Study guide

4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses

Key Takeaways Explain This Topic AI

The Extended Energy Equation balances pressure, kinetic, and potential energy heads while accounting for external pump addition ( + h p +h_p + h p ​ ), turbine extraction ( − h t -h_t − h t ​ ), and major/minor head losses ( − h L -h_L − h L ​ ).

Flow regime is dictated by the Reynolds number R e = ρ V D μ = V D ν Re = \frac{\rho V D}{\mu} = \frac{V D}{\nu} R e = μ ρ V D ​ = ν V D ​ ; laminar flow occurs at R e < 2300 Re < 2300 R e < 2300 where f = 64 R e f = \frac{64}{Re} f = R e 64 ​ , whereas turbulent flow ( R e > 4000 Re > 4000 R e > 4000 ) requires Colebrook or Swamee-Jain explicit equations.

Major friction loss in pipe flow is computed via the Darcy-Weisbach equation h f = f L D V 2 2 g h_f = f \frac{L}{D} \frac{V^2}{2g} h f ​ = f D L ​ 2 g V 2 ​ , which is dimensionally homogeneous and applicable to all fluids in both SI and US Customary units.

Minor losses across valves, fittings, contractions, and expansions are calculated via h m = K V 2 2 g h_m = K \frac{V^2}{2g} h m ​ = K 2 g V 2 ​ or by substituting equivalent length L e q = K D f L_{eq} = \frac{K D}{f} L e q ​ = f KD ​ into the Darcy equation.

In parallel piping networks, flow divides such that head loss across all branches is identical ( h L , 1 = h L , 2 = … h_{L,1} = h_{L,2} = \dots h L , 1 ​ = h L , 2 ​ = … ), while in looped networks the Hardy Cross method balances loop head losses ( ∑ h L = 0 \sum h_L = 0 ∑ h L ​ = 0 ) and node flows ( ∑ Q = 0 \sum Q = 0 ∑ Q = 0 ).

Last updated: August 2026

Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses

Internal flow in closed conduits forms the backbone of thermal-fluid engineering, encompassing chilled water loops, boiler feedwater circuits, oil transport pipelines, and industrial process piping. Mastering the extended energy equation , Darcy-Weisbach friction factor calculations , minor loss coefficients , and series/parallel network analysis ensures complete computational readiness for the NCEES PE Mechanical exam. +---------------------------------------------------------------------------------------------------+

  • | PIPE FLOW & ENERGY BALANCE ARCHITECTURE |
  • | |
  • | [CONSERVATION OF MASS] [EXTENDED ENERGY EQUATION] [HEAD LOSS MECHANISMS] |
  • | - Q = A_1*V_1 = A_2*V_2 - p1/\gamma + V1^2/2g + z1 + h_p - Major: Darcy-Weisbach |
  • | - \dot{m} = \rho*A*V = const = p2/\gamma + V2^2/2g + z2 + h_L - Minor: h_m = K * V^2/(2g) |
  • | | |
  • | v |
  • | [GRADE LINE PROFILES] |
  • | - EGL = p/\gamma + V^2/2g + z |
  • | - HGL = p/\gamma + z |
  • | - EGL - HGL = V^2 / (2g) |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Conservation of Mass, Continuity & Velocity Profiles

For steady 1D flow through a rigid conduit, conservation of mass requires the mass flow rate m ˙ \dot{m} m ˙ to remain constant across any cross-section: m ˙ = ∫ A ρ ( V ⋅ n ^ ) d A = ρ 1 A 1 V 1 = ρ 2 A 2 V 2 = constant \dot{m} = \int_A \rho (\mathbf{V} \cdot \hat{n}) \, dA = \rho_1 A_1 V_1 = \rho_2 A_2 V_2 = \text{constant} m ˙ = ∫ A ​ ρ ( V ⋅ n ^ ) d A = ρ 1 ​ A 1 ​ V 1 ​ = ρ 2 ​ A 2 ​ V 2 ​ = constant

For incompressible fluids ( ρ 1 = ρ 2 = const \rho_1 = \rho_2 = \text{const} ρ 1 ​ = ρ 2 ​ = const ), the volumetric flow rate Q Q Q is conserved: Q = A 1 V 1 = A 2 V 2 = π D 1 2 4 V 1 = π D 2 2 4 V 2 Q = A_1 V_1 = A_2 V_2 = \frac{\pi D_1^2}{4} V_1 = \frac{\pi D_2^2}{4} V_2 Q = A 1 ​ V 1 ​ = A 2 ​ V 2 ​ = 4 π D 1 2 ​ ​ V 1 ​ = 4 π D 2 2 ​ ​ V 2 ​ ⟹ V 2 V 1 = ( D 1 D 2 ) 2 \implies \frac{V_2}{V_1} = \left( \frac{D_1}{D_2} \right)^2 ⟹ V 1 ​ V 2 ​ ​ = ( D 2 ​ D 1 ​ ​ ) 2

