Study guide

5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry

Key Takeaways Explain This Topic AI

Atmospheric air is modeled as 21% O 2 \text{O}_2 O 2 ​ and 79% N 2 \text{N}_2 N 2 ​ by mole, establishing a standard molar ratio of 3.76 kmol N 2 / kmol O 2 3.76\text{ kmol }\text{N}_2 / \text{kmol }\text{O}_2 3.76 kmol N 2 ​ / kmol O 2 ​ with an average molecular weight of 28.97 kg/kmol 28.97\text{ kg/kmol} 28.97 kg/kmol .

The Equivalence Ratio ϕ = ( A / F ) s t o i c h / ( A / F ) a c t u a l \phi = (A/F)_{stoich} / (A/F)_{actual} ϕ = ( A / F ) s t o i c h ​ / ( A / F ) a c t u a l ​ classifies combustion mixtures as fuel-lean ( ϕ < 1 \phi < 1 ϕ < 1 ), stoichiometric ( ϕ = 1 \phi = 1 ϕ = 1 ), or fuel-rich ( ϕ > 1 \phi > 1 ϕ > 1 ).

Orsat gas analyzers measure combustion exhaust on a dry basis; converting to a wet basis requires accounting for condensed water vapor: y i , w e t = y i , d r y ( 1 − y H 2 O , w e t ) y_{i,wet} = y_{i,dry}(1 - y_{\text{H}_2\text{O},wet}) y i , w e t ​ = y i , d ry ​ ( 1 − y H 2 ​ O , w e t ​ ) .

The Higher Heating Value (HHV) includes the latent heat of condensation of water formed during combustion, whereas the Lower Heating Value (LHV) assumes water remains in the vapor phase.

Adiabatic flame temperature represents the theoretical upper temperature limit of combustion, reached when no heat is lost to surroundings and no work is performed.

Last updated: August 2026

Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry

Combustion is a rapid chemical reaction in which fuel oxidizes, releasing stored chemical bond energy as high-temperature thermal energy. On the NCEES PE Mechanical exam, combustion questions test stoichiometric balancing, theoretical and excess air requirements, mass-based Air-Fuel ( A F AF A F ) ratios, Orsat flue gas interpretations, heating values ( H H V HHV HH V vs L H V LHV L H V ), and adiabatic flame temperatures.

1. Fuel Classes & Atmospheric Air Composition

Power generation fuels encompass diverse physical forms and chemical compositions: +-----------------------------------------------------------------------------------------+

  • | COMMON ENGINEERING FUEL TYPES |
  • | |
  • | GASEOUS FUELS: Methane (CH4, natural gas ~90-95%), Propane (C3H8), Butane (C4H10) |
  • | LIQUID FUELS: Gasoline (model: Octane C8H18), Diesel/Fuel Oil (model: C12H23) |
  • | SOLID FUELS: Coal (Anthracite, Bituminous, Lignite), Biomass, Refuse-Derived |
  • +-----------------------------------------------------------------------------------------+
  • Atmospheric Combustion Air

Dry atmospheric air is composed of approximately 21 % O 2 21\% \text{ O}_2 21% O 2 ​ and 79 % N 2 79\% \text{ N}_2 79% N 2 ​ by volume (molar basis). For every mole of oxygen involved in combustion, there are: 0.79 kmol N 2 0.21 kmol O 2 = 3.76 kmol N 2 kmol O 2 \frac{0.79 \text{ kmol } \text{N}_2}{0.21 \text{ kmol } \text{O}_2} = 3.76 \frac{\text{kmol } \text{N}_2}{\text{kmol } \text{O}_2} 0.21 kmol O 2 ​ 0.79 kmol N 2 ​ ​ = 3.76 kmol O 2 ​ kmol N 2 ​ ​ M a i r = 0.21 ( 32.00 ) + 0.79 ( 28.013 ) = 28.97 kg/kmol ≈ 28.97 lbm/lbmol M_{air} = 0.21(32.00) + 0.79(28.013) = 28.97 \text{ kg/kmol} \approx 28.97 \text{ lbm/lbmol} M ai r ​ = 0.21 ( 32.00 ) + 0.79 ( 28.013 ) = 28.97 kg/kmol ≈ 28.97 lbm/lbmol

Nitrogen is assumed to act as an inert diatomic spectator gas in standard stoichiometric calculations, absorbing heat without reacting directly.

