Study guide

3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains

Key Takeaways Explain This Topic AI

Involute gear geometry is governed by Diametral Pitch P = N / d P = N/d P = N / d (teeth/in) or Module m = d / N m = d/N m = d / N (mm/tooth), with circular pitch p = π / P = π m p = \pi/P = \pi m p = π / P = πm and base pitch p b = p cos ⁡ ϕ p_b = p \cos\phi p b ​ = p cos ϕ .

To eliminate interference and root undercutting during hobbing of standard 20 ∘ 20^\circ 2 0 ∘ full-depth spur gears, the minimum pinion tooth count is N min ⁡ = 2 k sin ⁡ 2 ( 20 ∘ ) = 18 N_{\min} = \frac{2k}{\sin^2(20^\circ)} = 18 N m i n ​ = s i n 2 ( 2 0 ∘ ) 2 k ​ = 18 teeth ( 12 12 12 teeth for 25 ∘ 25^\circ 2 5 ∘ ).

Gear tooth forces decompose into transmitted tangential force W t = 2 T / d W_t = 2T/d W t ​ = 2 T / d , radial separating force W r = W t tan ⁡ ϕ t W_r = W_t \tan\phi_t W r ​ = W t ​ tan ϕ t ​ , and axial thrust force W a = W t tan ⁡ ψ W_a = W_t \tan\psi W a ​ = W t ​ tan ψ (for helical gears) or W a = W t tan ⁡ ϕ sin ⁡ γ W_a = W_t \tan\phi \sin\gamma W a ​ = W t ​ tan ϕ sin γ (for bevel gears).

AGMA rating decouples gear failure into root bending fatigue ( σ b ∝ W t \sigma_b \propto W_t σ b ​ ∝ W t ​ ) and surface Hertzian contact pitting ( σ c ∝ W t \sigma_c \propto \sqrt{W_t} σ c ​ ∝ W t ​ ​ ); doubling torque doubles bending stress ( 2.0 × 2.0\times 2.0 × ) but increases contact stress by only 2 ≈ 1.414 × \sqrt{2} \approx 1.414\times 2 ​ ≈ 1.414 × .

Epicyclic (planetary) gear train velocity ratios are resolved using the Willis relative formula n L − n C n F − n C = e train \frac{n_L - n_C}{n_F - n_C} = e_{\text{train}} n F ​ − n C ​ n L ​ − n C ​ ​ = e train ​ with carrier speed n C n_C n C ​ , sun, planet, and ring gears satisfying N R = N S + 2 N P N_R = N_S + 2 N_P N R ​ = N S ​ + 2 N P ​ .

Last updated: August 2026

Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains

Gears are toothed cylindrical or conical mechanical elements designed to transmit positive, non-slip angular velocity and mechanical torque between rotating shafts. On the NCEES PE Mechanical exam, gear problems evaluate five fundamental competencies: involute tooth geometry and conjugate action , kinematic interference and undercutting limits , static and dynamic 3D tooth force resolution , AGMA fatigue ratings (tooth root bending vs. surface pitting) , and compound/planetary gear train kinematics . +---------------------------------------------------------------------------------------------------+

  • | GEAR CLASSIFICATION & CHARACTERISTICS |
  • | |
  • | SPUR GEARS: HELICAL GEARS: BEVEL GEARS: WORM GEARSETS: |
  • | - Parallel shafts - Parallel / Crossed - Intersecting shafts - Non-intersecting |
  • | - Straight axial teeth - Inclined helix angle - Conical pitch surface - 90 deg shaft angle |
  • | - Zero axial thrust - High contact ratio - Combined thrust/radial - High ratio (10-100) |
  • | - Low cost / standard - Quiet & smooth mesh - Shaft angle (Sigma=90) - Self-locking action |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Fundamentals of Involute Gear Tooth Geometry

Modern gears utilize the involute of a circle tooth profile because it satisfies the Fundamental Law of Gearing : the common normal to the tooth profiles at all points of contact must pass through a fixed pitch point ( P P P ) , ensuring a strictly constant angular velocity ratio ( m V = ω in / ω out = const m_V = \omega_{\text{in}}/\omega_{\text{out}} = \text{const} m V ​ = ω in ​ / ω out ​ = const ) regardless of center distance variation. +---------------------------------------------------------------------------------------------------+