Laminar vs. Turbulent Velocity Profiles

Laminar Pipe Flow ( R e < 2300 Re < 2300 R e < 2300 ): Parabolic Hagen-Poiseuille profile: u ( r ) = V max ⁡ [ 1 − ( r R ) 2 ] , V avg = V max ⁡ 2 u(r) = V_{\max} \left[ 1 - \left(\frac{r}{R}\right)^2 \right], \quad V_{\text{avg}} = \frac{V_{\max}}{2} u ( r ) = V m a x ​ [ 1 − ( R r ​ ) 2 ] , V avg ​ = 2 V m a x ​ ​

Turbulent Pipe Flow ( R e > 4000 Re > 4000 R e > 4000 ): Flatter, plug-like power-law profile (e.g., 1 / 7 th 1/7^{\text{th}} 1/ 7 th power law): u ( r ) = V max ⁡ ( 1 − r R ) 1 / n , V avg ≈ 2 n 2 ( n + 1 ) ( 2 n + 1 ) V max ⁡ ≈ 0.817 V max ⁡ ( for n = 7 ) u(r) = V_{\max} \left( 1 - \frac{r}{R} \right)^{1/n}, \quad V_{\text{avg}} \approx \frac{2 n^2}{(n+1)(2n+1)} V_{\max} \approx 0.817 V_{\max} \; (\text{for } n=7) u ( r ) = V m a x ​ ( 1 − R r ​ ) 1/ n , V avg ​ ≈ ( n + 1 ) ( 2 n + 1 ) 2 n 2 ​ V m a x ​ ≈ 0.817 V m a x ​ ( for n = 7 )

Kinetic Energy Correction Factor ( α \alpha α )

The kinetic energy flux per unit weight of fluid across a cross-section is α V avg 2 2 g \alpha \frac{V_{\text{avg}}^2}{2g} α 2 g V avg 2 ​ ​ , where α = 1 A ∫ A ( u V avg ) 3 d A \alpha = \frac{1}{A} \int_A \left( \frac{u}{V_{\text{avg}}} \right)^3 dA α = A 1 ​ ∫ A ​ ( V avg ​ u ​ ) 3 d A :

Laminar flow: α = 2.0 \alpha = 2.0 α = 2.0

Turbulent flow: α ≈ 1.02 to 1.08 ≈ 1.0 \alpha \approx 1.02 \text{ to } 1.08 \approx 1.0 α ≈ 1.02 to 1.08 ≈ 1.0 (standard engineering assumption)

2. The Extended Energy Equation, Bernoulli & Grade Lines

Integrating the First Law of Thermodynamics along a steady, incompressible streamline with mechanical energy additions and viscous dissipations yields the Extended Energy Equation (in head form, units of length: m \text{m} m or ft \text{ft} ft ): p 1 γ + α 1 V 1 2 2 g + z 1 + h p = p 2 γ + α 2 V 2 2 2 g + z 2 + h t + h L \frac{p_1}{\gamma} + \alpha_1 \frac{V_1^2}{2g} + z_1 + h_p = \frac{p_2}{\gamma} + \alpha_2 \frac{V_2^2}{2g} + z_2 + h_t + h_L γ p 1 ​ ​ + α 1 ​ 2 g V 1 2 ​ ​ + z 1 ​ + h p ​ = γ p 2 ​ ​ + α 2 ​ 2 g V 2 2 ​ ​ + z 2 ​ + h t ​ + h L ​

Where:

p γ = Pressure Head (height of static fluid column supported by local pressure) \frac{p}{\gamma} = \text{Pressure Head (height of static fluid column supported by local pressure)} γ p ​ = Pressure Head (height of static fluid column supported by local pressure)

V 2 2 g = Velocity (Dynamic) Head \frac{V^2}{2g} = \text{Velocity (Dynamic) Head} 2 g V 2 ​ = Velocity (Dynamic) Head

z = Elevation Head above an arbitrary horizontal datum z = \text{Elevation Head above an arbitrary horizontal datum} z = Elevation Head above an arbitrary horizontal datum

h p = Pump Head added to the fluid = W pump m ˙ g = P hyd γ Q h_p = \text{Pump Head added to the fluid } = \frac{W_{\text{pump}}}{\dot{m} g} = \frac{P_{\text{hyd}}}{\gamma Q} h p ​ = Pump Head added to the fluid = m ˙ g W pump ​ ​ = γ Q P hyd ​ ​

h t = Turbine Head extracted from the fluid = P turbine γ Q h_t = \text{Turbine Head extracted from the fluid } = \frac{P_{\text{turbine}}}{\gamma Q} h t ​ = Turbine Head extracted from the fluid = γ Q P turbine ​ ​

h L = Total Head Loss = ∑ h f (major friction) + ∑ h m (minor fittings) h_L = \text{Total Head Loss} = \sum h_f \text{ (major friction)} + \sum h_m \text{ (minor fittings)} h L ​ = Total Head Loss = ∑ h f ​ (major friction) + ∑ h m ​ (minor fittings) +---------------------------------------------------------------------------------------------------+

