Study guide
15.2 Structural and Cold-Formed Steel Properties
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
15.2 Structural and Cold-Formed Steel Properties
Key Takeaways Explain This Topic AI
Elastic modulus controls initial stiffness, while yield and ultimate strengths mark different stress levels; a higher-strength grade does not automatically have a higher modulus.
Hot-rolled shapes, plates, HSS, and built-up members have geometry, anisotropy, residual stress, and connection details that influence structural behavior beyond a coupon value.
Cold-formed members are thin sheet products shaped at ambient temperature and are especially sensitive to local, distortional, and global buckling modes.
Effective section properties can change as thin cold-formed elements buckle, so gross-area hot-rolled shortcuts are not automatically valid.
Residual stress and cold work affect yielding and stability but do not represent an external load or guarantee ductility.
Material properties, section properties, demand format, and the controlling limit state must remain distinct in every capacity calculation.
Last updated: July 2026
Steel is not defined by one strength number. Elastic stiffness, yielding, ultimate resistance, ductility, residual stress, geometry, and manufacturing route affect different responses. For July 2026, use the April 2024 PE Civil: Structural specification , current PE Civil Reference Handbook, and the AISC Steel Construction Manual 15th edition . Do not substitute the April 2027 standard set.
- Read the Stress-Strain Curve by Region
- In the initial linear-elastic range,
- σ = Eε
and common structural steels use approximately the same elastic modulus, about E = 29,000 ksi , even when their specified yield strengths differ. Raising F_y therefore increases an elastic load threshold but does not make a same-sized beam meaningfully stiffer before yield. Deflection and elastic buckling depend strongly on E and section properties, not simply F_y .
Yield strength F_y marks the onset or specified measure of significant permanent deformation. Ultimate tensile strength F_u is the maximum engineering tensile stress in a coupon test. They enter different limit states: gross-section yielding, net-section rupture, connection bearing, and weld or bolt checks do not all use the same property. Yield ratio and elongation provide additional behavior information, but neither alone is a complete ductility or toughness measure.
Nominal specified values are design inputs; mill certificates and coupon results are measured properties for particular material. A higher test value does not authorize an unreviewed substitution or a change to the specified design basis.
Hot-Rolled and Built-Up Structural Products
Wide-flange shapes, channels, angles, tees, bars, plates, and hollow structural sections place material differently around their centroid. Area governs uniform axial stress; I and section modulus govern elastic stiffness and stress; radius of gyration helps describe slenderness; torsion constant and warping properties govern twist. Always select the axis and property matching the response.
Rolling and welding leave self-equilibrating residual stresses. Although their net axial force over the section is zero, they cause parts of a compression member to yield earlier and influence buckling behavior. Welding can add a different residual-stress and distortion pattern. AISC member equations incorporate calibrated effects; do not add a guessed residual stress as an independent service load.
Built-up sections require transfer among components through welds, bolts, or other connectors. Two plates touching are not automatically one composite steel section. Holes reduce net area; shear lag can reduce effective net area; local load introduction can create yielding, crippling, or buckling not predicted by average P/A .
Worked Elastic Property Check
A 10 ft steel tension bar has area A = 2.00 in^2 , carries service axial load P = 72 kips , and has E = 29,000 ksi , specified F_y = 50 ksi , and F_u = 65 ksi . Find nominal axial stress, elastic strain, and elongation.
σ = P/A = 72/2.00 = 36.0 ksi
Because 36.0 < 50 ksi , the stated load remains below specified yield for this simple material check.
- ε = σ/E = 36/29,000 = 0.001241
- δ = εL = (0.001241)(120 in) = 0.149 in
This does not establish member adequacy: net area, connections, block shear, slenderness, load combinations, and design factors remain. If load increased to 110 kips, nominal stress would be 55 ksi—above F_y but below F_u . The elastic elongation formula would no longer describe the full response, and “below ultimate” would not make yielding acceptable.
Cold-Formed Steel Must Not Disappear
Cold-formed steel members are made by bending relatively thin sheet or strip at ambient temperature into studs, joists, tracks, deck, panels, lipped channels, and other shapes. Their high strength-to-weight ratio comes with slender plates and open-section behavior. Corners may gain strength from cold work, but property variation and reduced ductility can accompany that increase. Forming also creates residual stress.
Three instability scales are important:
Local buckling: a web, flange, or lip plate element buckles while fold lines remain substantially straight.
Distortional buckling: the cross-section changes shape, often involving flange-lip rotation and movement of fold lines.
Global buckling: the member bends or twists over its unbraced length.
Thin elements can carry post-buckling stress nonuniformly, leading to effective-width or effective-section concepts. Gross area and gross I may therefore differ from properties used for a particular strength calculation. Screw holes, web openings, concentrated bearing, web crippling, connection eccentricity, sheathing restraint, and corrosion loss can be proportionally significant.
The listed 2026 references support the exam's controlled workflow; do not import a future standard or apply a hot-rolled AISC capacity equation blindly to a cold-formed stud. When a problem supplies cold-formed section properties or an equation, use the supplied basis consistently. Concept questions often ask which mode or property changes, not a full specification design.
Property Workflow
Identify product and manufacturing route: rolled shape, plate, HSS, welded built-up member, or cold-formed sheet shape.
Separate E , F_y , F_u , ductility, and residual stress roles.
Use the correct gross, net, effective, or transformed section property.
Identify local, distortional, member, and connection limit states.
Match LRFD or ASD demand with its compatible resistance.
A final reasonableness check asks whether a changed variable affects stiffness, strength, or stability. Higher F_y changes strength; greater I changes stiffness and elastic buckling; shorter unbraced length changes global stability. They are not interchangeable improvements.