2. Stoichiometric Balancing & Excess Air Calculations

Stoichiometric (Theoretical) Air is the exact minimum quantity of oxygen required to completely oxidize all carbon to carbon dioxide ( CO 2 \text{CO}_2 CO 2 ​ ), all hydrogen to water ( H 2 O \text{H}_2\text{O} H 2 ​ O ), and all sulfur to sulfur dioxide ( SO 2 \text{SO}_2 SO 2 ​ ), leaving zero unburned fuel and zero free oxygen in the exhaust products. +-----------------------------------------------------------------------------------------+

  • | GENERAL STOICHIOMETRIC HYDROCARBON BALANCING |
  • | |
  • | For a generic hydrocarbon C_n H_m: |
  • | |
  • | C_n H_m + a_th (O_2 + 3.76 N_2) ---> n CO_2 + (m/2) H_2O + 3.76 a_th N_2 |
  • | |
  • | Balancing Oxygen: a_th = n + m/4 |
  • | |
  • | For an oxygenated fuel C_n H_m O_p: |
  • | a_th = n + m/4 - p/2 |
  • +-----------------------------------------------------------------------------------------+
  • Excess Air & Equivalence Ratio

Industrial boilers and gas turbines always operate with Excess Air to ensure complete combustion, avoid deadly carbon monoxide ( CO \text{CO} CO ) and soot formation, and moderate peak flame temperatures: Percent Excess Air = m ˙ a i r , a c t u a l − m ˙ a i r , s t o i c h m ˙ a i r , s t o i c h × 100 = ( Percent Theoretical Air ) − 100 \text{Percent Excess Air} = \frac{\dot{m}_{air,actual} - \dot{m}_{air,stoich}}{\dot{m}_{air,stoich}} \times 100 = (\text{Percent Theoretical Air}) - 100 Percent Excess Air = m ˙ ai r , s t o i c h ​ m ˙ ai r , a c t u a l ​ − m ˙ ai r , s t o i c h ​ ​ × 100 = ( Percent Theoretical Air ) − 100 Actual Moles of Air a a c t = ( 1 + Percent Excess Air 100 ) a t h \text{Actual Moles of Air } a_{act} = \left(1 + \frac{\text{Percent Excess Air}}{100}\right) a_{th} Actual Moles of Air a a c t ​ = ( 1 + 100 Percent Excess Air ​ ) a t h ​

The Equivalence Ratio ( ϕ \phi ϕ ) relates the actual fuel-to-air ratio to the stoichiometric ratio: ϕ = ( F / A ) a c t u a l ( F / A ) s t o i c h = ( A / F ) s t o i c h ( A / F ) a c t u a l \phi = \frac{(F/A)_{actual}}{(F/A)_{stoich}} = \frac{(A/F)_{stoich}}{(A/F)_{actual}} ϕ = ( F / A ) s t o i c h ​ ( F / A ) a c t u a l ​ ​ = ( A / F ) a c t u a l ​ ( A / F ) s t o i c h ​ ​

ϕ = 1.0 \phi = 1.0 ϕ = 1.0 : Stoichiometric mixture

ϕ < 1.0 \phi < 1.0 ϕ < 1.0 : Fuel-lean (excess air, common in boilers ∼ 10 − 25 % \sim 10-25\% ∼ 10 − 25% and gas turbines ∼ 100 − 300 % \sim 100-300\% ∼ 100 − 300% )

ϕ > 1.0 \phi > 1.0 ϕ > 1.0 : Fuel-rich (excess fuel, incomplete combustion, generates CO \text{CO} CO and H 2 \text{H}_2 H 2 ​ )

