Study guide
5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws
PE Mechanical Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals
1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium
2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)
2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints
3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations
3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing
4 Chapter 4: Thermal & Fluid Systems
4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)
5 Chapter 5: Power Plants & Energy Conversion Systems
5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage
6 Chapter 6: HVAC & Refrigeration Systems
6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation
7 Chapter 7: Materials, Manufacturing & Processing
7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)
8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics
8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability
5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws
Key Takeaways Explain This Topic AI
The State Postulate dictates that the thermodynamic state of a simple compressible system is completely specified by two independent, intensive properties.
In two-phase liquid-vapor regions, intensive properties depend solely on saturation quality: y = y f + x y f g y = y_f + x y_{fg} y = y f + x y f g , where x = m g / m t o t a l x = m_g / m_{total} x = m g / m t o t a l .
The Steady-Flow Energy Equation (SFEE) equates net heat and work inputs to changes in flow enthalpy, kinetic energy, and potential energy across control volumes: Q ˙ − W ˙ c v = ∑ m ˙ e ( h e + V e 2 / 2 + g z e ) − ∑ m ˙ i ( h i + V i 2 / 2 + g z i ) \dot{Q} - \dot{W}_{cv} = \sum \dot{m}_e (h_e + V_e^2/2 + g z_e) - \sum \dot{m}_i (h_i + V_i^2/2 + g z_i) Q ˙ − W ˙ c v = ∑ m ˙ e ( h e + V e 2 /2 + g z e ) − ∑ m ˙ i ( h i + V i 2 /2 + g z i ) .
The Second Law establishes that heat cannot spontaneously transfer from low to high temperature and limits heat engine thermal efficiency to the Carnot bound: η t h , m a x = 1 − T L / T H \eta_{th,max} = 1 - T_L / T_H η t h , ma x = 1 − T L / T H with absolute temperatures in Kelvin or Rankine.
Turbine, compressor, and pump irreversibilities are quantified by isentropic efficiencies, relating actual work to reversible isentropic work between the same boundary pressures.
Last updated: August 2026
Thermodynamic Properties, Pure Substances & 1st/2nd Laws
Thermodynamics forms the governing analytical foundation for all power generation, refrigeration, propulsion, and energy conversion systems. On the NCEES PE Mechanical exam, thermodynamic problems demand rigorous property evaluation, accurate navigation of steam and refrigerant tables, control volume energy balancing, and Second Law entropy accounting. Mastery begins with understanding how thermodynamic states are defined and tracked across phase boundaries.
1. Thermodynamic State Postulate & Phase Equilibrium
The State Postulate establishes that the thermodynamic state of a simple compressible system (a system free from electrical, magnetic, gravitational, and surface tension effects) is completely specified by two independent, intensive properties . +-----------------------------------------------------------------------------------------+
- | THE STATE POSTULATE IN PRACTICE |
- | |
- | SINGLE-PHASE REGIONS (Superheated Vapor, Compressed Liquid): |
- | - Any two independent properties fix the state: (P, T), (P, v), (T, s), (P, h). |
- | - Temperature and pressure are independent: specifying P does NOT determine T. |
- | |
- | TWO-PHASE MIXTURE REGION (Saturated Liquid-Vapor Dome): |
- | - Temperature and pressure are DEPENDENT: T = T_sat(P) and P = P_sat(T). |
- | - Specifying (P, T) gives only ONE independent piece of information. |
- | - A third property is mandatory to fix the state: Quality x, Enthalpy h, Entropy s. |
- +-----------------------------------------------------------------------------------------+
- Pure Substances & Phase Regimes
A pure substance has a fixed chemical composition throughout. Water ( H 2 O \text{H}_2\text{O} H 2 O ), refrigerants (R-134a, R-410A), and dry air (when non-condensing) behave as pure substances. As heat is added at constant pressure, a substance traverses distinct regimes:
Subcooled / Compressed Liquid: The fluid temperature is below the saturation temperature at the given pressure ( T < T s a t T < T_{sat} T < T s a t or P > P s a t P > P_{sat} P > P s a t ). Molecules remain closely bound in the liquid phase.