  • | INVOLUTE SPUR GEAR TOOTH NOMENCLATURE |
  • | |
  • | Addendum Circle (d_a = d + 2a) |
  • | --------------------------------------------- |
  • | ^ |
  • | Addendum | a = 1/P = 1.0 m |
  • | v Pitch Circle (d = N/P = m*N) |
  • | =========================+============================================ |
  • | ^ |
  • | Dedendum | b = 1.25/P = 1.25 m |
  • | v Base Circle (d_b = d * cos(phi)) |
  • | --------------------------------------------- |
  • | Dedendum / Root Circle (d_r = d - 2b) |
  • | --------------------------------------------- |
  • | |
  • | Circular Pitch: p = pi*d / N = pi/P = pi*m | Base Pitch: p_b = p * cos(phi) |
  • | Whole Depth: h_t = a + b = 2.25/P | Clearance: c = b - a = 0.25/P |
  • +---------------------------------------------------------------------------------------------------+
  • Essential Geometric Equations

Parameter US Customary Formula SI Metric Formula Definition & Significance

Diametral Pitch ( P P P ) P = N d P = \frac{N}{d} P = d N ​ P = 25.4 m P = \frac{25.4}{m} P = m 25.4 ​ Teeth per inch of pitch diameter

Module ( m m m ) m = 25.4 P m = \frac{25.4}{P} m = P 25.4 ​ m = d N m = \frac{d}{N} m = N d ​ Millimeters of pitch diameter per tooth

Pitch Diameter ( d d d ) d = N P d = \frac{N}{P} d = P N ​ d = m N d = m N d = m N Operating reference diameter

Circular Pitch ( p p p ) p = π d N = π P p = \frac{\pi d}{N} = \frac{\pi}{P} p = N π d ​ = P π ​ p = π m p = \pi m p = πm Arc length between adjacent tooth centers ( p ⋅ P = π p \cdot P = \pi p ⋅ P = π )

Base Circle ( d b d_b d b ​ ) d b = d cos ⁡ ϕ d_b = d \cos\phi d b ​ = d cos ϕ d b = d cos ⁡ ϕ d_b = d \cos\phi d b ​ = d cos ϕ Diameter where involute generation begins

Base Pitch ( p b p_b p b ​ ) p b = p cos ⁡ ϕ p_b = p \cos\phi p b ​ = p cos ϕ p b = p cos ⁡ ϕ p_b = p \cos\phi p b ​ = p cos ϕ Distance between teeth along the line of action

Addendum ( a a a ) a = 1.0 P a = \frac{1.0}{P} a = P 1.0 ​ a = 1.0 m a = 1.0 m a = 1.0 m Radial height above pitch circle (full depth)

Dedendum ( b b b ) b = 1.25 P b = \frac{1.25}{P} b = P 1.25 ​ b = 1.25 m b = 1.25 m b = 1.25 m Radial depth below pitch circle

Center Distance ( C C C ) C = N P + N G 2 P C = \frac{N_P + N_G}{2 P} C = 2 P N P ​ + N G ​ ​ C = m ( N P + N G ) 2 C = \frac{m(N_P + N_G)}{2} C = 2 m ( N P ​ + N G ​ ) ​ Nominal shaft centerline spacing

Interference, Undercutting & Minimum Pinion Teeth

When generating teeth with a rack cutter or hob, if the addendum of the generating rack extends inside the tangency point of the base circle, the cutter cuts away ("undercuts") the flank of the tooth, severely weakening the root fillet. To prevent undercutting in standard full-depth spur gears: N min ⁡ = 2 k sin ⁡ 2 ϕ N_{\min} = \frac{2 k}{\sin^2\phi} N m i n ​ = sin 2 ϕ 2 k ​

Where k = 1.0 k = 1.0 k = 1.0 for standard full-depth teeth and k = 0.8 k = 0.8 k = 0.8 for stub teeth:

For ϕ = 20 ∘ \phi = 20^\circ ϕ = 2 0 ∘ full-depth ( k = 1 k=1 k = 1 ): N min ⁡ = 2 ( 1 ) sin ⁡ 2 ( 20 ∘ ) = 2 0.11698 = 17.1 ⟹ 18 teeth N_{\min} = \frac{2(1)}{\sin^2(20^\circ)} = \frac{2}{0.11698} = 17.1 \implies \mathbf{18\text{ teeth}} N m i n ​ = s i n 2 ( 2 0 ∘ ) 2 ( 1 ) ​ = 0.11698 2 ​ = 17.1 ⟹ 18 teeth .

For ϕ = 25 ∘ \phi = 25^\circ ϕ = 2 5 ∘ full-depth ( k = 1 k=1 k = 1 ): N min ⁡ = 2 ( 1 ) sin ⁡ 2 ( 25 ∘ ) = 2 0.17861 = 11.2 ⟹ 12 teeth N_{\min} = \frac{2(1)}{\sin^2(25^\circ)} = \frac{2}{0.17861} = 11.2 \implies \mathbf{12\text{ teeth}} N m i n ​ = s i n 2 ( 2 5 ∘ ) 2 ( 1 ) ​ = 0.17861 2 ​ = 11.2 ⟹ 12 teeth .