Air-Fuel ( A F AF A F ) Ratio Formulations ( A / F ) m o l a r = N a i r N f u e l = a a c t ( 1 + 3.76 ) 1.0 = 4.76 ⋅ a a c t (A/F)_{molar} = \frac{N_{air}}{N_{fuel}} = \frac{a_{act} (1 + 3.76)}{1.0} = 4.76 \cdot a_{act} ( A / F ) m o l a r ​ = N f u e l ​ N ai r ​ ​ = 1.0 a a c t ​ ( 1 + 3.76 ) ​ = 4.76 ⋅ a a c t ​ ( A / F ) m a s s = m a i r m f u e l = N a i r ⋅ M a i r N f u e l ⋅ M f u e l = 4.76 ⋅ a a c t ⋅ 28.97 M f u e l (A/F)_{mass} = \frac{m_{air}}{m_{fuel}} = \frac{N_{air} \cdot M_{air}}{N_{fuel} \cdot M_{fuel}} = \frac{4.76 \cdot a_{act} \cdot 28.97}{M_{fuel}} ( A / F ) ma ss ​ = m f u e l ​ m ai r ​ ​ = N f u e l ​ ⋅ M f u e l ​ N ai r ​ ⋅ M ai r ​ ​ = M f u e l ​ 4.76 ⋅ a a c t ​ ⋅ 28.97 ​

3. Flue Gas Analysis (Orsat) & Flue Acid Dew Point

An Orsat Gas Analyzer measures the volumetric (molar) concentrations of combustion products on a dry basis , because water vapor is intentionally condensed and drained from the sample line before chemical absorption. +-----------------------------------------------------------------------------------------+

  • | DRY TO WET FLUE GAS CONVERSIONS |
  • | |
  • | Let the dry gas mole numbers be: N_dry = N_CO2 + N_CO + N_O2 + N_N2 |
  • | Total combustion products: N_total = N_dry + N_H2O |
  • | |
  • | Wet Molar Fraction: y_i,wet = N_i / N_total = y_i,dry * (1 - y_H2O,wet) |
  • | Water Vapor Fraction: y_H2O,wet = N_H2O / (N_dry + N_H2O) |
  • +-----------------------------------------------------------------------------------------+
  • Flue Gas Acid Dew Point Prevention

The partial pressure of water vapor in wet flue gas is: P v = y H 2 O , w e t ⋅ P t o t a l P_v = y_{\text{H}_2\text{O},wet} \cdot P_{total} P v ​ = y H 2 ​ O , w e t ​ ⋅ P t o t a l ​

The water dew point is the saturation temperature T s a t ( P v ) T_{sat}(P_v) T s a t ​ ( P v ​ ) . If exhaust gas cools below this temperature, liquid water condenses in the stack.

Warning

The Acid Condensation Trap: If the fuel contains sulfur ( S S S ), combustion forms sulfur dioxide ( SO 2 \text{SO}_2 SO 2 ​ ) and sulfur trioxide ( SO 3 \text{SO}_3 SO 3 ​ ). In the presence of water vapor, SO 3 \text{SO}_3 SO 3 ​ combines with H 2 O \text{H}_2\text{O} H 2 ​ O to form sulfuric acid ( H 2 SO 4 \text{H}_2\text{SO}_4 H 2 ​ SO 4 ​ ), which has an acid dew point of 120 ∘ C to 150 ∘ C 120^\circ\text{C} \text{ to } 150^\circ\text{C} 12 0 ∘ C to 15 0 ∘ C ( 250 ∘ F − 300 ∘ F 250^\circ\text{F} - 300^\circ\text{F} 25 0 ∘ F − 30 0 ∘ F ) . Flue gas stack temperatures must always be maintained safely above the acid dew point to prevent devastating corrosion of economizers, air preheaters, and breeching ductwork.

