Study guide

Vehicular, Crane, and Other Moving Loads

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Vehicular, Crane, and Other Moving Loads

Key Takeaways Explain This Topic AI

A moving load must be positioned to maximize the requested response; replacing it with a uniform load can miss the governing effect

Influence-line ordinates convert each axle or wheel load into a reaction, shear, or moment contribution at a chosen response location

A concentrated load is placed near a favorable influence-line peak, while a distributed lane load covers only the favorable region allowed by the load model

Crane runway checks must move the complete wheel arrangement and separately track vertical, lateral, and longitudinal actions through the load path

For 2026, use the PE Civil handbook active for the test date with AASHTO 8th, ASCE 7-16, and AISC 15th rather than future editions

Last updated: July 2026

Vehicular, Crane, and Other Moving Loads

Core idea: A moving load is defined by both magnitude and position. The same axle group can produce small, zero, or governing response as it travels, so calculate an envelope of possible effects rather than analyzing one convenient location.

Start With the Requested Response

A load position is only “critical” for a named response: left reaction, shear at a section, moment at a section, member force, or deflection. A position that maximizes midspan moment will not generally maximize support shear. For a linear structure, an influence line gives the response at the selected location caused by a unit load moving across the structure. Its ordinate may be positive, negative, or zero.

  • Moving load Placement principle Common mistake
  • Single wheel or axle Place near the largest favorable ordinate Automatically placing it at midspan
  • Fixed axle group Move the whole group without changing spacing Moving each axle independently

Uniform lane load Load the permitted favorable influence-line region Loading positive and negative regions together

Crane wheel group Preserve wheel spacing and trolley/bridge geometry Replacing all wheels with one centered resultant

  • For several concentrated loads, the response is
  • E = Σ(P_i y_i)

where P_i is a wheel or axle load and y_i is the influence ordinate under it. For a distributed load w , the contribution is w times the loaded area under the influence line. Apply only the load arrangements, lanes, presence factors, and simultaneous-loading rules required by the controlling reference.

Influence Line for a Beam-Section Moment

Consider a simply supported span L and a target section a from the left support. The moment influence ordinate for a unit load at coordinate x is

  • y_M = x(L - a)/L when 0 ≤ x ≤ a
  • y_M = a(L - x)/L when a ≤ x ≤ L

The two straight branches meet at x = a , where y_M = a(L - a)/L . The ordinate has units of length, so P y_M has moment units. This triangular influence line is positive across the span; an influence line for another response may change sign.

Worked axle-placement calculation

A 30-ft simple span has a target section 12 ft from the left. Two axles, 20 kips and 32 kips, are spaced 10 ft apart. Compare the event positions created when each axle reaches the target section.

At x = 12 ft , the peak ordinate is

y_M = 12(30 - 12)/30 = 7.2 ft .

Candidate A: Put the 32-kip axle at x = 12 ft ; the 20-kip axle is at x = 2 ft . Its ordinate is 2(18)/30 = 1.2 ft .

M_A = 32(7.2) + 20(1.2) = 254.4 kip-ft .

Candidate B: Put the 20-kip axle at x = 12 ft ; the 32-kip axle is at x = 22 ft . The latter ordinate is 12(30 - 22)/30 = 3.2 ft .

M_B = 20(7.2) + 32(3.2) = 246.4 kip-ft .

Candidate A governs these event positions. For a fixed group on a piecewise-linear influence line, also check entry/exit events and any other arrangement required by the load model. If a permitted 0.40 kip/ft lane load simultaneously covers the full positive span, its contribution is

0.40[½(30)(7.2)] = 43.2 kip-ft .

The combined effect would be 297.6 kip-ft only if the governing specification permits that axle-plus-lane combination. The mechanics calculation does not grant permission to combine loads.

Vehicular and Bridge Loads

For a 2026 exam, use the AASHTO LRFD Bridge Design Specifications, 8th edition, including the identified May 2018 errata and PE Exam Collection. Read the prescribed vehicle, lane occupancy, transverse placement, and combination provisions directly. Do not substitute an axle configuration from memory or a newer office edition. Create separate envelopes for positive moment, negative moment, shear, reaction, and fatigue response when the problem requires them. Dynamic allowance is a separate Chapter 4.2 decision and must be applied only where the governing provision directs.

Crane and Traveling-Equipment Loads

A crane produces a system of moving actions. The bridge travels along runway beams; the trolley moves across the bridge; lifted load location changes wheel reactions. A sound workflow is:

Position the trolley to maximize the near-side or far-side crane reaction.

Convert crane reactions into the specified runway wheel loads while preserving spacing.

Move the wheel group along the runway influence line.

Evaluate vertical response and the prescribed lateral and longitudinal actions separately.

Trace each action through rails, attachments, runway beams, columns, bracing, and foundations.

Apply the current ASCE 7-16/AISC 15th provisions and form the required load combinations.

Forklifts, erection equipment, gantries, and other traveling loads follow the same logic: preserve the real footprint, find favorable positions, and envelope the response. A uniform floor live load may be an additional case, but it is not automatically an equivalent substitute for concentrated moving wheels.

Exam Workflow

Write six labels before calculating: response, influence sign, load model, spacing, permitted concurrency, factors . Sketch the influence line, place concentrated loads at favorable ordinates, distribute lane load over allowed favorable regions, sum unamplified effects, then apply each prescribed factor once. Finally check units and whether the selected answer is a maximum positive effect, a maximum negative effect, or an absolute envelope.