Study guide

1.4 Statics, Dynamics & Mechanical Equilibrium

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

1.4 Statics, Dynamics & Mechanical Equilibrium

Key Takeaways Explain This Topic AI

Static equilibrium requires simultaneous satisfaction of translational and rotational force balances: ∑ F = 0 \sum \mathbf{F} = 0 ∑ F = 0 and ∑ M O = 0 \sum \mathbf{M}_O = 0 ∑ M O ​ = 0 in both 2D and 3D coordinate frames.

Truss analysis uses the Method of Joints for complete member forces, the Method of Sections for targeted interior chords, and rapid visual inspection rules for identifying zero-force members.

Capstan belt friction dictates torque and brake holding capacity via Eytelwein's equation: T 2 / T 1 = e μ β T_2 / T_1 = e^{\mu \beta} T 2 ​ / T 1 ​ = e μ β , where β \beta β must be expressed strictly in radians.

Planar rigid body kinetics balances forces and moments about the center of mass ( G G G ) via ∑ F = m a G \sum \mathbf{F} = m \mathbf{a}_G ∑ F = m a G ​ and ∑ M G = I G α \sum M_G = I_G \alpha ∑ M G ​ = I G ​ α , with mass moments of inertia shifted using the Parallel Axis Theorem ( I = I G + m d 2 I = I_G + m d^2 I = I G ​ + m d 2 ).

Work-energy and impulse-momentum principles provide efficient solutions for dynamic impact, rotational spin-up, and velocity changes without integrating time-varying accelerations.

Last updated: August 2026

Statics, Dynamics & Mechanical Equilibrium

Statics and dynamics form the mechanical bedrock for machine design, structural frame integrity, mechanism kinematics, and vibration analysis. The PE Mechanical exam tests both foundational statics (equilibrium, trusses, friction, centroids) and planar rigid-body dynamics (kinematics, kinetics, work-energy, impulse-momentum).

1. Free-Body Diagrams & Static Equilibrium

A Free-Body Diagram (FBD) isolates a body or subsystem from its surroundings and depicts all external forces, applied moments, and support reaction forces. +-----------------------------------------------------------------------------------------+

  • | COMMON 2D SUPPORT REACTIONS |
  • | |
  • | SUPPORT TYPE DEGREES OF FREEDOM CONSTRAINED REACTION FORCES/MOMENTS |
  • | -------------------- ------------------------------ ----------------------- |
  • | 1. Roller / Rocker Normal translation 1 Force (perpendicular) |
  • | 2. Frictionless Guide Transverse translation 1 Force (normal to slot) |
  • | 3. Pinned Joint / Hinge Horizontal & Vertical translation 2 Forces (R_x, R_y) |
  • | 4. Fixed / Built-In All translations & rotation 2 Forces + 1 Moment (M_R) |
  • | 5. Flexible Cable / Rod Line of action along cable 1 Tension Force (axial) |
  • +-----------------------------------------------------------------------------------------+
  • Equations of Static Equilibrium

For a rigid body in static equilibrium in a 2D plane: ∑ F x = 0 , ∑ F y = 0 , ∑ M O = 0 ( about any arbitrary point O ) \sum F_x = 0, \quad \sum F_y = 0, \quad \sum M_O = 0 \quad (\text{about any arbitrary point } O) ∑ F x ​ = 0 , ∑ F y ​ = 0 , ∑ M O ​ = 0 ( about any arbitrary point O )

For 3D spatial equilibrium: ∑ F x = 0 , ∑ F y = 0 , ∑ F z = 0 \sum F_x = 0, \quad \sum F_y = 0, \quad \sum F_z = 0 ∑ F x ​ = 0 , ∑ F y ​ = 0 , ∑ F z ​ = 0 ∑ M x = 0 , ∑ M y = 0 , ∑ M z = 0 \sum M_x = 0, \quad \sum M_y = 0, \quad \sum M_z = 0 ∑ M x ​ = 0 , ∑ M y ​ = 0 , ∑ M z ​ = 0

Two-Force and Three-Force Members

Two-Force Members: A structural component with pin joints at both ends and no intermediate loads or moments applied along its length. The reaction forces at both pins must be equal in magnitude, opposite in direction, and collinear along the line connecting the two pins.

Three-Force Members: A body subjected to forces applied at only three points. For equilibrium, the lines of action of the three forces must be concurrent (intersect at a single point) or parallel.