4. Thermochemistry: Enthalpy of Formation & Heating Values

For a steady-flow reactive system with zero work and negligible kinetic/potential energy changes, the First Law is expressed as: Q ˙ o u t = ∑ reactants N ˙ r ( h ˉ f ∘ + h ˉ − h ˉ ∘ ) r − ∑ products N ˙ p ( h ˉ f ∘ + h ˉ − h ˉ ∘ ) p \dot{Q}_{out} = \sum_{\text{reactants}} \dot{N}_r \left(\bar{h}_f^\circ + \bar{h} - \bar{h}^\circ\right)_r - \sum_{\text{products}} \dot{N}_p \left(\bar{h}_f^\circ + \bar{h} - \bar{h}^\circ\right)_p Q ˙ ​ o u t ​ = reactants ∑ ​ N ˙ r ​ ( h ˉ f ∘ ​ + h ˉ − h ˉ ∘ ) r ​ − products ∑ ​ N ˙ p ​ ( h ˉ f ∘ ​ + h ˉ − h ˉ ∘ ) p ​

Where:

h ˉ f ∘ \bar{h}_f^\circ h ˉ f ∘ ​ is the Standard Enthalpy of Formation at reference state ( 25 ∘ C / 298.15 K , 1 atm 25^\circ\text{C} / 298.15\text{ K}, 1\text{ atm} 2 5 ∘ C /298.15 K , 1 atm ). For stable elements ( O 2 , N 2 , H 2 , C g r a p h i t e \text{O}_2, \text{N}_2, \text{H}_2, \text{C}_{graphite} O 2 ​ , N 2 ​ , H 2 ​ , C g r a p hi t e ​ ), h ˉ f ∘ = 0 \bar{h}_f^\circ = 0 h ˉ f ∘ ​ = 0 .

( h ˉ − h ˉ ∘ ) (\bar{h} - \bar{h}^\circ) ( h ˉ − h ˉ ∘ ) accounts for sensible enthalpy differences between state temperature T T T and the 298.15 K 298.15\text{ K} 298.15 K reference. +-----------------------------------------------------------------------------------------+

  • | STANDARD ENTHALPIES OF FORMATION (298 K) |
  • | |
  • | Substance Formula Enthalpy of Formation (kJ/kmol) |
  • | -------------------- ---------- ------------------------------ |
  • | Carbon Dioxide (g) CO2 -393,520 |
  • | Carbon Monoxide (g) CO -110,530 |
  • | Water Vapor (g) H2O(g) -241,820 |
  • | Water Liquid (l) H2O(l) -285,830 |
  • | Methane (g) CH4 -74,850 |
  • | Propane (g) C3H8 -103,850 |
  • | n-Octane (l) C8H18(l) -249,950 |
  • +-----------------------------------------------------------------------------------------+
  • Higher Heating Value (HHV) vs Lower Heating Value (LHV)

The heat of combustion represents the enthalpy released when a fuel is completely burned at standard conditions: Higher Heating Value (HHV) Lower Heating Value (LHV)

  • +--------------------------------+ +--------------------------------+
  • | H2O in combustion products is | | H2O in combustion products is |
  • | fully condensed to LIQUID | | fully in VAPOR phase |
  • | (Releases latent heat h_fg) | | (Carries away latent heat) |

+--------------------------------+ +--------------------------------+ H H V = L H V + ( m H 2 O m f u e l ) h f g , H 2 O HHV = LHV + \left(\frac{m_{\text{H}_2\text{O}}}{m_{fuel}}\right) h_{fg,\text{H}_2\text{O}} HH V = L H V + ( m f u e l ​ m H 2 ​ O ​ ​ ) h f g , H 2 ​ O ​

Where h f g , H 2 O h_{fg,\text{H}_2\text{O}} h f g , H 2 ​ O ​ is the enthalpy of vaporization of water evaluated at the standard reference temperature of 25 ∘ C 25^\circ\text{C} 2 5 ∘ C ( 2442.3 kJ/kg = 1050 BTU/lbm = 44 , 010 kJ/kmol H 2 O 2442.3 \text{ kJ/kg} = 1050 \text{ BTU/lbm} = 44,010 \text{ kJ/kmol } \text{H}_2\text{O} 2442.3 kJ/kg = 1050 BTU/lbm = 44 , 010 kJ/kmol H 2 ​ O ).

