Study guide

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy

PE Mechanical Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Reference Handbook & Mechanical Engineering Fundamentals

1.1 NCEES PE Mechanical CBT Format, Three Disciplines & Reference Handbook Strategy 1.2 Engineering Economics, Cash Flow & Project Evaluation and Scheduling 1.3 Units, Dimensional Analysis & Physical Constants 1.4 Statics, Dynamics & Mechanical Equilibrium

2 Chapter 2: Mechanical Design & Analysis (Stress, Failure Theories & Components)

2.1 Stress, Strain, Principal Stresses & Combined Loading 2.2 Static Failure Theories for Ductile and Brittle Materials 2.3 Fatigue Analysis, S-N Curves & Fluctuating Stresses 2.4 Pressure Vessels, Column Buckling & Spring Design 2.5 Threaded Fasteners, Welded Connections & Mechanical Joints

3 Chapter 3: Mechanical Power Transmission, Mechanisms & Vibrations

3.1 Shaft Sizing, Torsional Deflection & Critical Speeds 3.2 Spur, Helical, Bevel & Worm Gears and Epicyclic Gear Trains 3.3 Rolling-Element & Journal Bearings, Power Screws, Clutches, Brakes & Flywheels 3.4 Four-Bar Linkages, Cam-Follower Systems & Kinematics 3.5 Single-DOF and 2-DOF Vibrations, Damping & Dynamic Balancing

4 Chapter 4: Thermal & Fluid Systems

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy 4.2 Incompressible Pipe Flow, Darcy-Weisbach & Minor Losses 4.3 Pump Selection, System Curves, NPSH & Cavitation 4.4 Steady & Transient Conduction, Forced & Natural Convection 4.5 Radiation Heat Transfer, View Factors & Heat Exchanger Sizing (LMTD/NTU)

5 Chapter 5: Power Plants & Energy Conversion Systems

5.1 Thermodynamic Properties, Pure Substances & 1st/2nd Laws 5.2 Vapor Power Cycles (Rankine, Superheat, Reheat & Regeneration) 5.3 Gas Power Cycles (Brayton, Otto, Diesel, Dual & Combined Cycle) 5.4 Combustion Stoichiometry, Flue Gas Analysis & Thermochemistry 5.5 Turbomachinery, Compressible Flow & Nozzles, Renewables & Energy Storage

6 Chapter 6: HVAC & Refrigeration Systems

6.1 Psychrometric Principles & Air-Conditioning Processes 6.2 Cooling & Heating Load Calculations (CLTD/SCL/CLF & Heat Balance) 6.3 Vapor-Compression Refrigeration Cycles & Refrigerant Properties 6.4 Refrigeration Equipment (Compressors, Evaporators, Condensers, Expansion Devices) & Safety Codes 6.5 Air Distribution, Duct Design, Fans & Hydronic Water Networks 6.6 Energy Recovery Devices, HVAC Acoustics & Vibration Isolation

7 Chapter 7: Materials, Manufacturing & Processing

7.1 Ferrous/Non-Ferrous Metals, Polymers, Ceramics & Composites 7.2 Iron-Carbon Equilibrium Phase Diagram & Heat Treatment Processes 7.3 Corrosion, Wear, Creep, Hydrogen Embrittlement & Fracture Mechanics 7.4 Casting, Metal Forming, Forging, Stamping & Powder Metallurgy 7.5 Machining Dynamics, Tool Wear, Welding Metallurgy & Non-Destructive Examination (NDE)

8 Chapter 8: Measurements, Controls, Codes & Engineering Ethics

8.1 Temperature, Pressure, Flow & Strain Transducers and Signal Conditioning 8.2 Feedback Control Loops, PID Tuning, Frequency Response & Stability 8.3 ASME Boiler & Pressure Vessel Code, ASHRAE, OSHA & NFPA Safety Standards 8.4 NCEES Model Rules, Engineering Ethics & Professional Seal Liability

4.1 Fluid Statics, Manometry, Submerged Surfaces & Buoyancy

Key Takeaways Explain This Topic AI

Hydrostatic pressure increases linearly with depth in an incompressible fluid according to p = p 0 + ρ g h = p 0 + γ h p = p_0 + \rho g h = p_0 + \gamma h p = p 0 ​ + ρ g h = p 0 ​ + γh , acting perpendicularly to any submerged surface regardless of orientation.

Differential manometers are evaluated by writing continuous pressure balance equations along fluid columns, adding + γ Δ h +\gamma \Delta h + γ Δ h when moving downward and subtracting − γ Δ h -\gamma \Delta h − γ Δ h when moving upward.

