Study guide

3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels

Key Takeaways Explain This Topic AI

Hydrodynamic journal bearing operation is governed by the dimensionless Sommerfeld number S = ( r / c ) 2 ( μ N ′ / P ) S = (r/c)^2 (\mu N' / P) S = ( r / c ) 2 ( μ N ′ / P ) ; high S S S indicates stable full fluid-film lubrication, whereas low S S S warns of boundary lubrication, metal-to-metal asperity contact, and bearing wipe.

Rolling-element bearing L 10 L_{10} L 10 ​ rating life scales inversely with the equivalent dynamic load P e = X V F r + Y F a P_e = X V F_r + Y F_a P e ​ = X V F r ​ + Y F a ​ raised to exponent p p p ( p = 3 p=3 p = 3 for ball bearings, p = 10 / 3 p=10/3 p = 10/3 for roller bearings): L 10 = ( C / P e ) p × 10 6 L_{10} = (C/P_e)^p \times 10^6 L 10 ​ = ( C / P e ​ ) p × 1 0 6 revolutions.

Disc clutches and brakes are designed using the conservative uniform wear model ( p ⋅ r = const p \cdot r = \text{const} p ⋅ r = const ) for broken-in surfaces, resulting in clamping force F = 2 π p max ⁡ r i ( r o − r i ) F = 2\pi p_{\max} r_i (r_o - r_i) F = 2 π p m a x ​ r i ​ ( r o ​ − r i ​ ) and torque capacity T = N μ F ( r o + r i ) / 2 T = N \mu F (r_o + r_i)/2 T = N μ F ( r o ​ + r i ​ ) /2 .

Band brakes obey the exponential capstan friction relation T 1 / T 2 = e μ θ T_1 / T_2 = e^{\mu \theta} T 1 ​ / T 2 ​ = e μ θ (with θ \theta θ in radians); power screws raise a load with torque T R = F d m 2 l + π f d m π d m − f l T_R = \frac{F d_m}{2}\frac{l + \pi f d_m}{\pi d_m - f l} T R ​ = 2 F d m ​ ​ π d m ​ − f l l + π f d m ​ ​ and are self-locking when the friction angle ϕ = tan ⁡ − 1 f \phi = \tan^{-1} f ϕ = tan − 1 f exceeds the helix angle λ \lambda λ .

Flywheel sizing balances cyclic kinetic energy fluctuation Δ E \Delta E Δ E to limit the coefficient of speed fluctuation C s = ( ω 1 − ω 2 ) / ω avg C_s = (\omega_1 - \omega_2)/\omega_{\text{avg}} C s ​ = ( ω 1 ​ − ω 2 ​ ) / ω avg ​ via I = Δ E / ( C s ω avg 2 ) I = \Delta E / (C_s \omega_{\text{avg}}^2) I = Δ E / ( C s ​ ω avg 2 ​ ) , while rim hoop stress is constrained to σ = ρ ( ω R ) 2 \sigma = \rho (\omega R)^2 σ = ρ ( ω R ) 2 .

Last updated: August 2026

Rolling-Element Bearings, Hydrodynamic Journal Bearings, Clutches & Brakes

Machine assemblies require specialized mechanical components to support rotating shafts, regulate speed, absorb kinetic energy, and smooth torque fluctuations. This section provides complete coverage of four major machine elements tested on the PE Mechanical exam: hydrodynamic journal bearings , rolling-element bearings ( L 10 L_{10} L 10 ​ fatigue life) , friction clutches and brakes (disc, band, drum) , and flywheel inertia sizing and rim stresses . +---------------------------------------------------------------------------------------------------+

  • | POWER TRANSMISSION COMPONENT ARCHITECTURE |
  • | |
  • | [JOURNAL BEARINGS] [ROLLING BEARINGS] [CLUTCHES & BRAKES] [FLYWHEELS] |
  • | - Hydrodynamic Film - Ball / Roller Elements - Uniform Wear / Press - Energy Storage |
  • | - Sommerfeld Number (S) - Basic Dynamic Load (C) - Disc / Drum / Band - Fluctuation (C_s) |
  • | - Petroff Friction - L10 Life (p=3, 10/3) - Capstan: T1/T2=e^(mu*t)- Inertia Sizing |
  • | - Thermal Dissipation - Eq Load: P = X*Fr+Y*Fa - Thermal Dissipation - Rim Hoop Stress |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Hydrodynamic Lubrication & Journal Bearings

In a hydrodynamic journal bearing, shaft rotation drags viscous lubricant into a converging clearance wedge between the journal (shaft) and the bushing, generating sufficient hydrodynamic pressure to support external radial loads without solid metal-to-metal contact. +---------------------------------------------------------------------------------------------------+

