Study guide
15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
PE Mechanical: Machine Design and Materials Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Basic Engineering Practice: Drawings, Economics & Design Methodology
1.1 Engineering Terms, Symbols, Drawing Interpretation & Conventions 1.2 Project Management & Engineering Economics 1.3 Design Methodology, Risk Assessment & Safety
2 Chapter 2: Physical & Mechanical Properties of Engineering Materials
2.1 Stress-Strain Relationships & Fundamental Mechanical Properties 2.2 Physical Properties, Temperature Effects, Hardness, Impact Toughness & Creep
3 Chapter 3: Mechanics of Materials: Fundamental Loadings & Deflections
3.1 Axial Loading, Normal Stress & Statically Indeterminate Members 3.2 Direct Shear, Bearing & Transverse Shear in Beams 3.3 Torsion of Shafts, Power Transmission & Thin-Walled Tubes 3.4 Beam Bending Stresses & Deflection Analysis
4 Chapter 4: Mechanics of Materials: Stability, Multiaxial Stress & Thermal Effects
4.1 Column Buckling & Elastic/Inelastic Instability 4.2 Combined Loading, Principal Stresses & Mohr's Circle 4.3 Thermal Stresses & Interference Stresses
5 Chapter 5: Failure Theories: Static Yielding & Fracture Mechanics
5.1 Static Failure Theories for Ductile Materials: von Mises & Tresca 5.2 Static Failure Theories for Brittle Materials & Fracture Mechanics
6 Chapter 6: Fatigue Analysis & Dynamic Failure
6.1 High-Cycle Fatigue, S-N Curves & Marin Modifying Factors 6.2 Fluctuating Stresses, Failure Criteria & Cumulative Damage
7 Chapter 7: Mechanical Attachments: Fasteners & Bolted Joints
7.1 Threaded Fasteners, Proof Strength & Preload Mechanics 7.2 Bolted Joint Stiffness, External Loading & Separation 7.3 Non-Threaded Fasteners: Keys, Pins, Clevises, Retaining Rings, Rivets, Lugs & Anchors
8 Chapter 8: Mechanical Attachments: Permanent Joints & Bonding
8.1 Welded Joints & Weld Group Stress Analysis 8.2 Brazing, Soldering & Structural Adhesive Bonding
9 Chapter 9: Power Transmission: Shafts & Gearing
9.1 Transmission Shaft Design, Critical Speeds & Deflection 9.2 Spur Gears: Geometry, Kinematics & AGMA Stress Equations 9.3 Helical, Bevel & Worm Gearing
10 Chapter 10: Power Transmission: Bearings, Flexible Drives, Friction Devices & Prime Movers
10.1 Rolling-Element Bearings & L10 Life Calculations 10.2 Hydrodynamic Journal Bearings & Lubrication Regimes 10.3 Belts, Roller Chains & Flexible Drives 10.4 Clutches, Brakes & Power Screws 10.5 Electric Motors, Engines & Flywheels
11 Chapter 11: Mechanical Components: Pressure Vessels & Structural Systems
11.1 Pressure Vessels & Piping: Thin and Thick Walls, ASME VIII and B31 11.2 Mechanical Springs: Helical, Belleville & Leaf Springs 11.3 Structural Trusses, Rigid Frames & Energy Methods
12 Chapter 12: Mechanical Dynamics, Vibrations & Fluid Power
12.1 Single-Degree-of-Freedom Vibrations & Resonance 12.2 Vibration Isolation, Multi-DOF Systems & Transmissibility 12.3 Fluid Power Systems: Hydraulics & Pneumatics
13 Chapter 13: Kinematics, Mechatronics & Control Systems
13.1 Mechanism Kinematics, Linkages, Cams & Simple Machines 13.2 Basic Mechatronics, Sensors & Closed-Loop Controls
14 Chapter 14: Supportive Knowledge: Fits, Tolerances & Manufacturing Methods
14.1 Limits, Fits & Geometric Dimensioning & Tolerancing (GD&T) 14.2 Manufacturing Methods, Machinability, Heat Treatment & Assembly
15 Chapter 15: Supportive Knowledge: Codes, Computation, Testing & Corrosion
15.1 Engineering Codes & Standards 15.2 Computational Methods: FEA & Numerical Analysis 15.3 Instrumentation, Testing, Inspection & Quality 15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
Key Takeaways Explain This Topic AI
Electrochemical corrosion requires an anode, cathode, electrolyte, and metallic path; galvanic corrosion is severely aggravated when an unfavorable area ratio exists (small anode coupled to a large cathode).