  • | HYDRAULIC GRADE LINE (HGL) VS. ENERGY GRADE LINE (EGL) |
  • | |
  • | Energy Grade Line (EGL): \text{EGL} = \frac{p}{\gamma} + \frac{V^2}{2g} + z |
  • | |
  • | Hydraulic Grade Line (HGL): \text{HGL} = \frac{p}{\gamma} + z |
  • | |
  • | Vertical Separation: \text{EGL} - \text{HGL} = \frac{V^2}{2g} |

+---------------------------------------------------------------------------------------------------+ Elevation

  • ^ [Reservoir 1]
  • | |~~~|
  • | +---+------------ (EGL) -----------------------\ (Pump Jump +h_p)
  • | \ +------- (EGL) -------\
  • | \ (HGL) \ (HGL) \
  • | +------------------------------------+ +--- [Reservoir 2]
  • | Pipe Centerline |~~~|
  • | +---+
  • +-------------------------------------------------------------------------------------------> Distance
  • Critical Grade Line Engineering Rules

Continuous Downward Slope: In a constant-diameter pipe without pumps, the EGL always slopes downward in the direction of flow at a rate equal to the hydraulic friction slope S f = h f L S_f = \frac{h_f}{L} S f ​ = L h f ​ ​ .

Pump & Turbine Discontinuities: Across a pump, both EGL and HGL jump upward abruptly by + h p +h_p + h p ​ . Across a turbine, both drop abruptly by − h t -h_t − h t ​ .

Sub-Atmospheric Pressure / Siphon Trap: If the HGL falls below the pipe centerline , the gauge pressure in the pipe is negative (vacuum, p < 0 psig p < 0\text{ psig} p < 0 psig ). If the absolute pressure drops to the liquid vapor pressure ( p abs ≤ p v p_{\text{abs}} \le p_v p abs ​ ≤ p v ​ ), cavitation and vapor-lock will rupture the liquid column.

3. Reynolds Number and Flow Regimes

The Reynolds number ( R e Re R e ) represents the ratio of dynamic inertial forces to viscous shear forces: R e = ρ V D μ = V D ν = 4 m ˙ π D μ = 4 Q π D ν Re = \frac{\rho V D}{\mu} = \frac{V D}{\nu} = \frac{4 \dot{m}}{\pi D \mu} = \frac{4 Q}{\pi D \nu} R e = μ ρ V D ​ = ν V D ​ = π D μ 4 m ˙ ​ = π D ν 4 Q ​ +---------------------------------------------------------------------------------------------------+

  • | PIPE FLOW REGIME THRESHOLDS |
  • | |
  • | Laminar Flow: Re < 2300 (Viscous damping dominates, smooth streamline paths) |
  • | Critical / Transition: 2300 <= Re <= 4000 (Intermittent turbulent bursts and instabilities) |
  • | Fully Turbulent Flow: Re > 4000 (Chaotic turbulent eddies dominate transport) |
  • +---------------------------------------------------------------------------------------------------+
  • Hydraulic Diameter for Non-Circular Conduits

For non-circular ducts (rectangular, annular, open channels), the characteristic dimension is the hydraulic diameter ( D h D_h D h ​ ) : D h = 4 A c P w D_h = \frac{4 A_c}{P_w} D h ​ = P w ​ 4 A c ​ ​

Where A c A_c A c ​ is the cross-sectional flow area and P w P_w P w ​ is the wetted perimeter.

Rectangular Duct ( a × b a \times b a × b ): D h = 4 ( a b ) 2 ( a + b ) = 2 a b a + b D_h = \frac{4 (a b)}{2 (a + b)} = \frac{2 a b}{a + b} D h ​ = 2 ( a + b ) 4 ( ab ) ​ = a + b 2 ab ​

Concentric Annular Duct ( D o , D i D_o, D_i D o ​ , D i ​ ): D h = 4 [ π 4 ( D o 2 − D i 2 ) ] π ( D o + D i ) = D o − D i D_h = \frac{4 [\frac{\pi}{4}(D_o^2 - D_i^2)]}{\pi (D_o + D_i)} = D_o - D_i D h ​ = π ( D o ​ + D i ​ ) 4 [ 4 π ​ ( D o 2 ​ − D i 2 ​ )] ​ = D o ​ − D i ​

4. Major Head Loss: Darcy-Weisbach & Friction Factors

The Darcy-Weisbach equation is the universally applicable standard for major friction head loss across all fluid types and regimes: h f = f L D V 2 2 g = f 8 L Q 2 π 2 g D 5 h_f = f \frac{L}{D} \frac{V^2}{2g} = f \frac{8 L Q^2}{\pi^2 g D^5} h f ​ = f D L ​ 2 g V 2 ​ = f π 2 g D 5 8 L Q 2 ​ Δ p f = ρ g h f = γ h f = f L D ( ρ V 2 2 ) \Delta p_f = \rho g h_f = \gamma h_f = f \frac{L}{D} \left( \frac{\rho V^2}{2} \right) Δ p f ​ = ρ g h f ​ = γ h f ​ = f D L ​ ( 2 ρ V 2 ​ )

