Study guide

2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses

Key Takeaways Explain This Topic AI

Fatigue is the primary cause of mechanical component failure in service, progressing through micro-crack initiation at stress risers, subcritical propagation (leaving visible beach marks), and sudden catastrophic fast fracture at stresses far below static yield.

The baseline uncorrected rotary-beam endurance limit for steel is estimated as S e ′ = 0.50 S u t S_e' = 0.50 S_{ut} S e ′ ​ = 0.50 S u t ​ (for S u t ≤ 200 kpsi S_{ut} \le 200\text{ kpsi} S u t ​ ≤ 200 kpsi or 1400 MPa 1400\text{ MPa} 1400 MPa ), which must be adjusted for actual operating conditions via the Marin equation: S e = k a k b k c k d k e k f S e ′ S_e = k_a k_b k_c k_d k_e k_f S_e' S e ​ = k a ​ k b ​ k c ​ k d ​ k e ​ k f ​ S e ′ ​ .

Geometric stress concentrations under cyclic loading are converted to fatigue stress concentration factors using material notch sensitivity: K f = 1 + q ( K t − 1 ) K_f = 1 + q(K_t - 1) K f ​ = 1 + q ( K t ​ − 1 ) , where 0 ≤ q ≤ 1 0 \le q \le 1 0 ≤ q ≤ 1 .

Fluctuating multiaxial stresses are resolved into alternating stress σ a \sigma_a σ a ​ and mean stress σ m \sigma_m σ m ​ ; design boundaries are evaluated using the Modified Goodman, Soderberg, Gerber, and ASME Elliptic criteria, and must always be cross-checked against first-cycle yielding via the Langer line ( n y = S y / ( σ a + σ m ) n_y = S_y / (\sigma_a + \sigma_m) n y ​ = S y ​ / ( σ a ​ + σ m ​ ) ).

Cumulative fatigue damage under variable-amplitude spectrum loading is evaluated using the Palmgren-Miner linear damage rule: ∑ i = 1 k n i N i = 1.0 \sum_{i=1}^k \frac{n_i}{N_i} = 1.0 ∑ i = 1 k ​ N i ​ n i ​ ​ = 1.0 .

Last updated: August 2026

Fatigue Analysis, S-N Curves & Fluctuating Stresses

Upwards of 90% of all mechanical failures in rotating machinery, ground vehicles, turbomachinery, and pressure systems are caused by fatigue —failure under repetitive, fluctuating, or reversed cyclic stresses. Fatigue occurs at stress amplitudes substantially lower than the static tensile yield strength ( S y S_y S y ​ ) with little or no macroscopic warning.

1. Fatigue Mechanisms & High-Cycle vs. Low-Cycle Regimes +-----------------------------------------------------------------------------+

  • | STAGES OF FATIGUE FAILURE |
  • | |
  • | Stage I: Micro-crack initiation at persistent slip bands, grain |
  • | boundaries, inclusions, or geometric notches. |
  • | |
  • | Stage II: Transgranular crack propagation perpendicular to maximum |
  • | tensile stress; leaves microscopic striations and macroscopic |
  • | clamshell / beach marks. |
  • | |
  • | Stage III: Sudden fast fracture when the remaining uncracked ligament |
  • | exceeds the plane strain fracture toughness (K_I \ge K_{Ic}). |
  • +-----------------------------------------------------------------------------+

Low-Cycle Fatigue (LCF, N < 10 3 N < 10^3 N < 1 0 3 to 10 4 10^4 1 0 4 cycles): Associated with significant cyclic plastic strains (e.g. thermal cycling of turbine casings). Governed by the Manson-Coffin strain-life relationship ( Δ ϵ p / 2 = ϵ f ′ ( 2 N ) c \Delta \epsilon_p / 2 = \epsilon_f' (2N)^c Δ ϵ p ​ /2 = ϵ f ′ ​ ( 2 N ) c ).