Austenitic stainless steels held between about 425 and 815 °C (as in weld heat-affected zones) sensitize and suffer intergranular attack; L grades such as 304L or stabilized grades such as 321 and 347 prevent it.
Hydrogen embrittlement causes delayed brittle fracture of high-strength steels (roughly above 39 HRC); plated parts are baked promptly after plating to drive out hydrogen.
Corrosion rate from coupon weight loss is mpy = 534 W / ( ρ A t ) \text{mpy} = 534W/(\rho A t) mpy = 534 W / ( ρ A t ) with W in mg, A in in² and t in hours; the corrosion allowance equals rate times design life.
Last updated: October 2026
15.4 Chemical Processes: Corrosion, Oxidation & Embrittlement
Chemical and electrochemical attack is one of the most common ways machinery deteriorates in service. The blueprint groups these processes under chemical processes: aqueous corrosion, high-temperature oxidation and the embrittlement mechanisms that turn ductile metals brittle. A designer must recognize each mechanism, estimate its rate, and choose materials, coatings or details that prevent it.
Electrochemical Corrosion Mechanics & Prevention
Metallic corrosion is an electrochemical process that oxidizes refined metals back to low-energy mineral compounds.
The Four Essentials of an Electrochemical Corrosion Cell
An electrochemical corrosion cell requires four concurrent components:
Anode : The metallic site where oxidation occurs, shedding electrons into the metal and dissolving metal ions into the solution ( M → M z + + z e − M \rightarrow M^{z+} + z e^- M → M z + + z e − ).
Cathode : The metallic site where reduction occurs, consuming electrons supplied by the anode (e.g., oxygen reduction O 2 + 2 H 2 O + 4 e − → 4 O H − O_2 + 2H_2O + 4e^- \rightarrow 4OH^- O 2 + 2 H 2 O + 4 e − → 4 O H − in neutral water, or hydrogen evolution 2 H + + 2 e − → H 2 2H^+ + 2e^- \rightarrow H_2 2 H + + 2 e − → H 2 in acids).
Electrolyte : An electrically conductive liquid (e.g., moisture, saltwater, soil) that conducts current via ionic transport.
Metallic Path : Direct electrical connection transferring electrons from the anode to the cathode.
Caution
Removing any one of these four elements stops that electrochemical cell. Coatings eliminate the electrolyte; insulating bushings break the metallic path; cathodic protection turns the entire structure into a cathode.
Galvanic Corrosion & The Critical Area Ratio Effect
When two electrochemically dissimilar metals are in electrical contact within an electrolyte, a galvanic cell develops. The more active (anodic) metal corrodes preferentially, while the more noble (cathodic) metal is protected. Galvanic Series in Seawater (Active → Noble): \text{Galvanic Series in Seawater (Active } \rightarrow \text{ Noble):} Galvanic Series in Seawater (Active → Noble): Mg → Zn → Al Alloys → Carbon Steel → Cast Iron → 304/316 SS (Active) → Brass/Bronze → Copper → Nickel → Titanium → Gold \text{Mg} \rightarrow \text{Zn} \rightarrow \text{Al Alloys} \rightarrow \text{Carbon Steel} \rightarrow \text{Cast Iron} \rightarrow \text{304/316 SS (Active)} \rightarrow \text{Brass/Bronze} \rightarrow \text{Copper} \rightarrow \text{Nickel} \rightarrow \text{Titanium} \rightarrow \text{Gold} Mg → Zn → Al Alloys → Carbon Steel → Cast Iron → 304/316 SS (Active) → Brass/Bronze → Copper → Nickel → Titanium → Gold
The Area Ratio Rule :
The rate of galvanic penetration at the anode depends directly on the cathode-to-anode surface area ratio: i anode = i cathode ( A cathode A anode ) i_{\text{anode}} = i_{\text{cathode}} \left( \frac{A_{\text{cathode}}}{A_{\text{anode}}} \right) i anode = i cathode ( A anode A cathode )
Dangerous Configuration : A small anode coupled to a large cathode (e.g., carbon steel rivets fastening large stainless steel plates). The large cathode draws massive total reduction current, forcing extreme localized current density onto the small anode, causing rapid perforation.
