Study guide
Fatigue and Progressive-Collapse Concepts
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
Fatigue and Progressive-Collapse Concepts
Key Takeaways Explain This Topic AI
Fatigue demand is governed primarily by repeated stress range and number of cycles, not simply by the largest algebraic stress
Connection geometry, weld profile, holes, attachments, and fabrication details determine fatigue category and crack sensitivity
A constant dead-load stress may shift mean stress without changing the calculated range between the same two cyclic extremes
Progressive-collapse robustness limits disproportionate spread after local damage through continuity, redundancy, ductility, and viable alternate load paths
No single progressive-collapse procedure governs every structure; use the applicable 2026 references, occupancy criteria, and project-specific requirements
Last updated: July 2026
Fatigue and Progressive-Collapse Concepts
Two different questions: Fatigue asks whether repeated stress fluctuations can initiate and grow a crack. Progressive-collapse assessment asks whether local damage can spread into failure that is disproportionate to the initiating event. Do not use one check as a substitute for the other.
Fatigue Starts With Stress Range
For one repeated cycle, calculate the signed extreme stresses at the same detail:
Δf = f_max - f_min .
If stress reverses from compression to tension, preserve signs before subtracting. A cycle from -5 ksi to +7 ksi has a 12-ksi range, not 2 ksi. Peak stress still matters for yielding and other limit states, but fatigue provisions commonly organize demand around stress range, number of repetitions, and detail category.
- Input What it represents Frequent error
- f_max, f_min Extremes at the same fatigue-sensitive point Comparing stresses from different locations
- Δf Fluctuation driving repeated crack growth Using only |f_max|
- n Expected cycles at a given range Counting years instead of load events
- Detail category Geometry/fabrication sensitivity Selecting by steel yield strength alone
Fatigue cracks tend to initiate at stress concentrations: weld toes and terminations, abrupt section changes, bolt holes, attachments, copes, and poor surface transitions. A higher-strength base metal does not automatically improve a fatigue-sensitive geometry. The applicable AASHTO or AISC detail description, loading direction, and fabrication condition control classification.
Worked Stress-Range and Cycle Screen
At a welded detail, constant dead load produces +8 ksi . A repeated vehicle event adds a cyclic stress varying from -6 ksi to +10 ksi . The total extremes are
- f_min = 8 - 6 = +2 ksi
- and
f_max = 8 + 10 = +18 ksi .
Therefore,
Δf = 18 - 2 = 16 ksi .
The constant 8-ksi component changes both total extremes but cancels from their difference. It cannot be ignored in a separate maximum-stress or strength check.
Suppose the event occurs 250 times per day for 40 years. The expected count is
n = 250(365)(40) = 3,650,000 cycles .
If the problem provides a 12-ksi permissible range for the identified category at that cycle count, the range ratio is
16/12 = 1.33 ,
so this illustrative screen does not pass. The 12-ksi value is problem-given, not a universal threshold. On a 2026 exam, retrieve the correct relationship from AASHTO LRFD 8th edition with its identified May 2018 errata or the AISC Steel Construction Manual, 15th edition, as applicable.
When several ranges occur, group cycles consistently with the required method. If a problem supplies fatigue lives N_i , a cumulative-damage check may use Σ(n_i/N_i) against its stated criterion. Do not average high and low ranges before verifying that the method permits it; a few large cycles can be disproportionately important.
A Fatigue Workflow
Identify the exact member location and potential crack plane.
Determine the current-code detail category from geometry, connection, and fabrication.
Calculate signed stress extremes from the same load event and point.
Find Δf ; separate constant stress from the fluctuating component.
Count cycles over the stated life and group variable amplitudes as required.
Compare demand with the category/cycle rule in the controlling 2026 reference.
Check other limit states independently and consider inspection access where required.
Progressive Collapse and Robustness
Progressive collapse is the spread of local damage through a structure, producing an extent of failure disproportionate to the initiating damage. Robustness is the ability to tolerate a local loss or abnormal condition without that disproportionate spread. Relevant attributes include:
- continuity: connections and ties can transfer forces after the original path changes;
- redundancy: more than one credible path can carry critical actions;
- ductility: components and connections can rotate or deform while retaining useful resistance;
- compartmentalization: deliberate boundaries can limit the region affected;
local resistance: selected critical elements may be designed for specified abnormal actions.
Redundancy is not merely counting members. Two nominal paths that rely on one brittle connection or the same vulnerable support are not independent. Ductile members do not create robustness if their connections fracture before rotations develop. Load reversal can also place tension where a gravity connection was detailed primarily for compression.
Alternate-Path Reasoning
When an applicable authority or project criterion requires a local-damage scenario, use this reasoning sequence:
Define the removed or impaired component and damage extent exactly as required.
Redraw the structure after damage; do not leave the lost reaction or member in the model.
Trace redistributed gravity and lateral actions through surviving members, connections, diaphragms, and foundations.
Apply the prescribed load combination, dynamic treatment, deformation limits, and acceptance criteria.
Check connection rotation, force reversal, stability, second-order effects, and whether supports can develop the alternate path.
Compare the predicted damaged region with the permitted extent and document weak links.
This is a framework, not a universal design equation. Requirements vary with structure, occupancy, risk, jurisdiction, and governing documents. For a 2026 PE Civil: Structural problem, use the supplied IBC 2018, AISC 15th, AASHTO 8th, and any explicit problem criteria; do not import a later edition or invent a single removal scenario for every building and bridge.
Final Distinction
A detail can have adequate monotonic strength yet poor fatigue performance, and a member can pass fatigue while the system lacks a viable alternate path. Keep the scales separate: fatigue follows local stress fluctuation through millions of events; robustness follows system redistribution after defined local damage.