Friction Factor ( f f f ) Determination +---------------------------------------------------------------------------------------------------+

  • | FRICTION FACTOR FORMULATION BY FLOW REGIME |
  • | |
  • | 1. LAMINAR REGIME (Re < 2300): |
  • | f = \frac{64}{Re} (Exact Hagen-Poiseuille analytic solution, independent of roughness \epsilon)|
  • | |
  • | 2. FULLY TURBULENT COLEBROOK EQUATION (Implicit, Moody Chart Baseline): |
  • | \frac{1}{\sqrt{f}} = -2.0 \log_{10} \left( \frac{\epsilon / D}{3.7} + \frac{2.51}{Re \sqrt{f}} \right) |
  • | |
  • | 3. SWAMEE-JAIN EXPLICIT EQUATION (Direct Evaluation, +/- 1% accuracy for Re in [4000, 10^8]): |

| f = \frac{0.25}{\left[ \log_{10} \left( \frac{\epsilon / D}{3.7} + \frac{5.74}{Re^{0.9}} \right) \right]^2} |

  • | |
  • | 4. FULLY ROUGH TURBULENT REGIME (Re -> \infty, f independent of Re): |

| \frac{1}{\sqrt{f}} = -2.0 \log_{10} \left( \frac{\epsilon / D}{3.7} \right) = 1.14 - 2.0 \log_{10}\left(\frac{\epsilon}{D}\right) |

  • +---------------------------------------------------------------------------------------------------+
  • Standard Absolute Pipe Roughness Values ( ϵ \epsilon ϵ )

Pipe Material Equivalent Roughness ϵ \epsilon ϵ (mm) Equivalent Roughness ϵ \epsilon ϵ (ft)

Drawn Tubing (Copper, Brass, Plastic/PVC) 0.0015 mm 0.0015\text{ mm} 0.0015 mm 5.0 × 10 − 6 ft 5.0 \times 10^{-6}\text{ ft} 5.0 × 1 0 − 6 ft

Commercial Steel / Wrought Iron 0.045 mm 0.045\text{ mm} 0.045 mm 1.5 × 10 − 4 ft 1.5 \times 10^{-4}\text{ ft} 1.5 × 1 0 − 4 ft

Galvanized Iron 0.150 mm 0.150\text{ mm} 0.150 mm 5.0 × 10 − 4 ft 5.0 \times 10^{-4}\text{ ft} 5.0 × 1 0 − 4 ft

Cast Iron (Uncoated) 0.260 mm 0.260\text{ mm} 0.260 mm 8.5 × 10 − 4 ft 8.5 \times 10^{-4}\text{ ft} 8.5 × 1 0 − 4 ft

Ductile Iron (Cement Mortar Lined) 0.025 mm 0.025\text{ mm} 0.025 mm 8.2 × 10 − 5 ft 8.2 \times 10^{-5}\text{ ft} 8.2 × 1 0 − 5 ft

Concrete (Smooth) 0.30 − 3.0 mm 0.30 - 3.0\text{ mm} 0.30 − 3.0 mm 1.0 × 10 − 3 − 1.0 × 10 − 2 ft 1.0 \times 10^{-3} - 1.0 \times 10^{-2}\text{ ft} 1.0 × 1 0 − 3 − 1.0 × 1 0 − 2 ft

5. Minor Losses (Loss Coefficients K K K & Equivalent Length L e q L_{eq} L e q ​ )

Turbulent flow separation, secondary swirling vortices, and boundary layer reattachment across valves, pipe entrances, bends, tees, and contractions cause localized dissipations called minor losses : h m = K V 2 2 g h_m = K \frac{V^2}{2g} h m ​ = K 2 g V 2 ​

Alternatively, minor loss can be expressed as an equivalent length ( L e q L_{eq} L e q ​ ) of straight pipe: h m = f L e q D V 2 2 g ⟹ K = f L e q D ⟹ L e q = K D f h_m = f \frac{L_{eq}}{D} \frac{V^2}{2g} \implies K = f \frac{L_{eq}}{D} \implies L_{eq} = \frac{K D}{f} h m ​ = f D L e q ​ ​ 2 g V 2 ​ ⟹ K = f D L e q ​ ​ ⟹ L e q ​ = f KD ​

Typical Minor Loss Coefficients ( K K K ) +---------------------------------------------------------------------------------------------------+

  • | REPRESENTATIVE MINOR LOSS VALUES (K) |
  • | |
  • | PIPE ENTRANCES: PIPE EXITS: |
  • | - Re-entrant (Borda): K = 0.78 - 1.0 - All exits into tank: K = 1.0 (Kinetic head lost) |
  • | - Sharp-edged: K = 0.50 |
  • | - Well-rounded (r/D>0.15): K = 0.04 VALVES (Fully Open): |
  • | - Globe valve: K = 10.0 |
  • | ELBOWS & BENDS: - Gate valve: K = 0.15 - 0.20 |
  • | - 90° Regular threaded: K = 0.90 - Ball valve: K = 0.05 |
  • | - 90° Long radius flanged: K = 0.30 - Swing check valve: K = 2.0 |
  • | - 45° Threaded: K = 0.40 - Angle valve: K = 5.0 |
  • +---------------------------------------------------------------------------------------------------+
  • Sudden Expansions and Contractions

