Study guide

Soil Strength, Permeability, and Compressibility

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

Soil Strength, Permeability, and Compressibility

Key Takeaways Explain This Topic AI

Effective stress carried by the soil skeleton is σ′ = σ − u; total stress and pore-water pressure must be calculated separately

Drained effective-stress parameters and undrained total-stress strength belong to different drainage and time models and cannot be mixed

Darcy flow depends on hydraulic conductivity, hydraulic gradient, and flow area, while upward seepage can reduce effective stress

Primary consolidation couples pore-pressure dissipation with time-dependent settlement, so drainage path and loading duration matter

Immediate, primary-consolidation, and secondary settlements represent different mechanisms and should be evaluated with compatible parameters

Last updated: July 2026

Soil Strength, Permeability, and Compressibility

Choose the time model: The same saturated soil can behave undrained during rapid loading and drained after pore pressures dissipate. Strength and settlement parameters must match that drainage condition.

  • Total Stress, Pore Pressure, and Effective Stress
  • For saturated soil, Terzaghi effective stress is
  • σ' = σ - u ,

where σ is total normal stress and u is pore-water pressure. Total stress comes from total unit weight and external loads. Hydrostatic pore pressure is u = γ_w h_w below the water surface. Effective stress is carried by the soil skeleton and governs many drained strength and compressibility relationships.

A useful check below a static water table is that the effective overburden increment equals submerged unit weight times depth. Do not calculate total stress using γ' and then subtract water pressure again; that removes buoyancy twice.

Worked effective stress and drained strength

A 20-ft saturated soil layer begins at the water table. Let γ_sat = 120 pcf , γ_w = 62.4 pcf , and use problem-given drained parameters c' = 0 , φ' = 30° . At the base:

  • σ_v = 120(20) = 2,400 psf ,
  • u = 62.4(20) = 1,248 psf ,
  • and

σ'_v = 2,400 - 1,248 = 1,152 psf .

This also equals (120 - 62.4)(20) = 1,152 psf . The Mohr–Coulomb drained shear-strength expression is

τ_f = c' + σ'_n tanφ' .

Using the vertical effective stress as the stated normal stress for this illustrative plane,

τ_f = 0 + 1,152 tan30° = 665 psf .

This is a drained effective-stress calculation. It cannot be converted into a rapid undrained clay calculation merely by replacing one coefficient.

Drainage and Time

Condition Common analysis framework Why

Rapid loading of saturated low-permeability clay Undrained, often total stress using s_u Excess pore pressure has little time to dissipate

Long-term loading after drainage Effective stress using c' and φ' Soil skeleton carries the changed effective stress

  • Permeable sand with short drainage path Often drained Pore pressure can dissipate relatively quickly
  • Partially drained condition Coupled/time-dependent analysis Neither ideal limit may represent behavior

These are reasoning guides, not automatic labels. Compare loading duration with drainage time, permeability, and drainage path. Never combine total normal stress with c',φ' , or effective normal stress with an undrained s_u , unless a specified formulation explicitly defines that combination. For a 2026 exam, use the current PE Civil handbook and AASHTO LRFD 8th edition with its May 2018 errata.

  • Permeability and Seepage
  • Darcy's law for one-dimensional laminar flow is
  • Q = kiA ,

where k is hydraulic conductivity, i = Δh/L is hydraulic gradient, and A is cross-sectional area normal to flow. If k = 2.0 × 10⁻⁴ ft/min , i = 0.50 , and A = 30 ft² , then

Q = 2.0 × 10⁻⁴(0.50)(30) = 0.0030 ft³/min .

This Q/A is Darcy discharge velocity, not necessarily the average velocity through pore space. Flow through a smaller void area is faster. Hydraulic conductivity depends on soil fabric, void ratio, fluid properties, and saturation. Layering also makes horizontal and vertical equivalent conductivities different.

Seepage direction matters. Downward seepage increases effective stress relative to a hydrostatic profile; upward seepage reduces it. Near an excavation or hydraulic exit, sufficient upward gradient can cause boiling or piping. Draw total head and flow direction rather than assigning pore pressure from depth alone when conditions are nonhydrostatic.

Compressibility and Consolidation

Immediate settlement occurs with prompt soil deformation and is often important in granular soils. Primary consolidation in saturated fine-grained soil occurs as excess pore pressure dissipates and effective stress rises. Secondary compression continues after primary consolidation under sustained effective stress due to soil-structure rearrangement.

For a normally consolidated layer under a stated one-dimensional model, a problem may give

S_c = [C_c H/(1 + e_0)] log10(σ'_f/σ'_0) .

Let H = 10 ft , e_0 = 0.80 , C_c = 0.25 , initial effective stress σ'_0 = 1,000 psf , and final effective stress σ'_f = 1,500 psf . Then

S_c = [0.25(10)/(1.80)]log10(1,500/1,000)

S_c = 0.2446 ft = 2.93 in .

Do not use layer-top stress when the method calls for a representative layer stress, and do not use total stress in the logarithmic effective-stress ratio. For overconsolidated soil, stress history and preconsolidation stress may require recompression and virgin-compression segments rather than one C_c expression.

Consolidation Rate

Settlement magnitude and settlement time are separate questions. The rate depends on coefficient of consolidation and drainage length. A layer draining from both faces has a shorter maximum drainage path than the same thickness draining from one face and therefore reaches a given degree of consolidation sooner, all else equal. Apply the handbook's time-factor relationship with the correct drainage boundary.

Integrated Workflow

Draw layers, loads, water levels, and drainage boundaries.

Compute total stress and pore pressure independently; subtract once for effective stress.

Decide drained, undrained, or time-dependent behavior from permeability, path, and loading duration.

Use strength parameters that belong to that stress framework.

For seepage, determine head loss, gradient, flow area, and direction.

Separate settlement magnitude into immediate, primary, and secondary components as required.

Check units and whether the requested answer describes short-term safety, long-term safety, settlement amount, or settlement rate.