Study guide
12.1 Culvert Design and Inlet/Outlet Control
PE Civil: Transportation Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Project Management
1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis
2 Chapter 2: Traffic Engineering - Capacity and Flow
2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis
3 Chapter 3: Traffic Engineering - Studies and Safety
3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)
4 Chapter 4: Roadside and Cross-Section Design
4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations
5 Chapter 5: Horizontal Alignment Design
5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions
6 Chapter 6: Vertical Alignment Design
6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures
7 Chapter 7: Intersection Geometry and Layout
7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry
8 Chapter 8: Traffic Signals
8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption
9 Chapter 9: Traffic Control Design
9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones
10 Chapter 10: Geotechnical and Pavements
10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs
11 Chapter 11: Hydrology and Open-Channel Drainage
11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality
12 Chapter 12: Drainage Structures and Systems
12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities
12.1 Culvert Design and Inlet/Outlet Control
Key Takeaways Explain This Topic AI
Inlet control occurs when the flow capacity is governed solely by the inlet geometry (cross-sectional area, inlet edge, shape), regardless of the culvert barrel roughness, length, or slope.
Outlet control exists when the culvert capacity is limited by downstream conditions, barrel characteristics, or tailwater, requiring calculation of head losses: entrance ( H e = k e V 2 / 2 g H_e = k_e V^2/2g H e = k e V 2 /2 g ), friction ( H f H_f H f ), and exit ( H o = V 2 / 2 g H_o = V^2/2g H o = V 2 /2 g ).
The governing headwater depth ( H W HW H W ) is the greater of the calculated inlet control headwater ( H W i HW_i H W i ) and outlet control headwater ( H W o HW_o H W o ), i.e., H W = max ( H W i , H W o ) HW = \max(HW_i, HW_o) H W = max ( H W i , H W o ) .
For outlet control, critical depth ( d c d_c d c ) is determined at the outlet. If tailwater ( T W TW T W ) is less than D D D , the equivalent hydraulic depth parameter h o h_o h o is estimated as max ( T W , ( d c + D ) / 2 ) \max(TW, (d_c + D)/2) max ( T W , ( d c + D ) /2 ) .
Energy dissipation systems, such as riprap aprons designed per FHWA HEC-14, must scale median stone size ( d 50 d_{50} d 50 ) and apron length ( L a L_a L a ) based on the outlet Froude number ( F r Fr F r ) and discharge velocity ( V V V ).
Last updated: July 2026
- Culvert Design and Inlet/Outlet Control
- Culvert Hydraulics Overview
Culverts are closed conduits used to convey water through highway embankments or other obstructions. Unlike open channels, culverts operate under complex hydraulic conditions that can transition between open-channel flow, gravity full pipe flow, and pressurized sewer flow. The design of a culvert is based on the concept of "control," which refers to the specific location that limits the hydraulic capacity of the structure. Culverts are classified as operating under either Inlet Control or Outlet Control .
Inlet Control Characteristics
Under inlet control, the flow capacity of the culvert is determined solely by the geometry of the inlet. The barrel of the culvert is capable of conveying more flow than the inlet can accept. Consequently, downstream factors such as culvert roughness, length, slope, and tailwater levels do not affect the headwater elevation, provided the tailwater does not submerge the inlet.
Flow Regime: The flow inside the culvert barrel is typically supercritical, and the culvert behaves as an open channel.
Governing Factors:
Inlet cross-sectional area ( A A A ).
Inlet shape (circular, box, arch).
Inlet edge configuration (e.g., beveled edges, square edges, projecting ends).
Headwater depth ( H W HW H W ).
Inlet Edge Performance: The shape of the inlet edge significantly affects the flow contraction. A projecting barrel end causes the most flow contraction and has the lowest capacity, whereas a headwall with beveled edges or a tapered inlet minimizes contraction, resulting in a higher capacity for the same headwater depth.
For design, the Federal Highway Administration (FHWA) HDS-5 manual provides empirical equations to calculate the headwater depth ( H W HW H W ) required for a given discharge ( Q Q Q ).
For unsubmerged conditions ( Q / A D 0.5 < 3.5 Q / A D^{0.5} < 3.5 Q / A D 0.5 < 3.5 ): H W i D = H c D + c ( Q A D 0.5 ) M − 0.5 S 0 \frac{HW_i}{D} = \frac{H_c}{D} + c \left( \frac{Q}{A D^{0.5}} \right)^M - 0.5 S_0 D H W i = D H c + c ( A D 0.5 Q ) M − 0.5 S 0
For submerged conditions ( Q / A D 0.5 ≥ 4.0 Q / A D^{0.5} \ge 4.0 Q / A D 0.5 ≥ 4.0 ): H W i D = a ( Q A D 0.5 ) 2 + Y − 0.5 S 0 \frac{HW_i}{D} = a \left( \frac{Q}{A D^{0.5}} \right)^2 + Y - 0.5 S_0 D H W i = a ( A D 0.5 Q ) 2 + Y − 0.5 S 0
Where:
- H W i HW_i H W i = Headwater depth above inlet invert (ft)
- D D D = Interior height of culvert barrel (ft)
- H c H_c H c = Specific head at critical depth ( d c + V c 2 / 2 g d_c + V_c^2/2g d c + V c 2 /2 g ) (ft)
- Q Q Q = Discharge (cfs)
- A A A = Full cross-sectional area of the barrel (sf)
- S 0 S_0 S 0 = Culvert barrel slope (ft/ft)
- a , c , M , Y a, c, M, Y a , c , M , Y = Constants based on inlet type (from HDS-5 tables)
- Outlet Control Characteristics
Under outlet control, the capacity of the culvert is limited by downstream conditions, barrel characteristics, and the inlet geometry. The flow is subcritical, or the barrel flows full, meaning the downstream water level or friction in the pipe exerts a backwater effect all the way to the inlet.