Sudden Expansion (Borda-Carnot Formulation): K exp = ( 1 − A 1 A 2 ) 2 = [ 1 − ( D 1 D 2 ) 2 ] 2 K_{\text{exp}} = \left( 1 - \frac{A_1}{A_2} \right)^2 = \left[ 1 - \left(\frac{D_1}{D_2}\right)^2 \right]^2 K exp ​ = ( 1 − A 2 ​ A 1 ​ ​ ) 2 = [ 1 − ( D 2 ​ D 1 ​ ​ ) 2 ] 2 (Head loss is based on upstream velocity V 1 V_1 V 1 ​ : h m = K exp V 1 2 2 g h_m = K_{\text{exp}} \frac{V_1^2}{2g} h m ​ = K exp ​ 2 g V 1 2 ​ ​ )

Sudden Contraction: K con ≈ 0.5 ( 1 − A 2 A 1 ) K_{\text{con}} \approx 0.5 \left( 1 - \frac{A_2}{A_1} \right) K con ​ ≈ 0.5 ( 1 − A 1 ​ A 2 ​ ​ ) (Head loss is based on downstream velocity V 2 V_2 V 2 ​ : h m = K con V 2 2 2 g h_m = K_{\text{con}} \frac{V_2^2}{2g} h m ​ = K con ​ 2 g V 2 2 ​ ​ )

  • 6. Series and Parallel Piping Networks
  • Series Piping Systems

In a series pipe network, the conduits are connected end-to-end:

Continuity: Q = Q 1 = Q 2 = Q 3 = constant Q = Q_1 = Q_2 = Q_3 = \text{constant} Q = Q 1 ​ = Q 2 ​ = Q 3 ​ = constant

Total Head Loss: h L , total = ∑ h f , i + ∑ h m , i = ∑ ( f i L i D i + ∑ K i ) V i 2 2 g h_{L,\text{total}} = \sum h_{f,i} + \sum h_{m,i} = \sum \left( f_i \frac{L_i}{D_i} + \sum K_i \right) \frac{V_i^2}{2g} h L , total ​ = ∑ h f , i ​ + ∑ h m , i ​ = ∑ ( f i ​ D i ​ L i ​ ​ + ∑ K i ​ ) 2 g V i 2 ​ ​

Parallel Piping Systems

In a parallel configuration, the fluid branches at an upstream junction (node A A A ) and recombines at a downstream junction (node B B B ): +---------------------------------------------------------------------------------------------------+

  • | PARALLEL PIPING BRANCH ARCHITECTURE |
  • | |
  • | +-------- Branch 1 (L_1, D_1, f_1) --------+ |
  • | / \ |
  • | Flow Q_total ---> (A) (B) ---> Flow Q_total |
  • | \ / |
  • | +-------- Branch 2 (L_2, D_2, f_2) --------+ |
  • | |
  • | 1. Continuity: Q_total = Q_1 + Q_2 |
  • | 2. Energy Loss Balance: h_L1 = h_L2 = (p_A/\gamma + z_A) - (p_B/\gamma + z_B) |
  • +---------------------------------------------------------------------------------------------------+

Equating head loss expressions ( h L , 1 = h L , 2 h_{L,1} = h_{L,2} h L , 1 ​ = h L , 2 ​ ) neglecting minor losses: f 1 L 1 D 1 V 1 2 2 g = f 2 L 2 D 2 V 2 2 2 g ⟹ f 1 8 L 1 Q 1 2 π 2 g D 1 5 = f 2 8 L 2 Q 2 2 π 2 g D 2 5 f_1 \frac{L_1}{D_1} \frac{V_1^2}{2g} = f_2 \frac{L_2}{D_2} \frac{V_2^2}{2g} \implies f_1 \frac{8 L_1 Q_1^2}{\pi^2 g D_1^5} = f_2 \frac{8 L_2 Q_2^2}{\pi^2 g D_2^5} f 1 ​ D 1 ​ L 1 ​ ​ 2 g V 1 2 ​ ​ = f 2 ​ D 2 ​ L 2 ​ ​ 2 g V 2 2 ​ ​ ⟹ f 1 ​ π 2 g D 1 5 ​ 8 L 1 ​ Q 1 2 ​ ​ = f 2 ​ π 2 g D 2 5 ​ 8 L 2 ​ Q 2 2 ​ ​ ⟹ Q 1 Q 2 = f 2 f 1 ⋅ L 2 L 1 ⋅ ( D 1 D 2 ) 5 \implies \frac{Q_1}{Q_2} = \sqrt{\frac{f_2}{f_1} \cdot \frac{L_2}{L_1} \cdot \left(\frac{D_1}{D_2}\right)^5} ⟹ Q 2 ​ Q 1 ​ ​ = f 1 ​ f 2 ​ ​ ⋅ L 1 ​ L 2 ​ ​ ⋅ ( D 2 ​ D 1 ​ ​ ) 5 ​

Looped Networks & Hardy Cross Method Fundamentals

For complex closed-loop networks, the Hardy Cross method applies iterative corrections based on two governing laws:

Node Law: Flow into any node equals flow out: ∑ Q node = 0 \sum Q_{\text{node}} = 0 ∑ Q node ​ = 0 .