The resultant hydrostatic force on any submerged plane surface is F R = p c A = γ h c A F_R = p_c A = \gamma h_c A F R ​ = p c ​ A = γ h c ​ A , acting not at the centroid y c y_c y c ​ , but at the deeper center of pressure y c p = y c + I x c y c A y_{cp} = y_c + \frac{I_{xc}}{y_c A} y c p ​ = y c ​ + y c ​ A I x c ​ ​ .

For submerged curved surfaces, horizontal force F H F_H F H ​ equals the hydrostatic force on the vertical projection of the surface, while vertical force F V F_V F V ​ equals the total weight of fluid contained directly above (or hypothetically above) the surface.

Rotational stability of a floating vessel is governed by the metacentric height G M = B M − B G = I w V disp − B G GM = BM - BG = \frac{I_w}{V_{\text{disp}}} - BG GM = BM − BG = V disp ​ I w ​ ​ − BG ; a positive G M > 0 GM > 0 GM > 0 ensures an upright restoring moment.

Last updated: August 2026

Fluid Statics, Manometry, Submerged Surfaces & Buoyancy

Fluid statics investigates fluids at rest where shear stresses are identically zero ( τ = 0 \tau = 0 τ = 0 ), leaving normal compressive stress—pressure ( p p p )—as the sole active surface force. Mastery of fluid properties, hydrostatic pressure distribution, multi-fluid manometer balancing, submerged plane and curved surface loading, and rotational buoyancy stability constitutes the cornerstone of thermal-fluid engineering on the NCEES PE Mechanical exam. +---------------------------------------------------------------------------------------------------+

  • | FLUID STATICS CORE ARCHITECTURE |
  • | |
  • | [FLUID PROPERTIES] [PRESSURE FIELDS] [SURFACE RESULTANTS] |
  • | - Density (\rho), \gamma - p = \rho*g*h = \gamma*h - Plane: F_R = \gamma * h_c * A |
  • | - Specific Gravity (SG) - Multi-fluid Manometry - Center of Pressure: y_cp |
  • | - Viscosity (\mu, \nu) - Absolute vs Gauge - Curved: F_H (proj) & F_V (weight) |
  • | | |
  • | v |
  • | [BUOYANCY & STABILITY] |
  • | - F_b = \gamma * V_disp |
  • | - Metacenter: GM = BM - BG |
  • | - BM = I_waterline / V_disp |
  • +---------------------------------------------------------------------------------------------------+
  • 1. Fluid Properties and Continuum Fundamentals

A fluid is a substance that deforms continuously under the application of a shear stress, no matter how small that shear stress may be.

Density, Specific Weight, and Specific Gravity

Mass Density ( ρ \rho ρ ): Mass per unit volume ( kg/m 3 \text{kg/m}^3 kg/m 3 in SI; slug/ft 3 \text{slug/ft}^3 slug/ft 3 or lbm/ft 3 \text{lbm/ft}^3 lbm/ft 3 in US Customary). For standard liquid water at 4 ∘ C 4^\circ\text{C} 4 ∘ C ( 39.2 ∘ F 39.2^\circ\text{F} 39. 2 ∘ F ): ρ water = 1000 kg/m 3 = 1.940 slugs/ft 3 = 62.43 lbm/ft 3 \rho_{\text{water}} = 1000\text{ kg/m}^3 = 1.940\text{ slugs/ft}^3 = 62.43\text{ lbm/ft}^3 ρ water ​ = 1000 kg/m 3 = 1.940 slugs/ft 3 = 62.43 lbm/ft 3

Specific Weight ( γ \gamma γ ): Gravitational weight per unit volume: γ = ρ g \gamma = \rho g γ = ρ g For standard water at 68 ∘ F 68^\circ\text{F} 6 8 ∘ F ( 20 ∘ C 20^\circ\text{C} 2 0 ∘ C ), γ water = 9.807 kN/m 3 = 62.4 lbf/ft 3 \gamma_{\text{water}} = 9.807\text{ kN/m}^3 = 62.4\text{ lbf/ft}^3 γ water ​ = 9.807 kN/m 3 = 62.4 lbf/ft 3 .

Specific Gravity ( S G SG SG ): Dimensionless ratio of fluid density to standard water density: S G = ρ ρ water, 4 ∘ C = γ γ water, 4 ∘ C SG = \frac{\rho}{\rho_{\text{water, } 4^\circ\text{C}}} = \frac{\gamma}{\gamma_{\text{water, } 4^\circ\text{C}}} SG = ρ water, 4 ∘ C ​ ρ ​ = γ water, 4 ∘ C ​ γ ​ ⟹ ρ = S G × ρ water , γ = S G × γ water \implies \rho = SG \times \rho_{\text{water}}, \quad \gamma = SG \times \gamma_{\text{water}} ⟹ ρ = SG × ρ water ​ , γ = SG × γ water ​