5. Adiabatic Flame Temperature ( T a d T_{ad} T a d ​ )

The Adiabatic Flame Temperature is the maximum theoretical temperature achieved during combustion when zero heat is lost to the environment ( Q ˙ = 0 \dot{Q} = 0 Q ˙ ​ = 0 ), zero shaft work is produced ( W ˙ = 0 \dot{W} = 0 W ˙ = 0 ), and changes in kinetic and potential energy are negligible: H p r o d u c t s ( T a d ) = H r e a c t a n t s ( T i ) H_{products}(T_{ad}) = H_{reactants}(T_i) H p ro d u c t s ​ ( T a d ​ ) = H re a c t an t s ​ ( T i ​ ) ∑ products N p [ h ˉ f ∘ + h ˉ ( T a d ) − h ˉ ∘ ] p = ∑ reactants N r [ h ˉ f ∘ + h ˉ ( T i ) − h ˉ ∘ ] r \sum_{\text{products}} N_p \left[\bar{h}_f^\circ + \bar{h}(T_{ad}) - \bar{h}^\circ\right]_p = \sum_{\text{reactants}} N_r \left[\bar{h}_f^\circ + \bar{h}(T_i) - \bar{h}^\circ\right]_r products ∑ ​ N p ​ [ h ˉ f ∘ ​ + h ˉ ( T a d ​ ) − h ˉ ∘ ] p ​ = reactants ∑ ​ N r ​ [ h ˉ f ∘ ​ + h ˉ ( T i ​ ) − h ˉ ∘ ] r ​ +-----------------------------------------------------------------------------------------+

  • | FACTORS INFLUENCING ADIABATIC FLAME TEMPERATURE |
  • | |
  • | 1. EXCESS AIR: Peak T_ad occurs at stoichiometric conditions (phi = 1.0). Excess air |
  • | acts as thermal ballast (inert mass absorbing heat), drastically reducing T_ad. |
  • | |
  • | 2. AIR PREHEAT: Preheating combustion air in an air preheater (AH) directly increases |
  • | reactants enthalpy H_reactants, driving T_ad significantly higher. |
  • | |
  • | 3. HIGH-TEMP DISSOCIATION: Above ~1800 K, endothermic chemical dissociation |
  • | (CO2 <--> CO + 0.5 O2, H2O <--> H2 + 0.5 O2) absorbs heat, clamping maximum T_ad. |
  • +-----------------------------------------------------------------------------------------+
  • 6. Step-by-Step Worked Problem: Methane Combustion with 20% Excess Air

Problem: Industrial natural gas modeled as pure methane ( CH 4 \text{CH}_4 CH 4 ​ ) enters a boiler burner at 25 ∘ C 25^\circ\text{C} 2 5 ∘ C ( 77 ∘ F 77^\circ\text{F} 7 7 ∘ F ) and 1 atm 1\text{ atm} 1 atm and is combusted with 20 % 20\% 20% excess dry air entering at 25 ∘ C 25^\circ\text{C} 2 5 ∘ C . Calculate:

  • The actual balanced chemical reaction equation
  • The actual mass-based Air-Fuel ratio ( ( A / F ) m a s s (A/F)_{mass} ( A / F ) ma ss ​ )
  • The percentage of carbon dioxide ( CO 2 \text{CO}_2 CO 2 ​ ) in the dry flue gas (Orsat basis)

The Higher and Lower Heating Values ( H H V HHV HH V and L H V LHV L H V in kJ/kg \text{kJ/kg} kJ/kg ) +-----------------------------------------------------------------------------------------+

