Study guide

21.1 Welded Steel Connections

PE Civil: Structural Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Identity and Reference Workflow

2026 PE Civil: Structural Identity, Format, and Scoring Electronic Handbook, Design Standards, Units, and Version Control

2 Chapter 2: Gravity and Construction Loads

2.1 Dead Loads and Self-Weight 2.2 Live Loads, Reduction, and Load Placement 2.3 Construction-Stage Loads

3 Environmental Loads

Wind Loads and Pressure Paths Seismic Loads and Lateral Force Distribution Snow, Rain, and Ice Loads

4 Moving, Impact, and Lateral Soil Loads

Vehicular, Crane, and Other Moving Loads Impact and Dynamic Allowances Earth Pressure and Surcharge Loads

5 Chapter 5: Load Paths and Combinations

5.1 Tributary Areas and Complete Vertical/Lateral Load Paths 5.2 Strength and Service Load Combinations

6 Reactions, Diagrams, and Basic Axial Effects

Free-Body Diagrams, Reactions, Shear, and Moment Qualitative Diagrams, Influence Lines, and Critical Placement Axial Tension, Compression, and Deformation

7 Chapter 7: Axial Systems and Shear Effects

7.1 Trusses, Braces, and Column Axial Force 7.2 Shear Stress, Shear Flow, and Built-Up Sections 7.3 One-Way, Two-Way, Punching, and Interface Shear Effects

8 Flexure

Section Properties and Elastic Flexural Stress Beam and Slab Flexural Load Effects Biaxial and Unsymmetrical Flexure

9 Combined Stress and Deflection

Combined Axial and Flexural Stress Principal Stress, Mohr's Circle, and Combined Shear Elastic Deflection Methods

10 Chapter 10: Serviceability, Torsion, and Stability

10.1 Serviceability: Deflection, Drift, Vibration, and Ponding 10.2 Torsion and Warping Effects 10.3 Buckling, Effective Length, and Second-Order Stability

11 Fatigue, Robustness, Thermal, and Bearing Effects

Fatigue and Progressive-Collapse Concepts Thermal Deformation and Bearing/Contact Stress

12 Inspections, Submittals, and Adjacent Facilities

Special Inspections and Verification Duties Shop Drawings, Submittals, RFIs, and Delegated Design Construction Effects on Adjacent Facilities

13 Chapter 13: Temporary Works and Safety

13.1 Formwork, Falsework, Scaffolding, Shoring/Reshoring, Bracing, and Anchorage 13.2 Construction, Roadside, and Work-Zone Safety

14 Soils and Core Concrete Properties

Soil Phase Relationships and Classification Soil Strength, Permeability, and Compressibility Fresh and Hardened Concrete Properties

15 Chapter 15: Prestressed Concrete and Steel Properties

15.1 Reinforced, Precast, Pretensioned, and Post-Tensioned Concrete Materials 15.2 Structural and Cold-Formed Steel Properties 15.3 Steel Toughness, Weldability, Corrosion, and Temperature Effects

16 Timber, Masonry, and Material Conformance

Timber Properties and ASD Design Values Masonry, CMU, Mortar, Grout, and Brick Veneer Properties Concrete and Masonry Test Methods Steel, Timber, and Other Material Specification Conformance

17 Horizontal Members I

Steel Beams and Girders Reinforced Concrete Beams and Slabs Timber and Masonry Horizontal Members

18 Chapter 18: Diaphragms and Vertical Members

18.1 Diaphragms, Collectors, Struts, and Composite Slabs 18.2 Steel Columns and Beam-Columns 18.3 Concrete Columns and Bearing Walls

19 Shear Walls, Trusses, and Frames

Shear Walls and Vertical Lateral Members Trusses and Braced Systems Moment Frames and Stability Systems

20 Composite/Bridge Systems and Bolted Connections

Composite Construction and Structural System Selection Bridge Systems and Load Distribution Bolted Steel Connections

21 Chapter 21: Welded, Embedded, and Anchored Connections

21.1 Welded Steel Connections 21.2 Bearing, Embedded, and Precast Connections 21.3 Anchors, Post-Installed Anchors, and Wood/Masonry Connections

22 Shallow Foundations

Isolated, Spread, and Strip Footings Combined and Strap Footings Mat Foundations and Foundation Slabs

23 Deep Foundations

Driven Piles: Axial Capacity and Settlement Drilled Shafts, Piers, and Caissons Pile Groups, Caps, and Lateral Deep-Foundation Response

24 Chapter 24: Retaining Structures

24.1 Lateral Earth/Water Pressure and Drainage 24.2 Sliding, Overturning, Bearing, and Global Stability 24.3 Concrete Cantilever, Gravity, and Basement Walls 24.4 Sheet-Pile, Anchored, and Mechanically Stabilized Earth Walls

21.1 Welded Steel Connections

Key Takeaways Explain This Topic AI

A welded connection must transfer force through the weld metal, heat-affected and connected base metal, and the supporting member; the weld is only one link.

For a standard equal-leg 90-degree fillet weld, effective throat is 0.707 times leg size, while effective length follows the AISC 15th-edition geometry rules rather than gross drawn length.