  • | HYDRODYNAMIC JOURNAL BEARING GEOMETRY |
  • | |
  • | +-----------------------+ |
  • | / \ |
  • | / STATIONARY BUSHING \ |
  • | | (Radius R) | |
  • | | +---------------+ | |
  • | | / \ | |
  • | | / ROTATING JOURNAL \ | Radial Clearance: c = R - r |
  • | | | (Radius r) | | Eccentricity: e |
  • | | \ / | Min Film: h_0 = c - e |
  • | | \ w (Rotation) / | Eccentricity Ratio: eps = e/c |
  • | \ +---------------+ / |
  • | \ / |
  • | +-----------------------+ |
  • +---------------------------------------------------------------------------------------------------+
  • The Stribeck Curve & Lubrication Regimes

The lubrication regime is governed by the bearing characteristic parameter μ N ′ P \frac{\mu N'}{P} P μ N ′ ​ :

Boundary Lubrication (Low μ N ′ / P \mu N'/P μ N ′ / P ): Solid asperity contact carries the load ( f ≈ 0.08 − 0.15 f \approx 0.08 - 0.15 f ≈ 0.08 − 0.15 ). High wear occurs during startup/shutdown.

Mixed-Film Lubrication: Intermediate regime with partial asperity contact and partial hydrodynamic pressure.

Hydrodynamic (Full-Film) Lubrication (High μ N ′ / P \mu N'/P μ N ′ / P ): A continuous fluid film separates surfaces completely ( f ≈ 0.001 − 0.005 f \approx 0.001 - 0.005 f ≈ 0.001 − 0.005 ). Zero mechanical wear.

1. Petroff's Equation (Concentric Journal Friction)

For a lightly loaded, high-speed concentric journal bearing ( e ≈ 0 e \approx 0 e ≈ 0 ), Petroff's equation gives the frictional torque T f T_f T f ​ and coefficient of friction f f f : T f = 4 π 2 μ r 3 l N ′ c T_f = \frac{4 \pi^2 \mu r^3 l N'}{c} T f ​ = c 4 π 2 μ r 3 l N ′ ​ f = 2 π 2 ( r c ) ( μ N ′ P ) f = 2 \pi^2 \left( \frac{r}{c} \right) \left( \frac{\mu N'}{P} \right) f = 2 π 2 ( c r ​ ) ( P μ N ′ ​ )

Where:

μ = Dynamic viscosity (Pa ⋅ s in SI; reyns = lbf ⋅ s/in 2 in US Customary, with 1 reyn = 6.895 × 10 6 cP) \mu = \text{Dynamic viscosity (}\text{Pa}\cdot\text{s in SI; } \text{reyns} = \text{lbf}\cdot\text{s/in}^2 \text{ in US Customary, with } 1\text{ reyn} = 6.895 \times 10^6\text{ cP)} μ = Dynamic viscosity ( Pa ⋅ s in SI; reyns = lbf ⋅ s/in 2 in US Customary, with 1 reyn = 6.895 × 1 0 6 cP)

r = Journal radius r = \text{Journal radius} r = Journal radius , l = Bearing axial length l = \text{Bearing axial length} l = Bearing axial length , c = Radial clearance = R − r c = \text{Radial clearance} = R - r c = Radial clearance = R − r

N ′ = Rotational speed in rev/s = N / 60 N' = \text{Rotational speed in rev/s} = N / 60 N ′ = Rotational speed in rev/s = N /60

P = Projected bearing pressure = W 2 r l = W d l P = \text{Projected bearing pressure} = \frac{W}{2 r l} = \frac{W}{d l} P = Projected bearing pressure = 2 r l W ​ = d l W ​

2. The Sommerfeld Number ( S S S )

The dimensionless Sommerfeld number (Bearing Characteristic Number) is the master design parameter for hydrodynamic journal bearings: S = ( r c ) 2 ( μ N ′ P ) S = \left( \frac{r}{c} \right)^2 \left( \frac{\mu N'}{P} \right) S = ( c r ​ ) 2 ( P μ N ′ ​ )

Using Raimondi-Boyd charts with S S S and length-to-diameter ratio ( l / d l/d l / d ):

Minimum film thickness: h 0 = c ( 1 − ϵ ) h_0 = c (1 - \epsilon) h 0 ​ = c ( 1 − ϵ ) , where ϵ = e / c \epsilon = e/c ϵ = e / c is the eccentricity ratio.

Friction variable: ( r c ) f ⟹ f \left(\frac{r}{c}\right) f \implies f ( c r ​ ) f ⟹ f .