For ϕ = 14.5 ∘ \phi = 14.5^\circ ϕ = 14. 5 ∘ full-depth ( k = 1 k=1 k = 1 , obsolete): N min ⁡ = 2 ( 1 ) sin ⁡ 2 ( 14.5 ∘ ) = 31.9 ⟹ 32 teeth N_{\min} = \frac{2(1)}{\sin^2(14.5^\circ)} = 31.9 \implies \mathbf{32\text{ teeth}} N m i n ​ = s i n 2 ( 14. 5 ∘ ) 2 ( 1 ) ​ = 31.9 ⟹ 32 teeth .

2. Pitch Line Velocity and 3D Tooth Force Resolution

Power is transmitted at the pitch circle at linear pitch line velocity V V V : V = π d P N P 12 ( ft/min in US Customary, with d P in inches, N P in rpm ) V = \frac{\pi d_P N_P}{12} \quad (\text{ft/min in US Customary, with } d_P \text{ in inches, } N_P \text{ in rpm}) V = 12 π d P ​ N P ​ ​ ( ft/min in US Customary, with d P ​ in inches, N P ​ in rpm ) V = π d P N P 60 × 1000 ( m/s in SI, with d P in mm, N P in rpm ) V = \frac{\pi d_P N_P}{60 \times 1000} \quad (\text{m/s in SI, with } d_P \text{ in mm, } N_P \text{ in rpm}) V = 60 × 1000 π d P ​ N P ​ ​ ( m/s in SI, with d P ​ in mm, N P ​ in rpm ) +---------------------------------------------------------------------------------------------------+

  • | GEAR TOOTH FORCE VECTORS |
  • | |
  • | SPUR GEAR TOOTH FORCES: HELICAL GEAR TOOTH FORCES: |
  • | |
  • | W (Total Normal Load) W_a (Axial Thrust = W_t*tan(psi)|
  • | /| <------ |
  • | / | | \ |
  • | / | W_r = W_t * tan(phi) | \ |
  • | / | W_r = W_t*tan(phi_t) \ |
  • | /phi | | \ W (Total Normal) |
  • | +-----+ | phi_t\ |
  • | W_t (Tangential Load) +-------+ |
  • | W_t |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Spur Gear Force Resolution

Tangential Force ( W t W_t W t ​ ): Transmits power and driving torque T T T . W t = 33000 P hp V = 2 T d P ( US: W t in lbf ) ∣ W t = 1000 P kW V = 2 T d P ( SI: W t in N ) W_t = \frac{33000 P_{\text{hp}}}{V} = \frac{2 T}{d_P} \quad (\text{US: } W_t \text{ in lbf}) \quad \Big| \quad W_t = \frac{1000 P_{\text{kW}}}{V} = \frac{2 T}{d_P} \quad (\text{SI: } W_t \text{ in N}) W t ​ = V 33000 P hp ​ ​ = d P ​ 2 T ​ ( US: W t ​ in lbf ) ​ W t ​ = V 1000 P kW ​ ​ = d P ​ 2 T ​ ( SI: W t ​ in N )

Radial Separating Force ( W r W_r W r ​ ): Pushes gear shafts apart, loading support bearings. W r = W t tan ⁡ ϕ W_r = W_t \tan\phi W r ​ = W t ​ tan ϕ

Total Normal Force ( W W W ): Acts perpendicular to the tooth involute along the line of action. W = W t cos ⁡ ϕ = W t 2 + W r 2 W = \frac{W_t}{\cos\phi} = \sqrt{W_t^2 + W_r^2} W = cos ϕ W t ​ ​ = W t 2 ​ + W r 2 ​ ​

2. Helical Gear Force Resolution

Helical teeth are cut at helix angle ψ \psi ψ . Transverse pressure angle ϕ t \phi_t ϕ t ​ and normal pressure angle ϕ n \phi_n ϕ n ​ are related by: tan ⁡ ϕ t = tan ⁡ ϕ n cos ⁡ ψ \tan\phi_t = \frac{\tan\phi_n}{\cos\psi} tan ϕ t ​ = cos ψ tan ϕ n ​ ​ Normal Pitch: P n = P t cos ⁡ ψ , p n = p t cos ⁡ ψ \text{Normal Pitch: } P_n = \frac{P_t}{\cos\psi}, \quad p_n = p_t \cos\psi Normal Pitch: P n ​ = cos ψ P t ​ ​ , p n ​ = p t ​ cos ψ

Tangential Load: W t = 2 T d P W_t = \frac{2 T}{d_P} W t ​ = d P ​ 2 T ​

Axial (Thrust) Load: W a = W t tan ⁡ ψ W_a = W_t \tan\psi W a ​ = W t ​ tan ψ (requires thrust bearings or herringbone double-helical teeth to cancel)

