Study guide
10.2 Hydrodynamic Journal Bearings & Lubrication Regimes
PE Mechanical: Machine Design and Materials Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology
1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety
2 Chapter 2: Physical & Mechanical Properties of Engineering Materials
2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep
3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections
3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis
4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects
4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses
5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics
5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics
6 Chapter 6: Fatigue Analysis & Dynamic Failure
6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage
7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints
7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors
8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding
8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding
9 Chapter 9: Power Transmission: Shafts & Gearing
9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing
10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers
10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels
11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems
11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods
12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power
12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics
13 Chapter 13: Kinematics, Mechatronics & Control Systems
13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls
14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods
14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly
15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion
15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
10.2 Hydrodynamic Journal Bearings & Lubrication Regimes
Key Takeaways Explain This Topic AI
The Stribeck curve characterizes lubrication regimes as a function of the dimensionless parameter μ N / P \mu N / P μ N / P , transitioning from boundary lubrication ( f ≈ 0.08 − 0.15 f \approx 0.08 - 0.15 f ≈ 0.08 − 0.15 ) through mixed lubrication to full hydrodynamic lubrication ( f ≈ 0.001 − 0.005 f \approx 0.001 - 0.005 f ≈ 0.001 − 0.005 ).
Petroff's equation T f = 2 π 2 μ n r 3 L c T_f = \frac{2\pi^2 \mu n r^3 L}{c} T f = c 2 π 2 μ n r 3 L defines friction torque for a lightly loaded, concentric journal bearing, demonstrating that fluid shear friction scales with the cube of journal radius.
The dimensionless Sommerfeld number S = ( r / c ) 2 ( μ n / P ) S = (r/c)^2 (\mu n / P) S = ( r / c ) 2 ( μ n / P ) encapsulates all operational variables and dictates the eccentricity ratio ϵ = e / c \epsilon = e/c ϵ = e / c and minimum film thickness h 0 = c ( 1 − ϵ ) h_0 = c(1 - \epsilon) h 0 = c ( 1 − ϵ ) .
Raimondi-Boyd charts determine bearing performance variables: minimum film thickness ratio h 0 / c h_0/c h 0 / c , friction variable ( r / c ) f (r/c)f ( r / c ) f , flow variable Q / ( r c n L ) Q/(r c n L) Q / ( rc n L ) , and side-leakage ratio Q s / Q Q_s/Q Q s / Q .
Thermal equilibrium requires balancing viscous shear heat generation H gen = 2 π T f n H_{\text{gen}} = 2\pi T_f n H gen = 2 π T f n with lubricant thermal convection H diss = ρ Q eff c p Δ T H_{\text{diss}} = \rho Q_{\text{eff}} c_p \Delta T H diss = ρ Q eff c p Δ T , where the effective circulating flow is Q eff = Q ( 1 − 0.5 Q s / Q ) Q_{\text{eff}} = Q(1 - 0.5 Q_s/Q) Q eff = Q ( 1 − 0.5 Q s / Q ) .
Last updated: October 2026
10.2 Hydrodynamic Journal Bearings & Lubrication Regimes
Hydrodynamic journal bearings (also termed sleeve or fluid-film bearings) are standard support elements in high-speed, heavy-duty rotating machinery such as steam and gas turbines, centrifugal compressors, automotive crankshafts, and electric power generators. Unlike rolling-element bearings that have finite fatigue lives, hydrodynamic bearings operate with complete physical separation between the journal and sleeve surfaces via a continuous, pressurized viscous fluid wedge. Under steady full-film operation, surface wear is virtually non-existent, and vibration damping is exceptionally high.
Lubrication Regimes & The Stribeck Curve
The fundamental operating state of any lubricated sliding interface is characterized by the Stribeck curve , which plots the coefficient of friction f f f as a function of the bearing characteristic parameter μ N P \frac{\mu N}{P} P μ N (or μ ω P \frac{\mu \omega}{P} P μ ω ), where μ \mu μ is dynamic viscosity, N N N is rotational speed, and P P P is unit load: Friction
- Coeff (f)
- ^
- 0.15 | +----------------+
- | | Boundary |\
- 0.10 | | Lubrication | \
- | +----------------+ \
- 0.05 | \ +-------------+
- | \ | Mixed / | +---------------------+
- | \_| Thin-Film | /| Hydrodynamic (Full) |
- 0.00 |----------------------------+-------------+-/-+---------------------+--->
- 0 (Knee) mu * N / P
- 1. Boundary Lubrication
Mechanics : Occurs at very low speeds, high unit loads, or low lubricant viscosity (e.g., during startup, shutdown, or shock overloads). The fluid film is thinner than the composite surface roughness ( h 0 < R a h_0 < R_a h 0 < R a ).