Power Loss: H loss = 2 π N ′ T f = f W ( 2 π r N ′ ) H_{\text{loss}} = 2\pi N' T_f = f W (2\pi r N') H loss ​ = 2 π N ′ T f ​ = f W ( 2 π r N ′ ) .

Lubricant Temperature Rise: Δ T = H loss m ˙ c p \Delta T = \frac{H_{\text{loss}}}{\dot{m} c_p} Δ T = m ˙ c p ​ H loss ​ ​ , where m ˙ = ρ Q \dot{m} = \rho Q m ˙ = ρQ is the lubricant mass flow rate.

2. Rolling-Element Bearings & L 10 L_{10} L 10 ​ Fatigue Life

Rolling contact bearings replace sliding friction with rolling elements (balls or rollers). Bearing life is limited by subsurface shear fatigue spalling. +---------------------------------------------------------------------------------------------------+

  • | ROLLING-ELEMENT BEARING TYPES |
  • | |
  • | DEEP GROOVE BALL: CYLINDRICAL ROLLER: TAPERED ROLLER: SPHERICAL ROLLER: |
  • | - Radial + moderate axial- High radial capacity - Heavy combined loads - Self-aligning |
  • | - Low friction / high spd- Zero thrust capacity - Radial + high thrust - Heavy radial loads |
  • | - Life exponent p = 3 - Life exponent p = 10/3 - Used in preloaded pairs- Angular tolerance |
  • +---------------------------------------------------------------------------------------------------+
  • Equivalent Radial Dynamic Load ( P e P_e P e ​ )

When a bearing experiences simultaneous radial load F r F_r F r ​ and axial thrust load F a F_a F a ​ : P e = X V F r + Y F a P_e = X V F_r + Y F_a P e ​ = X V F r ​ + Y F a ​

Where:

V = Rotation factor ( 1.0 for rotating inner ring; 1.2 for rotating outer ring) V = \text{Rotation factor (}1.0\text{ for rotating inner ring; } 1.2\text{ for rotating outer ring)} V = Rotation factor ( 1.0 for rotating inner ring; 1.2 for rotating outer ring)

X = Radial factor X = \text{Radial factor} X = Radial factor and Y = Thrust factor Y = \text{Thrust factor} Y = Thrust factor (from manufacturer tables based on F a / ( V F r ) > e F_a / (V F_r) > e F a ​ / ( V F r ​ ) > e )

If F a / ( V F r ) ≤ e F_a / (V F_r) \le e F a ​ / ( V F r ​ ) ≤ e , then X = 1.0 X = 1.0 X = 1.0 and Y = 0 Y = 0 Y = 0 , so P e = V F r P_e = V F_r P e ​ = V F r ​ .

L 10 L_{10} L 10 ​ Rating Life Sizing Equations

The basic rating life L 10 L_{10} L 10 ​ (the operating life completed or exceeded by 90 % 90\% 90% of identical bearings before first evidence of fatigue) is: L 10 = ( C P e ) p × 10 6 ( revolutions ) L_{10} = \left( \frac{C}{P_e} \right)^p \times 10^6 \quad (\text{revolutions}) L 10 ​ = ( P e ​ C ​ ) p × 1 0 6 ( revolutions ) L 10 h = 10 6 60 N ( C P e ) p ( operating hours ) L_{10h} = \frac{10^6}{60 N} \left( \frac{C}{P_e} \right)^p \quad (\text{operating hours}) L 10 h ​ = 60 N 1 0 6 ​ ( P e ​ C ​ ) p ( operating hours )

Where:

C = Basic dynamic load rating (load for 10 6 revolutions) C = \text{Basic dynamic load rating (load for } 10^6 \text{ revolutions)} C = Basic dynamic load rating (load for 1 0 6 revolutions)

P e = Equivalent radial dynamic load P_e = \text{Equivalent radial dynamic load} P e ​ = Equivalent radial dynamic load

N = Rotational speed in rpm N = \text{Rotational speed in rpm} N = Rotational speed in rpm

p = 3.0 for ball bearings p = 3.0 \text{ for ball bearings} p = 3.0 for ball bearings ; p = 10 3 ≈ 3.333 for roller bearings p = \frac{10}{3} \approx 3.333 \text{ for roller bearings} p = 3 10 ​ ≈ 3.333 for roller bearings

Reliability and Adjusted Life ( L n a L_{na} L na ​ )

For reliability levels other than 90 % 90\% 90% ( R > 0.90 R > 0.90 R > 0.90 ): L n a = a 1 a 2 a 3 L 10 L_{na} = a_1 a_2 a_3 L_{10} L na ​ = a 1 ​ a 2 ​ a 3 ​ L 10 ​