Radial Separating Load: W r = W t tan ⁡ ϕ t = W t tan ⁡ ϕ n cos ⁡ ψ W_r = W_t \tan\phi_t = W_t \frac{\tan\phi_n}{\cos\psi} W r ​ = W t ​ tan ϕ t ​ = W t ​ c o s ψ t a n ϕ n ​ ​

Total Resultant Normal Load: W = W t cos ⁡ ϕ n cos ⁡ ψ = W t 2 + W r 2 + W a 2 W = \frac{W_t}{\cos\phi_n \cos\psi} = \sqrt{W_t^2 + W_r^2 + W_a^2} W = c o s ϕ n ​ c o s ψ W t ​ ​ = W t 2 ​ + W r 2 ​ + W a 2 ​ ​

3. Straight Bevel Gear Force Resolution

Bevel gears operate on intersecting shafts (typically at shaft angle Σ = 90 ∘ \Sigma = 90^\circ Σ = 9 0 ∘ ). Pitch cone angles satisfy tan ⁡ γ = N P N G \tan\gamma = \frac{N_P}{N_G} tan γ = N G ​ N P ​ ​ (pinion) and tan ⁡ Γ = N G N P \tan\Gamma = \frac{N_G}{N_P} tan Γ = N P ​ N G ​ ​ (gear).

Tangential Force: W t = 2 T d avg W_t = \frac{2 T}{d_{\text{avg}}} W t ​ = d avg ​ 2 T ​ (acting at midpoint of tooth face)

Radial Separating Force (Pinion): W r P = W t tan ⁡ ϕ cos ⁡ γ W_{rP} = W_t \tan\phi \cos\gamma W r P ​ = W t ​ tan ϕ cos γ

Axial Thrust Force (Pinion): W a P = W t tan ⁡ ϕ sin ⁡ γ W_{aP} = W_t \tan\phi \sin\gamma W a P ​ = W t ​ tan ϕ sin γ

(Note: For 90 ∘ 90^\circ 9 0 ∘ shaft angle, W a P = W r G W_{aP} = W_{rG} W a P ​ = W r G ​ and W r P = W a G W_{rP} = W_{aG} W r P ​ = W a G ​ )

4. Worm Gearset Forces & Efficiency

A worm gearset transmits power between non-intersecting, perpendicular shafts. Ratio m G = N G N W m_G = \frac{N_G}{N_W} m G ​ = N W ​ N G ​ ​ (where N W N_W N W ​ is number of worm starts: 1, 2, 3, or 4). Lead angle λ \lambda λ satisfies tan ⁡ λ = L π d W = N W p x π d W \tan\lambda = \frac{L}{\pi d_W} = \frac{N_W p_x}{\pi d_W} tan λ = π d W ​ L ​ = π d W ​ N W ​ p x ​ ​ .

Equilibrium Relations: W t , W = W a , G W_{t,W} = W_{a,G} W t , W ​ = W a , G ​ , W a , W = W t , G W_{a,W} = W_{t,G} W a , W ​ = W t , G ​ , and W r , W = W r , G W_{r,W} = W_{r,G} W r , W ​ = W r , G ​ .

Mesh Efficiency with Friction μ \mu μ : η = cos ⁡ ϕ n − μ tan ⁡ λ cos ⁡ ϕ n + μ cot ⁡ λ \eta = \frac{\cos\phi_n - \mu \tan\lambda}{\cos\phi_n + \mu \cot\lambda} η = cos ϕ n ​ + μ cot λ cos ϕ n ​ − μ tan λ ​

Self-Locking Condition: The gearset cannot be backdriven by the gear when tan ⁡ λ ≤ μ \tan\lambda \le \mu tan λ ≤ μ (typically λ < 5 ∘ \lambda < 5^\circ λ < 5 ∘ ).

3. AGMA Tooth Root Bending Fatigue Rating

Gear teeth act as short cantilever beams. The AGMA bending stress equation modifies the classic Lewis formula with empirical dynamic and geometry correction factors: σ b = W t K o K v K s P F K m K B J ≤ S t Y N S F Y θ Y Z ( US Customary ) \sigma_b = W_t K_o K_v K_s \frac{P}{F} \frac{K_m K_B}{J} \le \frac{S_t Y_N}{S_F Y_\theta Y_Z} \quad (\text{US Customary}) σ b ​ = W t ​ K o ​ K v ​ K s ​ F P ​ J K m ​ K B ​ ​ ≤ S F ​ Y θ ​ Y Z ​ S t ​ Y N ​ ​ ( US Customary ) σ b = W t b m K A K v K s K H 1 Y J ≤ σ F P Y N S F Y θ Y Z ( SI Metric ) \sigma_b = \frac{W_t}{b m} K_A K_v K_s K_H \frac{1}{Y_J} \le \frac{\sigma_{FP} Y_N}{S_F Y_\theta Y_Z} \quad (\text{SI Metric}) σ b ​ = bm W t ​ ​ K A ​ K v ​ K s ​ K H ​ Y J ​ 1 ​ ≤ S F ​ Y θ ​ Y Z ​ σ FP ​ Y N ​ ​ ( SI Metric )

