Study guide

Earth Pressure and Surcharge Loads

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Earth Pressure and Surcharge Loads

Key Takeaways Explain This Topic AI

Select at-rest, active, or passive pressure from the wall's ability and direction of movement before choosing an earth-pressure coefficient

Compute soil effective-stress pressure and hydrostatic water pressure separately so saturated soil weight and water are not double-counted

A triangular lateral-pressure component acts at one-third its height above the base, while a uniform surcharge component acts at midheight

Uniform surcharge may create a rectangular Kq pressure, but strip, line, or localized surcharges require the applicable influence method

Passive resistance requires movement and reliable soil; it is not automatically available when excavation, scour, disturbance, or project criteria can remove it

Last updated: July 2026

Earth Pressure and Surcharge Loads

Sequence matters: Choose the pressure state from wall movement and boundary conditions first. Then compute effective soil pressure, surcharge pressure, and water pressure as separate components before summing forces and moments.

Choose the Pressure State

Lateral earth pressure is not a single material constant. The mobilized state depends on whether the wall can translate or rotate and in which direction. For simple cohesionless soil, K_p > K_0 > K_a ; use a coefficient consistent with the stated assumptions.

State Wall behavior Typical design situation Key caution

At-rest, K_0 Lateral strain is restrained Rigid basement wall tied to floors Do not assume active pressure merely because soil is behind a wall

Active, K_a Wall moves away enough to mobilize active conditions Yielding cantilever retaining wall Movement must be compatible with the assumed state

Passive, K_p Wall moves into soil enough to mobilize resistance Embedded toe or member resisting translation Required movement is larger and soil must remain available

Passive pressure is resistance, not a free stabilizing load. Do not credit it automatically if soil may be excavated, scoured, loosened, frozen, cyclically disturbed, or excluded by project criteria. Apply the specified reduction or safety treatment and verify that the structure can mobilize the required movement.

For a 2026 exam, use the PE Civil handbook active for the test date together with AASHTO 8th, including its May 2018 errata, and IBC 2018 where applicable. Do not import coefficients or provisions from the April 2027 standard set.

Build Pressure From Effective Stress

Let z increase downward. In a simple drained cohesionless case, lateral effective soil pressure is based on vertical effective stress:

p'_h(z) = K σ'_v(z) .

A uniform surface surcharge q often contributes a constant lateral increment Kq , producing a rectangular diagram over wall height H . Water produces hydrostatic pressure u = γ_w h_w , measured below the water surface. Total lateral pressure is assembled as

p_h = p'_h + Kq + u .

Below the water table, use submerged unit weight γ' = γ_sat - γ_w for the incremental soil effective stress and add hydrostatic water pressure separately. Using saturated total unit weight in the soil term and then adding full water pressure can count part of the water effect twice. Follow the stated drainage condition: a drain is not automatically reliable merely because a detail could contain one.

Useful resultants per unit length of wall are:

  • triangular pressure with base intensity p_b : P = ½p_bH , acting H/3 above the base;
  • uniform pressure p_u : P = p_uH , acting H/2 above the base;

hydrostatic pressure over water depth H_w : P_w = ½γ_wH_w² , acting H_w/3 above the bottom of that water wedge.

Worked Layered Wall Calculation

A 12-ft wall can yield enough for a problem-given K_a = 1/3 . The upper 6 ft has moist unit weight 120 pcf ; below the water table, the lower 6 ft has submerged unit weight 65 pcf . A uniform surcharge is q = 300 psf , and γ_w = 62.4 pcf . Calculate lateral thrust per foot of wall and its height above the base.

Decompose the effective soil diagram:

The upper soil creates pressure K_a(120)(6) = 240 psf at the water table. Its upper triangle is ½(240)(6) = 720 lb/ft , acting 8 ft above the base.

That 240-psf overburden remains through the lower 6 ft: 240(6) = 1,440 lb/ft , acting 3 ft above the base.

Lower submerged soil adds a triangle with base increment (1/3)(65)(6) = 130 psf : ½(130)(6) = 390 lb/ft , acting 2 ft above the base.

Uniform surcharge contributes (1/3)(300)(12) = 1,200 lb/ft , acting 6 ft above the base.

Water contributes ½(62.4)(6²) = 1,123.2 lb/ft , acting 2 ft above the base.

Total thrust is

P = 720 + 1,440 + 390 + 1,200 + 1,123.2 = 4,873.2 lb/ft = 4.873 kip/ft .

  • Moment about the base is
  • M = 720(8) + 1,440(3) + 390(2) + 1,200(6) + 1,123.2(2)

M = 20,306.4 lb-ft/ft .

Therefore the combined line of action is

ȳ = M/P = 20,306.4/4,873.2 = 4.17 ft above the base.

This calculation is correct only for the stated active condition and simplified soil profile. A restrained wall would require the appropriate at-rest coefficient, changing both soil and surcharge components.

Uniform Versus Localized Surcharge

A broad, uniform surcharge can justify the rectangular Kq increment under the applicable model. A strip footing, traffic lane, stockpile, or line load near the wall creates a depth-varying pressure that depends on width, setback, and geometry. Use the handbook or controlling standard's influence relationship; do not smear every localized load into a full-height Kq rectangle. For bridge abutments, preserve the AASHTO load model and location rules rather than substituting a building-code floor surcharge.

Complete Wall-Load Workflow

Sketch the wall, soil layers, water table, surcharge footprint, and possible excavation line.

Decide whether movement supports K_0 , K_a , or K_p ; document the assumption.

Build vertical effective stress layer by layer and convert it to lateral effective pressure.

Add uniform or localized surcharge using the correct model.

Add hydrostatic pressure unless the stated design condition legitimately removes it.

Convert each diagram to a resultant and moment; sum to find the combined line of action.

Check sliding, overturning, bearing, and structural actions with the required combinations, without automatically crediting passive resistance.

Keep pressure units ( psf or kPa ), resultant units per wall length ( lb/ft or kN/m ), and moment per wall length distinct. A correct coefficient cannot rescue a calculation that mixes those quantities.