Acceptable Configuration : A large anode coupled to a small cathode (e.g., stainless steel fasteners joining large carbon steel structural beams).
Specific Corrosion Morphologies
Pitting Corrosion : Autocatalytic localized attack where passive oxide films (e.g., on 304/316 stainless steel) break down in chloride ( C l − Cl^- C l − ) environments. The pit interior becomes an anode; restricted fluid exchange hydrolyzes metal ions, creating concentrated hydrochloric acid inside the pit.
Crevice Corrosion : Localized attack in stagnant micro-gaps beneath gaskets, washers, or overlapping joints. Oxygen is depleted within the crevice, establishing a differential aeration cell where the oxygen-starved crevice becomes anodic relative to the oxygenated exterior surface.
Stress Corrosion Cracking (SCC) :
Requires the simultaneous presence of three conditions: (1) a susceptible alloy, (2) a sustained tensile stress (applied or residual), and (3) a specific aggressive chemical environment.
Classical pairs: Austenitic stainless steels in hot aqueous chlorides ( > 60 ∘ C > 60^\circ\text{C} > 6 0 ∘ C ); Brass in ammonia ("season cracking"); High-strength carbon steels in hydrogen sulfide ( H 2 S H_2S H 2 S , sulfide stress cracking).
Corrosion Mitigation Strategies
Cathodic Protection (CP) :
Sacrificial Anode (Galvanic CP) : Electrically bonding a sacrificial active metal (zinc, aluminum, magnesium) to the protected structure (underground pipeline, ship hull, water heater tank). The sacrificial metal corrodes, continuously supplying protective electrons.
Impressed Current Cathodic Protection (ICCP) : Uses an external DC power supply connected between an inert anode (mixed metal oxide) and the structure, driving electrons into the structure.
Protective Coatings & Anodizing :
Barrier Coatings : Epoxy, polyurethane, and powder paints isolate metal from electrolytes.
Galvanizing : Hot-dip zinc coating on steel provides both a physical barrier and sacrificial cathodic protection at exposed scratches.
Anodizing : An electrochemical process that thickens the natural aluminum oxide ( Al 2 O 3 \text{Al}_2\text{O}_3 Al 2 O 3 ) passive layer, which is then sealed in hot deionized water or nickel acetate.
Intergranular Corrosion, Dezincification & Erosion-Corrosion
Sensitization of austenitic stainless steels : holding 300-series steels between about 425 ∘ C 425^\circ\text{C} 42 5 ∘ C and 815 ∘ C 815^\circ\text{C} 81 5 ∘ C ( 800 ∘ F 800^\circ\text{F} 80 0 ∘ F to 1,500 ∘ F 1{,}500^\circ\text{F} 1 , 50 0 ∘ F ), as in a weld heat-affected zone, precipitates chromium carbides on grain boundaries. The chromium-depleted zones next to them corrode preferentially ("weld decay"). Remedies: low-carbon L grades ( ≤ 0.03 % \le 0.03\% ≤ 0.03% C, such as 304L), titanium- or niobium-stabilized grades (321, 347), or solution annealing after welding.
Dezincification selectively removes zinc from brasses with high zinc content in some waters, leaving weak, porous copper; inhibited or low-zinc alloys avoid it.
Erosion-corrosion occurs where high-velocity or turbulent flow strips protective films (pump impellers, elbows, heat-exchanger tube inlets). Fretting corrosion is wear plus oxidation at clamped joints that slip microscopically (Section 6.1).
High-Temperature Oxidation
Above a few hundred degrees Celsius, metals react directly with oxygen to form scale. The Pilling-Bedworth ratio (oxide volume per metal volume consumed) indicates whether the scale protects: ratios between about 1 and 2 usually give an adherent, protective film (aluminum is about 1.3), ratios below 1 (magnesium, about 0.8) give porous scale, and much larger ratios build compressive stress that cracks and spalls the scale. When a protective scale controls the rate by diffusion, growth follows the parabolic law x 2 = k p t x^2 = k_p t x 2 = k p t , so doubling the exposure time increases scale thickness by only about 41 % 41\% 41% . Chromium (at least about 10.5 % 10.5\% 10.5% for stainless steels), aluminum and silicon are added to form protective Cr 2 O 3 \text{Cr}_2\text{O}_3 Cr 2 O 3 , Al 2 O 3 \text{Al}_2\text{O}_3 Al 2 O 3 or SiO 2 \text{SiO}_2 SiO 2 scales.
