Study guide

Snow, Rain, and Ice Loads

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Snow, Rain, and Ice Loads

Key Takeaways Explain This Topic AI

Convert mapped ground snow load to roof snow load with ASCE 7-16 exposure, thermal, importance, and roof-geometry provisions before checking local patterns

Balanced snow is only the starting case; drift, unbalanced, sliding, minimum, and rain-on-snow provisions can govern

IBC 2018 rain load assumes the primary drain is blocked and includes both static depth to the secondary inlet and hydraulic head above it

Ponding is a stiffness-feedback problem, so a simple undeflected-roof water weight does not complete the check for a susceptible bay

Atmospheric ice adds both ice weight and wind on an enlarged profile and uses ASCE 7-16's dedicated ice load combinations

  • Snow, rain, and atmospheric ice are distinct hazards and must not be collapsed into a single generic roof load
  • Last updated: July 2026

Snow, Rain, and Ice Loads

The NCEES topic names all three hazards, so a snow-only review is incomplete. For a July 2026 exam, use ASCE 7-16 Chapters 7, 8, and 10 with IBC 2018 Sections 1608, 1611, and 1614 .

Hazard Starting input Essential local check

Snow Mapped or approved ground snow load Roof shape, drift, unbalanced pattern, sliding, and applicable surcharges/minimums

Rain Water depth with primary drainage blocked Static head, hydraulic head, and ponding stability

Atmospheric ice Freezing-rain ice thickness and concurrent wind data Ice weight, enlarged projected area, partial loading, and dedicated combinations

Ground snow is not roof snow

Begin with ground snow load pg from the ASCE 7-16/IBC 2018 source or an approved site-specific study where required. The flat-roof snow load is

pf = 0.7 Ce Ct Is pg

where Ce represents exposure, Ct represents thermal condition, and Is is snow importance. These factors are not interchangeable: an exposed windswept roof, a continuously heated building, and a higher-risk occupancy affect different terms. For a sloped roof, apply the ASCE 7-16 roof-slope factor to obtain the balanced sloped-roof load, and check the prescribed minimum load where applicable.

Balanced load is only the baseline. Examine roof geometry for:

  • unbalanced loading on sloped, curved, folded, or multilevel roofs;
  • leeward drift at roof steps, projections, parapets, and adjacent taller structures;
  • sliding snow onto a lower roof;
  • local loads on roof equipment, pipes, and platforms; and

rain-on-snow surcharge where the ASCE 7-16 criteria apply.

A drift is not spread uniformly across the entire roof unless the prescribed geometry says so. Treat the drift surcharge as its specified distribution and place the pattern to maximize the response being checked.

  • Worked snow pattern
  • Suppose pg = 30 psf , and the problem gives Ce = Ct = Is = 1.0 . Then

pf = 0.7(1.0)(1.0)(1.0)(30) = 21 psf .

If the roof-slope factor provided for the roof is Cs = 0.90 , the balanced sloped-roof snow load is

ps = 0.90(21) = 18.9 psf .

Consider a supporting line with a 20-ft tributary width. Per foot along the support, balanced snow is 18.9(20) = 378 lb/ft . Now assume the required ASCE 7-16 drift calculation has produced a triangular surcharge with 22-psf peak over an 8-ft drift width. The added line load is the triangle's area:

(1/2)(8 ft)(22 psf) = 88 lb/ft .

For the same support, the patterned total is 378 + 88 = 466 lb/ft . A complete solution also checks the balanced case, required unbalanced cases, local shears and moments near the drift, and the applicable load combination.

Rain: assume the primary drain is blocked

IBC 2018 requires each roof portion to support water that accumulates when its primary drainage is blocked , plus water above the secondary-drain inlet needed to produce the design flow. In US customary units, the rain pressure is

R = 5.2(ds + dh) in psf,

where ds is the static depth on the undeflected roof up to the secondary inlet and dh is the hydraulic head above that inlet at design flow, both in inches.

For example, if ds = 1.5 in. and dh = 1.0 in. , then

R = 5.2(1.5 + 1.0) = 13.0 psf .

Over 200 ft², that is 13.0(200) = 2,600 lb , or 2.60 kip , on the undeflected-roof tributary area. Do not omit dh , and do not assume an operating primary drain eliminates the code case.

The pressure calculation is not the whole rain check. A flexible roof can deflect under water, creating a deeper basin that attracts more water, causing more deflection. IBC 2018 directs susceptible bays to the ASCE 7-16 ponding evaluation. Verify drainage geometry, stiffness, deflected behavior, secondary drainage, and controlled-drainage provisions as applicable.

Atmospheric ice is a separate structural condition

ASCE 7-16 Chapter 10 addresses atmospheric icing from freezing rain on ice-sensitive structures . Use the mapped nominal ice thickness and the standard's height, importance, and topographic provisions to obtain design ice thickness. Then determine both:

Di , the weight of ice attached to members, appurtenances, cables, or equipment; and

Wi , wind on the ice-covered structure using the enlarged projected dimensions and the Chapter 10 concurrent-wind procedure.

Do not use the full basic design wind event as though it automatically occurs with the design ice event. ASCE 7-16 supplies concurrent wind-on-ice requirements and dedicated strength and ASD ice combinations in Sections 2.3.3 and 2.4.3. Partial ice loading can also govern an asymmetric response.

As a geometry example, a circular member has bare diameter D = 4 in. and a code-derived radial design ice thickness t = 0.50 in. The iced diameter is D + 2t = 5 in. The annular ice area is

Ai = (π/4)(5^2 - 4^2) = 7.07 in² = 0.0491 ft² .

Using the ASCE 7-16 glaze-ice unit weight of 56 pcf gives an added ice line weight of about 56(0.0491) = 2.75 lb/ft . The projected width for wind rises from 4 to 5 in., a 25% increase before applying the appropriate force coefficient and concurrent velocity pressure. Ignoring either added weight or increased wind area misses part of the ice condition.

Combination and review discipline

For ordinary roof gravity combinations, follow the exact ASCE 7-16/IBC 2018 treatment of S and R ; do not automatically add full snow and full rain merely because both are water. Apply the separate rain-on-snow provision when triggered. For atmospheric ice, carry Di and Wi together through the dedicated ice combinations.

On the exam, finish with three questions: Did I convert the mapped hazard to the actual structural surface? Did I check the nonuniform or feedback case? Did I use the load combination written for this hazard in the 2016 standard? If all three answers are clear, snow, rain, and ice remain distinct and auditable.