2. Truss Analysis: Joints, Sections & Zero-Force Members

Trusses are pin-connected frameworks where all members act as axial two-force members (tension or compression). +-----------------------------------------------------------------------------------------+

  • | TRUSS ANALYSIS METHODOLOGIES |
  • | |
  • | METHOD OF JOINTS METHOD OF SECTIONS |
  • | - Isolates individual joint pins. - Cuts an imaginary plane through |
  • | - Concurrent force system (Sum F_x=0, Sum F_y=0). at most 3 unknown members. |
  • | - Ideal for finding all member forces. - Solves directly for interior |
  • | - Solves 2 unknown forces per joint. chords using Sum M = 0. |
  • +-----------------------------------------------------------------------------------------+
  • Rapid Visual Inspection Rules for Zero-Force Members

Identifying zero-force members by visual inspection eliminates unnecessary equations:

Two-Member Unloaded Joint: If two non-collinear members form an unloaded pin joint, both members carry zero force ( F 1 = 0 , F 2 = 0 F_1 = 0, F_2 = 0 F 1 ​ = 0 , F 2 ​ = 0 ).

Three-Member Joint with Two Collinear: If three members meet at an unloaded joint where two members are collinear, the third (non-collinear) member carries zero force , and the two collinear members carry equal forces.

Loaded Two-Member Joint: If two members meet at a joint with an external load aligned collinearly with one member, the other non-collinear member is a zero-force member. +-----------------------------------------------------------------------------------------+

  • | ZERO-FORCE MEMBER INSPECTION EXAMPLES |
  • | |
  • | Rule 1: Unloaded 2-Bar Joint Rule 2: 3-Bar Joint (2 Collinear, Unloaded) |
  • | (Pin Joint A) (Pin Joint B) |
  • | / \ | Member 3 = 0 |
  • | / \ v |
  • | Member 1 / \ Member 2 -----------+----------- |
  • | v v Member 1 Member 2 |
  • | F1 = 0 F2 = 0 (F1 = F2, Member 3 is Zero-Force) |
  • +-----------------------------------------------------------------------------------------+
  • 3. Coulomb Friction & Belt/Capstan Friction
  • Coulomb Dry Friction & Impending Slip

For two dry surfaces in contact with normal force N N N :

  • Static Equilibrium (No slip): F f ≤ μ s N F_f \le \mu_s N F f ​ ≤ μ s ​ N
  • Impending Motion / Maximum Static Friction: F f , max ⁡ = μ s N F_{f,\max} = \mu_s N F f , m a x ​ = μ s ​ N

Kinetic (Dynamic) Motion: F k = μ k N ( where μ k < μ s ) F_k = \mu_k N \quad (\text{where } \mu_k < \mu_s) F k ​ = μ k ​ N ( where μ k ​ < μ s ​ ) Angle of Static Friction: tan ⁡ ϕ s = μ s \text{Angle of Static Friction: } \tan \phi_s = \mu_s Angle of Static Friction: tan ϕ s ​ = μ s ​

Belt and Capstan Friction (Eytelwein's Formula)

For a flexible belt, rope, or band wrapped around a curved drum with friction coefficient μ \mu μ and total wrap angle β \beta β : T 2 T 1 = e μ β \frac{T_2}{T_1} = e^{\mu \beta} T 1 ​ T 2 ​ ​ = e μ β

Where:

T 2 = tension on the tight side (side resisting or pulling motion) T_2 = \text{tension on the tight side (side resisting or pulling motion)} T 2 ​ = tension on the tight side (side resisting or pulling motion)

T 1 = tension on the slack side ( T 2 > T 1 ) T_1 = \text{tension on the slack side } (T_2 > T_1) T 1 ​ = tension on the slack side ( T 2 ​ > T 1 ​ )

μ = coefficient of friction between belt and drum \mu = \text{coefficient of friction between belt and drum} μ = coefficient of friction between belt and drum

β = total contact angle in r a d i a n s ( β rad = θ deg × π 180 ) \beta = \text{total contact angle in } \mathbf{radians} \quad (\beta_{\text{rad}} = \theta_{\text{deg}} \times \frac{\pi}{180}) β = total contact angle in radians ( β rad ​ = θ deg ​ × 180 π ​ ) Braking Torque: τ brake = ( T 2 − T 1 ) R \text{Braking Torque: } \tau_{\text{brake}} = (T_2 - T_1) R Braking Torque: τ brake ​ = ( T 2 ​ − T 1 ​ ) R Power Transmitted: P = ( T 2 − T 1 ) v = ( T 2 − T 1 ) ( ω R ) \text{Power Transmitted: } P = (T_2 - T_1) v = (T_2 - T_1) (\omega R) Power Transmitted: P = ( T 2 ​ − T 1 ​ ) v = ( T 2 ​ − T 1 ​ ) ( ω R )