Embrittlement Mechanisms
Hydrogen embrittlement : atomic hydrogen from acid pickling, electroplating, welding with damp consumables, cathodic overprotection or sour ( H 2 S \text{H}_2\text{S} H 2 S ) service diffuses into steel and causes delayed brittle fracture under sustained tensile stress, often hours or days after assembly. High-strength steels (roughly above 39 HRC) are most susceptible. Plated high-strength parts are baked promptly after plating (typically around 190 ∘ C 190^\circ\text{C} 19 0 ∘ C to 220 ∘ C 220^\circ\text{C} 22 0 ∘ C for several hours), and hot-dip galvanizing of the highest-strength structural bolts (such as ASTM A490) is prohibited.
Caustic embrittlement : concentrated sodium hydroxide at boiler seams and crevices causes intergranular cracking of stressed steel.
Liquid metal embrittlement : certain liquid metals wet and penetrate grain boundaries, for example zinc on high-strength steel during welding of galvanized parts, or mercury on aluminum and brass.
Temper embrittlement : alloy steels held or slowly cooled between about 375 ∘ C 375^\circ\text{C} 37 5 ∘ C and 575 ∘ C 575^\circ\text{C} 57 5 ∘ C allow impurities (P, Sb, Sn, As) to segregate to grain boundaries, raising the ductile-to-brittle transition temperature.
Corrosion Rate and Corrosion Allowance
A weight-loss coupon test converts directly to a penetration rate: mpy = 534 W ρ A t ( W in mg , ρ in g/cm 3 , A in in 2 , t in h ) \text{mpy} = \frac{534\,W}{\rho\,A\,t} \qquad \left(W \text{ in mg},\ \rho \text{ in g/cm}^3,\ A \text{ in in}^2,\ t \text{ in h}\right) mpy = ρ A t 534 W ( W in mg , ρ in g/cm 3 , A in in 2 , t in h ) mm/y = 87.6 W ρ A t ( W in mg , ρ in g/cm 3 , A in cm 2 , t in h ) \text{mm/y} = \frac{87.6\,W}{\rho\,A\,t} \qquad \left(W \text{ in mg},\ \rho \text{ in g/cm}^3,\ A \text{ in cm}^2,\ t \text{ in h}\right) mm/y = ρ A t 87.6 W ( W in mg , ρ in g/cm 3 , A in cm 2 , t in h )
where mpy is mils (thousandths of an inch) per year. The design corrosion allowance is the expected rate times the design life, added to the pressure or structural thickness (as in the ASME vessel and piping examples of Section 11.1).
Worked example: A carbon steel coupon ( ρ = 7.87 g/cm 3 \rho = 7.87\,\text{g/cm}^3 ρ = 7.87 g/cm 3 ) with 10.0 in 2 10.0\,\text{in}^2 10.0 in 2 exposed area loses 485 mg 485\,\text{mg} 485 mg in 1,000 h 1{,}000\,\text{h} 1 , 000 h of service-water exposure. mpy = 534 ( 485 ) 7.87 ( 10.0 ) ( 1,000 ) = 258,990 78,700 = 3.29 mpy = 0.084 mm/y \text{mpy} = \frac{534(485)}{7.87(10.0)(1{,}000)} = \frac{258{,}990}{78{,}700} = 3.29\,\text{mpy} = 0.084\,\text{mm/y} mpy = 7.87 ( 10.0 ) ( 1 , 000 ) 534 ( 485 ) = 78 , 700 258 , 990 = 3.29 mpy = 0.084 mm/y
For a 20-year design life, the corrosion allowance is 20 × 0.084 = 1.67 mm 20 \times 0.084 = 1.67\,\text{mm} 20 × 0.084 = 1.67 mm (about 0.066 in 0.066\,\text{in} 0.066 in ), so a 1 / 16 in 1/16\text{ in} 1/16 in ( 1.6 mm 1.6\,\text{mm} 1.6 mm ) allowance would be marginal and 2 mm 2\,\text{mm} 2 mm is a sensible choice.