Viscosity: Dynamic and Kinematic

Shear stress in a Newtonian fluid in laminar shear flow is governed by Newton's Law of Viscosity : τ = μ d u d y \tau = \mu \frac{du}{dy} τ = μ d y d u ​

Where:

τ = Shear stress (Pa or lbf/ft 2 ) \tau = \text{Shear stress (Pa or } \text{lbf/ft}^2\text{)} τ = Shear stress (Pa or lbf/ft 2 )

μ = Dynamic (absolute) viscosity ( Pa ⋅ s = N ⋅ s/m 2 = kg/(m ⋅ s) in SI; lbf ⋅ s/ft 2 = slug/(ft ⋅ s) in US Customary ) \mu = \text{Dynamic (absolute) viscosity } (\text{Pa}\cdot\text{s} = \text{N}\cdot\text{s/m}^2 = \text{kg/(m}\cdot\text{s)} \text{ in SI; } \text{lbf}\cdot\text{s/ft}^2 = \text{slug/(ft}\cdot\text{s)} \text{ in US Customary}) μ = Dynamic (absolute) viscosity ( Pa ⋅ s = N ⋅ s/m 2 = kg/(m ⋅ s) in SI; lbf ⋅ s/ft 2 = slug/(ft ⋅ s) in US Customary )

d u d y = Velocity gradient or shear rate ( s − 1 ) \frac{du}{dy} = \text{Velocity gradient or shear rate } (\text{s}^{-1}) d y d u ​ = Velocity gradient or shear rate ( s − 1 ) +---------------------------------------------------------------------------------------------------+

  • | VISCOSITY CONVERSIONS & DEFINITIONS |
  • | |
  • | Kinematic Viscosity (\nu): \nu = \frac{\mu}{\rho} [\text{m}^2/\text{s} \text{ or } \text{ft}^2/\text{s}] |
  • | |
  • | Common Metric Units: 1 Poise (P) = 0.1 Pa·s = 100 Centipoise (cP) |
  • | 1 Stoke (St) = 10^-4 m^2/s = 100 Centistokes (cSt) |
  • | Water at 20°C: \mu \approx 1.0 cP = 1.002 \times 10^-3 Pa·s |
  • | \nu \approx 1.0 cSt = 1.004 \times 10^-6 m^2/s |
  • +---------------------------------------------------------------------------------------------------+
  • Bulk Modulus of Elasticity and Surface Tension

Bulk Modulus ( E v E_v E v ​ or K K K ): Quantifies fluid compressibility under isotropic hydrostatic pressure: E v = − v d P d v = ρ d P d ρ E_v = -v \frac{dP}{dv} = \rho \frac{dP}{d\rho} E v ​ = − v d v d P ​ = ρ d ρ d P ​ The speed of sound c c c in a liquid medium is directly related to bulk modulus: c = E v / ρ c = \sqrt{E_v / \rho} c = E v ​ / ρ ​ . For water, E v ≈ 2.2 GPa E_v \approx 2.2\text{ GPa} E v ​ ≈ 2.2 GPa ( 3.19 × 10 5 psi 3.19 \times 10^5\text{ psi} 3.19 × 1 0 5 psi ), confirming liquids are virtually incompressible under conventional engineering pressures.

Surface Tension ( σ \sigma σ ): Tensile force per unit length acting at liquid-gas or liquid-liquid interfaces ( N/m \text{N/m} N/m or lbf/ft \text{lbf/ft} lbf/ft ). Capillary height h h h in a circular tube of inner diameter d d d with contact angle θ \theta θ is: h = 4 σ cos ⁡ θ γ d h = \frac{4 \sigma \cos \theta}{\gamma d} h = γ d 4 σ cos θ ​

2. Hydrostatic Pressure Field and Absolute vs. Gauge Pressure

In a static fluid, the pressure gradient depends solely on the local body force of gravity: d p d z = − γ = − ρ g \frac{dp}{dz} = -\gamma = -\rho g d z d p ​ = − γ = − ρ g

Integrating for an incompressible fluid ( ρ = const \rho = \text{const} ρ = const ) from free surface elevation z 0 z_0 z 0 ​ where pressure is p 0 p_0 p 0 ​ down to elevation z z z at depth h = z 0 − z h = z_0 - z h = z 0 ​ − z : p ( h ) = p 0 + ρ g h = p 0 + γ h p(h) = p_0 + \rho g h = p_0 + \gamma h p ( h ) = p 0 ​ + ρ g h = p 0 ​ + γh +---------------------------------------------------------------------------------------------------+