Where:

W t = Transmitted tangential load (lbf or N) W_t = \text{Transmitted tangential load (lbf or N)} W t ​ = Transmitted tangential load (lbf or N)

P = Diametral pitch ( in − 1 ) P = \text{Diametral pitch (}\text{in}^{-1}\text{)} P = Diametral pitch ( in − 1 ) , m = Module (mm) m = \text{Module (mm)} m = Module (mm)

F = b = Face width (in or mm) F = b = \text{Face width (in or mm)} F = b = Face width (in or mm) (Standard range: 9 P ≤ F ≤ 14 P \frac{9}{P} \le F \le \frac{14}{P} P 9 ​ ≤ F ≤ P 14 ​ )

J = Y J = AGMA Bending Geometry Factor (incorporates Lewis form factor Y and root stress concentration K f ) J = Y_J = \text{AGMA Bending Geometry Factor (incorporates Lewis form factor } Y \text{ and root stress concentration } K_f\text{)} J = Y J ​ = AGMA Bending Geometry Factor (incorporates Lewis form factor Y and root stress concentration K f ​ )

K o = K A = Overload / Application factor (1.0 uniform, 1.50 moderate shock, 2.0+ heavy shock) K_o = K_A = \text{Overload / Application factor (1.0 uniform, 1.50 moderate shock, 2.0+ heavy shock)} K o ​ = K A ​ = Overload / Application factor (1.0 uniform, 1.50 moderate shock, 2.0+ heavy shock)

K v = Dynamic factor (accounts for tooth pitch errors and pitch-line velocity vibration) K_v = \text{Dynamic factor (accounts for tooth pitch errors and pitch-line velocity vibration)} K v ​ = Dynamic factor (accounts for tooth pitch errors and pitch-line velocity vibration)

K s = Size factor (1.0 for standard pitches) K_s = \text{Size factor (1.0 for standard pitches)} K s ​ = Size factor (1.0 for standard pitches)

K m = K H = Load distribution factor (accounts for shaft deflection and face crowning) K_m = K_H = \text{Load distribution factor (accounts for shaft deflection and face crowning)} K m ​ = K H ​ = Load distribution factor (accounts for shaft deflection and face crowning)

K B = Rim thickness factor (1.0 for solid gear webs) K_B = \text{Rim thickness factor (1.0 for solid gear webs)} K B ​ = Rim thickness factor (1.0 for solid gear webs)

S t = σ F P = AGMA allowable bending fatigue strength S_t = \sigma_{FP} = \text{AGMA allowable bending fatigue strength} S t ​ = σ FP ​ = AGMA allowable bending fatigue strength

S F = Design safety factor against tooth bending breakage S_F = \text{Design safety factor against tooth bending breakage} S F ​ = Design safety factor against tooth bending breakage

4. AGMA Surface Pitting Fatigue / Contact Stress

Surface fatigue failure (macropitting) occurs when cyclic Hertzian contact stresses exceed the surface endurance limit of the tooth material: σ c = C p W t K o K v K s K m C f d P F I ≤ S c Z N C H S H Y θ Y Z \sigma_c = C_p \sqrt{W_t K_o K_v K_s \frac{K_m C_f}{d_P F I}} \le \frac{S_c Z_N C_H}{S_H Y_\theta Y_Z} σ c ​ = C p ​ W t ​ K o ​ K v ​ K s ​ d P ​ F I K m ​ C f ​ ​ ​ ≤ S H ​ Y θ ​ Y Z ​ S c ​ Z N ​ C H ​ ​

Where:

C p = Elastic Coefficient = 1 π ( 1 − ν P 2 E P + 1 − ν G 2 E G ) C_p = \text{Elastic Coefficient} = \sqrt{\frac{1}{\pi \left( \frac{1 - \nu_P^2}{E_P} + \frac{1 - \nu_G^2}{E_G} \right)}} C p ​ = Elastic Coefficient = π ( E P ​ 1 − ν P 2 ​ ​ + E G ​ 1 − ν G 2 ​ ​ ) 1 ​ ​ ( C p ≈ 2300 psi C_p \approx 2300\sqrt{\text{psi}} C p ​ ≈ 2300 psi ​ or 191 MPa 191\sqrt{\text{MPa}} 191 MPa ​ for steel-on-steel)

