reflected load inertia. The gear ratio that gives the fastest acceleration of a pure inertia load is i = J load / J motor i = \sqrt{J_{\text{load}}/J_{\text{motor}}} i = J load / J motor (inertia matching).
3. Internal Combustion Engines
Brake power is measured at the output shaft: P b = 2 π N T P_b = 2\pi N T P b = 2 π NT with N N N in rev/s. Indicated power is developed on the pistons, and mechanical efficiency is η m = P b / P i \eta_m = P_b / P_i η m = P b / P i .
Brake mean effective pressure is a size-independent measure of how hard an engine works: bmep = P b n R V d N \text{bmep} = \frac{P_b\,n_R}{V_d\,N} bmep = V d N P b n R
where V d V_d V d is the total displaced volume, N N N is in rev/s, and n R = 2 n_R = 2 n R = 2 for four-stroke or 1 1 1 for two-stroke engines.
Brake thermal efficiency is η t h = P b / ( m ˙ f Q H V ) \eta_{th} = P_b / (\dot{m}_f\,Q_{HV}) η t h = P b / ( m ˙ f Q H V ) , and brake specific fuel consumption is bsfc = m ˙ f / P b \text{bsfc} = \dot{m}_f / P_b bsfc = m ˙ f / P b .
The air-standard Otto cycle sets an ideal limit: η = 1 − 1 / r k − 1 \eta = 1 - 1/r^{\,k-1} η = 1 − 1/ r k − 1 . With compression ratio r = 10 r = 10 r = 10 and k = 1.4 k = 1.4 k = 1.4 , η = 1 − 10 − 0.4 = 0.60 \eta = 1 - 10^{-0.4} = 0.60 η = 1 − 1 0 − 0.4 = 0.60 ; real spark-ignition engines achieve far less.
Engine output torque pulses with each firing stroke, so engine-driven machinery needs flywheels, torsionally soft couplings or torsional vibration dampers, and drivetrain shafts must be checked for fluctuating torque ( T a ≠ 0 T_a \ne 0 T a = 0 ).
4. Flywheels
A flywheel stores kinetic energy E = 1 2 I ω 2 E = \tfrac{1}{2} I \omega^2 E = 2 1 I ω 2 so that a machine with fluctuating demand (punch press, crusher, reciprocating compressor) or fluctuating supply (engine) runs at nearly constant speed. Define the coefficient of speed fluctuation C s = ω max − ω min ω avg , ω avg ≈ ω max + ω min 2 C_s = \frac{\omega_{\max} - \omega_{\min}}{\omega_{\text{avg}}}, \qquad \omega_{\text{avg}} \approx \frac{\omega_{\max} + \omega_{\min}}{2} C s = ω avg ω m a x − ω m i n , ω avg ≈ 2 ω m a x + ω m i n
The energy that must be absorbed or released between the speed extremes is Δ E = 1 2 I ( ω max 2 − ω min 2 ) = I ω avg 2 C s ⟹ I = Δ E C s ω avg 2 \Delta E = \tfrac{1}{2} I (\omega_{\max}^2 - \omega_{\min}^2) = I\,\omega_{\text{avg}}^2\,C_s \quad \Longrightarrow \quad I = \frac{\Delta E}{C_s\,\omega_{\text{avg}}^2} Δ E = 2 1 I ( ω m a x 2 − ω m i n 2 ) = I ω avg 2 C s ⟹ I = C s ω avg 2 Δ E
Allowable C s C_s C s ranges from about 0.2 0.2 0.2 for crushers and hammering machinery down to well below 0.01 0.01 0.01 for electrical generators. A rim-type flywheel stores most of its inertia in the rim ( I ≈ m r 2 I \approx m r^2 I ≈ m r 2 ), while a solid disk has I = 1 2 m r 2 I = \tfrac{1}{2} m r^2 I = 2 1 m r 2 . The rim's hoop stress, roughly σ ≈ ρ v 2 \sigma \approx \rho v^2 σ ≈ ρ v 2 for a thin rotating ring, limits the safe rim speed.
- 5. Worked Example: Motor, Drive and Flywheel Checks
- Part A: Induction Motor Data
A 4-pole, 60 Hz 60\,\text{Hz} 60 Hz , 460 V 460\,\text{V} 460 V motor is rated 15 hp 15\,\text{hp} 15 hp at 1,760 rpm 1{,}760\,\text{rpm} 1 , 760 rpm , with full-load efficiency 92.4 % 92.4\% 92.4% and power factor 0.86 0.86 0.86 .
