Study guide

1.3 Units, Dimensional Analysis & Physical Constants

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

1.3 Units, Dimensional Analysis & Physical Constants

Key Takeaways Explain This Topic AI

The PE Mechanical exam tests both International System (SI) and US Customary / English Engineering units; flawless unit conversion is essential to passing.

In the English Engineering unit system, the gravitational constant g c = 32.174 lbm ⋅ ft / ( lbf ⋅ s 2 ) g_c = 32.174 \text{ lbm}\cdot\text{ft}/(\text{lbf}\cdot\text{s}^2) g c ​ = 32.174 lbm ⋅ ft / ( lbf ⋅ s 2 ) is mandatory to reconcile mass ( lbm \text{lbm} lbm ) and force ( lbf \text{lbf} lbf ) in Newton's second law: F = m a / g c F = ma/g_c F = ma / g c ​ .

The Universal Gas Constant R u = 8.3145 kJ/(kmol ⋅ K) = 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) R_u = 8.3145 \text{ kJ/(kmol}\cdot\text{K)} = 1545.35 \text{ ft}\cdot\text{lbf/(lbmol}\cdot^\circ\text{R)} R u ​ = 8.3145 kJ/(kmol ⋅ K) = 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) , requiring specific gas constant calculations via R = R u / M R = R_u / M R = R u ​ / M .

The Buckingham Pi Theorem determines the number of independent dimensionless groups ( Π = n − k \Pi = n - k Π = n − k ) governing physical systems, forming parameters like Reynolds, Mach, and Prandtl numbers.

High-frequency unit conversion traps include mixing gauge and absolute pressures, omitting the 144 in 2 / ft 2 144 \text{ in}^2/\text{ft}^2 144 in 2 / ft 2 factor in hydraulic head formulas, and confusing dynamic versus kinematic viscosity.

Last updated: August 2026

Units, Dimensional Analysis & Physical Constants

Unit conversion errors and dimensional inconsistencies represent the single most common source of unforced calculation errors on the NCEES PE Mechanical exam. Problems are presented in both International System (SI) and US Customary (English Engineering) units, frequently mixing units within a single problem statement (e.g., pipe diameters in inches, lengths in feet, pressures in psi, flow rates in gallons per minute, and power in horsepower).

1. The Mass vs. Force Distinction: lbm \text{lbm} lbm , lbf \text{lbf} lbf , slug \text{slug} slug , and g c g_c g c ​

In SI units, mass and force are cleanly delineated through base units: 1 N = 1 kg ⋅ m/s 2 1 \text{ N} = 1 \text{ kg}\cdot\text{m/s}^2 1 N = 1 kg ⋅ m/s 2 . In English units, the historical dual use of the word "pound" for both mass and force requires absolute rigor. +-----------------------------------------------------------------------------------------+

  • | ENGLISH ENGINEERING UNIT SYSTEMS |
  • | |
  • | 1. GRAVITATIONAL SYSTEM (Slug - lbf - ft - s) |
  • | - Base mass unit: 1 slug = 32.174 lbm |
  • | - Newton's Second Law: F = m * a (where m is in slugs, F is in lbf) |
  • | - 1 lbf accelerates 1 slug at 1 ft/s^2 |
  • | |
  • | 2. DUAL POUND SYSTEM (lbm - lbf - ft - s with g_c) |
  • | - Base mass unit: pound-mass (lbm) |
  • | - Base force unit: pound-force (lbf) |
  • | - Dimensional Constant: g_c = 32.174 (lbm * ft) / (lbf * s^2) |
  • | - Newton's Second Law: F = (m * a) / g_c |
  • | - Weight on Earth (where g = 32.174 ft/s^2): W = (m * g) / g_c = m [in lbf] |
  • +-----------------------------------------------------------------------------------------+
  • Application of g c g_c g c ​ in Mechanical Engineering Formulas