High-Cycle Fatigue (HCF, N > 10 3 N > 10^3 N > 1 0 3 to 10 4 10^4 1 0 4 cycles): Macroscopic strains remain purely elastic. Governed by stress-life ( S - N S\text{-}N S - N ) methods.

2. S-N Diagrams & Uncorrected Endurance Limit

In standard laboratory R.R. Moore rotating-beam testing (pure reversed bending, polished specimen, room temperature), ferrous alloys display a true endurance limit ( S e ′ S_e' S e ′ ​ ) below which the material can endure an infinite number of cycles ( N > 10 6 N > 10^6 N > 1 0 6 ) without failing. Stress Amplitude S_f

  • ^
  • | (f * S_ut) at 10^3 cycles
  • | \
  • | \ Finite Life Region (S_f = a * N^b)
  • | \
  • | \-------------------- Endurance Limit S_e' (Infinite Life)
  • | \
  • +---------+-------------------+-----------------------------> Cycles N
  • 10^3 10^6

Uncorrected Endurance Limit for Steels ( S e ′ S_e' S e ′ ​ ): S e ′ = { 0.50 S u t for S u t ≤ 200 kpsi ( 1400 MPa ) 100 kpsi ( 700 MPa ) for S u t > 200 kpsi ( 1400 MPa ) S_e' = \begin{cases} 0.50 S_{ut} & \text{for } S_{ut} \le 200\text{ kpsi } (1400\text{ MPa}) \\ 100\text{ kpsi } (700\text{ MPa}) & \text{for } S_{ut} > 200\text{ kpsi } (1400\text{ MPa}) \end{cases} S e ′ ​ = { 0.50 S u t ​ 100 kpsi ( 700 MPa ) ​ for S u t ​ ≤ 200 kpsi ( 1400 MPa ) for S u t ​ > 200 kpsi ( 1400 MPa ) ​

Finite Life Equation ( 10 3 ≤ N ≤ 10 6 10^3 \le N \le 10^6 1 0 3 ≤ N ≤ 1 0 6 cycles): S f = a N b S_f = a N^b S f ​ = a N b b = − 1 3 log ⁡ 10 ( f S u t S e ) , a = ( f S u t ) 2 S e b = -\frac{1}{3} \log_{10}\left(\frac{f S_{ut}}{S_e}\right), \quad a = \frac{(f S_{ut})^2}{S_e} b = − 3 1 ​ lo g 10 ​ ( S e ​ f S u t ​ ​ ) , a = S e ​ ( f S u t ​ ) 2 ​

Where f f f is the fatigue strength fraction at 10 3 10^3 1 0 3 cycles (typically f ≈ 0.90 f \approx 0.90 f ≈ 0.90 for S u t ≤ 70 kpsi S_{ut} \le 70\text{ kpsi} S u t ​ ≤ 70 kpsi down to f ≈ 0.80 f \approx 0.80 f ≈ 0.80 for S u t ≥ 200 kpsi S_{ut} \ge 200\text{ kpsi} S u t ​ ≥ 200 kpsi ).

3. Marin Modifying Factors for Real-World Components

The laboratory endurance limit S e ′ S_e' S e ′ ​ must be reduced using Marin modifying factors to account for surface finish, component size, loading mode, operating temperature, target reliability, and environmental effects: S e = k a k b k c k d k e k f S e ′ S_e = k_a k_b k_c k_d k_e k_f S_e' S e ​ = k a ​ k b ​ k c ​ k d ​ k e ​ k f ​ S e ′ ​ +-----------------------------------------------------------------------------+