Synchronous speed and slip: n s = 120 ( 60 ) / 4 = 1,800 rpm n_s = 120(60)/4 = 1{,}800\,\text{rpm} n s = 120 ( 60 ) /4 = 1 , 800 rpm ; s = ( 1,800 − 1,760 ) / 1,800 = 2.22 % s = (1{,}800 - 1{,}760)/1{,}800 = 2.22\% s = ( 1 , 800 − 1 , 760 ) /1 , 800 = 2.22% .
Full-load torque: T = 5,252 ( 15 ) / 1,760 = 44.8 lb ⋅ ft T = 5{,}252(15)/1{,}760 = 44.8\,\text{lb}\cdot\text{ft} T = 5 , 252 ( 15 ) /1 , 760 = 44.8 lb ⋅ ft ( 60.7 N ⋅ m 60.7\,\text{N}\cdot\text{m} 60.7 N ⋅ m ).
Electrical input: P in = 15 ( 0.7457 ) / 0.924 = 12.11 kW P_{\text{in}} = 15(0.7457)/0.924 = 12.11\,\text{kW} P in = 15 ( 0.7457 ) /0.924 = 12.11 kW .
Line current: I = 12,110 / ( 3 × 460 × 0.86 ) = 17.7 A I = 12{,}110/(\sqrt{3} \times 460 \times 0.86) = 17.7\,\text{A} I = 12 , 110/ ( 3 × 460 × 0.86 ) = 17.7 A .
Part B: Reflected Inertia and Acceleration
The motor drives a conveyor pulley through a 10 : 1 10{:}1 10 : 1 reducer. The pulley and belt have J load = 12 kg ⋅ m 2 J_{\text{load}} = 12\,\text{kg}\cdot\text{m}^2 J load = 12 kg ⋅ m 2 , and the rotor has J motor = 0.08 kg ⋅ m 2 J_{\text{motor}} = 0.08\,\text{kg}\cdot\text{m}^2 J motor = 0.08 kg ⋅ m 2 .
Reflected load inertia: 12 / 10 2 = 0.12 kg ⋅ m 2 12/10^2 = 0.12\,\text{kg}\cdot\text{m}^2 12/1 0 2 = 0.12 kg ⋅ m 2 , so J total = 0.20 kg ⋅ m 2 J_{\text{total}} = 0.20\,\text{kg}\cdot\text{m}^2 J total = 0.20 kg ⋅ m 2 .
If the motor supplies an average of 60 N ⋅ m 60\,\text{N}\cdot\text{m} 60 N ⋅ m more than the reflected load torque during starting, reaching 1,760 rpm 1{,}760\,\text{rpm} 1 , 760 rpm ( 184.3 rad/s 184.3\,\text{rad/s} 184.3 rad/s ) takes t = 0.20 ( 184.3 ) / 60 = 0.61 s t = 0.20(184.3)/60 = 0.61\,\text{s} t = 0.20 ( 184.3 ) /60 = 0.61 s .
Part C: Punch-Press Flywheel
A press needs Δ E = 3,000 J \Delta E = 3{,}000\,\text{J} Δ E = 3 , 000 J per stroke from its flywheel, which averages 300 rpm 300\,\text{rpm} 300 rpm ( ω avg = 31.42 rad/s \omega_{\text{avg}} = 31.42\,\text{rad/s} ω avg = 31.42 rad/s ) with C s = 0.10 C_s = 0.10 C s = 0.10 . I = Δ E C s ω avg 2 = 3,000 0.10 ( 31.42 ) 2 = 3,000 98.70 = 30.4 kg ⋅ m 2 I = \frac{\Delta E}{C_s\,\omega_{\text{avg}}^2} = \frac{3{,}000}{0.10 (31.42)^2} = \frac{3{,}000}{98.70} = 30.4\,\text{kg}\cdot\text{m}^2 I = C s ω avg 2 Δ E = 0.10 ( 31.42 ) 2 3 , 000 = 98.70 3 , 000 = 30.4 kg ⋅ m 2
A thin steel rim at r = 0.50 m r = 0.50\,\text{m} r = 0.50 m needs about m = I / r 2 = 122 kg m = I/r^2 = 122\,\text{kg} m = I / r 2 = 122 kg . The speed swings about ± 5 % \pm 5\% ± 5% (roughly 285 285 285 to 315 rpm 315\,\text{rpm} 315 rpm ), the rim speed is v = 31.42 ( 0.50 ) = 15.7 m/s v = 31.42(0.50) = 15.7\,\text{m/s} v = 31.42 ( 0.50 ) = 15.7 m/s , and the rim hoop stress is only about ρ v 2 = 7,850 ( 15.7 ) 2 = 1.9 MPa \rho v^2 = 7{,}850(15.7)^2 = 1.9\,\text{MPa} ρ v 2 = 7 , 850 ( 15.7 ) 2 = 1.9 MPa .