Whenever a formula derives from fundamental Newtonian mechanics ( F = m a F = ma F = ma ) or energy balances and uses mass in lbm \text{lbm} lbm and force/energy in lbf \text{lbf} lbf or ft ⋅ lbf \text{ft}\cdot\text{lbf} ft ⋅ lbf , g c g_c g c ​ must be inserted in the denominator : Kinetic Energy: E k = m v 2 2 g c [ ft ⋅ lbf ] \text{Kinetic Energy: } E_k = \frac{m v^2}{2 g_c} \quad [\text{ft}\cdot\text{lbf}] Kinetic Energy: E k ​ = 2 g c ​ m v 2 ​ [ ft ⋅ lbf ] Potential Energy: E p = m g z g c [ ft ⋅ lbf ] \text{Potential Energy: } E_p = \frac{m g z}{g_c} \quad [\text{ft}\cdot\text{lbf}] Potential Energy: E p ​ = g c ​ m g z ​ [ ft ⋅ lbf ] Hydrostatic Pressure: P = ρ g h g c [ lbf/ft 2 ] \text{Hydrostatic Pressure: } P = \frac{\rho g h}{g_c} \quad [\text{lbf/ft}^2] Hydrostatic Pressure: P = g c ​ ρ g h ​ [ lbf/ft 2 ] Dynamic Pressure: q = ρ v 2 2 g c [ lbf/ft 2 ] \text{Dynamic Pressure: } q = \frac{\rho v^2}{2 g_c} \quad [\text{lbf/ft}^2] Dynamic Pressure: q = 2 g c ​ ρ v 2 ​ [ lbf/ft 2 ] Reynolds Number: R e = ρ v D μ [ where ρ is lbm ft 3 and μ is lbm ft ⋅ s ] \text{Reynolds Number: } Re = \frac{\rho v D}{\mu} \quad \left[\text{where } \rho \text{ is } \frac{\text{lbm}}{\text{ft}^3} \text{ and } \mu \text{ is } \frac{\text{lbm}}{\text{ft}\cdot\text{s}}\right] Reynolds Number: R e = μ ρ v D ​ [ where ρ is ft 3 lbm ​ and μ is ft ⋅ s lbm ​ ]

Caution

If dynamic viscosity is provided in lbf ⋅ s ft 2 \frac{\text{lbf}\cdot\text{s}}{\text{ft}^2} ft 2 lbf ⋅ s ​ , you must convert it to lbm ft ⋅ s \frac{\text{lbm}}{\text{ft}\cdot\text{s}} ft ⋅ s lbm ​ by multiplying by g c = 32.174 lbm ⋅ ft lbf ⋅ s 2 g_c = 32.174 \frac{\text{lbm}\cdot\text{ft}}{\text{lbf}\cdot\text{s}^2} g c ​ = 32.174 lbf ⋅ s 2 lbm ⋅ ft ​ , or express density ρ \rho ρ in slugs ft 3 \frac{\text{slugs}}{\text{ft}^3} ft 3 slugs ​ .

2. Master Conversion Reference Tables +-----------------------------------------------------------------------------------------+

  • | HIGH-YIELD PE CONVERSION MULTIPLIERS |
  • | |
  • | POWER: 1 hp = 550 ft*lbf/s = 33,000 ft*lbf/min = 0.7457 kW = 2,544.4 BTU/hr |
  • | 1 Ton of Refrigeration = 12,000 BTU/hr = 200 BTU/min = 3.51685 kW |
  • | 1 kW = 3,412.14 BTU/hr = 737.56 ft*lbf/s = 1.341 hp |
  • | |
  • | ENERGY: 1 BTU = 778.169 ft*lbf = 1,055.06 J = 1.05506 kJ |
  • | 1 kWh = 3,412.14 BTU = 3.6 MJ = 2.655 * 10^6 ft*lbf |
  • | |
  • | PRESSURE: 1 atm = 14.696 psia = 101.325 kPa = 1.01325 bar = 29.921 in. Hg |
  • | = 33.90 ft H2O = 406.8 in. w.g. = 760 mmHg |
  • | 1 psi = 144 psf = 2.307 ft H2O = 27.70 in. w.g. = 6.89476 kPa |
  • | 1 bar = 100 kPa = 10^5 Pa = 14.5038 psi = 0.9869 atm |
  • | 1 in. w.g. (at 60 deg F) = 0.03613 psi = 5.204 psf = 249.08 Pa |
  • | |
  • | VISCOSITY: Dynamic (mu): 1 Pa*s = 1 N*s/m^2 = 10 Poise = 1,000 cP |
  • | = 0.67197 lbm/(ft*s) = 0.020885 lbf*s/ft^2 |
  • | Kinematic (nu): 1 m^2/s = 10^4 Stokes = 10^6 cSt = 10.7639 ft^2/s |
  • +-----------------------------------------------------------------------------------------+
  • Temperature Scales and Temperature Differences