4. Centroids, Area & Mass Moments of Inertia

Composite Centroid Calculation x ˉ = ∑ A i x ˉ i ∑ A i , y ˉ = ∑ A i y ˉ i ∑ A i \bar{x} = \frac{\sum A_i \bar{x}_i}{\sum A_i}, \qquad \bar{y} = \frac{\sum A_i \bar{y}_i}{\sum A_i} x ˉ = ∑ A i ​ ∑ A i ​ x ˉ i ​ ​ , y ˉ ​ = ∑ A i ​ ∑ A i ​ y ˉ ​ i ​ ​

Parallel Axis Theorem

Area Moment of Inertia (Bending Rigidity): I x = I ˉ x ′ + A d y 2 , I y = I ˉ y ′ + A d x 2 I_x = \bar{I}_{x'} + A d_y^2, \qquad I_y = \bar{I}_{y'} + A d_x^2 I x ​ = I ˉ x ′ ​ + A d y 2 ​ , I y ​ = I ˉ y ′ ​ + A d x 2 ​

Mass Moment of Inertia (Rotational Inertia): I axis = I G + m d 2 I_{\text{axis}} = I_G + m d^2 I axis ​ = I G ​ + m d 2

Where I G I_G I G ​ is the centroidal mass moment of inertia, m m m is body mass, and d d d is the perpendicular distance between the centroidal axis and the parallel axis of rotation. +-----------------------------------------------------------------------------------------+

  • | COMMON MASS MOMENTS OF INERTIA (I_G) |
  • | |
  • | SHAPE GEOMETRY AXIS OF ROTATION FORMULA |
  • | ------------------------------ --------------------- ----------------------- |
  • | Slender Rod (Length L) Through Center (G) I_G = (1/12) * m * L^2 |
  • | Slender Rod (Length L) Through End Pivot I_end = (1/3) * m * L^2 |
  • | Solid Cylinder / Disk (Radius R) Central Polar Axis (G) I_G = (1/2) * m * R^2 |
  • | Thin Cylindrical Shell (Radius R) Central Polar Axis (G) I_G = m * R^2 |
  • | Solid Sphere (Radius R) Through Center (G) I_G = (2/5) * m * R^2 |
  • | Thin Spherical Shell (Radius R) Through Center (G) I_G = (2/3) * m * R^2 |

+-----------------------------------------------------------------------------------------+ Radius of Gyration: k = I m ⟹ I = m k 2 \text{Radius of Gyration: } k = \sqrt{\frac{I}{m}} \implies I = m k^2 Radius of Gyration: k = m I ​ ​ ⟹ I = m k 2

5. Kinematics of Particles and Rigid Bodies +-----------------------------------------------------------------------------------------+

  • | PLANAR KINEMATICS EQUATIONS |
  • | |
  • | RECTILINEAR (Constant a) ANGULAR / ROTATIONAL (Constant alpha) |
  • | v = v_0 + a * t omega = omega_0 + alpha * t |
  • | s = s_0 + v_0*t + 0.5*a*t^2 theta = theta_0 + omega_0*t + 0.5*alpha*t^2 |
  • | v^2 = v_0^2 + 2*a*(s - s_0) omega^2 = omega_0^2 + 2*alpha*(theta - theta_0) |
  • | |
  • | CURVILINEAR NORMAL-TANGENTIAL ACCELERATION: |
  • | Tangential: a_t = dv/dt = r * alpha (changes speed) |
  • | Normal: a_n = v^2 / rho = r * omega^2 (changes direction toward center) |
  • | Total Acceleration: a = sqrt(a_t^2 + a_n^2) |
  • +-----------------------------------------------------------------------------------------+
  • Relative Velocity in Rigid Bodies

For points A A A and B B B located on the same rigid body rotating with angular velocity ω \boldsymbol{\omega} ω : v B = v A + ω × r B / A \mathbf{v}_B = \mathbf{v}_A + \boldsymbol{\omega} \times \mathbf{r}_{B/A} v B ​ = v A ​ + ω × r B / A ​ a B = a A + α × r B / A − ω 2 r B / A \mathbf{a}_B = \mathbf{a}_A + \boldsymbol{\alpha} \times \mathbf{r}_{B/A} - \omega^2 \mathbf{r}_{B/A} a B ​ = a A ​ + α × r B / A ​ − ω 2 r B / A ​

6. Planar Kinetics: Force-Acceleration, Work-Energy & Impulse +-----------------------------------------------------------------------------------------+