Friction & Wear : High friction coefficient ( f ≈ 0.08 − 0.15 f \approx 0.08 - 0.15 f ≈ 0.08 − 0.15 ). High metallic asperity contact occurs. Wear prevention relies entirely on chemical boundary additives (such as zinc dialkyldithiophosphate / ZDDP or sulfur-phosphorus extreme-pressure [EP] compounds) that form low-shear sacrificial films on metal surfaces.
2. Mixed (Thin-Film) Lubrication
Mechanics : An intermediate transition zone where the hydrodynamic fluid pressure supports a substantial portion of the applied load, but isolated high asperity peaks still intermittently contact.
Friction & Wear : The friction coefficient drops precipitously toward a minimum "knee point" ( f ≈ 0.005 − 0.02 f \approx 0.005 - 0.02 f ≈ 0.005 − 0.02 ). Highly unstable; a minor reduction in speed or viscosity can trigger boundary wear.
3. Hydrodynamic (Full-Film / Thick-Film) Lubrication
Mechanics : Occurs at high speeds, moderate unit loads, and adequate viscosity. A continuous viscous fluid wedge completely separates the journal and sleeve ( h 0 > 3 − 5 R a h_0 > 3 - 5 R_a h 0 > 3 − 5 R a ).
Friction & Wear : Ultra-low friction ( f ≈ 0.001 − 0.005 f \approx 0.001 - 0.005 f ≈ 0.001 − 0.005 ). Zero metal-to-metal contact; theoretical component life is infinite barring contamination or thermal breakdown. Friction is governed strictly by internal viscous shear stress in the lubricant ( τ = μ d u / d y \tau = \mu \, du/dy τ = μ d u / d y ). As μ N / P \mu N / P μ N / P increases beyond the knee point, friction coefficient rises linearly due to viscous drag.
4. Elastohydrodynamic Lubrication (EHL)
Mechanics : A specialized regime occurring in non-conformal concentrated contacts (e.g., ball/roller bearings, gear meshes, cam-follower pairs).
Characteristics : Extreme localized contact pressures ( 1 − 3 GPa 1 - 3\,\text{GPa} 1 − 3 GPa ) cause two phenomena simultaneously: (a) elastic deflection of the mating metallic surfaces, and (b) an exponential increase in lubricant viscosity by three to four orders of magnitude via the Barus equation ( μ = μ 0 e α p p \mu = \mu_0 e^{\alpha_p p} μ = μ 0 e α p p ). A microscopic fluid film ( 0.1 − 1.0 μ m 0.1 - 1.0\,\mu\text{m} 0.1 − 1.0 μ m ) is preserved.
Journal Bearing Geometry & Operational Parameters
Consider a journal of diameter d d d (radius r = d / 2 r = d/2 r = d /2 ) rotating inside a cylindrical bearing sleeve of internal diameter D D D (radius R = D / 2 R = D/2 R = D /2 ) with axial length L L L :
- Radial Clearance ( c c c ) : c = R − r c = R - r c = R − r
- Diametral Clearance ( c d c_d c d ) : c d = D − d = 2 c c_d = D - d = 2c c d = D − d = 2 c
Typical industrial clearance ratios range from c / r = 0.001 c/r = 0.001 c / r = 0.001 to 0.002 0.002 0.002 ( 1 1 1 to 2 mil 2\,\text{mil} 2 mil of radial clearance per inch of journal diameter).
Nominal Bearing Unit Pressure ( P P P ) :
Defined over the projected area A p = L ⋅ d A_p = L \cdot d A p = L ⋅ d under steady radial load W W W : P = W L ⋅ d = W 2 r L P = \frac{W}{L \cdot d} = \frac{W}{2 r L} P = L ⋅ d W = 2 r L W
Length-to-Diameter Ratio ( L / d L/d L / d ) :
Standard bearings typically use L / d L/d L / d between 0.5 0.5 0.5 and 1.5 1.5 1.5 . High-speed modern turbomachinery designs favor compact ratios ( L / d = 0.5 − 0.8 L/d = 0.5 - 0.8 L / d = 0.5 − 0.8 ) to reduce parasitic friction torque and minimize sensitivity to shaft slope/angular misalignment, at the expense of higher end-leakage flow.
