Study guide

Principal Stress, Mohr's Circle, and Combined Shear

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Principal Stress, Mohr's Circle, and Combined Shear

Key Takeaways Explain This Topic AI

Record the normal- and shear-stress sign convention on the element before using transformation equations or Mohr's circle

Principal stresses are the center of Mohr's circle plus or minus its radius, and shear stress is zero on principal planes

The physical principal-plane angle is one-half the corresponding Mohr-circle angle

Use a two-argument inverse tangent or an equivalent quadrant check when solving for 2 theta

Maximum in-plane shear equals the circle radius and acts with the average normal stress, not generally with zero normal stress

For plane stress, include the third principal stress of zero when a problem asks for absolute three-dimensional maximum shear

Last updated: July 2026

Principal Stress, Mohr's Circle, and Combined Shear

Use the plane-stress relationships in the current NCEES PE Civil Reference Handbook supplied for the July 2026 test date . Stress transformation is sensitive to conventions. Before calculating, sketch the stress element, label x and y , take tensile normal stress as positive, and state the shear convention used by the selected handbook equation. Mixing one source's shear arrows with another source's Mohr-circle plotting convention can preserve the stress magnitudes while reversing the reported angle.

The plane-stress state

At a point, plane stress is described by σx , σy , and τxy . For the equations below, positive τxy acts in the positive y direction on the positive x face and in the positive x direction on the positive y face. Let the x' axis be rotated counterclockwise by physical angle θ from x . Then

σx' = (σx + σy)/2 + [(σx - σy)/2]cos(2θ) + τxy sin(2θ)

τx'y' = -[(σx - σy)/2]sin(2θ) + τxy cos(2θ) .

The double angles arise from transforming an area orientation, not from a special material property. A plane physically rotated by θ corresponds to movement through 2θ around Mohr's circle. Depending on whether positive shear is plotted upward or downward, the plotted circle direction may oppose the physical rotation. State the convention rather than relying on visual memory.

A disciplined transformation workflow

A rotated stress element describes the same physical point under the same loading; only the faces used to report traction have changed. Use this sequence:

Draw positive faces and convert all stresses to one unit system. A negative normal value is compression under the tension-positive convention.

Identify whether the requested angle locates a plane , the plane's normal, or the rotated x' axis. A plane and its normal differ by 90 degrees.

Compute σavg and the half-difference (σx-σy)/2 before evaluating angles. These quantities expose many sign errors.

Use the full quadrant information for 2θ , then divide by two only once. List the perpendicular physical solution when orientation matters.

Substitute one candidate angle back into both transformation equations. Confirm the expected zero shear, maximum shear, or specified face stress.

The complementary shears on perpendicular faces have equal magnitude as required by moment equilibrium. The transformed normal stresses must sum to the original normal stresses, so σx' + σy' = σx + σy . If that trace changes, the transformation is inconsistent even if one ordinate looks reasonable.

  • Principal stresses and maximum shear
  • Define the circle center and radius as
  • C = σavg = (σx + σy)/2

R = sqrt{[(σx - σy)/2]^2 + τxy^2} .

  • The in-plane principal stresses are
  • σ1 = C + R and σ2 = C - R ,
  • ordered so σ1 ≥ σ2 . Shear is zero on principal planes. Their orientation satisfies

tan(2θp) = 2τxy/(σx - σy) .

A one-argument arctangent can return the wrong quadrant. Use an atan2 -style evaluation with numerator 2τxy and denominator σx - σy , or substitute the candidate angle back into the transformation equation and verify that τx'y' = 0 . The two principal planes are 90 degrees apart physically and therefore 180 degrees apart on Mohr's circle.

The maximum in-plane shear magnitude is R . Its planes are 45 degrees from the principal planes, and the accompanying normal stress is C . Maximum shear does not generally occur on a zero-normal-stress plane.

  • Worked combined stress state
  • At a point, let

σx = 80 MPa , σy = 20 MPa , and τxy = +30 MPa .

  • First compute
  • C = (80 + 20)/2 = 50 MPa
  • and
  • R = sqrt{[(80 - 20)/2]^2 + 30^2}

= sqrt(30^2 + 30^2) = 42.43 MPa .

  • Thus
  • σ1 = 50 + 42.43 = 92.43 MPa ,

σ2 = 50 - 42.43 = 7.57 MPa .

Both principal stresses are tensile, even though the original faces also carry shear. For orientation,

tan(2θp) = 2(30)/(80 - 20) = 1 .

The quadrant-consistent solution associated with σ1 is 2θp = 45° , so θp = 22.5° counterclockwise. Substitute it:

σx' = 50 + 30cos45° + 30sin45° = 92.43 MPa ,

τx'y' = -30sin45° + 30cos45° = 0 .

This check identifies the rotated x' face as the σ1 plane rather than the perpendicular σ2 plane. The maximum in-plane shear planes are at θs = 22.5° + 45° = 67.5° and the perpendicular orientation. Substitution gives shear magnitude 42.43 MPa and normal stress 50 MPa .

Construct and read Mohr's circle

Plot the two perpendicular-face states at opposite ends of a diameter, commonly A = (σx, τxy) and B = (σy, -τxy) under the chosen plotting convention. The center lies on the normal-stress axis at 50 MPa. The horizontal intercepts are 92.43 and 7.57 MPa; the top and bottom points carry shear magnitude 42.43 MPa.

Do not read a plotted 45-degree arc as a 45-degree physical rotation. It represents 2θ = 45° , or θ = 22.5° . Also distinguish a plane from its normal: some prompts ask for the plane orientation while others ask for the direction of the principal stress axis, which can shift the verbal angle by 90 degrees.

In-plane versus absolute maximum shear

A plane-stress problem has third principal stress σ3 = 0 in the out-of-plane direction. The absolute maximum shear in three dimensions is half the largest separation among all three principal stresses:

τabsolute,max = [max(σ1,σ2,0) - min(σ1,σ2,0)]/2 .

For the worked state, this is (92.43 - 0)/2 = 46.22 MPa , greater than the 42.43-MPa in-plane maximum. If σ1 and σ2 straddle zero, the in-plane radius may already be the absolute maximum. Read whether the question asks for maximum in-plane shear or absolute maximum shear.

Useful special cases provide quick checks. Equal biaxial normal stress with no shear gives a zero-radius circle. Pure shear, σx = σy = 0 , gives principal stresses +|τ| and -|τ| on planes rotated 45 degrees, while the maximum shear magnitude remains |τ| . Finally, transformed stresses must preserve the invariants σx' + σy' = σx + σy and the same Mohr-circle radius. These checks catch sign and angle errors before they propagate into a combined-stress decision.