Saturated Liquid ( f f f ): The liquid is at the verge of boiling ( x = 0 , T = T s a t x = 0, T = T_{sat} x = 0 , T = T s a t ). Any additional heat input initiates vapor generation.
Saturated Liquid-Vapor Mixture: Liquid and vapor coexist in equilibrium ( 0 < x < 1 0 < x < 1 0 < x < 1 ). Temperature and pressure remain locked at T s a t T_{sat} T s a t and P s a t P_{sat} P s a t while phase transformation proceeds.
Saturated Vapor ( g g g ): The liquid is fully vaporized ( x = 1.0 , T = T s a t x = 1.0, T = T_{sat} x = 1.0 , T = T s a t ). Any removal of heat causes condensation.
Superheated Vapor: The vapor temperature is above saturation temperature ( T > T s a t T > T_{sat} T > T s a t or P < P s a t P < P_{sat} P < P s a t ). The vapor behaves increasingly like an ideal gas as pressure decreases and temperature rises.
Supercritical Fluid: At states above the Critical Point ( T > T c , P > P c T > T_c, P > P_c T > T c , P > P c ), distinct liquid and gas phases cease to exist; fluid expands to fill containers without meniscus formation. +-----------------------------------------------------------------------------------------+
- | CRITICAL & TRIPLE POINT CONSTANTS FOR WATER |
- | |
- | Critical Point (Water): P_c = 22.064 MPa (3200.1 psia), T_c = 373.95 °C (705.11 °F)|
- | Triple Point (Water): P_tp = 0.6117 kPa (0.0887 psia), T_tp = 0.01 °C (32.02 °F) |
- +-----------------------------------------------------------------------------------------+
- 2. Property Diagrams & Steam Table Procedures
Engineers visualize thermodynamic processes on two-dimensional coordinate projections: T − v T-v T − v , P − v P-v P − v , T − s T-s T − s , P − h P-h P − h , and the Mollier diagram ( h − s h-s h − s ). T-v Diagram P-h Diagram (Refrigeration)
- T ^ P ^
- | Critical Point | Critical Point
- | /\ | /\
- | / \ P = const | P_cond ---/--\---------------
- | Comp. / \ | / \
- | Liquid / x \ Superheat | Subcooled/ x \ Superheated
- | / \ | Liquid / \ Vapor
- | / \ | P_evap/----------\-----------
- |________/____________\________> |________/____________\__________>
- 0 v 0 h
- Quality & Two-Phase Property Evaluations
Inside the saturation dome, the vapor mass fraction is defined as Quality ( x x x ) : x = m v a p o r m t o t a l = m g m f + m g ( 0 ≤ x ≤ 1 ) x = \frac{m_{vapor}}{m_{total}} = \frac{m_g}{m_f + m_g} \quad (0 \le x \le 1) x = m t o t a l m v a p or = m f + m g m g ( 0 ≤ x ≤ 1 )
Any specific extensive property y ∈ { v , u , h , s } y \in \{v, u, h, s\} y ∈ { v , u , h , s } is evaluated directly from saturation table values ( y f y_f y f for saturated liquid, y g y_g y g for saturated vapor, and y f g = y g − y f y_{fg} = y_g - y_f y f g = y g − y f for the vaporization difference): y = y f + x y f g = y f + x ( y g − y f ) y = y_f + x y_{fg} = y_f + x (y_g - y_f) y = y f + x y f g = y f + x ( y g − y f ) x = y − y f y f g = y − y f y g − y f x = \frac{y - y_f}{y_{fg}} = \frac{y - y_f}{y_g - y_f} x = y f g y − y f = y g − y f y − y f
Compressed Liquid Approximations
Because liquids are essentially incompressible, their thermodynamic properties depend almost entirely on temperature rather than pressure. When compressed liquid tables are unavailable: v ( T , P ) ≈ v f ( T ) v(T, P) \approx v_f(T) v ( T , P ) ≈ v f ( T ) ν ( T , P ) ≈ u f ( T ) \nu(T, P) \approx u_f(T) ν ( T , P ) ≈ u f ( T ) s ( T , P ) ≈ s f ( T ) s(T, P) \approx s_f(T) s ( T , P ) ≈ s f ( T ) h ( T , P ) ≈ h f ( T ) + v f ( T ) [ P − P s a t ( T ) ] h(T, P) \approx h_f(T) + v_f(T) \left[P - P_{sat}(T)\right] h ( T , P ) ≈ h f ( T ) + v f ( T ) [ P − P s a t ( T ) ]
Tip
In low-to-medium pressure applications, h ≈ h f ( T ) h \approx h_f(T) h ≈ h f ( T ) is widely used. However, across high-pressure power plant boiler feed pumps ( P > 5 MPa P > 5\text{ MPa} P > 5 MPa or 750 psia 750\text{ psia} 750 psia ), the Poynting correction term v f Δ P v_f \Delta P v f Δ P is essential to avoid significant enthalpy error.