  • Desired Reliability ( R R R ) Reliability Factor ( a 1 a_1 a 1 ​ ) Probability of Failure
  • 90 % 90\% 90% 1.00 1.00 1.00 10 % 10\% 10%
  • 95 % 95\% 95% 0.64 0.64 0.64 5 % 5\% 5%
  • 97 % 97\% 97% 0.47 0.47 0.47 3 % 3\% 3%
  • 99 % 99\% 99% 0.21 0.21 0.21 1 % 1\% 1%
  • 3. Clutches & Disc Brakes: Uniform Wear vs. Uniform Pressure

Friction clutches and disc brakes transmit torque through mechanical contact over annular friction surfaces ( r i ≤ r ≤ r o r_i \le r \le r_o r i ​ ≤ r ≤ r o ​ ). +---------------------------------------------------------------------------------------------------+

  • | ANNULAR DISC CLUTCH / BRAKE GEOMETRY |
  • | |
  • | +-----------------------+ |
  • | / Outer Radius (r_o) \ |
  • | / +---------------+ \ |
  • | | / Inner Rad (r_i)\ | Friction Surfaces: N |
  • | | | (Bore) | | Friction Coeff: mu |
  • | | \ / | Max Pressure: p_max |
  • | \ +---------------+ / Axial Clamping Force: F |
  • | \ / |
  • | +-----------------------+ |
  • +---------------------------------------------------------------------------------------------------+
  • Model 1: Uniform Wear Model (Broken-In Surfaces)

Wear is assumed proportional to frictional work ( P V = const ⟹ p ⋅ r = C = p max ⁡ r i PV = \text{const} \implies p \cdot r = C = p_{\max} r_i P V = const ⟹ p ⋅ r = C = p m a x ​ r i ​ ). Maximum pressure occurs at inner radius r i r_i r i ​ . This is the standard, conservative model for design: F = 2 π p max ⁡ r i ( r o − r i ) F = 2 \pi p_{\max} r_i (r_o - r_i) F = 2 π p m a x ​ r i ​ ( r o ​ − r i ​ ) T = N μ F r avg = N μ F ( r o + r i 2 ) = π N μ p max ⁡ r i ( r o 2 − r i 2 ) T = N \mu F r_{\text{avg}} = N \mu F \left( \frac{r_o + r_i}{2} \right) = \pi N \mu p_{\max} r_i (r_o^2 - r_i^2) T = N μ F r avg ​ = N μ F ( 2 r o ​ + r i ​ ​ ) = π N μ p m a x ​ r i ​ ( r o 2 ​ − r i 2 ​ )

Where N = Number of active friction interface pairs N = \text{Number of active friction interface pairs} N = Number of active friction interface pairs (for M M M driving plates and K K K driven plates, N = M + K − 1 N = M + K - 1 N = M + K − 1 ).

Model 2: Uniform Pressure Model (Brand New Surfaces)

Assumes rigid, perfectly flat new plates with uniform pressure distribution ( p = p max ⁡ = const p = p_{\max} = \text{const} p = p m a x ​ = const ): F = π p max ⁡ ( r o 2 − r i 2 ) F = \pi p_{\max} (r_o^2 - r_i^2) F = π p m a x ​ ( r o 2 ​ − r i 2 ​ ) T = 2 3 N μ F ( r o 3 − r i 3 r o 2 − r i 2 ) = 2 3 π N μ p max ⁡ ( r o 3 − r i 3 ) T = \frac{2}{3} N \mu F \left( \frac{r_o^3 - r_i^3}{r_o^2 - r_i^2} \right) = \frac{2}{3} \pi N \mu p_{\max} (r_o^3 - r_i^3) T = 3 2 ​ N μ F ( r o 2 ​ − r i 2 ​ r o 3 ​ − r i 3 ​ ​ ) = 3 2 ​ π N μ p m a x ​ ( r o 3 ​ − r i 3 ​ )

Important

Optimal Disc Geometry Ratio: To maximize torque capacity for a given maximum outer radius r o r_o r o ​ under the uniform wear model, set d d r i [ r i ( r o 2 − r i 2 ) ] = r o 2 − 3 r i 2 = 0 ⟹ r i r o = 1 3 ≈ 0.577 \frac{d}{dr_i}[r_i (r_o^2 - r_i^2)] = r_o^2 - 3 r_i^2 = 0 \implies \frac{r_i}{r_o} = \frac{1}{\sqrt{3}} \approx 0.577 d r i ​ d ​ [ r i ​ ( r o 2 ​ − r i 2 ​ )] = r o 2 ​ − 3 r i 2 ​ = 0 ⟹ r o ​ r i ​ ​ = 3 ​ 1 ​ ≈ 0.577 .