  • | MARIN FACTOR REFERENCE |
  • | |
  • | 1. Surface Factor: k_a = a S_{ut}^b |
  • | - Ground: a = 1.58 MPa, b = -0.085 (a = 1.34 kpsi) |
  • | - Machined/Cold-Drawn: a = 4.51 MPa, b = -0.265 (a = 2.70 kpsi) |
  • | - Hot-Rolled: a = 57.7 MPa, b = -0.718 (a = 14.4 kpsi) |
  • | - As-Forged: a = 272 MPa, b = -0.995 (a = 39.9 kpsi) |
  • | |
  • | 2. Size Factor (Bending/Torsion): |
  • | - 2.79 mm \le d \le 51 mm: k_b = 1.24 d^{-0.107} |
  • | - 51 mm < d \le 254 mm: k_b = 1.51 d^{-0.157} |
  • | - Axial Loading: k_b = 1.0 (size accounted for in k_c) |
  • | |
  • | 3. Load Factor: |
  • | - Bending: k_c = 1.0 |
  • | - Axial: k_c = 0.85 |
  • | - Torsion / Shear: k_c = 0.59 |
  • | |
  • | 4. Temperature Factor: k_d = S_T / S_{RT} |
  • | |
  • | 5. Reliability Factor: |
  • | - 50%: k_e = 1.000 | 90%: k_e = 0.897 | 99%: k_e = 0.814 | 99.9%: 0.753|
  • +-----------------------------------------------------------------------------+

Fatigue Stress Concentration Factor ( K f K_f K f ​ ): K f = 1 + q ( K t − 1 ) K_f = 1 + q (K_t - 1) K f ​ = 1 + q ( K t ​ − 1 )

Where notch sensitivity q = 1 1 + a r q = \frac{1}{1 + \frac{\sqrt{a}}{\sqrt{r}}} q = 1 + r ​ a ​ ​ 1 ​ (Neuber equation, with material constant a \sqrt{a} a ​ and notch radius r r r ).

4. Fluctuating Multiaxial Stresses & Mean Stress Failure Criteria

A general fluctuating stress cycle varies between σ max \sigma_{\text{max}} σ max ​ and σ min \sigma_{\text{min}} σ min ​ :

Alternating Stress: σ a = ∣ σ max − σ min ∣ 2 \sigma_a = \frac{|\sigma_{\text{max}} - \sigma_{\text{min}}|}{2} σ a ​ = 2 ∣ σ max ​ − σ min ​ ∣ ​

Mean Stress: σ m = σ max + σ min 2 \sigma_m = \frac{\sigma_{\text{max}} + \sigma_{\text{min}}}{2} σ m ​ = 2 σ max ​ + σ min ​ ​

Stress Ratio: R = σ min σ max R = \frac{\sigma_{\text{min}}}{\sigma_{\text{max}}} R = σ max ​ σ min ​ ​ Alternating Stress \sigma_a

  • ^
  • |
  • Endurance * (Soderberg Line)
  • Limit |\
  • S_e ----+-\---* (Modified Goodman Line)
  • | \ \
  • | \ \---* (Gerber Parabola)
  • | \ \ \
  • +-----+---+---+-----> Mean Stress \sigma_m
  • S_y S_{ut}
  • Classical Mean Stress Criteria Formulation

Criterion Governing Equation Application / Characteristics

Modified Goodman σ a S e + σ m S u t = 1 n f \frac{\sigma_a}{S_e} + \frac{\sigma_m}{S_{ut}} = \frac{1}{n_f} S e ​ σ a ​ ​ + S u t ​ σ m ​ ​ = n f ​ 1 ​ Standard engineering practice; conservative and safe for ductile metals.

Soderberg σ a S e + σ m S y = 1 n f \frac{\sigma_a}{S_e} + \frac{\sigma_m}{S_y} = \frac{1}{n_f} S e ​ σ a ​ ​ + S y ​ σ m ​ ​ = n f ​ 1 ​ Most conservative; guards against first-cycle yielding automatically.

Gerber Parabola n f σ a S e + ( n f σ m S u t ) 2 = 1 \frac{n_f \sigma_a}{S_e} + \left(\frac{n_f \sigma_m}{S_{ut}}\right)^2 = 1 S e ​ n f ​ σ a ​ ​ + ( S u t ​ n f ​ σ m ​ ​ ) 2 = 1 Best parabolic fit to mean experimental data for ductile metals.