I = Surface Geometry Factor = sin ⁡ ϕ cos ⁡ ϕ 2 m N m G m G + 1 I = \text{Surface Geometry Factor} = \frac{\sin\phi \cos\phi}{2 m_N} \frac{m_G}{m_G + 1} I = Surface Geometry Factor = 2 m N ​ s i n ϕ c o s ϕ ​ m G ​ + 1 m G ​ ​ (for external spur gears)

d P = Pinion pitch diameter d_P = \text{Pinion pitch diameter} d P ​ = Pinion pitch diameter , F = Face width F = \text{Face width} F = Face width

C f = Surface condition factor (1.0) C_f = \text{Surface condition factor (1.0)} C f ​ = Surface condition factor (1.0)

S c = AGMA allowable contact fatigue strength S_c = \text{AGMA allowable contact fatigue strength} S c ​ = AGMA allowable contact fatigue strength

S H = Design safety factor against surface pitting S_H = \text{Design safety factor against surface pitting} S H ​ = Design safety factor against surface pitting

Note

Bending vs. Contact Stress Scaling: Bending stress scales linearly with load ( σ b ∝ W t \sigma_b \propto W_t σ b ​ ∝ W t ​ ), whereas contact stress scales with the square root of load ( σ c ∝ W t \sigma_c \propto \sqrt{W_t} σ c ​ ∝ W t ​ ​ ). Doubling transmitted torque doubles root bending stress ( + 100 % +100\% + 100% ), but increases contact stress by only 41.4 % 41.4\% 41.4% ( 2 = 1.414 \sqrt{2} = 1.414 2 ​ = 1.414 ). Surface pitting resistance almost universally governs steel gear sizing.

5. Gear Train Kinematics & Planetary Gear Trains +---------------------------------------------------------------------------------------------------+

  • | GEAR TRAIN CONFIGURATIONS |
  • | |
  • | SIMPLE TRAIN: COMPOUND TRAIN: PLANETARY (EPICYCLIC) TRAIN: |
  • | - One gear per shaft - Multiple gears per shaft - Sun (S), Planets (P), Ring (R) |
  • | - Idlers change direction - Velocity ratio multiplied - Carrier / Arm (C) rotates |
  • | - e = (-1)^k * (N_in/N_out) - e = (Prod N_in)/(Prod N_out)- Willis: (n_L - n_C)/(n_F - n_C) = e |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Simple and Compound Gear Trains

Simple Train: Idler gears between input and output reverse the direction of rotation but have zero effect on overall velocity ratio ( e = ( − 1 ) k N in N out e = (-1)^k \frac{N_{\text{in}}}{N_{\text{out}}} e = ( − 1 ) k N out ​ N in ​ ​ , where k k k is number of external meshes).

Compound Train: Multiple gears keyed to intermediate shafts multiply reductions: e = ω output ω input = ∏ Teeth on Driving Gears ∏ Teeth on Driven Gears e = \frac{\omega_{\text{output}}}{\omega_{\text{input}}} = \frac{\prod \text{Teeth on Driving Gears}}{\prod \text{Teeth on Driven Gears}} e = ω input ​ ω output ​ ​ = ∏ Teeth on Driven Gears ∏ Teeth on Driving Gears ​

2. Planetary (Epicyclic) Gear Trains

Planetary gearsets provide high reduction ratios in compact, coaxial packages. A standard planetary set comprises a central Sun gear ( S S S ) , multiple Planet gears ( P P P ) , an internal toothed Ring gear ( R R R ) , and a rotating Carrier/Arm ( C C C ) . +---------------------------------------------------------------------------------------------------+

  • | PLANETARY GEARSET COAXIAL GEOMETRY |
  • | |
  • | +-----------------------+ |
  • | / RING GEAR (R) \ |
  • | / +---------------+ \ |
  • | | / PLANET (P) \ | Geometric Pitch Rule: |
  • | | | (d_P, N_P) | | d_R = d_S + 2*d_P |
  • | | \ / | |
  • | | +---------------+ | Tooth Count Rule: |
  • | | / SUN (S) \ | N_R = N_S + 2*N_P |
  • | | | (d_S, N_S) | | |
  • | | \ / | (For module m = const) |
  • | \ +---------------+ / |
  • | \ / |
  • | +-----------------------+ |
  • +---------------------------------------------------------------------------------------------------+
  • The Willis Relative Velocity Equation

Fix the carrier in thought to determine the basic train value e train e_{\text{train}} e train ​ from first gear ( F F F ) to last gear ( L L L ): n L − n C n F − n C = e train \frac{n_L - n_C}{n_F - n_C} = e_{\text{train}} n F ​ − n C ​ n L ​ − n C ​ ​ = e train ​

Where n F n_F n F ​ , n L n_L n L ​ , and n C n_C n C ​ are rotational speeds of First gear, Last gear, and Carrier. With Sun as first gear and Ring as last gear: e train = − N S N R e_{\text{train}} = -\frac{N_S}{N_R} e train ​ = − N R ​ N S ​ ​ .