Petroff's Classical Friction Formulation
Petroff's equation provides a foundational baseline for friction torque by assuming a lightly loaded, concentric journal ( ϵ = 0 \epsilon = 0 ϵ = 0 ) running at constant rotational frequency n n n (in rev/s \text{rev/s} rev/s ):
Journal surface speed: U = 2 π r n U = 2\pi r n U = 2 π r n
Velocity gradient across uniform radial clearance c c c : d u d y = U c = 2 π r n c \frac{du}{dy} = \frac{U}{c} = \frac{2\pi r n}{c} d y d u = c U = c 2 π r n
- Newton's law of viscosity yields shear stress: τ = μ 2 π r n c \tau = \mu \frac{2\pi r n}{c} τ = μ c 2 π r n
- Wetted surface area: A = 2 π r L A = 2\pi r L A = 2 π r L
The total viscous shear friction force F f F_f F f is: F f = τ A = ( μ 2 π r n c ) ( 2 π r L ) = 4 π 2 μ n r 2 L c F_f = \tau A = \left( \mu \frac{2\pi r n}{c} \right) (2\pi r L) = \frac{4\pi^2 \mu n r^2 L}{c} F f = τ A = ( μ c 2 π r n ) ( 2 π r L ) = c 4 π 2 μ n r 2 L
Friction torque T f T_f T f about the journal rotational axis is: T f = F f ⋅ r = 2 π 2 μ n r 3 L c T_f = F_f \cdot r = \frac{2\pi^2 \mu n r^3 L}{c} T f = F f ⋅ r = c 2 π 2 μ n r 3 L
Dividing friction force by normal load W = P ( 2 r L ) W = P (2 r L) W = P ( 2 r L ) yields Petroff's coefficient of friction f f f : f = F f W = 2 π 2 ( μ n P ) ( r c ) f = \frac{F_f}{W} = 2\pi^2 \left( \frac{\mu n}{P} \right) \left( \frac{r}{c} \right) f = W F f = 2 π 2 ( P μ n ) ( c r )
Tip
Petroff's equation demonstrates that friction torque scales with the cube of the radius ( r 3 r^3 r 3 ). Reducing journal diameter provides the most potent lever for lowering parasitic horsepower loss in high-speed bearings.
Hydrodynamic Lubrication Theory & Reynolds Equation
When a journal bearing supports a substantial radial load W W W , the journal shifts eccentrically within the clearance space by distance e e e (center-to-center displacement). This eccentricity establishes a converging fluid wedge in the direction of journal rotation. Bearing Sleeve (Center Ob)
- /-------------\
- / \
- | Journal |
- | (Center Oj) |
- | (->) |
- \ e / /
- \--/----------/
- h_0 (Minimum Film)
Fluid drawn into this converging wedge is compressed, developing hydrodynamic pressure governed by the classical 2D Reynolds equation for incompressible thin-film flow: ∂ ∂ x ( h 3 μ ∂ p ∂ x ) + ∂ ∂ z ( h 3 μ ∂ p ∂ z ) = 6 U ∂ h ∂ x \frac{\partial}{\partial x}\left( \frac{h^3}{\mu} \frac{\partial p}{\partial x} \right) + \frac{\partial}{\partial z}\left( \frac{h^3}{\mu} \frac{\partial p}{\partial z} \right) = 6 U \frac{\partial h}{\partial x} ∂ x ∂ ( μ h 3 ∂ x ∂ p ) + ∂ z ∂ ( μ h 3 ∂ z ∂ p ) = 6 U ∂ x ∂ h
where x = r θ x = r\theta x = r θ is the circumferential coordinate, z z z is the axial coordinate, and h ( θ ) = c ( 1 + ϵ cos θ ) h(\theta) = c(1 + \epsilon \cos\theta) h ( θ ) = c ( 1 + ϵ cos θ ) is the local oil film thickness.
Key Hydrodynamic Variables
Eccentricity Ratio ( ϵ \epsilon ϵ ) : ϵ = e c ( 0 ≤ ϵ < 1 ) \epsilon = \frac{e}{c} \quad (0 \le \epsilon < 1) ϵ = c e ( 0 ≤ ϵ < 1 )
Minimum Oil Film Thickness ( h 0 h_0 h 0 ) :
Occurs at the line of centers downstream of the load line: h 0 = c − e = c ( 1 − ϵ ) h_0 = c - e = c(1 - \epsilon) h 0 = c − e = c ( 1 − ϵ )
Attitude Angle ( ϕ \phi ϕ ) : The angle between the applied radial load vector W W W and the centerline connecting bearing and journal centers.