4. Band Brakes & Drum Brakes +---------------------------------------------------------------------------------------------------+

  • | BAND BRAKE MECHANICS |
  • | |
  • | T_1 (Tight Side Tension) |
  • | ^ |
  • | | Wrap Angle (theta rad) |
  • | +-----+-----+ |
  • | / \ |
  • | | DRUM ROTATION | ---> Torque T = (T_1 - T_2) * r |
  • | \ / |
  • | +-----+-----+ |
  • | | |
  • | v |
  • | T_2 (Slack Side Tension) |
  • | |
  • | CAPSTAN FORMULA: T_1 / T_2 = e^(mu * theta) ===> T_1 = T_2 * e^(mu * theta) |
  • +---------------------------------------------------------------------------------------------------+
  • Band Brake Governing Equations

Capstan Friction Tension Ratio: T 1 T 2 = e μ θ \frac{T_1}{T_2} = e^{\mu \theta} T 2 ​ T 1 ​ ​ = e μ θ (Where θ \theta θ is the band wrap angle in radians , and T 1 T_1 T 1 ​ is tight side tension opposing drum rotation) .

Braking Torque Transmitted: T brake = ( T 1 − T 2 ) r = T 2 ( e μ θ − 1 ) r T_{\text{brake}} = (T_1 - T_2) r = T_2 (e^{\mu \theta} - 1) r T brake ​ = ( T 1 ​ − T 2 ​ ) r = T 2 ​ ( e μ θ − 1 ) r

Actuating Force: Solved from lever moment equilibrium ∑ M pivot = 0 \sum M_{\text{pivot}} = 0 ∑ M pivot ​ = 0 .

Self-Locking Phenomenon: In a differential band brake, if friction assists the actuating force such that F actuate ≤ 0 F_{\text{actuate}} \le 0 F actuate ​ ≤ 0 , the brake locks automatically upon contact without external operator force.

Brake Energy Dissipation & Temperature Rise

When absorbing kinetic energy Δ E k \Delta E_k Δ E k ​ from moving mass m m m or rotating inertia I I I : Δ E k = 1 2 m ( v 1 2 − v 2 2 ) + 1 2 I ( ω 1 2 − ω 2 2 ) \Delta E_k = \frac{1}{2} m (v_1^2 - v_2^2) + \frac{1}{2} I (\omega_1^2 - \omega_2^2) Δ E k ​ = 2 1 ​ m ( v 1 2 ​ − v 2 2 ​ ) + 2 1 ​ I ( ω 1 2 ​ − ω 2 2 ​ ) Δ T = Δ E k m drum c p \Delta T = \frac{\Delta E_k}{m_{\text{drum}} c_p} Δ T = m drum ​ c p ​ Δ E k ​ ​

5. Flywheel Energy Storage & Rim Stresses

Flywheels smooth cyclic torque variations in reciprocating machinery by storing kinetic energy during excess torque phases and delivering it during peak demands. +---------------------------------------------------------------------------------------------------+

  • | FLYWHEEL CRANK-TORQUE DIAGRAM |
  • | |
  • | Torque |
  • | ^ +---------------+ (Peak Torque) |
  • | | / \ |
  • | | / Excess Work \ |
  • | | / (+Delta E) \ |
  • | T_mean =====+=======================+============================= (Mean Resisting Load) |
  • | | \ / |
  • | | \ Deficit Work / |
  • | | \ (-Delta E) / |
  • | +-------------+---------------+--------------------------> Crank Angle Theta (rad) |
  • +---------------------------------------------------------------------------------------------------+

1. Coefficient of Speed Fluctuation ( C s C_s C s ​ ) C s = ω 1 − ω 2 ω avg = N 1 − N 2 N avg C_s = \frac{\omega_1 - \omega_2}{\omega_{\text{avg}}} = \frac{N_1 - N_2}{N_{\text{avg}}} C s ​ = ω avg ​ ω 1 ​ − ω 2 ​ ​ = N avg ​ N 1 ​ − N 2 ​ ​

Where ω avg = ω 1 + ω 2 2 \omega_{\text{avg}} = \frac{\omega_1 + \omega_2}{2} ω avg ​ = 2 ω 1 ​ + ω 2 ​ ​ (Standard values: C s = 0.01 − 0.02 C_s = 0.01 - 0.02 C s ​ = 0.01 − 0.02 for generators; C s = 0.05 − 0.10 C_s = 0.05 - 0.10 C s ​ = 0.05 − 0.10 for punch presses).

