Study guide

Shear Walls and Vertical Lateral Members

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Shear Walls and Vertical Lateral Members

Key Takeaways Explain This Topic AI

Trace lateral force from floor or roof diaphragm through collectors and chords into wall panels, boundary elements, anchorage, foundations, and soil

A shear wall resists both story shear and overturning; checking nominal shear strength alone does not establish a complete system

Overturning creates a boundary tension-compression couple whose anchorage and bearing demands depend on wall length, gravity load, and foundation restraint

Wall openings create piers, coupling beams or spandrels, collectors, and local boundary forces that must be represented in the model

Concrete, masonry, wood, and steel walls use different material checks but all require compatible boundary and connection load paths

Wall drift includes flexure, shear, connection slip, anchorage deformation, and foundation movement as applicable

Last updated: July 2026

Shear Walls and Vertical Lateral Members

For July 2026, use ACI 318-14 , TMS 402/602-16 , the 2018 NDS with 2015 SDPWS using ASD only , and AISC 15th Edition for their respective materials. Use the system and detailing provisions assigned by the problem; do not substitute later editions. Although wall materials differ, every acceptable solution must carry both horizontal shear and overturning effects to the ground.

Start at the diaphragm, not at the wall table

Wind or seismic inertia enters a roof or floor diaphragm through distributed surfaces and mass. The diaphragm carries in-plane shear; its chords resist diaphragm bending; collectors or drag struts gather force around openings, setbacks, or short wall lines. Connections deliver that force into vertical elements. The wall then delivers base shear, axial boundary forces, and overturning moment through anchors or dowels to the foundation and soil.

A complete sketch should show:

surface or mass → diaphragm → chord/collector → wall → boundary/anchorage → foundation → ground .

A wall shear capacity larger than story shear proves only one link. A weak collector splice, missing hold-down, inadequate concrete development, ungrouted masonry boundary cell, or flexible foundation can govern even when the wall panel itself is strong.

Shear and overturning act together

Story shear V tends to slide or rack the wall. Overturning moment M produces compression at one boundary and tension or reduced compression at the other. For a simple couple with boundary resultants separated by effective distance L , the approximate force is

T = C = M/L .

This relationship is equilibrium, not a material capacity equation. Gravity axial load can reduce uplift at one edge and increase compression at the other, but it must be included with the correct load combination. Do not count favorable dead load twice or assume it is present when an uplift combination reduces it. Base shear transfers separately through friction only where permitted, shear lugs, reinforcement, anchor groups, or bearing against the foundation.

Boundary demands also influence wall flexural strength and strain. ACI 318-14 concrete wall provisions may require concentrated longitudinal reinforcement and special boundary elements where the applicable seismic and compressive-strain criteria trigger them. Masonry boundary bars need grouted cells, development, and continuity under TMS 402/602-16. Wood shear-wall end posts and hold-downs collect chord forces; sheathing fasteners primarily assigned to panel shear cannot be assumed to supply the entire overturning tie. Steel plate shear walls require boundary beams and columns capable of receiving panel tension-field and overturning forces under the applicable AISC system requirements.

Wall types and deformation components

Wall system Principal resistance Boundary and connection focus

Reinforced concrete In-plane shear plus flexural compression and reinforcement tension Boundary reinforcement, coupling beams, dowels, development, foundation

Reinforced masonry Unit-mortar-grout assembly with bars in grouted cells Jamb/boundary cells, bond beams, laps, anchors, grout continuity

Wood structural-panel wall Sheathing and fastener shear with chord/end-post forces Edge nailing, blocking, collectors, hold-downs, sill anchorage; ASD only

Steel plate shear wall Plate shear and tension-field action in designed systems Boundary columns, beams, panel connections, bases

Wall drift can include flexural curvature, shear distortion, fastener or connection slip, hold-down elongation, anchor deformation, and foundation rotation. A stiff panel with flexible anchorage is not a stiff wall system. Use the material standard's required stiffness model and include components appropriate to the question.

Openings, piers, and coupling

Door and window openings divide a wall into piers and horizontal segments. A narrow pier may carry greater shear and overturning axial force than an average gross-wall calculation suggests. Reinforced-concrete coupling beams between wall piers can transfer shear and develop an overturning couple, but their strength, stiffness, rotation, and anchorage require the ACI model. Masonry bond beams and lintels have different detailing and should not inherit concrete coupling-beam assumptions.

In wood walls, segmented, perforated, or force-transfer-around-openings approaches have distinct SDPWS requirements. Do not blend their aspect ratios, unit shear, and anchorage rules. In every material, trace forces around an opening into collectors and boundary components. Distribution among several walls depends on diaphragm behavior, wall stiffness, torsion, and compatibility—not simply equal wall length.

Worked wall-base force path

A three-level diaphragm system delivers three lateral forces of 30 kip to a 20-ft-long wall at heights 12, 24, and 36 ft above its base. For this simplified equilibrium example,

  • Vbase = 30 + 30 + 30 = 90 kip ,
  • and

Mbase = 30(12) + 30(24) + 30(36) = 2,160 kip-ft .

Ignoring gravity-load redistribution for the moment, the boundary couple magnitude is

T = C = 2,160/20 = 108 kip .

The tension boundary and its splices, hold-downs, dowels, anchor rods, or other connections must deliver 108 kip through the wall-to-foundation interface under the controlling design method. The opposite boundary and foundation bearing region must accept the corresponding compression, modified by factored or service gravity load as appropriate. The base must also transfer 90 kip of horizontal shear.

If a diaphragm collector attaches 5 ft inside the wall boundary, local transfer forces must spread from that connection into the wall; using the full wall's average shear does not check the collector region. The foundation must resist sliding, overturning, bearing, uplift, and internal force transfer to soil. A 90-kip wall shear rating does not address the 108-kip boundary force.

Exam closeout

Check wall-system classification, material method, force distribution, openings, chord and collector delivery, base shear, boundary axial forces, drift components, and foundation response. Preserve ASD-only wood rules. When every arrow ends at a foundation reaction and every reaction has a resisting mechanism, the wall solution is finally complete.