The Sommerfeld Number ( S S S )
The Sommerfeld number (bearing characteristic number) is a dimensionless parameter that encapsulates all geometric, kinematic, and operational variables: S = ( r c ) 2 ( μ n P ) S = \left( \frac{r}{c} \right)^2 \left( \frac{\mu n}{P} \right) S = ( c r ) 2 ( P μ n )
where n n n is rotational frequency in rev/s \text{rev/s} rev/s ( n = N rpm / 60 n = N_{\text{rpm}}/60 n = N rpm /60 ), μ \mu μ is dynamic viscosity in Pa ⋅ s \text{Pa}\cdot\text{s} Pa ⋅ s ( N ⋅ s/m 2 \text{N}\cdot\text{s/m}^2 N ⋅ s/m 2 ), and P = W / ( 2 r L ) P = W/(2 r L) P = W / ( 2 r L ) is unit load in Pa \text{Pa} Pa . In US customary units, S = ( r / c ) 2 ( μ n / P ) S = (r/c)^2 (\mu n / P) S = ( r / c ) 2 ( μ n / P ) where μ \mu μ is in reyns \text{reyns} reyns ( lbf ⋅ s/in 2 \text{lbf}\cdot\text{s/in}^2 lbf ⋅ s/in 2 ) and P P P is in psi \text{psi} psi .
Raimondi-Boyd Design Methodology
Because closed-form analytical solutions to the 2D Reynolds equation with axial side leakage do not exist, modern engineering design relies on numerical solutions developed by Raimondi and Boyd. These charts relate the Sommerfeld number S S S and aspect ratio L / d L/d L / d to four primary dimensionless performance variables:
- Film Thickness Variable : h 0 c \frac{h_0}{c} c h 0
- Friction Variable : ( r c ) f \left( \frac{r}{c} \right) f ( c r ) f
- Flow Variable : Q r c n L \frac{Q}{r c n L} rc n L Q
- Side-Leakage Ratio : Q s Q \frac{Q_s}{Q} Q Q s
Representative Raimondi-Boyd Data for L / d = 1 L/d = 1 L / d = 1 (Full 360 ∘ 360^\circ 36 0 ∘ Journal Bearing)
Eccentricity ϵ \epsilon ϵ Film Ratio h 0 / c h_0 / c h 0 / c Sommerfeld Number S S S Friction Variable ( r / c ) f (r/c)f ( r / c ) f Flow Variable Q / ( r c n L ) Q / (r c n L) Q / ( rc n L ) Side-Leakage Ratio Q s / Q Q_s / Q Q s / Q
- 0.1 0.1 0.1 0.9 0.9 0.9 1.33 1.33 1.33 26.4 26.4 26.4 3.37 3.37 3.37 0.150 0.150 0.150
- 0.2 0.2 0.2 0.8 0.8 0.8 0.631 0.631 0.631 12.8 12.8 12.8 3.59 3.59 3.59 0.280 0.280 0.280
- 0.4 0.4 0.4 0.6 0.6 0.6 0.264 0.264 0.264 5.79 5.79 5.79 3.99 3.99 3.99 0.497 0.497 0.497
- 0.6 0.6 0.6 0.4 0.4 0.4 0.121 0.121 0.121 3.22 3.22 3.22 4.33 4.33 4.33 0.680 0.680 0.680
- 0.8 0.8 0.8 0.2 0.2 0.2 0.0446 0.0446 0.0446 1.70 1.70 1.70 4.62 4.62 4.62 0.842 0.842 0.842
- 0.9 0.9 0.9 0.1 0.1 0.1 0.0188 0.0188 0.0188 1.05 1.05 1.05 4.74 4.74 4.74 0.919 0.919 0.919
(Raimondi and Boyd's finite-bearing solutions as tabulated in Shigley. At light loads the friction variable approaches Petroff's value 2 π 2 S 2\pi^2 S 2 π 2 S , a quick check on any chart reading. Interpolate between rows or read the charts for intermediate S S S .)
Trumpler's Design Criteria for Safe Operation
To ensure structural integrity and prevent seizure under real-world industrial tolerances, design practice (per P.R. Trumpler) mandates:
Minimum Film Thickness : h 0 ≥ 0.0002 in + 0.00004 d h_0 \ge 0.0002\,\text{in} + 0.00004 d h 0 ≥ 0.0002 in + 0.00004 d (or h 0 ≥ 5 − 10 μ m h_0 \ge 5 - 10\,\mu\text{m} h 0 ≥ 5 − 10 μ m for precision shafts) to clear circulating particulate contamination.
Maximum Lubricant Temperature : Peak film temperature T max ≤ 120 ∘ C T_{\max} \le 120^\circ\text{C} T m a x ≤ 12 0 ∘ C ( 250 ∘ F 250^\circ\text{F} 25 0 ∘ F ) to prevent thermal oxidation and additive breakdown of mineral oils.