Complete-joint-penetration and partial-joint-penetration groove welds have different effective areas, access, qualification, and applicable strength checks.

An eccentric weld group carries direct force plus moment-induced shear whose magnitude and direction vary with location; vector combination governs the critical point.

LRFD weld demand must be compared with LRFD design strength and ASD demand with allowable strength, including connected-material yielding, rupture, and block shear checks.

Last updated: July 2026

A weld transfers force only when its geometry, metal, connected parts, and load path all work together. A strong weld deposited on a thin plate can simply move failure into the plate. For July 2026, use the April 2024 PE Civil: Structural specification , current PE Civil Reference Handbook, and the AISC Steel Construction Manual 15th edition . Do not import the April 2027 reference set.

Read the Connection Before Calculating

Start with the force path and weld symbol. Identify the connected parts, force direction, weld type, leg or groove dimensions, length, continuity, access, and whether demand is concentric or eccentric. Then select LRFD or ASD and keep demand and resistance on that basis. A weld drawn in elevation may occur on one side, both sides, intermittently, or all around; counting nonexistent segments is a common error.

Fillet welds have an approximately triangular cross-section. For an equal-leg weld joining surfaces at 90 degrees, the effective throat is

t_e = 0.707w

where w is fillet leg size. Effective weld area is throat times effective length, not leg size times visible length. AISC rules address minimum and maximum size, effective length, end returns, terminations, and long end-loaded joints. If a problem states effective length, do not subtract an end correction again.

Groove welds can be complete-joint-penetration or partial-joint-penetration. A CJP groove weld extends through the joint thickness as qualified and can develop different base-metal behavior than a PJP weld with a specified effective throat. Groove angle, root opening, backing, access, welding position, and procedure affect execution. “Full-length groove weld” does not by itself prove CJP. Use the symbol and effective-throat provisions.

Worked Concentric Fillet-Weld Strength

Two effective 6.0 in-long fillet welds, one on each side of a plate, transfer concentric shear. Each weld has leg size w = 1/4 in and uses an E70 electrode. The problem directs the AISC LRFD fillet-weld model F_nw = 0.60F_EXX , with φ = 0.75 , and states the full 6.0 in is effective. Find weld-metal design strength.

Total effective length:

L_e = 2(6.0) = 12.0 in

Effective throat:

t_e = 0.707(0.25) = 0.1768 in

Effective weld area:

A_we = t_eL_e = (0.1768)(12.0) = 2.121 in^2

Nominal weld strength:

R_n = (0.60)(70 ksi)(2.121 in^2) = 89.1 kips

LRFD design strength:

φR_n = (0.75)(89.1) = 66.8 kips

If factored shear is 60.0 kips, weld-metal utilization is 60.0/66.8 = 0.898 , so that stated limit state passes. If the problem separately gives connected-plate design rupture strength of 55 kips, the connection still fails because the base material governs. Never stop after the first passing resistance.

The calculation assumes force distribution appropriate to the stated concentric pair and the problem-provided AISC model. Weld directionality provisions, load angle, effective length, and electrode compatibility must follow the actual question.

Eccentric Weld Groups

When load misses the weld-group centroid, replace it at the centroid with the same force plus torque T = Pe . Direct shear is distributed through effective weld area or length as the adopted elastic method specifies. Moment-induced shear at a weld point is tangent to the radius from the group centroid and proportional to radius:

q_T = Tr/J_w

where J_w is the weld group's polar property on the same line- or area-based convention used for q_T . Direct and torsional shear are vectors; at one point they reinforce and at another they oppose. Adding only magnitudes everywhere can misidentify the critical location.

Use this sequence:

Locate the effective weld-group centroid.

Resolve forces and calculate moments about that centroid.

Compute group length, area, and directional properties consistently.

Evaluate direct and moment-induced components at candidate extreme points.

Combine vectors and compare the largest resultant with compatible resistance per unit length or stress.

Check deformation or instantaneous-center behavior if the problem requires that method.

For combined shear and tension, use the AISC interaction and directional provisions identified by the question; do not invent a scalar sum.

Base Metal and Detail Checks

The connected plate, gusset, flange, web, or HSS face may govern through gross yielding, net-section rupture, block shear, local bending, shear yielding, tear-out, crippling, or punching-type behavior. At an HSS wall, connection flexibility and local limit states can control before weld metal. An eccentric weld can also bend the connected element. Check the supporting member and the connection between it and the next component.

Weld quality depends on compatible base and filler metal, qualified procedure, fit-up, access, preheat or heat control where required, and inspection. Longer or larger welds are not automatically better: excess heat and restraint can increase distortion or residual stress, and an oversized weld can be difficult to place soundly. Intermittent welds may be prohibited in certain exposure or load conditions and must meet length and spacing rules.

Final Audit

Label every dimension as leg, throat, actual length, or effective length. Preserve kip-in versus kip-ft in eccentricity. Then verify weld metal, base metal, block shear, local supporting-member behavior, and force transfer beyond the connection. The governing strength is the smallest compatible design or allowable resistance, not the most convenient weld calculation.

When weld groups join parts of different thickness, also verify through-thickness demand, weld access, and whether force entering through one plane creates secondary eccentricity. Connection geometry controls both structural demand and practical inspectability.