  • | PRESSURE DATUM RELATIONSHIPS |
  • | |
  • | [Absolute Pressure (p_abs)] = [Gauge Pressure (p_gauge)] + [Atmospheric Pressure (p_atm)] |
  • | |
  • | [Vacuum Pressure (p_vac)] = [Atmospheric Pressure (p_atm)] - [Absolute Pressure (p_abs)] |
  • | |
  • | Standard Atmospheric Constants: |
  • | 1 atm = 101.325 kPa = 1.01325 bar = 14.696 psia = 2116.2 lbf/ft^2 |
  • | = 29.92 inHg = 760 mmHg = 33.91 ft of water = 10.33 m of water |
  • +---------------------------------------------------------------------------------------------------+

Important

Pressure Reference Rule: In hydrostatic force calculations and manometry, gauge pressures are standard because atmospheric pressure acts equally on both sides of structural boundaries (e.g., the dry face of a dam). However, in thermodynamic equations of state ( P = ρ R T P = \rho R T P = ρRT ) and cavitation calculations ( N P S H A NPSHA NPS H A ), you must always use absolute pressure .

3. Multi-Fluid Manometers and Differential Pressure Balancing

A manometer measures pressure differences across fluid columns using hydrostatic principles. The golden rule of manometer analysis is: Start at point 1 ⟶ Add ( + γ i h i ) when moving DOWN ⟶ Subtract ( − γ i h i ) when moving UP ⟶ Equate to point 2 \text{Start at point 1} \longrightarrow \text{Add } (+\gamma_i h_i) \text{ when moving DOWN} \longrightarrow \text{Subtract } (-\gamma_i h_i) \text{ when moving UP} \longrightarrow \text{Equate to point 2} Start at point 1 ⟶ Add ( + γ i ​ h i ​ ) when moving DOWN ⟶ Subtract ( − γ i ​ h i ​ ) when moving UP ⟶ Equate to point 2 +---------------------------------------------------------------------------------------------------+

  • | DIFFERENTIAL U-TUBE MANOMETER SCHEMATIC |
  • | |
  • | Pipe A (Fluid A, \gamma_A) Pipe B (Fluid B, \gamma_B) |
  • | (•) p_A (•) p_B |
  • | | | |
  • | | h_1 | h_3 |
  • | | | |
  • | +-----[Interface 1] | |
  • | \ | |
  • | \ Manometer Fluid (\gamma_m) +-----[Interface 2] |
  • | \ / |
  • | \ / h_2 (Deflection) |
  • | +---------------------------+ |
  • | (Datum Level) |
  • +---------------------------------------------------------------------------------------------------+
  • Equation Setup for Differential Manometer

Tracing the path from Pipe A to Pipe B: p A + γ A h 1 − γ m h 2 − γ B h 3 = p B p_A + \gamma_A h_1 - \gamma_m h_2 - \gamma_B h_3 = p_B p A ​ + γ A ​ h 1 ​ − γ m ​ h 2 ​ − γ B ​ h 3 ​ = p B ​ ⟹ p A − p B = γ m h 2 + γ B h 3 − γ A h 1 \implies p_A - p_B = \gamma_m h_2 + \gamma_B h_3 - \gamma_A h_1 ⟹ p A ​ − p B ​ = γ m ​ h 2 ​ + γ B ​ h 3 ​ − γ A ​ h 1 ​

Inclined Manometers for High Sensitivity

To measure tiny gas pressure differentials Δ p \Delta p Δ p , the manometer limb is inclined at an angle θ \theta θ to the horizontal. The scale reading L L L along the incline magnifies the vertical deflection h = L sin ⁡ θ h = L \sin \theta h = L sin θ : Δ p = γ m L sin ⁡ θ ⟹ L = Δ p γ m sin ⁡ θ \Delta p = \gamma_m L \sin \theta \implies L = \frac{\Delta p}{\gamma_m \sin \theta} Δ p = γ m ​ L sin θ ⟹ L = γ m ​ sin θ Δ p ​

4. Hydrostatic Forces on Submerged Plane Surfaces

When a planar surface of arbitrary geometry and area A A A is submerged in a liquid at an angle θ \theta θ relative to the free surface: +---------------------------------------------------------------------------------------------------+

  • | SUBMERGED PLANE SURFACE GEOMETRY & LOADING |
  • | |
  • | Free Surface ////////////////////////////////////////////////////// |
  • | \ |
  • | \ Angle \theta |
  • | \ |
  • | \ y_c (Distance along incline to Centroid C) |
  • | \-----------------------> [ CENTROID (C) ] Depth h_c = y_c * sin(\theta) |
  • | \ Pressure p_c = \gamma * h_c |
  • | \ y_cp (To Center of P) |
  • | \--------------------> [ CENTER OF PRESSURE (CP) ] |
  • | Line of Action for Total Force F_R |
  • +---------------------------------------------------------------------------------------------------+
  • Resultant Hydrostatic Force Magnitude

