Study guide

21.2 Bearing, Embedded, and Precast Connections

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

21.2 Bearing, Embedded, and Precast Connections

Key Takeaways Explain This Topic AI

A bearing plate must distribute compression while satisfying plate bending, contact, supporting-material bearing, edge, splitting, and the downstream load path.

Embed plates transfer tension, shear, and moment through plate bending, welds, headed studs or reinforcing bars, concrete anchorage modes, and surrounding-member reinforcement.

Corbels and short brackets require a compatible strut-and-tie or code model, anchored primary tie, bearing, shear-transfer, and local confinement checks.

Headed studs can serve different composite or anchorage roles; their steel strength does not replace concrete breakout, pryout, edge, spacing, or group checks.

Precast seats, pads, ties, and connections must accommodate tolerances, rotation, movement, erection stability, and positive force transfer at every construction stage.

A connector that passes in isolation can still fail through local plate deformation, concrete breakout, inadequate reinforcement development, or the supporting member.

Last updated: July 2026

Embedded and bearing connections introduce concentrated force into concrete or a precast member. Their visible steel is rarely the whole connection. For July 2026, use the April 2024 PE Civil: Structural specification , ACI 318-14 , PCI Design Handbook 7th edition , and the AISC Steel Construction Manual 15th edition . Do not import April 2027 standards.

Bearing Plates: Follow the Pressure

A bearing plate spreads a column, beam, girder, or precast reaction over a larger area. Begin with force and moment at the contact surface. Check whether full contact is possible, then evaluate maximum pressure rather than only P/A . The plate must also span between the loaded footprint and supporting reaction, so plate bending and yielding can govern. Grout, concrete, masonry, a bearing pad, or soil below the plate needs its own compatible bearing limit and adequate dimensions.

Compression must continue through the supporting member. Near an edge, concentrated bearing can split or spall concrete. Deep within a member, bursting or transverse tension may require reinforcement. A base plate with moment can lift off on one side, forcing compression into a smaller region and tension into anchors. Concrete contact cannot carry tension merely because an elastic formula reports negative pressure.

Worked Eccentric Bearing Plate

A rigid 12 in-wide by 18 in-long bearing plate carries factored compression P_u = 240 kips and factored moment M_u = 30 kip-ft about the axis parallel to its 12 in width. Assume linear pressure and full contact for the trial calculation. Find extreme pressures.

Contact area:

A = (12)(18) = 216 in^2

Contact section modulus for pressure varying along the 18 in length:

S = BL^2/6 = (12)(18^2)/6 = 648 in^3

Convert moment:

M_u = 30(12) = 360 kip-in

Average pressure:

P_u/A = 240/216 = 1.111 ksi

Bending component:

M_u/S = 360/648 = 0.556 ksi

Extreme pressures:

  • q_max = 1.111 + 0.556 = 1.667 ksi
  • q_min = 1.111 - 0.556 = 0.555 ksi

Both are compressive, so full contact is plausible for the stated idealization. The eccentricity e = M/P = 360/240 = 1.5 in is below the kern limit L/6 = 3.0 in , confirming the sign check. If the problem supplies compatible concrete design bearing stress 1.80 ksi, the stated contact-pressure check passes because 1.667 < 1.80 ksi . Plate flexure, grout, local reinforcement, edges, anchors, and the receiving member still require checks.

Embed Plates and Headed Studs

An embed assembly can include a face plate, headed studs, deformed-bar anchors, welds, stiffeners, and reinforcing bars tied into the member. Resolve applied force into tension, shear, and moment at the plate. Plate flexure can make anchor demand nonuniform; prying can amplify tension. Welds must develop force between attachment and plate, while studs or bars transfer it from plate into concrete.

For headed anchors, possible modes include anchor steel failure, concrete tension breakout, pullout, side-face blowout where applicable, shear breakout, and pryout. Group effects, close edges, spacing, member thickness, cracked-concrete condition, and supplementary reinforcement affect resistance. A high-strength stud does not make a thin edge region stronger. Reinforcement intended to bypass breakout must be positioned, anchored, and detailed to receive the force.

Headed studs used for steel-concrete composite beam action transfer longitudinal interface shear under AISC provisions. Studs welded to an embed plate can instead act as concrete anchors under ACI. Similar hardware does not make the design models interchangeable; identify the force-transfer role.

Corbels and Short Brackets

A corbel carries a concentrated reaction over a short shear span. Ordinary slender-beam behavior may not represent its disturbed stress field. Use the ACI 318-14 corbel or permitted strut-and-tie model required by the problem. The load flows through a concrete compression strut and anchored steel tie, with bearing, interface shear, confinement, and local nodal zones.

The primary tie must develop beyond the loaded region, and horizontal force from creep, shrinkage, restraint, braking, or bearing friction may accompany vertical reaction. Welding or anchoring the supported member to the corbel changes that horizontal path. Check the column or wall receiving the corbel force; a corbel that passes locally can overload the parent member.

Precast Seats, Pads, and Ties

A precast beam seat needs adequate bearing length after erection tolerances, movement, rotation, and edge clearances are considered. Bearing pads distribute stress and permit intended rotation or movement, but they can bulge, slip, or create edge pressure. Do not use nominal seat length when the problem calls for net length after tolerances. Local ledges, dapped ends, hanger reinforcement, and splitting zones can govern.

Positive ties and connections establish diaphragm, robustness, uplift, or lateral transfer. Gravity bearing alone cannot resist tension. During erection, temporary braces and anchors stabilize panels before roof or floor diaphragms exist. Welded embeds, bolts, dowels, grouted sleeves, and closure pours develop their final roles only after the specified installation, cure, and inspection sequence.

Connection Audit

Resolve force and moment at the interface.

Check contact, plate or seat deformation, and local bearing.

Trace force through welds, studs, bars, pads, ties, and anchors.

Check steel and concrete modes, edges, group effects, and reinforcement development.

Evaluate erection tolerances, temporary stability, movement, and final continuity.

Continue the path through the supporting member and foundation.

The governing result is the weakest compatible link, not the catalog strength of the most visible connector.