Overload Design Factor : N L ≥ 2.0 N_L \ge 2.0 N L ≥ 2.0 , ensuring that doubling the operational load will not reduce h 0 h_0 h 0 below critical asperity contact.
Thermal Equilibrium & Lubricant Heat Balance
Viscous shearing within the oil film generates continuous thermal energy that must be carried away by circulating oil flow. In steady-state operation, thermal equilibrium requires: H gen = H diss H_{\text{gen}} = H_{\text{diss}} H gen = H diss
1. Heat Generation Rate ( H gen H_{\text{gen}} H gen ) H gen = 2 π T f n = W f U = W f ( 2 π r n ) [ Watts ] H_{\text{gen}} = 2\pi T_f n = W f U = W f (2\pi r n) \quad [\text{Watts}] H gen = 2 π T f n = W f U = W f ( 2 π r n ) [ Watts ]
2. Heat Dissipation Rate ( H diss H_{\text{diss}} H diss )
Lubricant pumped through the bearing carries thermal energy away via end leakage and circulating flow. Using the effective volumetric flow rate Q eff Q_{\text{eff}} Q eff : Q eff = Q ( 1 − 0.5 Q s Q ) Q_{\text{eff}} = Q \left( 1 - 0.5 \frac{Q_s}{Q} \right) Q eff = Q ( 1 − 0.5 Q Q s ) H diss = m ˙ eff c p Δ T = ρ Q eff c p Δ T H_{\text{diss}} = \dot{m}_{\text{eff}} c_p \Delta T = \rho Q_{\text{eff}} c_p \Delta T H diss = m ˙ eff c p Δ T = ρ Q eff c p Δ T
where ρ \rho ρ is lubricant density (typically 850 − 900 kg/m 3 850 - 900\,\text{kg/m}^3 850 − 900 kg/m 3 ), c p c_p c p is specific heat capacity (typically 1 , 800 − 2 , 100 J/(kg ⋅ ∘ C) 1,800 - 2,100\,\text{J/(kg}\cdot^\circ\text{C)} 1 , 800 − 2 , 100 J/(kg ⋅ ∘ C) ), and Δ T = T out − T in \Delta T = T_{\text{out}} - T_{\text{in}} Δ T = T out − T in is the lubricant temperature rise.
Equating H gen = H diss H_{\text{gen}} = H_{\text{diss}} H gen = H diss yields the temperature rise formulation: Δ T = H gen ρ Q eff c p \Delta T = \frac{H_{\text{gen}}}{\rho Q_{\text{eff}} c_p} Δ T = ρ Q eff c p H gen
Iterative Viscosity Convergence
Because dynamic viscosity μ \mu μ decreases exponentially with temperature according to the ASTM D341 / Walther relationship, bearing analysis requires iterative convergence:
Assume an initial average film temperature: T avg = T in + Δ T / 2 T_{\text{avg}} = T_{\text{in}} + \Delta T / 2 T avg = T in + Δ T /2 .
Determine dynamic viscosity μ \mu μ at T avg T_{\text{avg}} T avg from the lubricant's viscosity-temperature chart.
Compute Sommerfeld number S S S , look up ( r / c ) f (r/c)f ( r / c ) f and flow parameters, and compute resulting Δ T calc \Delta T_{\text{calc}} Δ T calc .
Update T avg,new = T in + Δ T calc / 2 T_{\text{avg,new}} = T_{\text{in}} + \Delta T_{\text{calc}} / 2 T avg,new = T in + Δ T calc /2 . Repeat until T avg T_{\text{avg}} T avg converges within ± 0.5 ∘ C \pm 0.5^\circ\text{C} ± 0. 5 ∘ C .