The total resultant force F R F_R F R ​ equals the pressure at the centroid multiplied by the total plate area: F R = ∫ A p d A = ∫ A ( γ y sin ⁡ θ ) d A = γ sin ⁡ θ ∫ A y d A = γ sin ⁡ θ ( y c A ) = p c A F_R = \int_A p \, dA = \int_A (\gamma y \sin \theta) \, dA = \gamma \sin \theta \int_A y \, dA = \gamma \sin \theta (y_c A) = p_c A F R ​ = ∫ A ​ p d A = ∫ A ​ ( γ y sin θ ) d A = γ sin θ ∫ A ​ y d A = γ sin θ ( y c ​ A ) = p c ​ A F R = γ h c A F_R = \gamma h_c A F R ​ = γ h c ​ A

Where:

h c = y c sin ⁡ θ = Vertical depth from free surface to the centroid of the area h_c = y_c \sin \theta = \text{Vertical depth from free surface to the centroid of the area} h c ​ = y c ​ sin θ = Vertical depth from free surface to the centroid of the area

  • A = Total submerged surface area A = \text{Total submerged surface area} A = Total submerged surface area
  • Center of Pressure Location ( y c p , x c p y_{cp}, x_{cp} y c p ​ , x c p ​ )

Because hydrostatic pressure increases linearly with depth, the pressure distribution is trapezoidal (or triangular). The resultant force acts below the centroid at the center of pressure ( x c p , y c p ) (x_{cp}, y_{cp}) ( x c p ​ , y c p ​ ) : y c p = y c + I x c y c A y_{cp} = y_c + \frac{I_{xc}}{y_c A} y c p ​ = y c ​ + y c ​ A I x c ​ ​ x c p = x c + I x y c y c A x_{cp} = x_c + \frac{I_{xyc}}{y_c A} x c p ​ = x c ​ + y c ​ A I x yc ​ ​

Where I x c I_{xc} I x c ​ is the area moment of inertia of the surface about its horizontal centroidal axis. For symmetric shapes, I x y c = 0 I_{xyc} = 0 I x yc ​ = 0 , so x c p = x c x_{cp} = x_c x c p ​ = x c ​ .

Standard Geometric Section Properties

  • Geometry Area ( A A A ) Centroid ( y c y_c y c ​ from base) Centroidal Inertia ( I x c I_{xc} I x c ​ )
  • Rectangle ( b × h b \times h b × h ) b h b h bh h / 2 h/2 h /2 b h 3 12 \frac{b h^3}{12} 12 b h 3 ​

Circle (Diameter D D D ) π D 2 4 \frac{\pi D^2}{4} 4 π D 2 ​ D / 2 D/2 D /2 π D 4 64 = π R 4 4 \frac{\pi D^4}{64} = \frac{\pi R^4}{4} 64 π D 4 ​ = 4 π R 4 ​

Semicircle (Radius R R R ) π R 2 2 \frac{\pi R^2}{2} 2 π R 2 ​ 4 R 3 π ≈ 0.4244 R \frac{4 R}{3 \pi} \approx 0.4244 R 3 π 4 R ​ ≈ 0.4244 R 0.1098 R 4 0.1098 R^4 0.1098 R 4

Triangle ( b × h b \times h b × h ) b h 2 \frac{b h}{2} 2 bh ​ h / 3 h/3 h /3 b h 3 36 \frac{b h^3}{36} 36 b h 3 ​

5. Hydrostatic Forces on Submerged Curved Surfaces

For curved surfaces, the pressure vectors vary continuously in direction across every differential element d A dA d A . Directly integrating vectors is avoided by resolving the total force into horizontal ( F H F_H F H ​ ) and vertical ( F V F_V F V ​ ) components. +---------------------------------------------------------------------------------------------------+

  • | FORCES ON SUBMERGED CURVED SURFACES |
  • | |
  • | Free Surface /////////////////////////////////////// |
  • | | | |
  • | | Fluid Volume (V) | |
  • | | Directly Above | |
  • | | Curved Surface AB | |
  • | | v |
  • | +=================( Surface AB ) |
  • | | <--- F_H / |
  • | | / F_R = \sqrt{F_H^2 + F_V^2} |
  • | v Projection A_v / |
  • | |
  • | 1. Horizontal Component F_H = Hydrostatic force on vertical projection A_v |
  • | 2. Vertical Component F_V = Total weight of fluid column situated above surface AB |
  • +---------------------------------------------------------------------------------------------------+
  • Formulation Matrix

Horizontal Force Component ( F H F_H F H ​ ): F H = γ h c , v A v F_H = \gamma h_{c,v} A_v F H ​ = γ h c , v ​ A v ​ Where A v A_v A v ​ is the area of the vertical projection of the curved surface, and h c , v h_{c,v} h c , v ​ is the depth to the centroid of this projected vertical plane. F H F_H F H ​ acts through the center of pressure of the vertical projection ( y c p , v = y c , v + I x c , v / ( y c , v A v ) y_{cp,v} = y_{c,v} + I_{xc,v}/(y_{c,v} A_v) y c p , v ​ = y c , v ​ + I x c , v ​ / ( y c , v ​ A v ​ ) ).