Linear Interpolation Formula
When looking up unlisted values in steam or refrigerant tables, use two-point linear interpolation: y = y 1 + ( x − x 1 x 2 − x 1 ) ( y 2 − y 1 ) y = y_1 + \left(\frac{x - x_1}{x_2 - x_1}\right)(y_2 - y_1) y = y 1 + ( x 2 − x 1 x − x 1 ) ( y 2 − y 1 )
3. Ideal Gas Relations & Specific Heat Ratios
Gases at low pressures and high temperatures relative to their critical points obey the Ideal Gas Equation of State : P v = R T ⟹ P V = m R T = N R u T P v = R T \implies P V = m R T = N R_u T P v = RT ⟹ P V = m RT = N R u T
Where:
R u = 8.3145 kJ/(kmol ⋅ K) = 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) = 1.9858 BTU/(lbmol ⋅ ∘ R) R_u = 8.3145 \text{ kJ/(kmol}\cdot\text{K)} = 1545.35 \text{ ft}\cdot\text{lbf/(lbmol}\cdot{}^\circ\text{R)} = 1.9858 \text{ BTU/(lbmol}\cdot{}^\circ\text{R)} R u = 8.3145 kJ/(kmol ⋅ K) = 1545.35 ft ⋅ lbf/(lbmol ⋅ ∘ R) = 1.9858 BTU/(lbmol ⋅ ∘ R) is the Universal Gas Constant.
R = R u / M R = R_u / M R = R u / M is the specific gas constant ( R a i r = 0.2870 kJ/(kg ⋅ K) = 53.35 ft ⋅ lbf/(lbm ⋅ ∘ R) R_{air} = 0.2870 \text{ kJ/(kg}\cdot\text{K)} = 53.35 \text{ ft}\cdot\text{lbf/(lbm}\cdot{}^\circ\text{R)} R ai r = 0.2870 kJ/(kg ⋅ K) = 53.35 ft ⋅ lbf/(lbm ⋅ ∘ R) ).
T T T must always be in absolute temperature ( K = ∘ C + 273.15 \text{K} = {}^\circ\text{C} + 273.15 K = ∘ C + 273.15 or ∘ R = ∘ F + 459.67 {}^\circ\text{R} = {}^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 ). +-----------------------------------------------------------------------------------------+
- | IDEAL GAS SPECIFIC HEAT RELATIONS |
- | |
- | Mayer's Equation: c_p - c_v = R |
- | Specific Heat Ratio: k = c_p / c_v |
- | Component Formulas: c_v = R / (k - 1), c_p = k * R / (k - 1) |
- | |
- | Standard Air (300 K): k = 1.40, c_p = 1.005 kJ/(kg*K) = 0.240 BTU/(lbm*°R) |
- | c_v = 0.718 kJ/(kg*K) = 0.171 BTU/(lbm*°R) |
- +-----------------------------------------------------------------------------------------+
- 4. The First Law of Thermodynamics: Closed & Open Systems
The First Law enforces the principle of conservation of energy.