  • | METHANE COMBUSTION CALCULATION STEPS |
  • | |
  • | STEP 1: Stoichiometric Reaction Balancing (CH4 + a_th*(O2 + 3.76 N2)) |
  • | Carbon Balance: 1 CO2 ==> n = 1 |
  • | Hydrogen Balance: 4 H ==> 2 H2O ==> m = 4 |
  • | Oxygen Balance: a_th = n + m/4 = 1 + 4/4 = 2.0 kmol O2 |
  • | Theoretical: CH4 + 2.0 (O2 + 3.76 N2) ---> CO2 + 2 H2O + 7.52 N2 |
  • | |
  • | STEP 2: Actual Reaction with 20% Excess Air (a_act = 1.20 * 2.0 = 2.40 kmol O2) |
  • | CH4 + 2.40 (O2 + 3.76 N2) ---> 1 CO2 + 2 H2O + 0.40 O2 + 9.024 N2 |
  • | |
  • | STEP 3: Actual Mass Air-Fuel Ratio (AF_mass) |
  • | M_fuel = 12.011 + 4*(1.008) = 16.043 kg/kmol |
  • | m_air = 2.40 * 4.76 kmol air * 28.97 kg/kmol = 330.95 kg air |
  • | (A/F)_mass = 330.95 kg air / 16.043 kg fuel = 20.63 kg air / kg fuel |
  • | (Note: Stoichiometric (A/F)_stoich = 2.0 * 4.76 * 28.97 / 16.043 = 17.19) |
  • | |
  • | STEP 4: Dry Flue Gas Orsat Analysis (Exclude 2 moles of H2O) |
  • | N_dry = N_CO2 + N_O2 + N_N2 = 1.0 + 0.40 + 9.024 = 10.424 kmol |
  • | % CO2 (dry) = (1.0 / 10.424) * 100% = 9.59% |
  • | % O2 (dry) = (0.40 / 10.424) * 100% = 3.84% |
  • | % N2 (dry) = (9.024 / 10.424) * 100% = 86.57% |
  • | |
  • | STEP 5: Heating Value Calculations (HHV & LHV) |
  • | LHV_molar = -Delta H_comb (H2O vapor) |
  • | LHV_molar = -[1*(-393520) + 2*(-241820) - 1*(-74850)] |
  • | LHV_molar = -[-393520 - 483640 + 74850] = 802,310 kJ/kmol CH4 |
  • | LHV_mass = 802,310 / 16.043 = 50,010 kJ/kg CH4 |
  • | |
  • | HHV_molar = -Delta H_comb (H2O liquid) |
  • | HHV_molar = -[1*(-393520) + 2*(-285830) - 1*(-74850)] |
  • | HHV_molar = -[-393520 - 571660 + 74850] = 890,330 kJ/kmol CH4 |
  • | HHV_mass = 890,330 / 16.043 = 55,496 kJ/kg CH4 |
  • | |
  • | Difference: HHV - LHV = 55,496 - 50,010 = 5,486 kJ/kg CH4 |
  • | (Matches: 2 kmol H2O * 44,010 kJ/kmol / 16.043 kg = 5,486 kJ/kg) |
  • +-----------------------------------------------------------------------------------------+
  • 7. Common Exam Traps & PE Pro-Tips

Trap 1 — Dry vs. Wet Flue Gas in Orsat Problems: Orsat gas analyzers do not measure water vapor because moisture is intentionally condensed before testing. When converting dry Orsat volume percentages to true wet stack compositions, always multiply by ( 1 − y H 2 O , w e t ) (1 - y_{\text{H}_2\text{O},wet}) ( 1 − y H 2 ​ O , w e t ​ ) .

Trap 2 — Nitrogen Multiplier in Combustion Air: Air contains 3.76 kmol N 2 3.76\text{ kmol } \text{N}_2 3.76 kmol N 2 ​ per kmol O 2 \text{kmol } \text{O}_2 kmol O 2 ​ , which corresponds to 4.76 kmol air / kmol O 2 4.76\text{ kmol air} / \text{kmol } \text{O}_2 4.76 kmol air / kmol O 2 ​ . When computing air moles from oxygen moles, multiply a a c t a_{act} a a c t ​ by 4.76 4.76 4.76 , not 3.76 3.76 3.76 .

Trap 3 — HHV vs LHV Water State: Remember that Higher Heating Value assumes water in the combustion products is fully condensed into liquid at 25 ∘ C 25^\circ\text{C} 2 5 ∘ C (recovering latent heat h f g h_{fg} h f g ​ ), while Lower Heating Value assumes water remains in the vapor phase.