  • | THREE KINETIC FORMULATION APPROACHES |
  • | |
  • | 1. NEWTON'S 2ND LAW (Forces & Accelerations at an instant) |
  • | Sum F_x = m * a_Gx, Sum F_y = m * a_Gy, Sum M_G = I_G * alpha |
  • | (About fixed pivot O: Sum M_O = I_O * alpha) |
  • | |
  • | 2. WORK-ENERGY THEOREM (Relates Forces to Velocity over a Distance) |
  • | T_1 + Sum U_{1->2} = T_2 |
  • | Kinetic Energy: T = 0.5 * m * v_G^2 + 0.5 * I_G * omega^2 |
  • | Spring Work: U_spring = -0.5 * k * (x_2^2 - x_1^2) |
  • | Gravity Work: U_grav = -m * g * (y_2 - y_1) |
  • | |
  • | 3. IMPULSE-MOMENTUM (Relates Forces to Velocity over a Time Interval) |
  • | Linear: m * v_1 + Integral(Sum F dt) = m * v_2 |
  • | Angular: I_G * omega_1 + Integral(Sum M_G dt) = I_G * omega_2 |
  • | (About fixed pivot O: I_O * omega_1 + Integral(Sum M_O dt) = I_O * omega_2) |
  • +-----------------------------------------------------------------------------------------+
  • Direct Central Impact and Coefficient of Restitution ( e e e )

For colliding bodies A A A and B B B along their line of impact: Conservation of Linear Momentum: m A v A 1 + m B v B 1 = m A v A 2 + m B v B 2 \text{Conservation of Linear Momentum: } m_A v_{A1} + m_B v_{B1} = m_A v_{A2} + m_B v_{B2} Conservation of Linear Momentum: m A ​ v A 1 ​ + m B ​ v B 1 ​ = m A ​ v A 2 ​ + m B ​ v B 2 ​ Coefficient of Restitution: e = v B 2 − v A 2 v A 1 − v B 1 \text{Coefficient of Restitution: } e = \frac{v_{B2} - v_{A2}}{v_{A1} - v_{B1}} Coefficient of Restitution: e = v A 1 ​ − v B 1 ​ v B 2 ​ − v A 2 ​ ​

Elastic Impact ( e = 1.0 e = 1.0 e = 1.0 ): Total kinetic energy is conserved.

Plastic / Inelastic Impact ( e = 0 e = 0 e = 0 ): Bodies stick together ( v A 2 = v B 2 v_{A2} = v_{B2} v A 2 ​ = v B 2 ​ ), maximizing energy dissipation.

7. Step-by-Step Worked Problem: Industrial Band Brake

Problem: A band brake holds a rotating drum of diameter D = 24 in. D = 24 \text{ in.} D = 24 in. ( R = 1.0 ft R = 1.0 \text{ ft} R = 1.0 ft ). The coefficient of friction between the band and drum is μ = 0.35 \mu = 0.35 μ = 0.35 . The band wraps around the drum by an angle of θ = 225 ∘ \theta = 225^\circ θ = 22 5 ∘ . The drum is rotating counterclockwise and transmitting a torque of τ = 450 ft ⋅ lbf \tau = 450 \text{ ft}\cdot\text{lbf} τ = 450 ft ⋅ lbf .

Calculate the required slack side tension T 1 T_1 T 1 ​ and tight side tension T 2 T_2 T 2 ​ to hold the load. +-----------------------------------------------------------------------------------------+

  • | BAND BRAKE STEP-BY-STEP SOLUTION |
  • | |
  • | STEP 1: Convert Wrap Angle to Radians |
  • | beta = 225 deg * (pi / 180 deg) = 3.9270 radians |
  • | |
  • | STEP 2: Compute Capstan Friction Ratio (T2 / T1) |
  • | T2 / T1 = e^(mu * beta) = e^(0.35 * 3.9270) = e^(1.37445) = 3.9529 |
  • | T2 = 3.9529 * T1 |
  • | |
  • | STEP 3: Relate Torque to Belt Tensions |
  • | Torque: tau = (T2 - T1) * R |
  • | 450 ft*lbf = (3.9529 * T1 - T1) * (1.0 ft) |
  • | 450 = 2.9529 * T1 |
  • | |
  • | STEP 4: Solve for Tensions |
  • | Slack Side Tension T1 = 450 / 2.9529 = 152.39 lbf |
  • | Tight Side Tension T2 = 3.9529 * 152.39 = 602.39 lbf |
  • | |
  • | CHECK: tau = (602.39 - 152.39) * 1.0 = 450.0 ft*lbf (Verified). |
  • +-----------------------------------------------------------------------------------------+