Loop Law: Algebraic sum of head losses around any closed loop must equal zero: ∑ loop h L = ∑ r Q ∣ Q ∣ n − 1 = 0 \sum_{\text{loop}} h_L = \sum r Q |Q|^{n-1} = 0 ∑ loop ​ h L ​ = ∑ r Q ∣ Q ∣ n − 1 = 0 (where h L = r Q 2 h_L = r Q^2 h L ​ = r Q 2 for Darcy-Weisbach).

In each iteration, the loop flow correction Δ Q \Delta Q Δ Q is computed as: Δ Q = − ∑ loop r Q 0 ∣ Q 0 ∣ 2 ∑ loop r ∣ Q 0 ∣ \Delta Q = -\frac{\sum_{\text{loop}} r Q_0 |Q_0|}{2 \sum_{\text{loop}} r |Q_0|} Δ Q = − 2 ∑ loop ​ r ∣ Q 0 ​ ∣ ∑ loop ​ r Q 0 ​ ∣ Q 0 ​ ∣ ​

  • 7. Step-by-Step Worked Engineering Problem
  • Problem Statement

Water at 20 ∘ C 20^\circ\text{C} 2 0 ∘ C ( ρ = 998 kg/m 3 , ν = 1.004 × 10 − 6 m 2 / s , γ = 9.79 kN/m 3 \rho = 998\text{ kg/m}^3, \nu = 1.004 \times 10^{-6}\text{ m}^2/\text{s}, \gamma = 9.79\text{ kN/m}^3 ρ = 998 kg/m 3 , ν = 1.004 × 1 0 − 6 m 2 / s , γ = 9.79 kN/m 3 ) is pumped from lower Reservoir 1 ( z 1 = 15.0 m z_1 = 15.0\text{ m} z 1 ​ = 15.0 m ) to upper Reservoir 2 ( z 2 = 45.0 m z_2 = 45.0\text{ m} z 2 ​ = 45.0 m ) at a flow rate of Q = 0.050 m 3 / s Q = 0.050\text{ m}^3/\text{s} Q = 0.050 m 3 / s ( 50 L/s 50\text{ L/s} 50 L/s ) through a commercial steel pipe ( ϵ = 0.045 mm \epsilon = 0.045\text{ mm} ϵ = 0.045 mm ) of inner diameter D = 150 mm D = 150\text{ mm} D = 150 mm ( 0.150 m 0.150\text{ m} 0.150 m ) and total length L = 200 m L = 200\text{ m} L = 200 m .

The piping system includes:

  • 1 sharp-edged entrance ( K ent = 0.50 K_{\text{ent}} = 0.50 K ent ​ = 0.50 )
  • 3 standard 90 ∘ 90^\circ 9 0 ∘ flanged elbows ( K elb = 0.30 K_{\text{elb}} = 0.30 K elb ​ = 0.30 each)
  • 1 fully open swing check valve ( K chk = 2.0 K_{\text{chk}} = 2.0 K chk ​ = 2.0 )
  • 1 fully open gate valve ( K gt = 0.20 K_{\text{gt}} = 0.20 K gt ​ = 0.20 )
  • 1 submerged pipe exit into Reservoir 2 ( K exit = 1.0 K_{\text{exit}} = 1.0 K exit ​ = 1.0 )

Determine:

The flow velocity V V V and Reynolds number R e Re R e .

The Darcy friction factor f f f and major head loss h f h_f h f ​ .

The total minor head loss h m h_m h m ​ .

The required pump head h p h_p h p ​ and the electrical power input to the pump motor assuming pump efficiency η p = 0.78 \eta_p = 0.78 η p ​ = 0.78 and motor efficiency η m = 0.92 \eta_m = 0.92 η m ​ = 0.92 . [Reservoir 1] [Reservoir 2]

  • |~~~| z_1 = 15.0 m |~~~| z_2 = 45.0 m
  • +---+ +---+
  • | (Sharp entrance) ^
  • v | (Submerged exit)
  • +------[ PUMP ]---------(Gate/Check Valves, 3 Elbows)-------------+
  • L = 200 m, D = 150 mm, Steel (\epsilon = 0.045 mm)
  • Step-by-Step Solution
  • Step 1: Calculate Velocity and Reynolds Number

Pipe area: A = π D 2 4 = π ( 0.150 ) 2 4 = 0.01767 m 2 A = \frac{\pi D^2}{4} = \frac{\pi (0.150)^2}{4} = 0.01767\text{ m}^2 A = 4 π D 2 ​ = 4 π ( 0.150 ) 2 ​ = 0.01767 m 2 .

