Study guide

Moment Frames and Stability Systems

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Moment Frames and Stability Systems

Key Takeaways Explain This Topic AI

Moment frames resist lateral load through beam and column flexure, joint shear, and connection moment transfer rather than diagonal axial action

Frame strength, story drift, connection deformation, foundation rotation, and global stability are separate acceptance questions

Sway classification follows lateral restraint and stiffness of the complete system, not simply whether a frame appears rectangular

Global P-Delta effects arise from gravity load acting through story displacement, while local P-delta effects arise from axial load acting through member curvature

Use stiffness assumptions consistent with AISC 15th, ACI 318-14, and ASCE 7-16 analysis rather than gross properties chosen only for convenience

Redundant frame lines improve alternative resistance only when diaphragms, collectors, connections, and foundations can deliver and redistribute force

Last updated: July 2026

Moment Frames and Stability Systems

For July 2026, use AISC 15th Edition , ACI 318-14 , and ASCE 7-16 . Moment frames can provide open architectural bays, but their lateral resistance depends on flexural members, joints, and connections. Passing a beam or column strength equation does not prove acceptable drift or system stability.

What makes a moment frame work

A moment-resisting connection transfers bending moment and shear between beam and column. Lateral story force causes beam and column curvature, joint or panel-zone shear, and base actions. The frame delivers overturning through column axial tension and compression and transfers base shear through column bases and foundations. Trace:

diaphragm → collector → frame beam/column joints → columns → bases/anchors → foundation → soil .

Model connection rigidity honestly. A fully restrained idealization assumes enough rotational stiffness to maintain the modeled joint angles; a simple shear connection does not suddenly become a moment joint because the analysis needs lateral resistance. Partially restrained behavior requires a consistent stiffness and strength model. Panel-zone deformation, beam-column connection deformation, column bases, and foundation rotation can contribute to drift.

Steel ordinary, intermediate, and special moment frames and reinforced-concrete moment-frame classifications have different permitted uses and detailing. Select the system under ASCE 7-16 and then apply the corresponding AISC 15th/AISC seismic or ACI 318-14 requirements. Do not choose a response modification coefficient from one system and detail another.

Sway, stiffness, and drift

An unbraced or sway frame relies on its own flexural stiffness to resist lateral translation. A frame may be part of a braced or nonsway gravity system when another sufficiently stiff system restrains story translation under the applicable analysis. Classification comes from structural behavior and the governing code procedure, not the presence of rectangular bays.

Member stiffness depends on EI , length, end restraint, axial force, connection behavior, and cracking where applicable. Steel analysis must use the AISC 15th stability method's prescribed stiffness treatment. Reinforced-concrete frames require ACI 318-14 stiffness assumptions that account for cracking and other applicable effects; using gross Ig for every member can underpredict drift and second-order response.

Story drift is the relative lateral displacement between adjacent floors, Δstory ; drift ratio is Δstory/hstory . It is not roof displacement divided by total height unless all story displacements happen to vary that way. Drift limits protect structural and nonstructural performance and can differ by hazard and occupancy. For seismic design, distinguish the elastic analysis displacement from the ASCE 7-16 amplified design story drift, using the prescribed Cd , importance, and analysis relationships. For wind or serviceability, use the applicable service load and stiffness criteria rather than importing seismic amplification.

Excessive drift can damage cladding, partitions, glazing, stairs, piping, and joints even when frame members remain nominally strong. Torsion can make the drift at one edge greater than the center-of-mass translation. Evaluate the location and direction required by the governing standard.

Worked one-story stiffness screen

Consider a one-story steel frame idealized as two identical columns with both ends rotationally fixed by a rigid beam and fixed bases. Neglect beam and connection deformation for this screening calculation. Each column has lateral stiffness 12EI/h³ , so

kstory = 24EI/h³ .

Let E = 29,000 ksi , I = 1,000 in⁴ , and h = 12 ft = 144 in . Then

kstory = 24(29,000)(1,000)/(144³) = 233.1 kip/in .

  • For a 60-kip lateral story force, the first-order displacement is
  • Δ = V/k = 60/233.1 = 0.257 in ,
  • and the drift ratio is

0.257/144 = 0.00179 .

This is not automatically the code design drift: the simplified boundary conditions, stiffness, hazard amplification, and other deformation sources must match the actual check. If the beam is flexible or bases rotate, stiffness decreases.

Suppose the total gravity load carried through the displaced story is 1,200 kip. The global second-order overturning increment represented by PΔ is

1,200(0.257) = 308 kip-in = 25.7 kip-ft .

The first-order story overturning is 60(12) = 720 kip-ft , so this simple ratio is about 25.7/720 = 3.6% . It illustrates why displacement and gravity load appear together in stability assessment; it is not a substitute for the exact AISC, ACI, or ASCE stability procedure and thresholds.

Second-order response

P-Delta ( P-Δ ) is the global effect of gravity load acting through translated story geometry. It increases story moments and drift and can create a feedback loop: more drift causes more moment, which causes more drift. P-delta ( P-δ ) is the member-level effect of axial force acting through curvature between member ends. Both can matter in a moment frame.

AISC 15th Edition provides permitted stability analysis approaches, including the direct-analysis framework and other specified methods. Follow one method completely, including required stiffness reductions, imperfections or notional loads, and second-order analysis or amplification. Do not combine an effective-length assumption from one method with stiffness treatment from another. ACI 318-14 provides its own nonsway/sway and second-order or moment-magnification provisions. Material methods should not be mixed.

Redundancy and the complete system

Multiple moment-frame bays or lines can reduce dependence on one element, but only if the diaphragm and collectors can distribute force and each line has foundations and connections. Force does not divide equally unless stiffness and compatibility support that assumption. A very stiff frame may attract most demand; torsional placement can overload an edge line.

Redundancy also does not excuse weak-column mechanisms, brittle connections, or missing continuity. Where the selected seismic system prescribes ductile yielding regions, connection qualification, strong-column relationships, or capacity design, use the exact 2026-listed provisions. Verify strength, drift, stability, and load path separately. The final frame is acceptable only when it can resist actions and remain stable at the required displacements.

System-Level Gate

  • Check What must remain compatible
  • Strength Member, connection, panel-zone, base, and foundation resistance
  • Drift Load basis, stiffness, amplification, and all modeled deformation sources
  • Stability Gravity load, second-order response, imperfections, and restraint model
  • Ductility Selected system classification, detailing, and intended yielding mechanism