Closed Systems (Non-Flow Processes)
For a stationary closed system with fixed mass: Δ U + Δ K E + Δ P E = Q i n − W o u t \Delta U + \Delta KE + \Delta PE = Q_{in} - W_{out} Δ U + Δ K E + Δ PE = Q in − W o u t
Where boundary work W b = ∫ 1 2 P d V W_b = \int_1^2 P dV W b = ∫ 1 2 P d V depends on the process path:
Process Type Governing Path Boundary Work Expression ( W b W_b W b )
Isobaric P = constant P = \text{constant} P = constant W b = P ( V 2 − V 1 ) = m R ( T 2 − T 1 ) W_b = P(V_2 - V_1) = m R (T_2 - T_1) W b = P ( V 2 − V 1 ) = m R ( T 2 − T 1 )
Isochoric V = constant V = \text{constant} V = constant W b = 0 ⟹ Q = Δ U = m c v ( T 2 − T 1 ) W_b = 0 \implies Q = \Delta U = m c_v (T_2 - T_1) W b = 0 ⟹ Q = Δ U = m c v ( T 2 − T 1 )
Isothermal (Ideal Gas) T = constant T = \text{constant} T = constant W b = P 1 V 1 ln ( V 2 V 1 ) = m R T ln ( P 1 P 2 ) W_b = P_1 V_1 \ln\left(\frac{V_2}{V_1}\right) = m R T \ln\left(\frac{P_1}{P_2}\right) W b = P 1 V 1 ln ( V 1 V 2 ) = m RT ln ( P 2 P 1 )
Polytropic ( n ≠ 1 n \ne 1 n = 1 ) P V n = constant P V^n = \text{constant} P V n = constant W b = P 2 V 2 − P 1 V 1 1 − n = m R ( T 2 − T 1 ) 1 − n W_b = \frac{P_2 V_2 - P_1 V_1}{1 - n} = \frac{m R (T_2 - T_1)}{1 - n} W b = 1 − n P 2 V 2 − P 1 V 1 = 1 − n m R ( T 2 − T 1 )
Isentropic (Reversible Adiabatic) P v k = constant P v^k = \text{constant} P v k = constant W b = P 2 V 2 − P 1 V 1 1 − k = m R ( T 2 − T 1 ) 1 − k = − Δ U W_b = \frac{P_2 V_2 - P_1 V_1}{1 - k} = \frac{m R (T_2 - T_1)}{1 - k} = -\Delta U W b = 1 − k P 2 V 2 − P 1 V 1 = 1 − k m R ( T 2 − T 1 ) = − Δ U
Open Systems: Steady-Flow Energy Equation (SFEE)
For a steady-state, steady-flow control volume with negligible potential energy changes: Q ˙ − W ˙ c v = ∑ m ˙ e ( h e + V e 2 2 + g z e ) − ∑ m ˙ i ( h i + V i 2 2 + g z i ) \dot{Q} - \dot{W}_{cv} = \sum \dot{m}_e \left(h_e + \frac{V_e^2}{2} + g z_e\right) - \sum \dot{m}_i \left(h_i + \frac{V_i^2}{2} + g z_i\right) Q ˙ − W ˙ c v = ∑ m ˙ e ( h e + 2 V e 2 + g z e ) − ∑ m ˙ i ( h i + 2 V i 2 + g z i ) +-----------------------------------------------------------------------------------------+
- | STEADY-FLOW EQUATIONS FOR COMMON POWER COMPONENTS |
- | |
- | TURBINES: w_t = h_1 - h_2 (Adiabatic, negligible delta KE) |
- | COMPRESSORS / PUMPS: w_c = h_2 - h_1 (Work input required) |
- | INCOMPRESSIBLE PUMP: w_p = v_f * (P_2 - P_1) (Liquid specific volume v_f) |
- | NOZZLES (Accelerating):V_2 = sqrt(2*(h_1 - h_2) + V_1^2) (Converts enthalpy to kinetic)|
- | DIFFUSERS (Decelerating): h_2 - h_1 = (V_1^2 - V_2^2) / 2 (Converts kinetic to enthalpy)|
- | THROTTLING VALVES: h_1 = h_2 (Isenthalpic, Q=0, W=0) |
- | HEAT EXCHANGERS: m_hot*(h_h1 - h_h2) = m_cold*(h_c2 - h_c1) |
- +-----------------------------------------------------------------------------------------+