Vertical Force Component ( F V F_V F V ​ ): F V = γ V F_V = \gamma V F V ​ = γV Where V V V is the volume of the real (or imaginary) fluid column extending vertically from the curved surface up to the free surface plane. F V F_V F V ​ acts vertically downward (if fluid is above the surface) or upward (if fluid is below) through the centroid of the fluid volume V V V .

Resultant Force Magnitude and Direction: F R = F H 2 + F V 2 , θ = arctan ⁡ ( F V F H ) F_R = \sqrt{F_H^2 + F_V^2}, \quad \theta = \arctan\left(\frac{F_V}{F_H}\right) F R ​ = F H 2 ​ + F V 2 ​ ​ , θ = arctan ( F H ​ F V ​ ​ ) For circular-arc surfaces (e.g., Tainter radial gates), the local pressure vector on every surface element is normal to the boundary and thus passes through the center of curvature O O O . Therefore, the resultant force F R F_R F R ​ must pass directly through the arc's center of curvature .

  • 6. Archimedes' Principle, Buoyancy and Rotational Stability
  • Archimedes' Principle

Any body completely or partially submerged in a static fluid experiences an upward buoyant force F b F_b F b ​ equal to the weight of the fluid displaced by the body: F b = ρ f g V disp = γ f V disp F_b = \rho_f g V_{\text{disp}} = \gamma_f V_{\text{disp}} F b ​ = ρ f ​ g V disp ​ = γ f ​ V disp ​

The buoyant force acts vertically upward through the Center of Buoyancy ( B B B ) , which is the geometric centroid of the displaced fluid volume V disp V_{\text{disp}} V disp ​ .

The gravitational force W = m g = ρ body g V body W = m g = \rho_{\text{body}} g V_{\text{body}} W = m g = ρ body ​ g V body ​ acts vertically downward through the Center of Gravity ( G G G ) of the body. +---------------------------------------------------------------------------------------------------+

  • | STABILITY OF SUBMERGED VS. FLOATING BODIES |
  • | |
  • | SUBMERGED BODY STABILITY: FLOATING BODY ROTATIONAL STABILITY: |
  • | |
  • | - Stable: G is BELOW B - Metacenter M: Intersection of buoyant line |
  • | (Weight creates restoring couple) with centerline during tilt |
  • | - Unstable: G is ABOVE B - Metacentric Height: GM = BM - BG |
  • | (Weight creates overturning) - Metacentric Radius: BM = I_w / V_disp |
  • | - Neutral: G coincides with B - Stable: GM > 0 (M is ABOVE G) |
  • | - Neutral: GM = 0 (M coincides with G) |
  • | - Unstable: GM < 0 (M is BELOW G) |

+---------------------------------------------------------------------------------------------------+ Tilted Floating Hull Cross-Section:

  • CL
  • |
  • (M) Metacenter
  • / |
  • / | <--- Restoring Moment Arm: GZ = GM * sin(\theta)
  • / (G) Center of Gravity (Hull weight W)
  • / |
  • (B') ----+----(B) Original Center of Buoyancy
  • ^ |
  • | v
  • Buoyant Force F_b
  • Metacentric Height Calculation Formulation

Distance B G BG BG : Vertical distance from original center of buoyancy B B B to center of gravity G G G : B G = z G − z B BG = z_G - z_B BG = z G ​ − z B ​

Metacentric Radius ( B M BM BM ): B M = I w V disp BM = \frac{I_w}{V_{\text{disp}}} BM = V disp ​ I w ​ ​ Where I w I_w I w ​ is the second moment of area of the horizontal waterline cross-section about the longitudinal tilting axis (for a rectangular hull of length L L L and beam width b b b , I w = L b 3 12 I_w = \frac{L b^3}{12} I w ​ = 12 L b 3 ​ ).

Metacentric Height ( G M GM GM ): G M = B M − B G = I w V disp − ( z G − z B ) GM = BM - BG = \frac{I_w}{V_{\text{disp}}} - (z_G - z_B) GM = BM − BG = V disp ​ I w ​ ​ − ( z G ​ − z B ​ )

Righting Moment ( M R M_R M R ​ ): For small heel angles θ < 10 ∘ \theta < 10^\circ θ < 1 0 ∘ : M R = W ⋅ G M sin ⁡ θ = ( γ f V disp ) ⋅ G M sin ⁡ θ M_R = W \cdot GM \sin \theta = (\gamma_f V_{\text{disp}}) \cdot GM \sin \theta M R ​ = W ⋅ GM sin θ = ( γ f ​ V disp ​ ) ⋅ GM sin θ