- Worked Engineering Example: Steam Turbine Governor Shaft Bearing
- Problem Statement
A full hydrodynamic journal bearing ( 360 ∘ 360^\circ 36 0 ∘ ) supports the governor rotor shaft of an industrial steam turbine under the following specifications:
Journal diameter: d = 50 mm d = 50\,\text{mm} d = 50 mm ( r = 25 mm = 0.025 m r = 25\,\text{mm} = 0.025\,\text{m} r = 25 mm = 0.025 m )
Bearing length: L = 50 mm = 0.050 m L = 50\,\text{mm} = 0.050\,\text{m} L = 50 mm = 0.050 m ( L / d = 1.0 L/d = 1.0 L / d = 1.0 )
Radial load: W = 3 , 600 N W = 3,600\,\text{N} W = 3 , 600 N ( 3.6 kN 3.6\,\text{kN} 3.6 kN )
Rotational speed: N = 1 , 800 rpm ⟹ n = 30 rev/s N = 1,800\,\text{rpm} \implies n = 30\,\text{rev/s} N = 1 , 800 rpm ⟹ n = 30 rev/s ( U = 2 π r n = 4.7124 m/s U = 2\pi r n = 4.7124\,\text{m/s} U = 2 π r n = 4.7124 m/s )
Radial clearance: c = 0.025 mm = 25 μ m c = 0.025\,\text{mm} = 25\,\mu\text{m} c = 0.025 mm = 25 μ m ( r / c = 1 , 000 r/c = 1,000 r / c = 1 , 000 )
Lubricant: ISO VG 32 turbine oil. At the assumed average film temperature (about 50 ∘ C 50^\circ\text{C} 5 0 ∘ C ), dynamic viscosity is μ = 0.020 Pa ⋅ s \mu = 0.020\,\text{Pa}\cdot\text{s} μ = 0.020 Pa ⋅ s ( 20 cP 20\,\text{cP} 20 cP )
Oil properties: density ρ = 860 kg/m 3 \rho = 860\,\text{kg/m}^3 ρ = 860 kg/m 3 , specific heat c p = 2 , 000 J/(kg ⋅ ∘ C) c_p = 2,000\,\text{J/(kg}\cdot^\circ\text{C)} c p = 2 , 000 J/(kg ⋅ ∘ C)
Inlet oil supply temperature: T in = 35.0 ∘ C T_{\text{in}} = 35.0^\circ\text{C} T in = 35. 0 ∘ C
Determine:
The bearing nominal unit pressure P P P .
The Sommerfeld number S S S .
The minimum oil film thickness h 0 h_0 h 0 and compare against Trumpler's minimum criterion.
The coefficient of friction f f f , friction torque T f T_f T f , and total heat generation rate H gen H_{\text{gen}} H gen .
The total volumetric oil flow rate Q Q Q , side-leakage flow Q s Q_s Q s , and lubricant temperature rise Δ T \Delta T Δ T .
Step-by-Step Solution
Step 1: Compute Nominal Bearing Pressure ( P P P ) P = W L ⋅ d = 3 , 600 N ( 0.050 m ) ( 0.050 m ) = 3 , 600 0.0025 = 1 , 440 , 000 Pa = 1.44 MPa P = \frac{W}{L \cdot d} = \frac{3,600\,\text{N}}{(0.050\,\text{m})(0.050\,\text{m})} = \frac{3,600}{0.0025} = 1,440,000\,\text{Pa} = 1.44\,\text{MPa} P = L ⋅ d W = ( 0.050 m ) ( 0.050 m ) 3 , 600 N = 0.0025 3 , 600 = 1 , 440 , 000 Pa = 1.44 MPa
Step 2: Calculate the Sommerfeld Number ( S S S ) S = ( r c ) 2 ( μ n P ) = ( 1 , 000 ) 2 ⋅ ( 0.020 Pa ⋅ s ) ( 30 s − 1 ) 1.44 × 10 6 Pa = 10 6 ⋅ 0.60 1.44 × 10 6 = 0.4167 ≈ 0.417 S = \left( \frac{r}{c} \right)^2 \left( \frac{\mu n}{P} \right) = (1,000)^2 \cdot \frac{(0.020\,\text{Pa}\cdot\text{s})(30\,\text{s}^{-1})}{1.44 \times 10^6\,\text{Pa}} = 10^6 \cdot \frac{0.60}{1.44 \times 10^6} = 0.4167 \approx 0.417 S = ( c r ) 2 ( P μ n ) = ( 1 , 000 ) 2 ⋅ 1.44 × 1 0 6 Pa ( 0.020 Pa ⋅ s ) ( 30 s − 1 ) = 1 0 6 ⋅ 1.44 × 1 0 6 0.60 = 0.4167 ≈ 0.417
