Study guide

Reinforced Concrete Beams and Slabs

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Reinforced Concrete Beams and Slabs

Key Takeaways Explain This Topic AI

Effective depth d is measured from the compression face to the centroid of tension reinforcement, not to the member bottom or clear cover

Concrete flexural design requires nominal strength plus the correct strain-based strength-reduction context before comparison with factored demand

Passing flexure does not prove shear capacity, punching resistance, bar development, splice adequacy, or required reinforcement detailing

One-way and two-way slab behavior require different analysis and reinforcement distributions, including negative reinforcement over continuous supports

For a 2026 exam, use ACI 318-14 and the PE Civil handbook active for the test date rather than later concrete-code provisions

Last updated: July 2026

Reinforced Concrete Beams and Slabs

Strength is a gate, not the finish: A beam with φM_n ≥ M_u can still be unacceptable because of shear, development, splice, minimum reinforcement, spacing, cover, deflection, or constructability.

Geometry and the Compression Block

For a singly reinforced rectangular beam under positive bending, measure effective depth d from the extreme compression face to the centroid of the tension steel. Overall depth h , distance to the bar surface, and clear cover are different dimensions. If bars occur in multiple layers, locate their combined centroid.

  • Under the ACI 318-14 rectangular stress-block model, a common singly reinforced calculation is
  • a = A_s f_y/(0.85f'_c b)
  • and

M_n = A_s f_y(d - a/2) .

These equations do not decide the strength-reduction factor by themselves. Determine neutral-axis depth and tensile strain under the applicable ACI convention to establish whether the section is tension-controlled, in transition, or otherwise limited. Compression reinforcement in a doubly reinforced section requires strain compatibility and its actual stress; do not simply add A'_s f_y without checking whether it yields.

  • Check Required quantity Frequent mistake
  • Flexure M_u versus applicable φM_n Comparing M_u with nominal M_n
  • One-way shear V_u versus φ(V_c + V_s) Assuming stirrups are optional after flexure passes
  • Punching shear Two-way perimeter and slab/column geometry Using a beam-shear strip
  • Development Available length versus required anchorage Stopping bars at the theoretical moment cutoff
  • Worked Flexural Strength

A rectangular beam has b = 12 in , actual d = 21 in , A_s = 4.00 in² , f'_c = 4.0 ksi , and f_y = 60 ksi . Factored demand is M_u = 300 kip-ft . The problem states that the strain check qualifies for φ = 0.90 .

Compression-block depth is

a = 4.00(60)/[0.85(4.0)(12)] = 5.882 in .

  • Nominal moment strength is
  • M_n = 4.00(60)(21 - 5.882/2)

M_n = 4,334 kip-in = 361.2 kip-ft .

Design strength is

φM_n = 0.90(361.2) = 325.1 kip-ft .

The utilization is 300/325.1 = 0.923 , so flexural strength passes under the stated assumptions. Comparing 300 kip-ft directly with 361.2 kip-ft would skip φ . Using h instead of d would incorrectly enlarge the lever arm. The section still must satisfy ACI reinforcement limits and detailing.

Shear After Flexure

Concrete and transverse reinforcement contribute to nominal one-way shear resistance under the applicable ACI expressions. Use the critical section, effective depth, concrete density, longitudinal reinforcement, axial effects, and stirrup geometry required by the provision.

Suppose a separate problem-given shear check has V_u = 140 kips , calculated V_c = 120 kips , and φ_v = 0.75 . Required nominal stirrup contribution from equilibrium is at least

V_s ≥ V_u/φ_v - V_c

V_s ≥ 140/0.75 - 120 = 66.7 kips .

That result is only a required contribution. Select stirrup area, strength, legs, and spacing using ACI 318-14; then check minimum shear reinforcement, maximum spacing, maximum permitted strength, anchorage, and support regions. A calculated V_s = 0 would not automatically waive code minimums.

For slabs near columns, check two-way punching around the applicable critical perimeter. Openings, drop panels, column dimensions, edge/corner location, and unbalanced moment transfer can change demand and capacity. Beam one-way shear formulas are not a substitute.

Development, Splices, and Cutoffs

Flexural resistance exists only where reinforcement can develop the required stress. Development length depends on bar size, concrete strength, coating, top-bar condition, cover, spacing, confinement, and the applicable modification factors. Standard hooks, headed bars, or mechanical anchorage work only under their stated geometric and confinement conditions.

At a bar cutoff, extend reinforcement beyond the theoretical point as required and examine shear and crack implications. At supports, positive reinforcement may need continuity or anchorage for integrity and load reversal; negative bars require development into the support region. Lap-splice location, class, staggering, and confinement matter. Congested bars that cannot be placed with cover and spacing shown are not a valid detail.

Beam and Slab Behavior

A one-way slab primarily spans between two opposite support lines and can be analyzed as strips with actual continuity. A two-way slab distributes moment in two directions; use an ACI-permitted analysis method and distribute moment to the prescribed regions. Gravity loading typically produces bottom tension in positive midspan regions and top tension over continuous supports. Provide shrinkage-and-temperature reinforcement, edge/corner detailing, and support reinforcement as required rather than reinforcing only the largest positive strip moment.

Deflection checks may require immediate and long-term stiffness, cracking, sustained load, creep, shrinkage, and compression reinforcement. Strength-level M_u is not the service-load input for every deflection expression.

Complete ACI Workflow

Establish factored demands and service effects from the actual support/slab model.

Draw bars and calculate actual d ; identify singly or doubly reinforced behavior.

Calculate M_n , tensile strain, applicable φ , and reinforcement limits.

Check one-way shear and, for slabs, punching shear.

Develop every required bar and design splices, cutoffs, hooks, and support anchorage.

Check minimum reinforcement, cover, spacing, crack control, and service deflection.

Verify the load path through bearings, joints, columns, and walls.

Do not import a later ACI edition's equation or detailing rule into a 2026 solution.