ASME Elliptic ( n f σ a S e ) 2 + ( n f σ m S y ) 2 = 1 \left(\frac{n_f \sigma_a}{S_e}\right)^2 + \left(\frac{n_f \sigma_m}{S_y}\right)^2 = 1 ( S e ​ n f ​ σ a ​ ​ ) 2 + ( S y ​ n f ​ σ m ​ ​ ) 2 = 1 Smooth elliptical boundary connecting S e S_e S e ​ on σ a \sigma_a σ a ​ and S y S_y S y ​ on σ m \sigma_m σ m ​ .

First-Cycle Static Yield Check (Langer Static Yield Line)

Regardless of which fatigue criterion is used, the component must be verified against gross yielding during startup transients: n y = S y σ a + σ m = S y σ max n_y = \frac{S_y}{\sigma_a + \sigma_m} = \frac{S_y}{\sigma_{\text{max}}} n y ​ = σ a ​ + σ m ​ S y ​ ​ = σ max ​ S y ​ ​

Combined Multiaxial Fluctuating Stresses (von Mises): σ a ′ = σ x a 2 − σ x a σ y a + σ y a 2 + 3 τ x y a 2 \sigma_a' = \sqrt{\sigma_{xa}^2 - \sigma_{xa}\sigma_{ya} + \sigma_{ya}^2 + 3\tau_{xya}^2} σ a ′ ​ = σ x a 2 ​ − σ x a ​ σ y a ​ + σ y a 2 ​ + 3 τ x y a 2 ​ ​ σ m ′ = σ x m 2 − σ x m σ y m + σ y m 2 + 3 τ x y m 2 \sigma_m' = \sqrt{\sigma_{xm}^2 - \sigma_{xm}\sigma_{ym} + \sigma_{ym}^2 + 3\tau_{xym}^2} σ m ′ ​ = σ x m 2 ​ − σ x m ​ σ y m ​ + σ y m 2 ​ + 3 τ x y m 2 ​ ​

(Note: When evaluating multiaxial fatigue with von Mises effective stresses, set the Marin load factor k c = 1.0 k_c = 1.0 k c ​ = 1.0 , as the 3 \sqrt{3} 3 ​ factor already incorporates shear behavior).

5. Cumulative Fatigue Damage & Palmgren-Miner's Rule

When a mechanical component is subjected to variable-amplitude multi-block loading spectra, cumulative damage is quantified using the Palmgren-Miner Linear Damage Hypothesis : D = ∑ i = 1 k n i N i = n 1 N 1 + n 2 N 2 + ⋯ + n k N k = 1.0 D = \sum_{i=1}^k \frac{n_i}{N_i} = \frac{n_1}{N_1} + \frac{n_2}{N_2} + \cdots + \frac{n_k}{N_k} = 1.0 D = i = 1 ∑ k ​ N i ​ n i ​ ​ = N 1 ​ n 1 ​ ​ + N 2 ​ n 2 ​ ​ + ⋯ + N k ​ n k ​ ​ = 1.0

Where n i n_i n i ​ is the number of applied cycles at stress level σ i \sigma_i σ i ​ , and N i N_i N i ​ is the fatigue life (cycles to failure) at that same stress level from the component's S - N S\text{-}N S - N curve.

  • 6. Step-by-Step Worked Engineering Problem
  • Problem Statement

A solid transmission shaft made of cold-drawn steel ( S u t = 650 MPa , S y = 530 MPa S_{ut} = 650\text{ MPa}, S_y = 530\text{ MPa} S u t ​ = 650 MPa , S y ​ = 530 MPa ) with diameter d = 35 mm d = 35\text{ mm} d = 35 mm operates at 20 ∘ C 20^\circ\text{C} 2 0 ∘ C with 99% reliability. It contains a shoulder fillet with K t = 1.70 K_t = 1.70 K t ​ = 1.70 and notch sensitivity q = 0.85 q = 0.85 q = 0.85 . The shaft is subjected to a completely reversed bending moment M a = 320 N ⋅ m M_a = 320\text{ N}\cdot\text{m} M a ​ = 320 N ⋅ m and a steady torsional torque T m = 450 N ⋅ m T_m = 450\text{ N}\cdot\text{m} T m ​ = 450 N ⋅ m .