Standard Planetary Operational Modes

Fixed Element Input Element Output Element Overall Speed Ratio ( n in / n out n_{\text{in}} / n_{\text{out}} n in ​ / n out ​ ) Direction

Ring Gear ( n R = 0 n_R = 0 n R ​ = 0 ) Sun Gear ( S S S ) Carrier ( C C C ) 1 + N R N S 1 + \frac{N_R}{N_S} 1 + N S ​ N R ​ ​ Same as Input (Reduction)

Sun Gear ( n S = 0 n_S = 0 n S ​ = 0 ) Ring Gear ( R R R ) Carrier ( C C C ) 1 + N S N R = N R + N S N R 1 + \frac{N_S}{N_R} = \frac{N_R + N_S}{N_R} 1 + N R ​ N S ​ ​ = N R ​ N R ​ + N S ​ ​ Same as Input (Reduction)

Carrier ( n C = 0 n_C = 0 n C ​ = 0 ) Sun Gear ( S S S ) Ring Gear ( R R R ) − N R N S -\frac{N_R}{N_S} − N S ​ N R ​ ​ Opposite (Reverse Drive)

  • 6. Step-by-Step Worked Problem: Helical Gear Forces & Planetary Ratio
  • Problem Statement

A 20 ∘ 20^\circ 2 0 ∘ normal pressure angle ( ϕ n = 20 ∘ \phi_n = 20^\circ ϕ n ​ = 2 0 ∘ ) helical pinion with N P = 24 N_P = 24 N P ​ = 24 teeth, transverse diametral pitch P t = 6 in − 1 P_t = 6\text{ in}^{-1} P t ​ = 6 in − 1 , and right-hand helix angle ψ = 30 ∘ \psi = 30^\circ ψ = 3 0 ∘ transmits 30 hp 30\text{ hp} 30 hp at 1800 rpm 1800\text{ rpm} 1800 rpm to a driven gear. Determine pitch diameter d P d_P d P ​ , pitch line velocity V V V , tangential force W t W_t W t ​ , radial force W r W_r W r ​ , and axial thrust force W a W_a W a ​ .

A planetary gearset has a Sun gear with N S = 20 N_S = 20 N S ​ = 20 teeth and a Ring gear with N R = 80 N_R = 80 N R ​ = 80 teeth. If the Ring gear is fixed ( n R = 0 n_R = 0 n R ​ = 0 ) and the Sun rotates clockwise at 1500 rpm 1500\text{ rpm} 1500 rpm , compute the Carrier output speed n C n_C n C ​ and the number of teeth on each Planet gear N P N_P N P ​ .

  • Step-by-Step Solution
  • Part 1: Helical Gear Force Calculation

Pitch diameter: d P = N P P t = 24 6 = 4.0 inches d_P = \frac{N_P}{P_t} = \frac{24}{6} = 4.0\text{ inches} d P ​ = P t ​ N P ​ ​ = 6 24 ​ = 4.0 inches .

Pitch line velocity: V = π d P N P 12 = π ( 4.0 ) ( 1800 ) 12 = 1884.96 ft/min V = \frac{\pi d_P N_P}{12} = \frac{\pi (4.0)(1800)}{12} = 1884.96\text{ ft/min} V = 12 π d P ​ N P ​ ​ = 12 π ( 4.0 ) ( 1800 ) ​ = 1884.96 ft/min .

Transmitted tangential force: W t = 33000 P hp V = 33000 × 30 1884.96 = 525.2 lbf W_t = \frac{33000 P_{\text{hp}}}{V} = \frac{33000 \times 30}{1884.96} = 525.2\text{ lbf} W t ​ = V 33000 P hp ​ ​ = 1884.96 33000 × 30 ​ = 525.2 lbf .

Axial thrust force: W a = W t tan ⁡ ψ = 525.2 × tan ⁡ ( 30 ∘ ) = 525.2 × 0.57735 = 303.2 lbf W_a = W_t \tan\psi = 525.2 \times \tan(30^\circ) = 525.2 \times 0.57735 = 303.2\text{ lbf} W a ​ = W t ​ tan ψ = 525.2 × tan ( 3 0 ∘ ) = 525.2 × 0.57735 = 303.2 lbf .