2. Sizing Required Mass Moment of Inertia ( I I I )

The maximum energy change Δ E \Delta E Δ E is: Δ E = 1 2 I ( ω 1 2 − ω 2 2 ) = I C s ω avg 2 ⟹ I = Δ E C s ω avg 2 \Delta E = \frac{1}{2} I (\omega_1^2 - \omega_2^2) = I C_s \omega_{\text{avg}}^2 \implies I = \frac{\Delta E}{C_s \omega_{\text{avg}}^2} Δ E = 2 1 ​ I ( ω 1 2 ​ − ω 2 2 ​ ) = I C s ​ ω avg 2 ​ ⟹ I = C s ​ ω avg 2 ​ Δ E ​

3. Flywheel Rim Geometry and Hoop Stress

For a rim-type flywheel where mass is concentrated in a rim of mean radius R R R ( I ≈ m rim R 2 I \approx m_{\text{rim}} R^2 I ≈ m rim ​ R 2 ): m rim = I R 2 = ρ ( 2 π R b t ) m_{\text{rim}} = \frac{I}{R^2} = \rho (2\pi R b t) m rim ​ = R 2 I ​ = ρ ( 2 π R b t )

Centrifugal acceleration induces tensile hoop stress σ t \sigma_t σ t ​ in the thin rim: σ t = ρ v 2 = ρ ( ω R ) 2 \sigma_t = \rho v^2 = \rho (\omega R)^2 σ t ​ = ρ v 2 = ρ ( ω R ) 2

Where ρ \rho ρ is mass density ( kg/m 3 \text{kg/m}^3 kg/m 3 or slug/in 3 \text{slug/in}^3 slug/in 3 ) and v = ω R v = \omega R v = ω R is rim linear speed.

6. Power Screws & Threaded Linear Actuation

The Machine Design and Materials specification groups power screws with belts, chains, clutches, and brakes under Power Transmission. A power screw converts input rotation and torque into linear motion and force — jack screws, C-clamps, vises, valve stems, and machine-tool lead screws are the classic exam applications.

Thread Geometry Terminology

Pitch ( p p p ): axial distance between adjacent thread crests.

Lead ( l l l ): axial advance per screw revolution. Single-start thread: l = p l = p l = p ; double-start: l = 2 p l = 2p l = 2 p .

Helix angle ( λ \lambda λ ): tan ⁡ λ = l / ( π d m ) \tan\lambda = l / (\pi d_m) tan λ = l / ( π d m ​ ) , measured at the mean (pitch) thread diameter d m d_m d m ​ .

Thread forms: square threads maximize efficiency and strength per turn; Acme (29° included angle) threads are cheaper to machine and self-centering; buttress threads carry heavy loads in one direction; ball screws replace sliding friction with rolling contact.

Torque to Raise and Lower the Load

Raising a load F F F against thread friction requires input torque: T R = F d m 2 ( l + π f d m π d m − f l ) + T collar , T collar = F f c d c 2 T_R = \frac{F\, d_m}{2}\left(\frac{l + \pi f d_m}{\pi d_m - f l}\right) + T_{\text{collar}}, \qquad T_{\text{collar}} = \frac{F f_c d_c}{2} T R ​ = 2 F d m ​ ​ ( π d m ​ − f l l + π f d m ​ ​ ) + T collar ​ , T collar ​ = 2 F f c ​ d c ​ ​

where f f f is the thread coefficient of friction and the collar term accounts for any thrust-bearing surface of mean diameter d c d_c d c ​ . The lowering expression flips the friction terms in sign — but a self-locking screw still needs torque to pay friction going down.

Friction Angle, Efficiency & the Self-Locking Condition

Define the friction angle ϕ = tan ⁡ − 1 f \phi = \tan^{-1} f ϕ = tan − 1 f . Thread efficiency is: ≠ = F l 2 π T R = tan ⁡ λ tan ⁡ ( λ + ϕ ) \ne = \frac{F l}{2 \pi T_R} = \frac{\tan\lambda}{\tan(\lambda + \phi)}  = = 2 π T R ​ Fl ​ = tan ( λ + ϕ ) tan λ ​

Self-locking condition: ϕ > λ \phi > \lambda ϕ > λ (efficiency below 50%). A self-locking screw holds the applied load with zero sustaining input torque — jacks do not back-drive.

Ball screws reach e ≈ 90 % e \approx 90\% e ≈ 90% and are therefore back-drivable ; vertical axes need a holding brake or counterweight.

Long slender screws loaded in compression must also clear column buckling (Euler/Johnson criteria from Section 2.4) — thread strength alone is not sufficient.