Step 3: Evaluate Film Thickness & Trumpler's Criterion
S = 0.417 S = 0.417 S = 0.417 falls between the ϵ = 0.2 \epsilon = 0.2 ϵ = 0.2 row ( S = 0.631 S = 0.631 S = 0.631 ) and the ϵ = 0.4 \epsilon = 0.4 ϵ = 0.4 row ( S = 0.264 S = 0.264 S = 0.264 ). Interpolating linearly on S S S , the operating point lies a fraction ( 0.417 − 0.264 ) / ( 0.631 − 0.264 ) = 0.416 (0.417 - 0.264)/(0.631 - 0.264) = 0.416 ( 0.417 − 0.264 ) / ( 0.631 − 0.264 ) = 0.416 of the way toward the ϵ = 0.2 \epsilon = 0.2 ϵ = 0.2 row:
Eccentricity ratio: ϵ ≈ 0.4 − 0.416 ( 0.2 ) = 0.32 \epsilon \approx 0.4 - 0.416(0.2) = 0.32 ϵ ≈ 0.4 − 0.416 ( 0.2 ) = 0.32
Minimum film thickness variable: h 0 / c = 1 − ϵ ≈ 0.68 h_0/c = 1 - \epsilon \approx 0.68 h 0 / c = 1 − ϵ ≈ 0.68
Compute minimum film thickness h 0 h_0 h 0 : h 0 = c ⋅ 0.68 = ( 25 μ m ) ( 0.68 ) = 17.0 μ m = 0.017 mm h_0 = c \cdot 0.68 = (25\,\mu\text{m})(0.68) = 17.0\,\mu\text{m} = 0.017\,\text{mm} h 0 = c ⋅ 0.68 = ( 25 μ m ) ( 0.68 ) = 17.0 μ m = 0.017 mm
Check against Trumpler's criterion ( h 0 , min ≥ 0.0002 in + 0.00004 d ≈ 0.005 mm + 0.00004 d h_{0,\min} \ge 0.0002\text{ in} + 0.00004 d \approx 0.005\,\text{mm} + 0.00004 d h 0 , m i n ≥ 0.0002 in + 0.00004 d ≈ 0.005 mm + 0.00004 d ): h 0 , min = 0.005 + 0.00004 ( 50 ) = 0.005 + 0.002 = 0.007 mm = 7.0 μ m h_{0,\min} = 0.005 + 0.00004(50) = 0.005 + 0.002 = 0.007\,\text{mm} = 7.0\,\mu\text{m} h 0 , m i n = 0.005 + 0.00004 ( 50 ) = 0.005 + 0.002 = 0.007 mm = 7.0 μ m
Since h 0 = 17.0 μ m > 7.0 μ m h_0 = 17.0\,\mu\text{m} > 7.0\,\mu\text{m} h 0 = 17.0 μ m > 7.0 μ m , the film comfortably separates the surfaces.
Step 4: Compute Friction, Torque, and Heat Generation
Interpolating the friction variable the same way: ( r c ) f ≈ 5.79 + 0.416 ( 12.8 − 5.79 ) = 8.7 \left( \frac{r}{c} \right) f \approx 5.79 + 0.416(12.8 - 5.79) = 8.7 ( c r ) f ≈ 5.79 + 0.416 ( 12.8 − 5.79 ) = 8.7
(Petroff's concentric estimate, 2 π 2 S = 8.2 2\pi^2 S = 8.2 2 π 2 S = 8.2 , confirms the magnitude.) The coefficient of friction is: f = 8.7 r / c = 8.7 1,000 = 0.0087 f = \frac{8.7}{r/c} = \frac{8.7}{1{,}000} = 0.0087 f = r / c 8.7 = 1 , 000 8.7 = 0.0087
Friction force and torque: F f = f ⋅ W = ( 0.0087 ) ( 3,600 N ) = 31.3 N F_f = f \cdot W = (0.0087)(3{,}600\,\text{N}) = 31.3\,\text{N} F f = f ⋅ W = ( 0.0087 ) ( 3 , 600 N ) = 31.3 N T f = F f ⋅ r = ( 31.3 N ) ( 0.025 m ) = 0.783 N ⋅ m T_f = F_f \cdot r = (31.3\,\text{N})(0.025\,\text{m}) = 0.783\,\text{N}\cdot\text{m} T f = F f ⋅ r = ( 31.3 N ) ( 0.025 m ) = 0.783 N ⋅ m
Friction heat generation rate: H gen = 2 π T f n = 2 π ( 0.783 N ⋅ m ) ( 30 s − 1 ) = 147.6 W H_{\text{gen}} = 2\pi T_f n = 2\pi (0.783\,\text{N}\cdot\text{m})(30\,\text{s}^{-1}) = 147.6\,\text{W} H gen = 2 π T f n = 2 π ( 0.783 N ⋅ m ) ( 30 s − 1 ) = 147.6 W
(Alternatively: H gen = F f ⋅ U = 31.3 × 4.7124 = 147.6 W H_{\text{gen}} = F_f \cdot U = 31.3 \times 4.7124 = 147.6\,\text{W} H gen = F f ⋅ U = 31.3 × 4.7124 = 147.6 W .)
