Study guide
24.3 Concrete Cantilever, Gravity, and Basement Walls
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
24.3 Concrete Cantilever, Gravity, and Basement Walls
Key Takeaways Explain This Topic AI
A cantilever retaining wall requires separate stem, heel, toe, key, and connection free bodies; one external-stability resultant cannot design every component.
Stem flexure and shear follow the selected lateral pressure, while heel and toe design uses net upward and downward loads whose signs depend on the chosen cut and included soil.
Gravity walls rely primarily on mass and geometry but still need external stability, internal stress, joint, drainage, and foundation checks.
A basement wall restrained by floors or a roof may require at-rest pressure and a supported-span model rather than active pressure and a vertical cantilever model.
ACI 318-14 detailing, development, cover, temperature/shrinkage reinforcement, joints, drainage, and waterstops remain after flexure and shear calculations pass.
Last updated: July 2026
Retaining-wall type determines both structural model and pressure state. A freestanding cantilever stem, massive gravity wall, and floor-braced basement wall cannot share one shortcut. For July 2026, use the April 2024 PE Civil: Structural specification , ACI 318-14 , IBC 2018 , and the current PE Civil Reference Handbook. Do not import April 2027 editions.
Concrete Cantilever Wall Components
A reinforced concrete cantilever wall includes the vertical stem , base heel beneath retained soil, base toe in front, and sometimes a shear key. The wall-soil system is checked externally, but each concrete component needs its own free body and ACI strength/design details.
The stem usually acts as a vertical cantilever fixed near the base. Lateral earth, surcharge, compaction, and water pressures create flexure and shear that normally peak at the base. Main vertical reinforcement lies near the tension face determined by load direction, and must develop into the footing. Reversed or seismic loading can change the required reinforcement face. Horizontal reinforcement controls temperature, shrinkage, distribution, and cracking as required.
The heel and toe act as horizontal cantilevers from the stem. The heel commonly has downward retained-soil and slab weight opposed by upward foundation pressure; its usual net loading places main tension reinforcement near the top, but calculate the actual net diagram. The toe commonly carries upward foundation pressure and has main tension reinforcement near the bottom. These are common outcomes, not sign rules to memorize without a cut. Soil included as external-stability weight may appear as downward load on a heel component free body, while foundation reaction acts upward.
A shear key can add a structural path to deeper soil resistance, but it requires flexure, shear, development, and geotechnical resistance checks. Construction joints between stem and footing transfer shear and moment and need surface preparation, reinforcement continuity, and water control.
Worked Stem Demand
A 10 ft-high stem is designed for problem-given factored lateral pressure consisting of triangular soil pressure with maximum p_b = 0.800 ksf at the base plus uniform factored surcharge pressure p_q = 0.100 ksf . Find factored shear and base moment per foot of wall.
Triangular soil resultant:
P_s = (1/2)p_bH = (1/2)(0.800)(10) = 4.00 kips/ft
It acts at H/3 = 3.333 ft above the base.
Uniform surcharge resultant:
P_q = p_qH = (0.100)(10) = 1.00 kip/ft
It acts at H/2 = 5.0 ft .
Factored base shear:
V_u = 4.00 + 1.00 = 5.00 kips/ft
Factored base moment:
M_u = 4.00(3.333) + 1.00(5.0) = 18.33 kip-ft/ft
If a trial one-foot strip has supplied compatible design strengths φV_n = 9.0 kips/ft and φM_n = 22.0 kip-ft/ft , the stated shear and flexure checks pass. Utilizations are 5/9 = 0.556 and 18.33/22 = 0.833 . Development, minimum reinforcement, crack control, construction joints, footing components, and external stability still require checks.
Heel and Toe Free Bodies
For heel design, cut at the stem face and include downward soil, surcharge vertical effect if applicable, heel concrete, and upward contact pressure over the heel. The contact pressure is often nonuniform because the base resultant is eccentric. The net diagram can change along the heel, so use its actual moment and shear rather than total soil weight alone.
For the toe, include toe self-weight and upward pressure over the toe. Do not apply retained-soil weight over an exposed toe unless soil is actually present and reliably permanent. Critical flexural and one-way shear sections follow ACI 318-14 footing or wall-component provisions as applicable. Reinforcement must extend and develop through the stem-footing region.
Gravity Walls
A gravity wall uses concrete, masonry, stone, gabions, or another massive section so self-weight supplies stability. It still experiences internal compression and shear, base eccentricity, bearing, sliding, overturning, and global stability. Resultant location through horizontal joints or lift interfaces matters; a joint can slide or open before the overall base fails.
Mass concrete geometry does not excuse drainage. Water can dominate lateral force and create uplift. For segmental or block gravity systems, interface friction, shear keys, batter, connection, and facing stability need the controlling product or code model. Reinforced concrete gravity walls also need ACI temperature/shrinkage and joint detailing where applicable.
Restrained Basement Walls
A basement wall connected to a footing and floor diaphragm may be unable to rotate enough for active pressure. At-rest soil pressure, compaction pressure, surcharge, and water can govern. If the top slab braces the wall, the final structural model can span vertically between top and bottom instead of acting as a pure cantilever. Construction-stage behavior can differ before the floor is connected; temporary bracing or cantilever action may govern then.
A wall with openings needs lintel and jamb paths, local reinforcement, and diaphragm connection. Below-grade occupied space needs a coordinated drainage and waterproofing system. Waterproofing blocks leakage; drainage relieves pressure. Waterstops at joints and penetrations, crack control, and durable cover protect serviceability.
Component Workflow
Select active or at-rest pressure from wall restraint and stage.
Check external wall-soil stability.
Draw separate stem, heel, toe, key, and joint free bodies.
Calculate factored flexure and shear with correct net-load signs.
Design and develop reinforcement under ACI 318-14.
Verify drainage, waterstops, cover, joints, construction sequence, and foundation transfer.
The correct pressure coefficient does not rescue a component designed with the wrong support condition or reversed heel/toe load.