Worked Mini-Example

A single-start square-thread jack screw has d m = 20 mm d_m = 20\text{ mm} d m ​ = 20 mm , p = l = 5 mm p = l = 5\text{ mm} p = l = 5 mm , μ = 0.10 \mu = 0.10 μ = 0.10 (collar friction neglected), lifting F = 10 kN F = 10\text{ kN} F = 10 kN :

λ = tan ⁡ − 1 ( 5 / ( 20 π ) ) = 4.55 ° \lambda = \tan^{-1}(5 / (20\pi)) = 4.55° λ = tan − 1 ( 5/ ( 20 π )) = 4.55° ; ϕ = tan ⁡ − 1 ( 0.10 ) = 5.71 ° \phi = \tan^{-1}(0.10) = 5.71° ϕ = tan − 1 ( 0.10 ) = 5.71° .

ϕ > λ \phi > \lambda ϕ > λ → self-locking ✓ (the jack holds the 10 kN with the handle released).

T R = F d m 2 tan ⁡ ( λ + ϕ ) = 10,000 × 0.020 2 × tan ⁡ ( 10.26 ° ) = 100 × 0.181 ≈ 18.1 N ⋅ m T_R = \frac{F d_m}{2}\tan(\lambda + \phi) = \frac{10{,}000 \times 0.020}{2} \times \tan(10.26°) = 100 \times 0.181 \approx 18.1\text{ N}\cdot \text{m} T R ​ = 2 F d m ​ ​ tan ( λ + ϕ ) = 2 10 , 000 × 0.020 ​ × tan ( 10.26° ) = 100 × 0.181 ≈ 18.1 N ⋅ m .

e = tan ⁡ ( 4.55 ° ) / tan ⁡ ( 10.26 ° ) = 0.0796 / 0.181 ≈ 0.44 e = \tan(4.55°) / \tan(10.26°) = 0.0796 / 0.181 \approx 0.44 e = tan ( 4.55° ) / tan ( 10.26° ) = 0.0796/0.181 ≈ 0.44 (44%).

  • 7. Step-by-Step Worked Problem: Rolling Bearing Life & Flywheel Sizing
  • Problem Statement

A cylindrical roller bearing ( C = 54 kN C = 54\text{ kN} C = 54 kN , p = 10 / 3 p = 10/3 p = 10/3 ) operates at 1500 rpm 1500\text{ rpm} 1500 rpm under a purely radial load F r = 9.0 kN F_r = 9.0\text{ kN} F r ​ = 9.0 kN ( V = 1.0 V = 1.0 V = 1.0 ). Compute the L 10 h L_{10h} L 10 h ​ rating life in operating hours.

A punch press requires energy absorption Δ E = 3600 J \Delta E = 3600\text{ J} Δ E = 3600 J per stroke. Mean speed is 240 rpm 240\text{ rpm} 240 rpm , and speed fluctuation must not exceed C s = 0.04 C_s = 0.04 C s ​ = 0.04 . Sizing a steel rim flywheel ( ρ = 7850 kg/m 3 \rho = 7850\text{ kg/m}^3 ρ = 7850 kg/m 3 ) with mean radius R = 0.60 m R = 0.60\text{ m} R = 0.60 m , determine the required mass moment of inertia I I I , required rim mass m rim m_{\text{rim}} m rim ​ , and the resulting rim hoop stress σ t \sigma_t σ t ​ .

  • Step-by-Step Solution
  • Part 1: Roller Bearing Life Calculation

Equivalent dynamic load: P e = F r = 9.0 kN P_e = F_r = 9.0\text{ kN} P e ​ = F r ​ = 9.0 kN .

Compute L 10 L_{10} L 10 ​ in millions of revolutions (for roller bearings, p = 10 / 3 = 3.333 p = 10/3 = 3.333 p = 10/3 = 3.333 ): L 10 = ( C P e ) 10 / 3 = ( 54 9.0 ) 3.333 = ( 6.0 ) 3.333 = 390.1 million revs L_{10} = \left( \frac{C}{P_e} \right)^{10/3} = \left( \frac{54}{9.0} \right)^{3.333} = (6.0)^{3.333} = 390.1\text{ million revs} L 10 ​ = ( P e ​ C ​ ) 10/3 = ( 9.0 54 ​ ) 3.333 = ( 6.0 ) 3.333 = 390.1 million revs