Mean velocity: V = Q A = 0.050 m 3 / s 0.01767 m 2 = 2.830 m/s V = \frac{Q}{A} = \frac{0.050\text{ m}^3/\text{s}}{0.01767\text{ m}^2} = 2.830\text{ m/s} V = A Q ​ = 0.01767 m 2 0.050 m 3 / s ​ = 2.830 m/s .

Velocity head: V 2 2 g = ( 2.830 ) 2 2 × 9.81 = 8.009 19.62 = 0.4082 m \frac{V^2}{2g} = \frac{(2.830)^2}{2 \times 9.81} = \frac{8.009}{19.62} = 0.4082\text{ m} 2 g V 2 ​ = 2 × 9.81 ( 2.830 ) 2 ​ = 19.62 8.009 ​ = 0.4082 m .

Reynolds number: R e = V D ν = 2.830 × 0.150 1.004 × 10 − 6 = 4.228 × 10 5 ( Fully Turbulent ) Re = \frac{V D}{\nu} = \frac{2.830 \times 0.150}{1.004 \times 10^{-6}} = 4.228 \times 10^5 \quad (\text{Fully Turbulent}) R e = ν V D ​ = 1.004 × 1 0 − 6 2.830 × 0.150 ​ = 4.228 × 1 0 5 ( Fully Turbulent )

Step 2: Calculate Friction Factor and Major Head Loss

Relative roughness: ϵ D = 0.045 mm 150 mm = 0.000300 \frac{\epsilon}{D} = \frac{0.045\text{ mm}}{150\text{ mm}} = 0.000300 D ϵ ​ = 150 mm 0.045 mm ​ = 0.000300 .

Apply Swamee-Jain equation: f = 0.25 [ log ⁡ 10 ( 0.000300 3.7 + 5.74 ( 4.228 × 10 5 ) 0.9 ) ] 2 f = \frac{0.25}{\left[ \log_{10} \left( \frac{0.000300}{3.7} + \frac{5.74}{(4.228 \times 10^5)^{0.9}} \right) \right]^2} f = [ lo g 10 ​ ( 3.7 0.000300 ​ + ( 4.228 × 1 0 5 ) 0.9 5.74 ​ ) ] 2 0.25 ​ 0.000300 3.7 = 8.108 × 10 − 5 , 5.74 117 , 175 = 4.899 × 10 − 5 \frac{0.000300}{3.7} = 8.108 \times 10^{-5}, \quad \frac{5.74}{117,175} = 4.899 \times 10^{-5} 3.7 0.000300 ​ = 8.108 × 1 0 − 5 , 117 , 175 5.74 ​ = 4.899 × 1 0 − 5 Sum = 1.3007 × 10 − 4 ⟹ log ⁡ 10 ( 1.3007 × 10 − 4 ) = − 3.8858 \text{Sum} = 1.3007 \times 10^{-4} \implies \log_{10}(1.3007 \times 10^{-4}) = -3.8858 Sum = 1.3007 × 1 0 − 4 ⟹ lo g 10 ​ ( 1.3007 × 1 0 − 4 ) = − 3.8858 f = 0.25 ( − 3.8858 ) 2 = 0.25 15.100 = 0.01656 f = \frac{0.25}{(-3.8858)^2} = \frac{0.25}{15.100} = 0.01656 f = ( − 3.8858 ) 2 0.25 ​ = 15.100 0.25 ​ = 0.01656

Major friction loss: h f = f L D V 2 2 g = 0.01656 × ( 200 0.150 ) × 0.4082 m = 0.01656 × 1333.33 × 0.4082 = 9.012 m h_f = f \frac{L}{D} \frac{V^2}{2g} = 0.01656 \times \left(\frac{200}{0.150}\right) \times 0.4082\text{ m} = 0.01656 \times 1333.33 \times 0.4082 = 9.012\text{ m} h f ​ = f D L ​ 2 g V 2 ​ = 0.01656 × ( 0.150 200 ​ ) × 0.4082 m = 0.01656 × 1333.33 × 0.4082 = 9.012 m

Step 3: Calculate Minor Losses

Sum of minor loss coefficients: ∑ K = K ent + 3 ( K elb ) + K chk + K gt + K exit \sum K = K_{\text{ent}} + 3(K_{\text{elb}}) + K_{\text{chk}} + K_{\text{gt}} + K_{\text{exit}} ∑ K = K ent ​ + 3 ( K elb ​ ) + K chk ​ + K gt ​ + K exit ​ ∑ K = 0.50 + 3 ( 0.30 ) + 2.0 + 0.20 + 1.0 = 0.50 + 0.90 + 2.0 + 0.20 + 1.0 = 4.60 \sum K = 0.50 + 3(0.30) + 2.0 + 0.20 + 1.0 = 0.50 + 0.90 + 2.0 + 0.20 + 1.0 = 4.60 ∑ K = 0.50 + 3 ( 0.30 ) + 2.0 + 0.20 + 1.0 = 0.50 + 0.90 + 2.0 + 0.20 + 1.0 = 4.60

Minor head loss: h m = ( ∑ K ) V 2 2 g = 4.60 × 0.4082 m = 1.878 m h_m = \left( \sum K \right) \frac{V^2}{2g} = 4.60 \times 0.4082\text{ m} = 1.878\text{ m} h m ​ = ( ∑ K ) 2 g V 2 ​ = 4.60 × 0.4082 m = 1.878 m

Total head loss: h L = h f + h m = 9.012 + 1.878 = 10.89 m h_L = h_f + h_m = 9.012 + 1.878 = 10.89\text{ m} h L ​ = h f ​ + h m ​ = 9.012 + 1.878 = 10.89 m .

