Study guide

Soil Phase Relationships and Classification

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Soil Phase Relationships and Classification

Key Takeaways Explain This Topic AI

A soil phase diagram separates solids, water, and air volumes while soil weight is normally the sum of solids and water weights

Water content is based on dry-solids weight, void ratio on solids volume, porosity on total volume, and saturation on void volume

Total, dry, saturated, and submerged unit weights describe different water and buoyancy conditions and cannot be substituted silently

Percentages must be converted to decimals before using identities such as Se = wGs, and calculated saturation cannot exceed 100 percent

Gradation and Atterberg-limit classification requires the applicable 2026 handbook or AASHTO procedure rather than a soil name guessed from appearance

Last updated: July 2026

Soil Phase Relationships and Classification

Draw the boxes: Most phase-relation errors disappear when volumes and weights are placed in separate columns for solids, water, and air before a formula is selected.

The Three-Phase Model

Total volume contains solids and voids, while voids contain water and air:

V = V_s + V_v and V_v = V_w + V_a .

With air weight neglected, total weight is W = W_s + W_w . The standard dimensionless relationships are:

  • Quantity Definition Denominator to remember
  • Water content, w W_w/W_s Dry-solids weight
  • Void ratio, e V_v/V_s Solids volume
  • Porosity, n V_v/V Total volume
  • Saturation, S V_w/V_v Void volume
  • Solids specific gravity, G_s γ_s/γ_w Water unit weight reference

Porosity and void ratio are linked by n = e/(1 + e) and e = n/(1 - n) . For a consistent phase system, Se = wG_s , with w and S entered as decimals. Thus 12% water content is 0.12 , not 12 . A computed S > 1 signals inconsistent data, a percent conversion error, or an invalid assumption.

Moist-versus-dry measurement check

A specimen weighs 1,000 g before oven drying and 890 g after drying. The water mass is 1,000 - 890 = 110 g , but water content is

w = 110/890 = 0.1236 = 12.4% .

Dividing by the moist 1,000-g mass would give 11.0% and use the wrong denominator. The dry measurement represents solids mass; the lost mass represents water under the stated test assumptions.

Four Unit Weights

Unit weight always means weight divided by a stated volume, but the water condition changes the numerator:

  • dry: γ_d = G_sγ_w/(1 + e) ; water weight is omitted;
  • total or moist: γ = G_s(1 + w)γ_w/(1 + e) = γ_d(1+w) ;
  • saturated: γ_sat = (G_s + e)γ_w/(1 + e) ; every void is water-filled;

submerged or buoyant: γ' = γ_sat - γ_w = (G_s - 1)γ_w/(1 + e) .

Submerged unit weight is useful for effective overburden below a water table. It is not the soil's total saturated unit weight and should not be used to calculate total gravity load. Use γ_sat for total soil weight and subtract pore-water pressure when effective stress is needed.

Worked Phase-Relationship Example

A soil has G_s = 2.70 , e = 0.65 , and w = 12% = 0.12 . Use γ_w = 62.4 pcf .

First compute porosity:

n = 0.65/(1 + 0.65) = 0.3939 = 39.4% .

Use Se = wG_s to find saturation:

S = 0.12(2.70)/0.65 = 0.498 = 49.8% .

The dry unit weight is

γ_d = 2.70(62.4)/(1.65) = 102.1 pcf .

The actual moist unit weight is

γ = 102.1(1 + 0.12) = 114.4 pcf .

For the same solids and void ratio at complete saturation,

γ_sat = (2.70 + 0.65)(62.4)/1.65 = 126.7 pcf .

and

γ' = 126.7 - 62.4 = 64.3 pcf .

The ordering check is sensible: γ_d < γ < γ_sat , and the submerged value is saturated unit weight minus water unit weight. The actual sample is only 49.8% saturated, so γ_sat describes a hypothetical saturated state rather than its current total unit weight.

Gradation of Coarse-Grained Soil

A sieve analysis reports percent passing versus particle size. Determine the fractions retained above and passing the classification sieve specified by the applicable system; do not assume all sand- or gravel-sized material behaves as fines. On a semilog gradation curve, D_10 , D_30 , and D_60 are particle sizes at 10%, 30%, and 60% passing. Common shape measures are

  • C_u = D_60/D_10
  • and

C_c = D_30²/(D_10D_60) .

For example, if D_10 = 0.15 mm , D_30 = 0.35 mm , and D_60 = 0.75 mm , then C_u = 5.0 and C_c = 0.35²/[0.15(0.75)] = 1.09 . These numbers still do not determine a symbol until fines content and the classification limits are checked.

These coefficients describe spread and curve shape, but classification also depends on gravel/sand proportions, fines content, and the system's boundary criteria. Use the PE Civil handbook active for the test date or the specified AASHTO LRFD 8th-edition procedure, including its identified May 2018 errata, rather than memorizing a symbol without its limits.

Atterberg Limits for Fine-Grained Soil

The liquid limit LL marks the boundary between liquid and plastic behavior; the plastic limit PL marks the boundary between plastic and semisolid behavior. Plasticity index is

PI = LL - PL .

If LL = 48 and PL = 22 , then PI = 26 . Plot the stated LL and PI on the applicable plasticity chart to distinguish silt-like and clay-like behavior and low versus high plasticity. Boundary points may require dual symbols or additional information. Organic behavior, gradation, and visual description must be handled according to the requested classification system.

Classification Workflow

Confirm whether data are masses, weights, or volumes and convert every percent to a decimal for equations.

Draw the phase diagram and calculate independent quantities before using derived identities.

Check 0 ≤ n < 1 , e ≥ 0 , and 0 ≤ S ≤ 1 .

For classification, determine coarse versus fine fraction from the required sieve.

For coarse soil, evaluate gravel/sand split, fines, C_u , and C_c ; for fine soil, calculate PI and use the chart.

Report the classification symbol and descriptive name from the same system.

Do not mix a USCS symbol, an AASHTO group threshold, and a casual field description into one unsupported classification.