Thermodynamic equations (ideal gas law, Carnot efficiency, radiative heat transfer) require absolute temperature : T ( Kelvin ) = T ( ∘ C ) + 273.15 T(\text{Kelvin}) = T(^\circ\text{C}) + 273.15 T ( Kelvin ) = T ( ∘ C ) + 273.15 T ( Rankine ) = T ( ∘ F ) + 459.67 T(\text{Rankine}) = T(^\circ\text{F}) + 459.67 T ( Rankine ) = T ( ∘ F ) + 459.67

For temperature differences (such as Δ T \Delta T Δ T in convective heat transfer q = h A Δ T q = h A \Delta T q = h A Δ T or thermal expansion Δ L = α L Δ T \Delta L = \alpha L \Delta T Δ L = αL Δ T ): Δ T ( 1.0 K ) = Δ T ( 1.0 ∘ C ) = Δ T ( 1.8 ∘ F ) = Δ T ( 1.8 ∘ R ) \Delta T (1.0 \text{ K}) = \Delta T (1.0 ^\circ\text{C}) = \Delta T (1.8 ^\circ\text{F}) = \Delta T (1.8 ^\circ\text{R}) Δ T ( 1.0 K ) = Δ T ( 1. 0 ∘ C ) = Δ T ( 1. 8 ∘ F ) = Δ T ( 1. 8 ∘ R )

3. Fundamental Physical Constants

Constant Name Symbol SI Value & Units US Customary Value & Units

Standard Acceleration of Gravity g 0 g_0 g 0 ​ 9.80665 m/s 2 9.80665 \text{ m/s}^2 9.80665 m/s 2 32.17405 ft/s 2 32.17405 \text{ ft/s}^2 32.17405 ft/s 2

Universal Gas Constant R u R_u R u ​ 8.31446 kJ/(kmol ⋅ K) 8.31446 \text{ kJ/(kmol}\cdot\text{K)} 8.31446 kJ/(kmol ⋅ K) 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) 1545.35 \text{ ft}\cdot\text{lbf/(lbmol}\cdot^\circ\text{R)} 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) ; 1.98588 BTU/(lbmol ⋅ ∘ R) 1.98588 \text{ BTU/(lbmol}\cdot^\circ\text{R)} 1.98588 BTU/(lbmol ⋅ ∘ R)

Specific Gas Constant for Air R air R_{\text{air}} R air ​ 0.2870 kJ/(kg ⋅ K) 0.2870 \text{ kJ/(kg}\cdot\text{K)} 0.2870 kJ/(kg ⋅ K) 53.35 ft ⋅ lbf/(lbm ⋅ ∘ R) 53.35 \text{ ft}\cdot\text{lbf/(lbm}\cdot^\circ\text{R)} 53.35 ft ⋅ lbf/(lbm ⋅ ∘ R) ; 0.06855 BTU/(lbm ⋅ ∘ R) 0.06855 \text{ BTU/(lbm}\cdot^\circ\text{R)} 0.06855 BTU/(lbm ⋅ ∘ R)

Stefan-Boltzmann Constant σ \sigma σ 5.67037 × 10 − 8 W m 2 ⋅ K 4 5.67037 \times 10^{-8} \frac{\text{W}}{\text{m}^2\cdot\text{K}^4} 5.67037 × 1 0 − 8 m 2 ⋅ K 4 W ​ 0.1714 × 10 − 8 BTU hr ⋅ ft 2 ⋅ ∘ R 4 0.1714 \times 10^{-8} \frac{\text{BTU}}{\text{hr}\cdot\text{ft}^2\cdot^\circ\text{R}^4} 0.1714 × 1 0 − 8 hr ⋅ ft 2 ⋅ ∘ R 4 BTU ​