Determine: (a) fully corrected endurance limit S e S_e S e ​ , (b) fatigue factor of safety n f n_f n f ​ using Modified Goodman, and (c) static yield factor of safety n y n_y n y ​ .

Step 1: Baseline Endurance Limit & Marin Factors S e ′ = 0.50 S u t = 0.50 ( 650 ) = 325 MPa S_e' = 0.50 S_{ut} = 0.50(650) = 325\text{ MPa} S e ′ ​ = 0.50 S u t ​ = 0.50 ( 650 ) = 325 MPa

Surface Factor ( k a k_a k a ​ , Cold-Drawn): k a = 4.51 ( 650 ) − 0.265 = 4.51 ( 0.1798 ) = 0.811 k_a = 4.51 (650)^{-0.265} = 4.51 (0.1798) = 0.811 k a ​ = 4.51 ( 650 ) − 0.265 = 4.51 ( 0.1798 ) = 0.811

Size Factor ( k b k_b k b ​ , Bending, d = 35 mm d = 35\text{ mm} d = 35 mm ): k b = 1.24 ( 35 ) − 0.107 = 1.24 ( 0.6833 ) = 0.847 k_b = 1.24 (35)^{-0.107} = 1.24 (0.6833) = 0.847 k b ​ = 1.24 ( 35 ) − 0.107 = 1.24 ( 0.6833 ) = 0.847

  • Load Factor ( k c k_c k c ​ ): k c = 1.0 k_c = 1.0 k c ​ = 1.0 (bending/von Mises)
  • Temperature Factor ( k d k_d k d ​ ): k d = 1.0 k_d = 1.0 k d ​ = 1.0
  • Reliability Factor ( k e k_e k e ​ , 99%): k e = 0.814 k_e = 0.814 k e ​ = 0.814

Corrected Endurance Limit: S e = ( 0.811 ) ( 0.847 ) ( 1.0 ) ( 1.0 ) ( 0.814 ) ( 325 ) = 181.7 MPa S_e = (0.811)(0.847)(1.0)(1.0)(0.814)(325) = 181.7\text{ MPa} S e ​ = ( 0.811 ) ( 0.847 ) ( 1.0 ) ( 1.0 ) ( 0.814 ) ( 325 ) = 181.7 MPa

Step 2: Fatigue Stress Concentration Factor ( K f K_f K f ​ ) K f = 1 + q ( K t − 1 ) = 1 + 0.85 ( 1.70 − 1 ) = 1 + 0.85 ( 0.70 ) = 1.595 K_f = 1 + q (K_t - 1) = 1 + 0.85(1.70 - 1) = 1 + 0.85(0.70) = 1.595 K f ​ = 1 + q ( K t ​ − 1 ) = 1 + 0.85 ( 1.70 − 1 ) = 1 + 0.85 ( 0.70 ) = 1.595

Step 3: Nominal and Peak Alternating / Mean Stresses

Alternating Bending Stress (Reversed, M m = 0 M_m = 0 M m ​ = 0 ): σ a = K f 32 M a π d 3 = 1.595 32 ( 320 ) π ( 0.035 ) 3 = 1.595 10240 1.347 × 10 − 4 = 121.26 MPa \sigma_{a} = K_f \frac{32 M_a}{\pi d^3} = 1.595 \frac{32(320)}{\pi (0.035)^3} = 1.595 \frac{10240}{1.347 \times 10^{-4}} = 121.26\text{ MPa} σ a ​ = K f ​ π d 3 32 M a ​ ​ = 1.595 π ( 0.035 ) 3 32 ( 320 ) ​ = 1.595 1.347 × 1 0 − 4 10240 ​ = 121.26 MPa