  • 7. Step-by-Step Worked Engineering Problem
  • Problem Statement

A rectangular sluice gate of width w = 2.5 m w = 2.5\text{ m} w = 2.5 m (into the page) and inclined length L = 4.0 m L = 4.0\text{ m} L = 4.0 m is hinged at its top edge A A A , located at a vertical depth of 3.0 m 3.0\text{ m} 3.0 m below the free water surface. The gate is inclined at an angle of θ = 60 ∘ \theta = 60^\circ θ = 6 0 ∘ to the horizontal. Water density is ρ = 1000 kg/m 3 \rho = 1000\text{ kg/m}^3 ρ = 1000 kg/m 3 ( γ = 9.81 kN/m 3 \gamma = 9.81\text{ kN/m}^3 γ = 9.81 kN/m 3 ).

Determine:

The total resultant hydrostatic force F R F_R F R ​ acting on the gate.

The location of the center of pressure y c p y_{cp} y c p ​ along the incline from the free surface.

The horizontal clamping force F stop F_{\text{stop}} F stop ​ required at the bottom edge B B B to keep the gate closed. Free Surface //////////////////////////////////////////////

  • \
  • \ 3.0 m (Vertical to Hinge A)
  • \ y_A = 3.0 / sin(60°) = 3.464 m
  • (A) HINGE
  • \
  • \ L = 4.0 m, w = 2.5 m, \theta = 60°
  • \
  • \---- [ Centroid C: y_c = y_A + 2.0 m ]
  • \
  • \-- [ Center of Pressure CP: y_cp ]
  • \
  • (B) BOTTOM STOP (Horizontal Force F_stop)
  • Step-by-Step Solution
  • Step 1: Determine Coordinate Locations Along the Incline

Incline distance from surface datum to hinge A A A : y A = h A sin ⁡ θ = 3.0 m sin ⁡ 60 ∘ = 3.0 0.8660 = 3.4641 m y_A = \frac{h_A}{\sin \theta} = \frac{3.0\text{ m}}{\sin 60^\circ} = \frac{3.0}{0.8660} = 3.4641\text{ m} y A ​ = sin θ h A ​ ​ = sin 6 0 ∘ 3.0 m ​ = 0.8660 3.0 ​ = 3.4641 m

Distance along incline to centroid C C C (midpoint of gate L / 2 = 2.0 m L/2 = 2.0\text{ m} L /2 = 2.0 m ): y c = y A + L 2 = 3.4641 + 2.0000 = 5.4641 m y_c = y_A + \frac{L}{2} = 3.4641 + 2.0000 = 5.4641\text{ m} y c ​ = y A ​ + 2 L ​ = 3.4641 + 2.0000 = 5.4641 m

Vertical depth of centroid h c h_c h c ​ : h c = y c sin ⁡ 60 ∘ = 5.4641 × 0.8660 = 4.732 m h_c = y_c \sin 60^\circ = 5.4641 \times 0.8660 = 4.732\text{ m} h c ​ = y c ​ sin 6 0 ∘ = 5.4641 × 0.8660 = 4.732 m

Step 2: Calculate Resultant Hydrostatic Force ( F R F_R F R ​ )

Gate surface area A = w × L = 2.5 m × 4.0 m = 10.0 m 2 A = w \times L = 2.5\text{ m} \times 4.0\text{ m} = 10.0\text{ m}^2 A = w × L = 2.5 m × 4.0 m = 10.0 m 2 .

Total force: F R = γ h c A = ( 9810 N/m 3 ) × ( 4.732 m ) × ( 10.0 m 2 ) = 464 , 209 N = 464.2 kN F_R = \gamma h_c A = (9810\text{ N/m}^3) \times (4.732\text{ m}) \times (10.0\text{ m}^2) = 464,209\text{ N} = 464.2\text{ kN} F R ​ = γ h c ​ A = ( 9810 N/m 3 ) × ( 4.732 m ) × ( 10.0 m 2 ) = 464 , 209 N = 464.2 kN

Step 3: Calculate Center of Pressure ( y c p y_{cp} y c p ​ )

Centroidal moment of inertia for rectangle: I x c = w L 3 12 = 2.5 × ( 4.0 ) 3 12 = 160 12 = 13.333 m 4 I_{xc} = \frac{w L^3}{12} = \frac{2.5 \times (4.0)^3}{12} = \frac{160}{12} = 13.333\text{ m}^4 I x c ​ = 12 w L 3 ​ = 12 2.5 × ( 4.0 ) 3 ​ = 12 160 ​ = 13.333 m 4

