Study guide

24.1 Lateral Earth/Water Pressure and Drainage

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

24.1 Lateral Earth/Water Pressure and Drainage

Key Takeaways Explain This Topic AI

Active, at-rest, and passive coefficients represent different wall-movement conditions; soil type alone does not select the pressure state.

Layered-soil pressure is built from continuous vertical effective stress and layer-specific properties rather than restarting every pressure diagram at zero.

Uniform surcharge commonly adds a rectangular lateral-pressure component, while hydrostatic pressure is a separate triangular load using water depth and unit weight.

A drained soil model does not erase water pressure unless a reliable drainage path, filter, outlet, maintenance assumption, and groundwater condition support that model.

Soil and water forces need consistent effective- or total-stress treatment, correct resultants, and separate lever arms before combination.

Last updated: July 2026

A retaining wall responds to soil, surcharge, and water, but those loads do not all use the same coefficient or pressure diagram. For July 2026, use the April 2024 PE Civil: Structural specification , current PE Civil Reference Handbook, AASHTO LRFD Bridge Design Specifications 8th edition with the listed May 2018 errata , and IBC 2018 . Do not import April 2027 editions.

Select the Pressure State From Movement

Active pressure develops only after the wall moves sufficiently away from retained soil. Passive pressure develops when the wall moves into soil and usually requires much larger movement. At-rest pressure applies where lateral strain is restrained, such as a basement wall tied into stiff floors, or where movement is insufficient to mobilize active conditions.

  • For level, cohesionless backfill under the ideal Rankine assumptions,
  • K_a = (1 - sin φ)/(1 + sin φ)
  • K_p = (1 + sin φ)/(1 - sin φ)

For φ = 30° , K_a = 1/3 and K_p = 3 . These reciprocal values do not mean passive resistance is automatically available. Soil in front of a toe can be excavated, disturbed, frozen, scoured, or too shallow to mobilize the assumed resistance. At-rest K_0 follows the applicable geotechnical model or problem data; do not replace it with K_a because the smaller number is convenient.

Cohesion, wall friction, sloping backfill, seismic effects, compaction, and non-Rankine geometry require the controlling method rather than these simple expressions. Long-term permanent-wall design often neglects apparent cohesion unless specifically justified.

  • Build the Pressure Diagram
  • For drained cohesionless soil, horizontal effective pressure can be written
  • σ'_h = Kσ'_v

where σ'_v includes the effective weight of all soil above the point. In layered soil, calculate vertical stress continuously through each layer, then apply the coefficient appropriate to the layer and interface assumptions. Do not draw an independent triangle beginning at zero at every layer boundary; the overburden from upper layers remains. Abrupt changes in K can create pressure jumps, while changes in unit weight alter the slope. Integrate each segment for force and moment.

A uniform surface surcharge q commonly contributes constant lateral pressure Kq over wall height, producing a rectangular diagram. A strip, line, footing, or traffic surcharge has a different distribution and must use the method stated by the problem or AASHTO. Compaction equipment can create temporary pressure exceeding the final static case.

  • Water Is a Separate Load
  • Hydrostatic pressure varies as
  • u = γ_w z
  • For water depth H_w , resultant per foot of wall is
  • P_w = (1/2)γ_wH_w^2

acting H_w/3 above the bottom. Below groundwater, soil effective stress uses submerged or buoyant unit weight as appropriate, while pore-water pressure is added separately. Using saturated total unit weight in an effective-stress soil diagram and then adding full water can double count. Conversely, using drained soil properties and omitting water without a reliable drain can be unconservative.

Water can also act beneath a footing as uplift, behind a wall during a storm, or at different elevations on two sides. Rapid drawdown can remove stabilizing water faster than pore pressure dissipates. Use the actual hydraulic boundary and stage.

Worked Soil, Surcharge, and Clogged-Drain Case

A 10 ft wall retains level granular soil. The problem specifies γ = 120 pcf , φ = 30° , active Rankine conditions, and uniform surcharge q = 200 psf . First calculate the drained forces. Then, solely for comparison, the problem instructs that the soil components remain as calculated while a clogged drain creates a full-height hydrostatic load using γ_w = 62.4 pcf .

K_a = 1/3

Soil force:

P_a = (1/2)K_aγH^2 = (1/2)(1/3)(120)(10^2) = 2,000 lb/ft = 2.00 kip/ft

It acts at H/3 = 3.333 ft above the base.

Surcharge force:

P_q = K_aqH = (1/3)(200)(10) = 667 lb/ft = 0.667 kip/ft

It acts at H/2 = 5.0 ft .

Clogged-drain water force:

P_w = (1/2)(62.4)(10^2) = 3,120 lb/ft = 3.12 kip/ft

It acts 3.333 ft above the base. Total lateral force becomes 2.00 + 0.667 + 3.12 = 5.787 kip/ft . Base moment is

M = 2.00(3.333) + 0.667(5.0) + 3.12(3.333) = 20.4 kip-ft/ft

Without water, moment is only 10.0 kip-ft/ft . The simplified comparison shows why a drainage assumption is structurally significant; a real saturated-soil calculation must also update effective unit weights consistently.

Drainage Is a Designed System

A drainage blanket or free-draining backfill needs a filter compatible with retained soil so fines do not clog it. Perforated drains need slope, outlets, cleanouts, and protection from crushing or freezing. Weep holes need a functioning path and safe discharge. Surface grading and caps limit infiltration; waterproofing protects occupied space but does not by itself relieve pressure. Redundant or maintainable outlets matter where blockage is credible.

Exam Workflow

Establish wall movement and select active, at-rest, or passive conditions.

Draw soil layers, groundwater, drainage, surcharge, and stages.

Calculate continuous effective vertical stress and lateral soil pressure.

Add water separately with a consistent stress basis.

Integrate force and moment segment by segment.

Carry the load into wall and stability checks.

A pressure answer is incomplete until its state, drainage assumption, resultant, and lever arm are labeled.

Lateral pressure also acts near wall returns and corners; three-dimensional restraint can change local demand, so a per-foot two-dimensional result applies only where the actual geometry supports that idealization.