Step 5: Compute Oil Flow Rates and Temperature Rise
Interpolating the flow variables:
Flow variable: Q r c n L ≈ 3.99 − 0.416 ( 0.40 ) = 3.82 \dfrac{Q}{r c n L} \approx 3.99 - 0.416(0.40) = 3.82 rc n L Q ≈ 3.99 − 0.416 ( 0.40 ) = 3.82
Side-leakage ratio: Q s Q ≈ 0.497 − 0.416 ( 0.217 ) = 0.41 \dfrac{Q_s}{Q} \approx 0.497 - 0.416(0.217) = 0.41 Q Q s ≈ 0.497 − 0.416 ( 0.217 ) = 0.41
Total volumetric flow rate: Q = 3.82 × ( 0.025 m ) × ( 2.5 × 10 − 5 m ) × ( 30 s − 1 ) × ( 0.050 m ) = 3.58 × 10 − 6 m 3 /s ≈ 0.215 L/min Q = 3.82 \times (0.025\,\text{m}) \times (2.5 \times 10^{-5}\,\text{m}) \times (30\,\text{s}^{-1}) \times (0.050\,\text{m}) = 3.58 \times 10^{-6}\,\text{m}^3\text{/s} \approx 0.215\,\text{L/min} Q = 3.82 × ( 0.025 m ) × ( 2.5 × 1 0 − 5 m ) × ( 30 s − 1 ) × ( 0.050 m ) = 3.58 × 1 0 − 6 m 3 /s ≈ 0.215 L/min
Side leakage flow: Q s = 0.41 × 3.58 × 10 − 6 = 1.47 × 10 − 6 m 3 /s Q_s = 0.41 \times 3.58 \times 10^{-6} = 1.47 \times 10^{-6}\,\text{m}^3\text{/s} Q s = 0.41 × 3.58 × 1 0 − 6 = 1.47 × 1 0 − 6 m 3 /s
Effective circulating flow carrying heat (half of the side flow is assumed to leave at the inlet temperature): Q eff = Q ( 1 − 0.5 Q s Q ) = 3.58 × 10 − 6 × ( 1 − 0.205 ) = 2.85 × 10 − 6 m 3 /s Q_{\text{eff}} = Q \left( 1 - 0.5 \frac{Q_s}{Q} \right) = 3.58 \times 10^{-6} \times (1 - 0.205) = 2.85 \times 10^{-6}\,\text{m}^3\text{/s} Q eff = Q ( 1 − 0.5 Q Q s ) = 3.58 × 1 0 − 6 × ( 1 − 0.205 ) = 2.85 × 1 0 − 6 m 3 /s
Mass flow rate: m ˙ eff = ρ Q eff = ( 860 ) ( 2.85 × 10 − 6 ) = 2.449 × 10 − 3 kg/s \dot{m}_{\text{eff}} = \rho Q_{\text{eff}} = (860)(2.85 \times 10^{-6}) = 2.449 \times 10^{-3}\,\text{kg/s} m ˙ eff = ρ Q eff = ( 860 ) ( 2.85 × 1 0 − 6 ) = 2.449 × 1 0 − 3 kg/s
Lubricant temperature rise: Δ T = H gen m ˙ eff c p = 147.6 W ( 2.449 × 10 − 3 ) ( 2,000 ) = 147.6 4.897 = 30.1 ∘ C \Delta T = \frac{H_{\text{gen}}}{\dot{m}_{\text{eff}} c_p} = \frac{147.6\,\text{W}}{(2.449 \times 10^{-3})(2{,}000)} = \frac{147.6}{4.897} = 30.1^\circ\text{C} Δ T = m ˙ eff c p H gen = ( 2.449 × 1 0 − 3 ) ( 2 , 000 ) 147.6 W = 4.897 147.6 = 30. 1 ∘ C
The average film temperature is T avg = T in + Δ T / 2 = 35.0 + 15.1 = 50.1 ∘ C T_{\text{avg}} = T_{\text{in}} + \Delta T / 2 = 35.0 + 15.1 = 50.1^\circ\text{C} T avg = T in + Δ T /2 = 35.0 + 15.1 = 50. 1 ∘ C . ISO VG 32 oil is roughly 0.018 0.018 0.018 to 0.020 Pa ⋅ s 0.020\,\text{Pa}\cdot\text{s} 0.020 Pa ⋅ s near 50 ∘ C 50^\circ\text{C} 5 0 ∘ C , consistent with the assumed μ = 0.020 Pa ⋅ s \mu = 0.020\,\text{Pa}\cdot\text{s} μ = 0.020 Pa ⋅ s , so this trial is essentially converged. Had T avg T_{\text{avg}} T avg come out noticeably different, the viscosity would be re-read at the new temperature and Steps 2 to 5 repeated.