Standard Atmospheric Pressure P atm P_{\text{atm}} P atm ​ 101.325 kPa 101.325 \text{ kPa} 101.325 kPa 14.696 psia = 2116.2 psf 14.696 \text{ psia} = 2116.2 \text{ psf} 14.696 psia = 2116.2 psf

Density of Water at 39.2 ∘ F / 4 ∘ C 39.2^\circ\text{F} / 4^\circ\text{C} 39. 2 ∘ F / 4 ∘ C ρ water \rho_{\text{water}} ρ water ​ 1 , 000 kg/m 3 1,000 \text{ kg/m}^3 1 , 000 kg/m 3 62.428 lbm/ft 3 = 1.940 slugs/ft 3 62.428 \text{ lbm/ft}^3 = 1.940 \text{ slugs/ft}^3 62.428 lbm/ft 3 = 1.940 slugs/ft 3

Specific Weight of Water at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F γ water \gamma_{\text{water}} γ water ​ 9.790 kN/m 3 9.790 \text{ kN/m}^3 9.790 kN/m 3 62.37 lbf/ft 3 = 8.34 lbm/gal 62.37 \text{ lbf/ft}^3 = 8.34 \text{ lbm/gal} 62.37 lbf/ft 3 = 8.34 lbm/gal

Specific Heat of Liquid Water c p c_p c p ​ 4.184 kJ/(kg ⋅ ∘ C) 4.184 \text{ kJ/(kg}\cdot^\circ\text{C)} 4.184 kJ/(kg ⋅ ∘ C) 1.000 BTU/(lbm ⋅ ∘ F) 1.000 \text{ BTU/(lbm}\cdot^\circ\text{F)} 1.000 BTU/(lbm ⋅ ∘ F)

4. Dimensional Analysis & The Buckingham Pi Theorem

Dimensional analysis allows engineers to group physical variables into dimensionless numbers, reducing experimental complexity and enabling fluid/thermal scale-model testing. +-----------------------------------------------------------------------------------------+

  • | BUCKINGHAM PI THEOREM WORKFLOW |
  • | |
  • | [STEP 1: Identify all n variables influencing the physical phenomenon] |
  • | [STEP 2: Express each variable in fundamental dimensions (M, L, T, Theta)] |
  • | [STEP 3: Determine k = number of independent fundamental dimensions involved] |
  • | [STEP 4: Calculate number of dimensionless Pi groups: Pi_count = n - k] |
  • | [STEP 5: Select k repeating variables (must contain all k dimensions)] |
  • | [STEP 6: Form equations for each Pi group and solve exponents to ensure dimensionless] |
  • +-----------------------------------------------------------------------------------------+
  • Primary Dimensionless Parameters in Mechanical Engineering

Parameter Formula Physical Interpretation Key Applications

Reynolds Number ( R e Re R e ) ρ v D μ = v D ν \frac{\rho v D}{\mu} = \frac{v D}{\nu} μ ρ v D ​ = ν v D ​ Inertial Forces Viscous Forces \frac{\text{Inertial Forces}}{\text{Viscous Forces}} Viscous Forces Inertial Forces ​ Pipe flow, aerodynamics, boundary layer transition

Mach Number ( M a Ma M a ) v c = v k R T \frac{v}{c} = \frac{v}{\sqrt{k R T}} c v ​ = k RT ​ v ​ Flow Velocity Speed of Sound \frac{\text{Flow Velocity}}{\text{Speed of Sound}} Speed of Sound Flow Velocity ​ Compressible flow, nozzle design, gas dynamics

Prandtl Number ( P r Pr P r ) ν α = μ c p k \frac{\nu}{\alpha} = \frac{\mu c_p}{k} α ν ​ = k μ c p ​ ​ Momentum Diffusivity Thermal Diffusivity \frac{\text{Momentum Diffusivity}}{\text{Thermal Diffusivity}} Thermal Diffusivity Momentum Diffusivity ​ Convection boundary layer analysis