Step 4: Determine Required Pump Head and Electric Power

Applying Extended Energy Equation between free surfaces 1 and 2 ( p 1 = p 2 = 0 gauge p_1 = p_2 = 0\text{ gauge} p 1 ​ = p 2 ​ = 0 gauge , V 1 = V 2 ≈ 0 V_1 = V_2 \approx 0 V 1 ​ = V 2 ​ ≈ 0 ): z 1 + h p = z 2 + h L ⟹ h p = ( z 2 − z 1 ) + h L z_1 + h_p = z_2 + h_L \implies h_p = (z_2 - z_1) + h_L z 1 ​ + h p ​ = z 2 ​ + h L ​ ⟹ h p ​ = ( z 2 ​ − z 1 ​ ) + h L ​ h p = ( 45.0 − 15.0 ) + 10.89 m = 30.0 + 10.89 = 40.89 m h_p = (45.0 - 15.0) + 10.89\text{ m} = 30.0 + 10.89 = 40.89\text{ m} h p ​ = ( 45.0 − 15.0 ) + 10.89 m = 30.0 + 10.89 = 40.89 m

Hydraulic power: P hyd = γ Q h p = ( 9790 N/m 3 ) × ( 0.050 m 3 / s ) × ( 40.89 m ) = 20 , 016 W = 20.02 kW P_{\text{hyd}} = \gamma Q h_p = (9790\text{ N/m}^3) \times (0.050\text{ m}^3/\text{s}) \times (40.89\text{ m}) = 20,016\text{ W} = 20.02\text{ kW} P hyd ​ = γ Q h p ​ = ( 9790 N/m 3 ) × ( 0.050 m 3 / s ) × ( 40.89 m ) = 20 , 016 W = 20.02 kW

Electrical power input to motor: P elec = P hyd η p × η m = 20.016 kW 0.78 × 0.92 = 20.016 0.7176 = 27.89 kW P_{\text{elec}} = \frac{P_{\text{hyd}}}{\eta_p \times \eta_m} = \frac{20.016\text{ kW}}{0.78 \times 0.92} = \frac{20.016}{0.7176} = 27.89\text{ kW} P elec ​ = η p ​ × η m ​ P hyd ​ ​ = 0.78 × 0.92 20.016 kW ​ = 0.7176 20.016 ​ = 27.89 kW

8. Common Exam Traps & PE Pro-Tips

Tip

Quick Darcy vs. Hazen-Williams Head Loss Check: The Darcy-Weisbach equation applies to all fluids (water, oils, refrigerants, gases). Hazen-Williams ( h f = 4.73 L Q 1.852 / [ C 1.852 D 4.87 ] h_f = 4.73 L Q^{1.852} / [C^{1.852} D^{4.87}] h f ​ = 4.73 L Q 1.852 / [ C 1.852 D 4.87 ] ) is strictly empirical and valid only for liquid water at ambient temperatures ( 60 ∘ F 60^\circ\text{F} 6 0 ∘ F ) . If an exam problem specifies oil or chilled glycol, using Hazen-Williams is an immediate fatal error.

Warning

Common Traps to Avoid:

Trap 1 — Exit Loss Coefficient: The exit loss coefficient K exit K_{\text{exit}} K exit ​ into a reservoir is always 1.0 , regardless of whether the pipe end is sharp, flanged, or bell-mouthed, because the entire kinetic energy ( V 2 2 g \frac{V^2}{2g} 2 g V 2 ​ ) is dissipated into turbulent eddies inside the tank.

Trap 2 — Diameter Ratio Power in Parallel Flow: In parallel pipe flow, flow splits inversely with the square root of L L L and directly with D 5 / 2 = D 2.5 D^{5/2} = D^{2.5} D 5/2 = D 2.5 ( Q ∝ D 2.5 / f L Q \propto D^{2.5} / \sqrt{f L} Q ∝ D 2.5 / f L ​ ). A small increase in pipe diameter causes a massive increase in diverted flow.

Trap 3 — Units in Swamee-Jain: Ensure ϵ \epsilon ϵ and D D D have identical units when computing relative roughness ( ϵ / D \epsilon / D ϵ / D ). Mixing mm \text{mm} mm with m \text{m} m or inches \text{inches} inches with feet \text{feet} feet produces orders-of-magnitude errors.