Mean Torsional Shear Stress (Steady, T a = 0 T_a = 0 T a ​ = 0 ): τ m = 16 T m π d 3 = 16 ( 450 ) π ( 0.035 ) 3 = 53.45 MPa \tau_m = \frac{16 T_m}{\pi d^3} = \frac{16(450)}{\pi (0.035)^3} = 53.45\text{ MPa} τ m ​ = π d 3 16 T m ​ ​ = π ( 0.035 ) 3 16 ( 450 ) ​ = 53.45 MPa

Step 4: von Mises Alternating and Mean Stresses σ a ′ = σ a 2 + 3 ( 0 ) 2 = σ a = 121.26 MPa \sigma_a' = \sqrt{\sigma_a^2 + 3(0)^2} = \sigma_a = 121.26\text{ MPa} σ a ′ ​ = σ a 2 ​ + 3 ( 0 ) 2 ​ = σ a ​ = 121.26 MPa σ m ′ = ( 0 ) 2 + 3 τ m 2 = 3 ( 53.45 ) = 92.58 MPa \sigma_m' = \sqrt{(0)^2 + 3\tau_m^2} = \sqrt{3}(53.45) = 92.58\text{ MPa} σ m ′ ​ = ( 0 ) 2 + 3 τ m 2 ​ ​ = 3 ​ ( 53.45 ) = 92.58 MPa

Step 5: Safety Factors

Modified Goodman Fatigue Safety Factor ( n f n_f n f ​ ): 1 n f = σ a ′ S e + σ m ′ S u t = 121.26 181.7 + 92.58 650 = 0.6674 + 0.1424 = 0.8098 ⟹ n f = 1.23 \frac{1}{n_f} = \frac{\sigma_a'}{S_e} + \frac{\sigma_m'}{S_{ut}} = \frac{121.26}{181.7} + \frac{92.58}{650} = 0.6674 + 0.1424 = 0.8098 \implies n_f = 1.23 n f ​ 1 ​ = S e ​ σ a ′ ​ ​ + S u t ​ σ m ′ ​ ​ = 181.7 121.26 ​ + 650 92.58 ​ = 0.6674 + 0.1424 = 0.8098 ⟹ n f ​ = 1.23

First-Cycle Static Yield Safety Factor ( n y n_y n y ​ ): n y = S y σ a ′ + σ m ′ = 530 121.26 + 92.58 = 530 213.84 = 2.48 n_y = \frac{S_y}{\sigma_a' + \sigma_m'} = \frac{530}{121.26 + 92.58} = \frac{530}{213.84} = 2.48 n y ​ = σ a ′ ​ + σ m ′ ​ S y ​ ​ = 121.26 + 92.58 530 ​ = 213.84 530 ​ = 2.48

7. Common Exam Traps & PE Pro-Tips

Trap 1 — Double-Counting Shear Factor: When using the von Mises effective stress formulation for multiaxial fatigue, set Marin load factor k c = 1.0 k_c = 1.0 k c ​ = 1.0 . Do not multiply by 0.59 0.59 0.59 , as 3 τ m \sqrt{3}\tau_m 3 ​ τ m ​ already performs the distortion energy conversion.

Trap 2 — Neglecting First-Cycle Yielding: High mean stresses can cause catastrophic plastic deformation on the very first load cycle even when fatigue safety factor n f > 1.0 n_f > 1.0 n f ​ > 1.0 . Always check the Langer static line.

Trap 3 — Using K t K_t K t ​ instead of K f K_f K f ​ : Always calculate K f = 1 + q ( K t − 1 ) K_f = 1 + q(K_t - 1) K f ​ = 1 + q ( K t ​ − 1 ) . Using K t K_t K t ​ directly unnecessarily over-designs the component.