Nusselt Number ( N u Nu N u ) h L k fluid \frac{h L}{k_{\text{fluid}}} k fluid ​ h L ​ Convective Heat Transfer Pure Fluid Conduction \frac{\text{Convective Heat Transfer}}{\text{Pure Fluid Conduction}} Pure Fluid Conduction Convective Heat Transfer ​ Convective heat transfer coefficient sizing

Biot Number ( B i Bi B i ) h L c k solid \frac{h L_c}{k_{\text{solid}}} k solid ​ h L c ​ ​ Internal Conductive Resistance External Convective Resistance \frac{\text{Internal Conductive Resistance}}{\text{External Convective Resistance}} External Convective Resistance Internal Conductive Resistance ​ Lumped capacitance validity ( B i < 0.1 Bi < 0.1 B i < 0.1 )

Fourier Number ( F o Fo F o ) α t L c 2 \frac{\alpha t}{L_c^2} L c 2 ​ α t ​ Dimensionless Time Thermal Storage Rate \frac{\text{Dimensionless Time}}{\text{Thermal Storage Rate}} Thermal Storage Rate Dimensionless Time ​ Transient conduction cooling/heating

Euler Number ( E u Eu E u ) Δ P ρ v 2 \frac{\Delta P}{\rho v^2} ρ v 2 Δ P ​ Pressure Forces Inertial Forces \frac{\text{Pressure Forces}}{\text{Inertial Forces}} Inertial Forces Pressure Forces ​ Fluid machinery, cavitation, pipe friction

5. Step-by-Step Worked Problem: Fan Air Power in Dual Units

Problem: A ventilation fan delivers Q = 8 , 500 CFM Q = 8,500 \text{ CFM} Q = 8 , 500 CFM ( 14 , 441 m 3 / h 14,441 \text{ m}^3/\text{h} 14 , 441 m 3 / h ) of standard air against a total static pressure resistance of Δ P = 2.75 in. w.g. \Delta P = 2.75 \text{ in. w.g.} Δ P = 2.75 in. w.g. ( 685 Pa 685 \text{ Pa} 685 Pa ). The total fan efficiency is η t = 68 % \eta_t = 68\% η t ​ = 68% .

Calculate the required fan shaft brake horsepower (BHP) and shaft power in kilowatts (kW). +-----------------------------------------------------------------------------------------+

  • | FAN POWER STEP-BY-STEP CALCULATION |
  • | |
  • | METHOD 1: US CUSTOMARY CALCULATION |
  • | Static Air Power Formula: |
  • | Air HP = (Q [CFM] * Delta P [in. w.g.]) / 6,356 |
  • | |
  • | Derivation of Constant 6,356: |
  • | 1 in. w.g. = 5.204 lbf/ft^2 |
  • | Power = (Q [ft^3/min] * 5.204 [lbf/ft^2]) = 5.204 * Q ft*lbf/min |
  • | 1 HP = 33,000 ft*lbf/min |
  • | Air HP = (5.204 / 33,000) * Q * Delta P = (Q * Delta P) / 6,341.27 (at standard rho) |
  • | (Standard HVAC engineering uses 6,356 for air at 70 deg F, 29.92 in. Hg). |
  • | |
  • | Air HP = (8,500 * 2.75) / 6,356 = 23,375 / 6,356 = 3.6776 Air HP |
  • | Brake Horsepower (BHP) = Air HP / eta_t = 3.6776 / 0.68 = 5.408 BHP |
  • | |
  • | METHOD 2: SI CALCULATION |
  • | Q = 8,500 ft^3/min * (0.0283168 m^3/ft^3) * (1 min / 60 s) = 4.0115 m^3/s |
  • | Delta P = 2.75 in. w.g. * (249.08 Pa / 1 in. w.g.) = 684.97 Pa (N/m^2) |
  • | Air Power = Q * Delta P = (4.0115 m^3/s) * (684.97 N/m^2) = 2,747.76 W = 2.748 kW |
  • | Shaft Power = Air Power / eta_t = 2.74776 kW / 0.68 = 4.041 kW |
  • | |
  • | CROSS-CHECK CONVERSION: |
  • | 4.041 kW * (1 hp / 0.7457 kW) = 5.419 BHP (Exact match within rounding). |
  • +-----------------------------------------------------------------------------------------+