Study guide
10.2 Torsion and Warping Effects
PE Civil: Structural Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Identity and Reference Workflow
2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control
2 Chapter 2: Gravity and Construction Loads
2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads
3 Environmental Loads
Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads
4 Moving, Impact, and Lateral Soil Loads
Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads
5 Chapter 5: Load Paths and Combinations
5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations
6 Reactions, Diagrams, and Basic Axial Effects
Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation
7 Chapter 7: Axial Systems and Shear Effects
7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects
8 Flexure
Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure
9 Combined Stress and Deflection
Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods
10 Chapter 10: Serviceability, Torsion, and Stability
10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability
11 Fatigue, Robustness, Thermal, and Bearing Effects
Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress
12 Inspections, Submittals, and Adjacent Facilities
Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities
13 Chapter 13: Temporary Works and Safety
13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety
14 Soils and Core Concrete Properties
Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties
15 Chapter 15: Prestressed Concrete and Steel Properties
15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects
16 Timber, Masonry, and Material Conformance
Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance
17 Horizontal Members I
Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members
18 Chapter 18: Diaphragms and Vertical Members
18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls
19 Shear Walls, Trusses, and Frames
Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems
20 Composite/Bridge Systems and Bolted Connections
Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections
21 Chapter 21: Welded, Embedded, and Anchored Connections
21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections
22 Shallow Foundations
Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs
23 Deep Foundations
Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response
24 Chapter 24: Retaining Structures
24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls
10.2 Torsion and Warping Effects
Key Takeaways Explain This Topic AI
Torque follows from moment equilibrium about the member axis; an eccentric force produces T = Pe and requires a complete resisting path.
Equilibrium torsion is required to carry load to supports and cannot be discarded, while compatibility torsion arises from deformation restraint and may redistribute only when the governing model and code permit.
Circular-shaft formulas use the polar moment for circular sections; noncircular and thin-walled members require their appropriate torsion constant and warping model.
Open thin-walled sections are generally torsionally flexible, and restrained warping can create longitudinal normal stress in addition to Saint-Venant torsional shear.
Load location relative to the shear center and end restraint control twist, warping, and combined member demand.
Last updated: July 2026
Torsion is moment about a member's longitudinal axis. It may be obvious, as in a shaft, or hidden in an eccentric beam reaction. For July 2026, use the April 2024 Civil: Structural specification , current PE Civil Reference Handbook, ACI 318-14 , and the AISC Steel Construction Manual 15th edition . The April 2027 editions are future-only.
- Find the Torque and Its Path
- An eccentric transverse force P at perpendicular offset e creates torque
- T = Pe
provided the offset is measured from the axis or point through which the resisting shear acts. Draw the load, eccentricity, member axis, and reactions. Torque must pass through connections and supporting members into a stabilizing system. A numerical T with no connection or support path is incomplete.
For a beam cross-section, loading through the shear center can produce bending without twist in the ideal elastic model. The shear center equals the centroid for doubly symmetric sections but may lie elsewhere, even outside an open unsymmetric section. A load through the centroid is therefore not automatically torsion-free.
Equilibrium Versus Compatibility Torsion
Equilibrium torsion is necessary for static equilibrium. A canopy edge beam supporting an eccentric cantilever reaction may have no alternate path; removing torsional resistance would leave the load unsupported. The full demand must be traced, analyzed, and detailed.
Compatibility torsion develops because connected members are forced to deform together in a statically indeterminate system. A spandrel beam monolithic with transverse slab framing may attract torque as the system enforces joint rotation compatibility. Cracking or yielding can reduce torsional stiffness and redistribute actions if the governing ACI or AISC model permits it and the remaining load path and minimum detailing are adequate. “Compatibility” does not mean zero torsion by declaration. Determine whether redistribution is allowed; never discard equilibrium torsion.
A practical decision sequence is:
Take moments to calculate external torque and reactions.
Ask whether the structure remains in equilibrium if the member's torsional stiffness is released.
Identify section type, shear center, open or closed walls, and warping restraints.
Choose the applicable Saint-Venant, warping, concrete torsion, or code design model.
Calculate twist and stresses, including combined bending, shear, and axial effects.
Design the member and every torque-transfer connection using compatible demand and resistance formats.
- Circular-Shaft Mechanics
- For an elastic circular shaft,
- τ = Tr/J and θ = TL/(GJ)
where J is the polar moment, r is radial position, G is shear modulus, and θ is twist in radians. For a solid circle, J = πd^4/32 , and maximum stress occurs at r = d/2 .
A 4.0 in diameter solid steel shaft carries T = 24 kip-in over length L = 10 ft . Use G = 11,200 ksi .
- J = π(4^4)/32 = 25.13 in^4
- τ_max = (24 kip-in)(2 in)/(25.13 in^4) = 1.91 ksi
- θ = (24 kip-in)(120 in)/[(11,200 kip/in^2)(25.13 in^4)]
- θ = 0.01023 rad = 0.586°
The unit cancellation is a useful check. The calculated stress and twist are elastic responses, not code capacities. A strength check, service twist limit, fatigue requirement, or connection check still uses its applicable criteria.
Noncircular and Thin-Walled Members
Do not insert a rectangle, I-shape, channel, or angle into circular Tr/J formulas using the polar moment of area. Noncircular sections use a torsion constant , commonly also denoted J , whose value and stress distribution come from the appropriate theory or reference table. The same symbol does not make it the circular polar moment.
Closed thin-walled tubes develop circulating shear flow and are generally efficient in torsion. Open sections such as channels, angles, and wide-flange shapes have small Saint-Venant torsional stiffness. Their cross-sections may warp: longitudinal fibers displace different amounts. If warping is free, associated longitudinal restraint stress can be small; if a fixed end, diaphragm, or connection restrains warping, warping normal stresses and bimoment develop. End conditions can therefore change response even when applied torque is unchanged.
In steel, torsion may combine Saint-Venant shear, warping normal and shear stresses, bending, and local effects. The AISC 15th-edition provisions and design aids control the required checks. Lateral-torsional buckling of a beam involves coupled lateral displacement and twist under bending; it is related to torsional properties but is not the same calculation as a shaft under pure torque.
Reinforced Concrete Torsion
After cracking, reinforced concrete torsion is represented by a space-truss-type mechanism involving closed transverse reinforcement, longitudinal reinforcement, and diagonal compression. Required equilibrium torsion must be carried with ACI 318-14 strength and detailing provisions. Compatibility torsion may receive different treatment only under the code's conditions. Ordinary open stirrups or flexural bars assumed without anchorage do not automatically form the required torsional cage. Combined shear and torsion can govern transverse reinforcement.
Exam Checks
Preserve torque units—kip-ft versus kip-in is a factor of twelve. Mark whether twist is radians or degrees. Confirm J belongs to the actual section theory, locate the shear center, and identify warping restraint. Most importantly, state why the torque exists. If it is required by equilibrium, no assumed redistribution can make it disappear.
For a torque diagram, show concentrated and distributed torques, solve support torque by equilibrium, and plot internal T along the member. Internal torque changes where external torque enters; a change in section stiffness changes twist rate, not equilibrium torque by itself.