Warning
Nozzle Velocity Units in US Customary: In English units, enthalpy is in BTU/lbm \text{BTU/lbm} BTU/lbm and velocity is in ft/s \text{ft/s} ft/s . To balance units under the square root, apply the conversion factor g c J = 32.174 × 778.17 = 25 , 037 ft 2 / ( s 2 ⋅ BTU ) g_c J = 32.174 \times 778.17 = 25,037 \text{ ft}^2/(\text{s}^2\cdot\text{BTU}) g c J = 32.174 × 778.17 = 25 , 037 ft 2 / ( s 2 ⋅ BTU ) : V 2 = 2 g c J ( h 1 − h 2 ) + V 1 2 = 50 , 074 ( h 1 − h 2 ) + V 1 2 V_2 = \sqrt{2 g_c J (h_1 - h_2) + V_1^2} = \sqrt{50,074 (h_1 - h_2) + V_1^2} V 2 = 2 g c J ( h 1 − h 2 ) + V 1 2 = 50 , 074 ( h 1 − h 2 ) + V 1 2
5. The Second Law of Thermodynamics, Entropy & Exergy
The Second Law dictates the direction of spontaneous processes and establishes theoretical performance ceilings. +-----------------------------------------------------------------------------------------+
- | SECOND LAW CLASSICAL STATEMENTS |
- | |
- | KELVIN-PLANCK STATEMENT: |
- | It is impossible for any device that operates on a thermodynamic cycle to receive |
- | heat from a single thermal reservoir and produce a net amount of work. |
- | --> Eliminates 100% efficient heat engines (Perpetual Motion Machines of the 2nd Kind)|
- | |
- | CLAUSIUS STATEMENT: |
- | It is impossible to construct a cyclic device that transfers heat from a lower- |
- | temperature body to a higher-temperature body without external work input. |
- | --> Requires work input for refrigerators and heat pumps. |
- +-----------------------------------------------------------------------------------------+
- Carnot Maximum Efficiency
The Carnot cycle represents the maximum theoretical thermal efficiency for any heat engine operating between a high-temperature thermal reservoir at T H T_H T H and a low-temperature sink at T L T_L T L : η t h , C a r n o t = 1 − T L T H ( T L , T H strictly in absolute units: K or ∘ R ) \eta_{th,Carnot} = 1 - \frac{T_L}{T_H} \quad (T_L, T_H \text{ strictly in absolute units: K or } {}^\circ\text{R}) η t h , C a r n o t = 1 − T H T L ( T L , T H strictly in absolute units: K or ∘ R )
Clausius Inequality & Entropy Change
For any thermodynamic cycle, the Clausius Inequality holds: ∮ δ Q T ≤ 0 ( = for internally reversible, < for irreversible ) \oint \frac{\delta Q}{T} \le 0 \quad (=\text{ for internally reversible, } <\text{ for irreversible}) ∮ T δ Q ≤ 0 ( = for internally reversible, < for irreversible )
Entropy S S S is a thermodynamic property defined differentially as d S = ( δ Q / T ) r e v dS = (\delta Q / T)_{rev} d S = ( δ Q / T ) re v . For an isolated system or universe, entropy continuously increases: Δ S i s o l a t e d = S g e n ≥ 0 \Delta S_{isolated} = S_{gen} \ge 0 Δ S i so l a t e d = S g e n ≥ 0 .