Location along incline: y c p = y c + I x c y c A = 5.4641 + 13.333 5.4641 × 10.0 = 5.4641 + 0.2440 = 5.7081 m y_{cp} = y_c + \frac{I_{xc}}{y_c A} = 5.4641 + \frac{13.333}{5.4641 \times 10.0} = 5.4641 + 0.2440 = 5.7081\text{ m} y c p ​ = y c ​ + y c ​ A I x c ​ ​ = 5.4641 + 5.4641 × 10.0 13.333 ​ = 5.4641 + 0.2440 = 5.7081 m

Distance from hinge A A A to center of pressure: L c p = y c p − y A = 5.7081 − 3.4641 = 2.244 m L_{cp} = y_{cp} - y_A = 5.7081 - 3.4641 = 2.244\text{ m} L c p ​ = y c p ​ − y A ​ = 5.7081 − 3.4641 = 2.244 m

Step 4: Moment Equilibrium About Hinge A A A

Taking moments about hinge A A A ( ∑ M A = 0 \sum M_A = 0 ∑ M A ​ = 0 ):

Hydrostatic force acts perpendicularly to the gate at distance L c p = 2.244 m L_{cp} = 2.244\text{ m} L c p ​ = 2.244 m from hinge A A A .

Horizontal force F stop F_{\text{stop}} F stop ​ acts at bottom edge B B B (distance along gate is 4.0 m 4.0\text{ m} 4.0 m , vertical moment arm is 4.0 sin ⁡ 60 ∘ = 3.464 m 4.0 \sin 60^\circ = 3.464\text{ m} 4.0 sin 6 0 ∘ = 3.464 m ): ∑ M A = ( F R × L c p ) − ( F stop × L sin ⁡ 60 ∘ ) = 0 \sum M_A = (F_R \times L_{cp}) - (F_{\text{stop}} \times L \sin 60^\circ) = 0 ∑ M A ​ = ( F R ​ × L c p ​ ) − ( F stop ​ × L sin 6 0 ∘ ) = 0 ( 464.21 kN × 2.244 m ) − ( F stop × 4.0 m × 0.8660 ) = 0 (464.21\text{ kN} \times 2.244\text{ m}) - (F_{\text{stop}} \times 4.0\text{ m} \times 0.8660) = 0 ( 464.21 kN × 2.244 m ) − ( F stop ​ × 4.0 m × 0.8660 ) = 0 1041.69 kN ⋅ m = F stop × 3.4641 m 1041.69\text{ kN}\cdot\text{m} = F_{\text{stop}} \times 3.4641\text{ m} 1041.69 kN ⋅ m = F stop ​ × 3.4641 m F stop = 1041.69 3.4641 = 300.7 kN F_{\text{stop}} = \frac{1041.69}{3.4641} = 300.7\text{ kN} F stop ​ = 3.4641 1041.69 ​ = 300.7 kN

8. Common Exam Traps & PE Pro-Tips

Tip

Quick Check on Semicircular Surfaces: For a submerged vertical semicircular plate of radius R R R with its flat edge at the water surface, the centroid is located at h c = 4 R 3 π ≈ 0.4244 R h_c = \frac{4 R}{3 \pi} \approx 0.4244 R h c ​ = 3 π 4 R ​ ≈ 0.4244 R , and the center of pressure is exactly at h c p = 3 π 16 R ≈ 0.5890 R h_{cp} = \frac{3 \pi}{16} R \approx 0.5890 R h c p ​ = 16 3 π ​ R ≈ 0.5890 R .

Warning

Common Traps to Avoid:

Trap 1 — y c y_c y c ​ vs. h c h_c h c ​ Confusion: In F R = γ h c A F_R = \gamma h_c A F R ​ = γ h c ​ A , h c h_c h c ​ is the vertical depth . In the center of pressure formula y c p = y c + I x c / ( y c A ) y_{cp} = y_c + I_{xc}/(y_c A) y c p ​ = y c ​ + I x c ​ / ( y c ​ A ) , y c y_c y c ​ is the inclined distance from the surface line . Never plug vertical depth h c h_c h c ​ into the denominator of the y c p y_{cp} y c p ​ equation when θ ≠ 90 ∘ \theta \neq 90^\circ θ  = 9 0 ∘ !

Trap 2 — Imaginary Fluid Columns in Curved Surface Vertical Force: When liquid is situated below a curved boundary pushing upward, the vertical force F V F_V F V ​ equals the weight of the imaginary fluid column between the surface and the imaginary extension of the free liquid level, acting upward .

Trap 3 — Floating Stability Axis: In B M = I w / V disp BM = I_w / V_{\text{disp}} BM = I w ​ / V disp ​ , always calculate the moment of inertia I w I_w I w ​ about the axis that yields the smallest value (the longitudinal tilt axis, I = L b 3 / 12 I = L b^3 / 12 I = L b 3 /12 , using the smaller hull dimension b b b ).