Study guide
Combined Axial and Flexural Stress
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
Combined Axial and Flexural Stress
Key Takeaways Explain This Topic AI
Establish axial force and bending moments from equilibrium before combining their normal-stress contributions at a clearly identified point
For linear-elastic response, use signed superposition of N/A and bending terms about the actual centroidal axes
An eccentric axial force is statically equivalent to a centroidal axial force plus moment M = Pe
The kern identifies resultant locations that keep a linear-elastic section entirely in compression; outside the kern, a no-tension interface requires a different contact model
Evaluate biaxial stress at every candidate extreme point because the signs of both moment terms determine the governing corner
Do not substitute elastic stress addition for the strength interaction equations required by AISC 15th Edition or ACI 318-14
Last updated: July 2026
Combined Axial and Flexural Stress
For the July 2026 PE Civil: Structural exam, use the current NCEES PE Civil Reference Handbook , AISC Steel Construction Manual, 15th Edition (2017) , and ACI 318-14 when those materials govern. The handbook supplies mechanics relationships; the material standard supplies the applicable strength interaction. Those are related calculations, not interchangeable ones.
Build the elastic stress state
First find the section resultants from a free-body diagram. At a prismatic section under concentric axial force N and bending about one centroidal principal axis, linear-elastic normal stress is
σ = N/A ± Mc/I = N/A ± M/S .
This section takes tension as positive and compression as negative. The axial term is uniform. The bending term varies linearly with distance c from the neutral axis, is zero at that axis, and reaches its extreme magnitude at the farthest fiber. Do not add unsigned magnitudes automatically; identify the physical point and determine whether each contribution is tensile or compressive there.
- For biaxial bending about centroidal principal axes, a common signed form is
- σ(x,y) = N/A - Mx y/Ix + My x/Iy ,
subject to the declared moment and coordinate convention. If axes are not principal, a product-of-inertia term is involved; silently applying the principal-axis expression is then invalid. Evaluate the actual candidate corners. One corner can receive compression from both moments while another receives opposing contributions.
The formula assumes a linear strain distribution, elastic material response, and a section capable of carrying the calculated tension and compression. It describes demand at a point. Local stress concentrations, residual stress, cracking, yielding, and stability can require a different or additional model.
Eccentric force becomes force plus moment
A force P whose line of action is offset by perpendicular eccentricity e from the centroid is statically equivalent at the centroid to the same force plus
M = Pe .
Keep units compatible: kips times inches gives kip-inches. An eccentricity in two directions creates moments about both axes. The offset's sign determines which edge becomes more compressed; drawing the load line is safer than memorizing a plus sign.
Worked eccentric compression example
A rectangular section is 12 in wide and 18 in deep. A 180-kip compressive force acts 3 in from the centroid along the 18-in depth direction. Assume elastic behavior and bending about the width-parallel centroidal axis.
- A = 12(18) = 216 in²
- I = bh³/12 = 12(18³)/12 = 5,832 in⁴
- S = I/c = 5,832/9 = 648 in³
M = Pe = 180(3) = 540 kip-in .
The direct stress is -180/216 = -0.833 ksi . The extreme bending-stress magnitude is M/S = 540/648 = 0.833 ksi . At the near edge, bending adds compression, giving
σnear = -0.833 - 0.833 = -1.667 ksi .
At the far edge, bending opposes compression:
σfar = -0.833 + 0.833 = 0 ksi .
Force equilibrium is preserved because the bending-stress block has zero resultant, and moment equilibrium is preserved because it produces the 540 kip-in couple. Reporting only the maximum stress misses the equally important zero-stress edge.
Kern and no-tension behavior
The kern or core is the region through which a compressive resultant must pass for the linear-elastic stress distribution to remain compressive or zero everywhere. For uniaxial eccentricity about the depth of a rectangle, the kern limit is
|e| ≤ S/A = h/6 .
Here h/6 = 18/6 = 3 in , so the worked load lies exactly at the kern boundary and the far edge reaches zero. If |e| < 3 in , both edges remain compressed. If |e| > 3 in , elastic full-section superposition predicts tension at one edge.
That prediction does not mean every material actually carries that tension. Soil bearing interfaces, unbonded foundations, and some unreinforced materials may be modeled as no-tension contacts. Once separation occurs, the compression zone and neutral axis change; P/A ± M/S using the gross area is no longer the final contact distribution. Reinforced concrete can carry tension through reinforcement after concrete cracking, but ACI 318-14 section strength is evaluated by its code model, not by declaring the gross elastic tensile stress acceptable.
Elastic stress is not code interaction
A material-code interaction check compares required strengths with available strengths and incorporates behavior absent from simple elastic addition. For steel, the applicable AISC 15th Edition beam-column provisions use required axial and flexural strengths, available strengths for the chosen LRFD or ASD method, and the prescribed interaction equation. Stability, effective length or direct-analysis requirements, and second-order effects influence those quantities. A ratio such as Pr/Pc is not a stress at one corner.
For reinforced concrete, ACI 318-14 axial-flexural strength comes from strain compatibility, concrete compression behavior, reinforcement forces, nominal strength, and the applicable strength-reduction factor. A point on a Pn-Mn interaction diagram represents section capacity for a strain state; it is not produced by adding Pu/Ag to Mu/Sg .
Use one design framework consistently. Do not compare factored LRFD demand with ASD available strength or insert service-level elastic stress into a strength interaction equation. A good workflow is:
obtain N , Mx , and My from the correct load combination and analysis, including required second-order effects;
use elastic superposition when the question asks for stress, kern, or an elastic distribution;
use the exact AISC 15th or ACI 318-14 interaction procedure when the question asks for member or section strength;
confirm axes, signs, units, and the governing edge or interaction ratio.
This separation prevents an accurate mechanics calculation from becoming an invalid code check.