Entropy Calculations for Ideal Gases
For an ideal gas with constant specific heats: Δ s = s 2 − s 1 = c p ln ( T 2 T 1 ) − R ln ( P 2 P 1 ) = c v ln ( T 2 T 1 ) + R ln ( v 2 v 1 ) \Delta s = s_2 - s_1 = c_p \ln\left(\frac{T_2}{T_1}\right) - R \ln\left(\frac{P_2}{P_1}\right) = c_v \ln\left(\frac{T_2}{T_1}\right) + R \ln\left(\frac{v_2}{v_1}\right) Δ s = s 2 − s 1 = c p ln ( T 1 T 2 ) − R ln ( P 1 P 2 ) = c v ln ( T 1 T 2 ) + R ln ( v 1 v 2 )
For an isentropic process ( s 1 = s 2 , Δ s = 0 s_1 = s_2, \Delta s = 0 s 1 = s 2 , Δ s = 0 ): T 2 T 1 = ( P 2 P 1 ) k − 1 k = ( v 1 v 2 ) k − 1 ⟹ P v k = constant \frac{T_2}{T_1} = \left(\frac{P_2}{P_1}\right)^{\frac{k-1}{k}} = \left(\frac{v_1}{v_2}\right)^{k-1} \implies P v^k = \text{constant} T 1 T 2 = ( P 1 P 2 ) k k − 1 = ( v 2 v 1 ) k − 1 ⟹ P v k = constant
Component Isentropic Efficiencies
Real-world turbines, compressors, and pumps suffer from frictional dissipation, turbulence, and heat loss, departing from ideal isentropic behavior. Turbine Expansion (h-s) Compressor Compression (h-s)
- h ^ h ^
- | State 1 | State 2a (Actual)
- | * | *
- | | \ | /|
- | | \ Actual Path | State 2s / |
- | | * State 2a | * / |
- | * (h2a > h2s) | | / |
- | State 2s | | / |
- | (s2s = s1) | *---------+---- State 1
+------------------------> s +------------------------> s η turbine = w a c t u a l w i s e n t r o p i c = h 1 − h 2 a h 1 − h 2 s \eta_{\text{turbine}} = \frac{w_{actual}}{w_{isentropic}} = \frac{h_1 - h_{2a}}{h_1 - h_{2s}} η turbine = w i se n t ro p i c w a c t u a l = h 1 − h 2 s h 1 − h 2 a η compressor = w i s e n t r o p i c w a c t u a l = h 2 s − h 1 h 2 a − h 1 \eta_{\text{compressor}} = \frac{w_{isentropic}}{w_{actual}} = \frac{h_{2s} - h_1}{h_{2a} - h_1} η compressor = w a c t u a l w i se n t ro p i c = h 2 a − h 1 h 2 s − h 1 η pump = w i s e n t r o p i c w a c t u a l = v f ( P 2 − P 1 ) h 2 a − h 1 \eta_{\text{pump}} = \frac{w_{isentropic}}{w_{actual}} = \frac{v_f (P_2 - P_1)}{h_{2a} - h_1} η pump = w a c t u a l w i se n t ro p i c = h 2 a − h 1 v f ( P 2 − P 1 )
Exergy & Availability
Exergy ( X X X ) is the maximum theoretical useful work obtainable as a system comes into thermodynamic equilibrium with an environmental dead state ( T 0 , P 0 T_0, P_0 T 0 , P 0 ). The specific flow exergy ( ψ \psi ψ ) is: ψ = ( h − h 0 ) − T 0 ( s − s 0 ) + V 2 2 + g z \psi = (h - h_0) - T_0 (s - s_0) + \frac{V^2}{2} + g z ψ = ( h − h 0 ) − T 0 ( s − s 0 ) + 2 V 2 + g z
By the Gouy-Stodola Theorem , the rate of exergy destroyed (irreversibility I ˙ \dot{I} I ˙ ) is directly proportional to the rate of entropy generation: X ˙ d e s t r o y e d = I ˙ = T 0 S ˙ g e n \dot{X}_{destroyed} = \dot{I} = T_0 \dot{S}_{gen} X ˙ d es t roye d = I ˙ = T 0 S ˙ g e n
6. Step-by-Step Worked Problem: Steam Turbine Expansion
Problem: A steady-flow adiabatic steam turbine in a central power station receives superheated steam at P 1 = 8.0 MPa P_1 = 8.0\text{ MPa} P 1 = 8.0 MPa ( 1160 psia 1160\text{ psia} 1160 psia ) and T 1 = 500 ∘ C T_1 = 500^\circ\text{C} T 1 = 50 0 ∘ C ( 932 ∘ F 932^\circ\text{F} 93 2 ∘ F ). The steam expands to an exhaust condenser pressure of P 2 = 20 kPa P_2 = 20\text{ kPa} P 2 = 20 kPa ( 2.9 psia 2.9\text{ psia} 2.9 psia ). The turbine has an isentropic efficiency of η t = 88 % \eta_t = 88\% η t = 88% . The mass flow rate is m ˙ = 30 kg/s \dot{m} = 30\text{ kg/s} m ˙ = 30 kg/s . Calculate:
The ideal isentropic enthalpy at turbine exit ( h 2 s h_{2s} h 2 s )
The actual power output produced by the turbine ( W ˙ a c t u a l \dot{W}_{actual} W ˙ a c t u a l in MW \text{MW} MW )
The actual moisture content ( 1 − x 2 a 1 - x_{2a} 1 − x 2 a ) of the exhaust steam +-----------------------------------------------------------------------------------------+
- | STEAM TURBINE CALCULATION STEPS |
- | |
- | STEP 1: Turbine Inlet State Evaluation (Superheated Steam Tables at 8 MPa, 500 °C) |
- | h_1 = 3399.5 kJ/kg |
- | s_1 = 6.7266 kJ/(kg*K) |
- | |
- | STEP 2: Ideal Isentropic Exit State 2s (P_2 = 20 kPa, s_2s = s_1 = 6.7266 kJ/(kg*K)) |
- | From Saturation Tables at 20 kPa: |
- | T_sat = 60.06 °C, s_f = 0.8320 kJ/(kg*K), s_fg = 7.0752 kJ/(kg*K) |
- | h_f = 251.40 kJ/kg, h_fg = 2357.5 kJ/kg |
- | |
- | Isentropic Quality: |
- | x_2s = (s_2s - s_f) / s_fg = (6.7266 - 0.8320) / 7.0752 = 0.83314 |
- | |
- | Isentropic Exit Enthalpy: |
- | h_2s = h_f + x_2s * h_fg = 251.40 + 0.83314 * (2357.5) = 2215.53 kJ/kg |
- | |
- | STEP 3: Actual Enthalpy Drop & Power Generation |
- | Ideal Specific Work: |
- | w_s = h_1 - h_2s = 3399.5 - 2215.53 = 1183.97 kJ/kg |
- | |
- | Actual Specific Work: |
- | w_a = eta_t * w_s = 0.88 * 1183.97 = 1041.89 kJ/kg |
- | |
- | Actual Total Power Output: |
- | W_dot = m_dot * w_a = 30 kg/s * 1041.89 kJ/kg = 31,256.7 kW = 31.26 MW |
- | |
- | STEP 4: Actual Exhaust State & Moisture Content |
- | Actual Exit Enthalpy: |
- | h_2a = h_1 - w_a = 3399.5 - 1041.89 = 2357.61 kJ/kg |
- | |
- | Actual Exit Quality: |
- | x_2a = (h_2a - h_f) / h_fg = (2357.61 - 251.40) / 2357.5 = 0.8934 |
- | |
- | Moisture Content (Moisture Fraction = 1 - x_2a): |
- | Moisture % = (1 - 0.8934) * 100% = 10.66% |
- +-----------------------------------------------------------------------------------------+
- 7. Common Exam Traps & PE Pro-Tips
Trap 1 — Incompressible Work Assumption on High-Pressure Pumps: In low-pressure HVAC pumping, w p = v Δ P w_p = v \Delta P w p = v Δ P is negligible. But across modern supercritical or subcritical boiler feed pumps ( P 2 = 10 − 25 MPa P_2 = 10 - 25\text{ MPa} P 2 = 10 − 25 MPa ), pump work exceeds 10 − 30 kJ/kg 10 - 30\text{ kJ/kg} 10 − 30 kJ/kg and cannot be omitted in cycle thermal balances.
Trap 2 — Temperature Units in Second Law Equations: Whenever evaluating Carnot efficiencies, entropy relations Δ s = c p ln ( T 2 / T 1 ) \Delta s = c_p \ln(T_2/T_1) Δ s = c p ln ( T 2 / T 1 ) , or exergy dead states T 0 T_0 T 0 , always convert Celsius to Kelvin ( K = ∘ C + 273.15 \text{K} = {}^\circ\text{C} + 273.15 K = ∘ C + 273.15 ) or Fahrenheit to Rankine ( ∘ R = ∘ F + 459.67 {}^\circ\text{R} = {}^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 ).
Trap 3 — Superheated Region Property Independence: Within the saturation dome, pressure and temperature are completely coupled; you cannot use ( P , T ) (P, T) ( P , T ) to fix a state. In the superheated vapor and compressed liquid regions, however, pressure and temperature are independent.