Transverse pressure angle: tan ⁡ ϕ t = tan ⁡ ϕ n cos ⁡ ψ = tan ⁡ ( 20 ∘ ) cos ⁡ ( 30 ∘ ) = 0.36397 0.86603 = 0.42027 ⟹ ϕ t = 22.80 ∘ \tan\phi_t = \frac{\tan\phi_n}{\cos\psi} = \frac{\tan(20^\circ)}{\cos(30^\circ)} = \frac{0.36397}{0.86603} = 0.42027 \implies \phi_t = 22.80^\circ tan ϕ t ​ = c o s ψ t a n ϕ n ​ ​ = c o s ( 3 0 ∘ ) t a n ( 2 0 ∘ ) ​ = 0.86603 0.36397 ​ = 0.42027 ⟹ ϕ t ​ = 22.8 0 ∘ .

Radial separating force: W r = W t tan ⁡ ϕ t = 525.2 × 0.42027 = 220.7 lbf W_r = W_t \tan\phi_t = 525.2 \times 0.42027 = 220.7\text{ lbf} W r ​ = W t ​ tan ϕ t ​ = 525.2 × 0.42027 = 220.7 lbf .

Total resultant load: W = W t 2 + W r 2 + W a 2 = 525.2 2 + 220.7 2 + 303.2 2 = 645.4 lbf W = \sqrt{W_t^2 + W_r^2 + W_a^2} = \sqrt{525.2^2 + 220.7^2 + 303.2^2} = 645.4\text{ lbf} W = W t 2 ​ + W r 2 ​ + W a 2 ​ ​ = 525. 2 2 + 220. 7 2 + 303. 2 2 ​ = 645.4 lbf .

Part 2: Planetary Kinematics

Planet tooth count: N R = N S + 2 N P ⟹ 80 = 20 + 2 N P ⟹ 2 N P = 60 ⟹ N P = 30 teeth N_R = N_S + 2 N_P \implies 80 = 20 + 2 N_P \implies 2 N_P = 60 \implies \mathbf{N_P = 30\text{ teeth}} N R ​ = N S ​ + 2 N P ​ ⟹ 80 = 20 + 2 N P ​ ⟹ 2 N P ​ = 60 ⟹ N P ​ = 30 teeth .

Carrier speed using Willis formula (Sun = First, Ring = Last, e train = − N S N R = − 20 80 = − 0.25 e_{\text{train}} = -\frac{N_S}{N_R} = -\frac{20}{80} = -0.25 e train ​ = − N R ​ N S ​ ​ = − 80 20 ​ = − 0.25 ): n R − n C n S − n C = − 0.25 ⟹ 0 − n C 1500 − n C = − 0.25 \frac{n_R - n_C}{n_S - n_C} = -0.25 \implies \frac{0 - n_C}{1500 - n_C} = -0.25 n S ​ − n C ​ n R ​ − n C ​ ​ = − 0.25 ⟹ 1500 − n C ​ 0 − n C ​ ​ = − 0.25 − n C = − 0.25 ( 1500 − n C ) = − 375 + 0.25 n C ⟹ 1.25 n C = 375 -n_C = -0.25(1500 - n_C) = -375 + 0.25 n_C \implies 1.25 n_C = 375 − n C ​ = − 0.25 ( 1500 − n C ​ ) = − 375 + 0.25 n C ​ ⟹ 1.25 n C ​ = 375 n C = 375 1.25 = + 300 rpm (Clockwise) n_C = \frac{375}{1.25} = \mathbf{+300\text{ rpm (Clockwise)}} n C ​ = 1.25 375 ​ = + 300 rpm (Clockwise) (Ratio is 1 + N R N S = 1 + 80 20 = 5 : 1 1 + \frac{N_R}{N_S} = 1 + \frac{80}{20} = 5:1 1 + N S ​ N R ​ ​ = 1 + 20 80 ​ = 5 : 1 reduction) .

7. Exam Tips & Common Traps

Tip

Planetary Gear Shortcut: When the Ring gear is stationary ( n R = 0 n_R = 0 n R ​ = 0 ), the ratio from Sun to Carrier is always 1 + ( N R / N S ) 1 + (N_R / N_S) 1 + ( N R ​ / N S ​ ) . You can solve speed in 5 seconds without writing out the full Willis formula.

Warning

Common Traps to Avoid:

Normal vs Transverse Pitch: For helical gears, normal pitch P n P_n P n ​ is greater than transverse pitch P t P_t P t ​ ( P n = P t / cos ⁡ ψ P_n = P_t / \cos\psi P n ​ = P t ​ / cos ψ ). Pitch diameter is computed using transverse pitch ( d = N / P t d = N/P_t d = N / P t ​ ).

Worm Gear Efficiency Sign: Make sure to distinguish between driving through the worm vs backdriving through the gear. Worms with lead angle λ < tan ⁡ − 1 ( μ ) \lambda < \tan^{-1}(\mu) λ < tan − 1 ( μ ) cannot be backdriven.