Study guide
Axial Tension, Compression, and Deformation
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
Axial Tension, Compression, and Deformation
Key Takeaways Explain This Topic AI
Use equilibrium to determine internal axial force before using stress or deformation equations
For a prismatic linear-elastic segment, sigma = N/A and delta = NL/(AE), with tension and elongation positive and compression and shortening negative
Add signed deformations segment by segment when force, area, modulus, or temperature changes
Keep force, length, area, and modulus units compatible; ksi with kips and square inches requires lengths in inches
Uniform temperature change causes free deformation without stress when movement is unrestrained, but restraint converts prevented thermal strain into force
For constrained axial systems, combine mechanical deformation, thermal deformation, support movement, and compatibility in one equation
Last updated: July 2026
Axial Tension, Compression, and Deformation
For July 2026 preparation, use the axial mechanics relationships in the current NCEES PE Civil Reference Handbook supplied for the test date . This section treats basic linear-elastic response; code member strength, connection design, and compression buckling are separate checks. An axial stress below yield does not prove that a slender compression member is stable.
Equilibrium first, constitutive law second
Cut the member perpendicular to its longitudinal axis and use equilibrium to find internal axial force N . This section takes tension as positive and compression as negative. The average normal stress in a concentric prismatic segment is
σ = N/A .
For linear-elastic material, σ = Eε , and axial strain is ε = δ/L . Combining them gives
δ = NL/(AE) .
With the stated sign convention, tensile N produces positive elongation and compressive N produces negative shortening. If a concentrated axial load occurs between two cuts, the axial-force diagram jumps by that load. If distributed axial load acts along the member, N varies with position. Never use the end load automatically for every segment; isolate each region.
The formula assumes the force is concentric, stress is represented adequately by its average away from local disturbances, material is linearly elastic, and deformation is small. Eccentric loading adds bending and belongs in combined-stress analysis. Near holes, connections, or abrupt changes, local stress concentration may make N/A insufficient for detailed design even though it remains useful for basic equilibrium.
Unit discipline
When N is in kips, A is in square inches, and E is in ksi ( kip/in² ), length must be in inches and the calculated deformation is in inches. Mixing a length in feet with E in ksi makes the answer wrong by a factor of 12. Stress has force-per-area units; strain is dimensionless; deformation has length units. In SI calculations, using newtons, square millimeters, megapascals ( N/mm² ), and millimeters is similarly self-consistent. Convert temperature units consistently with α ; a coefficient per degree Fahrenheit cannot multiply a Celsius temperature change without conversion.
Stepped and nonuniform members
Divide a stepped member wherever N , A , E , or thermal condition changes. For discrete prismatic segments in series,
δtotal = Σ Ni Li/(Ai Ei) .
Retain the sign of every Ni . For continuously varying properties, the corresponding form is δ = ∫ N(x)/[A(x)E(x)] dx . Members in series carry forces established by joint equilibrium; members in parallel generally share force according to stiffness and must satisfy compatible end deformation. Do not assume equal force or equal stress without checking the actual arrangement.
Worked stepped tension member
A two-segment steel bar carries a concentric 60-kip tensile force. Segment 1 has L1 = 8 ft = 96 in and A1 = 2.0 in² . Segment 2 has L2 = 6 ft = 72 in and A2 = 1.5 in² . Take E = 29,000 ksi . Because there is no axial load at the step, equilibrium gives N1 = N2 = +60 kip .
The stresses are
σ1 = 60/2.0 = 30 ksi , and σ2 = 60/1.5 = 40 ksi .
- The segment elongations are
- δ1 = 60(96)/[2.0(29,000)] = 0.0993 in ,
δ2 = 60(72)/[1.5(29,000)] = 0.0993 in .
Thus δtotal = 0.1986 in . The equal elongations are coincidental: segment 2 is shorter but also smaller. If the 60-kip force were compressive and buckling were set aside, the stresses and deformations would have the same magnitudes with negative signs. A compatibility question might prescribe total movement and require solving for the unknown force instead.
- Temperature: free movement versus restraint
- For a uniform temperature change ΔT , free thermal strain is
- εT = αΔT ,
and free deformation is δT = αΔT L , where α is the coefficient of thermal expansion. Heating gives positive expansion when α is positive. A freely moving member develops this deformation with no thermal stress . Temperature alone does not imply force.
Restraint changes the problem. Mechanical and thermal strains superpose in the linear range:
εtotal = σ/E + αΔT .
If rigid supports fully prevent the end-to-end movement of a uniformly heated bar, εtotal = 0 , so
σ = -EαΔT .
The negative sign means compression. Cooling under full restraint produces tension. The corresponding force is N = σA .
Worked fully restrained bar
A 20-ft steel bar has A = 4.0 in² , E = 29,000 ksi , α = 6.5 × 10^-6/°F , and a uniform temperature rise of 80°F . If free, it would expand
δT = (6.5 × 10^-6)(80)(240) = 0.1248 in .
- With ideal rigid supports and full restraint,
- σ = -29,000(6.5 × 10^-6)(80) = -15.08 ksi ,
and N = -15.08(4.0) = -60.3 kip . The stress expression does not contain length because both free expansion and mechanical shortening scale with length. Length still controls the prevented displacement.
Real supports may deform, a gap may close before restraint begins, or connected members may have different temperatures. Then write one compatibility equation rather than using -EαΔT blindly:
Σ[NiLi/(AiEi)] + Σ(αiΔTiLi) = prescribed support movement .
Include signs for support settlement, fabrication error, or gaps. Solve this equation together with equilibrium. A temperature gradient through depth can also cause curvature rather than pure uniform axial deformation; do not reduce that case to a single uniform ΔT without justification.
Final checks
Sketch the axial-force diagram, confirm each jump by joint equilibrium, convert all lengths before substituting, and estimate whether the deformation sign is physically sensible. For temperature, first ask whether movement is free, partial, or fully restrained. Finally separate response from capacity: calculated N , σ , and δ are demands, while yielding, buckling, fracture, and code resistance require their own checks.
Axial Audit Checklist
Establish the signed force and actual load path at every segment.
Match each segment with its material, area, modulus, length, and restraint.
Check both stress or capacity and compatible deformation before closing equilibrium.