Convert to operating hours at N = 1500 rpm N = 1500\text{ rpm} N = 1500 rpm : L 10 h = L 10 × 10 6 60 N = 390.1 × 10 6 60 × 1500 = 3.901 × 10 8 9.0 × 10 4 = 4 , 334 hours L_{10h} = \frac{L_{10} \times 10^6}{60 N} = \frac{390.1 \times 10^6}{60 \times 1500} = \frac{3.901 \times 10^8}{9.0 \times 10^4} = \mathbf{4,334\text{ hours}} L 10 h ​ = 60 N L 10 ​ × 1 0 6 ​ = 60 × 1500 390.1 × 1 0 6 ​ = 9.0 × 1 0 4 3.901 × 1 0 8 ​ = 4 , 334 hours

Part 2: Flywheel Sizing Calculation

Mean angular velocity: ω avg = 2 π ( 240 ) 60 = 25.133 rad/s \omega_{\text{avg}} = \frac{2\pi (240)}{60} = 25.133\text{ rad/s} ω avg ​ = 60 2 π ( 240 ) ​ = 25.133 rad/s .

Required mass moment of inertia: I = Δ E C s ω avg 2 = 3600 J 0.04 × ( 25.133 ) 2 = 3600 0.04 × 631.65 = 3600 25.266 = 142.48 kg ⋅ m 2 I = \frac{\Delta E}{C_s \omega_{\text{avg}}^2} = \frac{3600\text{ J}}{0.04 \times (25.133)^2} = \frac{3600}{0.04 \times 631.65} = \frac{3600}{25.266} = \mathbf{142.48\text{ kg}\cdot\text{m}^2} I = C s ​ ω avg 2 ​ Δ E ​ = 0.04 × ( 25.133 ) 2 3600 J ​ = 0.04 × 631.65 3600 ​ = 25.266 3600 ​ = 142.48 kg ⋅ m 2

Required rim mass (at R = 0.60 m R = 0.60\text{ m} R = 0.60 m ): m rim = I R 2 = 142.48 ( 0.60 ) 2 = 142.48 0.36 = 395.8 kg m_{\text{rim}} = \frac{I}{R^2} = \frac{142.48}{(0.60)^2} = \frac{142.48}{0.36} = \mathbf{395.8\text{ kg}} m rim ​ = R 2 I ​ = ( 0.60 ) 2 142.48 ​ = 0.36 142.48 ​ = 395.8 kg

Rim linear speed: v = ω R = ( 25.133 ) ( 0.60 ) = 15.08 m/s v = \omega R = (25.133)(0.60) = 15.08\text{ m/s} v = ω R = ( 25.133 ) ( 0.60 ) = 15.08 m/s .

Rim hoop tensile stress: σ t = ρ v 2 = ( 7850 kg/m 3 ) × ( 15.08 m/s ) 2 = 7850 × 227.4 = 1.785 × 10 6 Pa = 1.79 MPa \sigma_t = \rho v^2 = (7850\text{ kg/m}^3) \times (15.08\text{ m/s})^2 = 7850 \times 227.4 = 1.785 \times 10^6\text{ Pa} = \mathbf{1.79\text{ MPa}} σ t ​ = ρ v 2 = ( 7850 kg/m 3 ) × ( 15.08 m/s ) 2 = 7850 × 227.4 = 1.785 × 1 0 6 Pa = 1.79 MPa (Well within allowable limit for cast iron/steel, typically σ allow ≈ 30 − 50 MPa \sigma_{\text{allow}} \approx 30 - 50\text{ MPa} σ allow ​ ≈ 30 − 50 MPa ) .

8. Exam Tips & Common Traps

Tip

Speedy Exam Rules:

In band brake capstan calculations ( e μ θ e^{\mu\theta} e μ θ ), wrap angle θ \theta θ must always be in radians ( 180 ∘ = π rad 180^\circ = \pi\text{ rad} 18 0 ∘ = π rad ). Degrees will give massive exponential errors.

For rolling bearings, double-check whether the problem specifies a ball bearing ( p = 3 p=3 p = 3 ) or a roller bearing ( p = 10 / 3 p=10/3 p = 10/3 ). Doubling load on a ball bearing reduces life by 2 3 = 8 × 2^3 = 8\times 2 3 = 8 × , while on a roller bearing it reduces life by 2 3.333 = 10.08 × 2^{3.333} = 10.08\times 2 3.333 = 10.08 × .

Warning

Common Traps:

Clutch Pressure Model Trap: Unless a problem explicitly specifies "brand new, rigid flat plates," always use the uniform wear model . Uniform pressure overestimates capacity and only applies before initial wear occurs.

Flywheel Percentage Fluctuation: If C s C_s C s ​ is given as 3 % 3\% 3% , use 0.03 0.03 0.03 in equations, not 0.3 0.3 0.3 .