Governing Factors:
Inlet geometry (cross-sectional area A A A and entrance loss coefficient k e k_e k e ).
Barrel characteristics (length L L L , roughness Manning's n n n , and slope S 0 S_0 S 0 ).
Tailwater depth ( T W TW T W ) at the outlet.
Energy Equation: The headwater depth ( H W HW H W ) is calculated using the energy equation: H W = H + h o − L S 0 HW = H + h_o - L S_0 H W = H + h o − L S 0 Where:
- H H H = Total head loss (ft)
- h o h_o h o = Equivalent hydraulic depth at the outlet (ft)
- L L L = Length of the culvert barrel (ft)
- S 0 S_0 S 0 = Slope of the culvert barrel (ft/ft)
The total head loss ( H H H ) is the sum of the entrance loss ( H e H_e H e ), friction loss ( H f H_f H f ), and exit loss ( H o H_o H o ): H = H e + H f + H o = ( 1 + k e + 29 n 2 L R 1.33 ) V 2 2 g H = H_e + H_f + H_o = \left( 1 + k_e + \frac{29 n^2 L}{R^{1.33}} \right) \frac{V^2}{2g} H = H e + H f + H o = ( 1 + k e + R 1.33 29 n 2 L ) 2 g V 2
Where:
- k e k_e k e = Entrance loss coefficient (dimensionless, see table below)
- n n n = Manning's roughness coefficient
- R R R = Hydraulic radius of the full barrel (ft)
- V V V = Mean flow velocity inside the barrel (fps)
g g g = Acceleration due to gravity ( 32.2 ft/s 2 32.2\text{ ft/s}^2 32.2 ft/s 2 or 9.81 m/s 2 9.81\text{ m/s}^2 9.81 m/s 2 )
Inlet Edge / Configuration Entrance Loss Coefficient ( k e k_e k e )
Concrete Pipe:
- Projecting from fill (socket end) 0.2
- Projecting from fill (square cut end) 0.5
- Headwall with socket end of pipe 0.2
- Headwall with square cut end of pipe 0.5
- Headwall with beveled edges 0.2
- Mitered to conform to fill slope 0.7
Corrugated Metal Pipe (CMP):
- Projecting from fill (thin wall) 0.9
- Headwall or headwall with square edge 0.5
- Mitered to conform to fill slope 0.7
Concrete Box Culvert:
- Headwall with square edge (90-deg wingwalls) 0.5
- Headwall with rounded edge (radius = 1/12 D) 0.2
- Wingwalls at 30 to 75 deg (square edge) 0.4
- Determining the Governing Control
Since a culvert can operate under either inlet or outlet control, the design procedure requires calculating the headwater depth for both conditions. The actual operating headwater is the greater of the two calculated values: H W = max ( H W i n l e t , H W o u t l e t ) HW = \max(HW_{inlet}, HW_{outlet}) H W = max ( H W in l e t , H W o u tl e t )
This is because the culvert will naturally operate under the control mechanism that requires a higher energy level (headwater depth) to pass the design discharge.
Tailwater and the h o h_o h o Parameter
Tailwater ( T W TW T W ) is the depth of water in the outlet channel measured relative to the outlet invert. The value of h o h_o h o used in the headwater equation depends on whether the outlet is submerged or unsubmerged:
Submerged Outlet ( T W ≥ D TW \ge D T W ≥ D ): The culvert outlet flows completely full. h o = T W h_o = TW h o = T W
Unsubmerged Outlet ( T W < D TW < D T W < D ): The flow profile at the outlet is transitional. The equivalent hydraulic depth h o h_o h o is approximated as: h o = max ( T W , d c + D 2 ) h_o = \max\left(TW, \frac{d_c + D}{2}\right) h o = max ( T W , 2 d c + D ) Where d c d_c d c is the critical depth (ft) and D D D is the culvert height (ft).
Energy Dissipation and Outlet Protection
When culverts flow under supercritical conditions or pressurized outlet control, discharge velocities at the outlet can be extremely high (often exceeding 10 fps 10\text{ fps} 10 fps ). These velocities can cause severe erosion and scour in the receiving channel, leading to structural failure of the culvert or embankment.
Energy Dissipators: Structures such as riprap aprons, stilling basins (USBR Type III/IV), impact basins, and baffled outlets are designed to reduce velocity and transition the flow safely to the downstream channel.
Riprap Aprons (HEC-14): A simple and widely used energy dissipator. The design parameters include:
Apron Length ( L a L_a L a ): Determined based on the discharge velocity ( V V V ), diameter ( D D D ), and tailwater conditions. For low tailwater ( T W < 0.5 D TW < 0.5D T W < 0.5 D ): L a = 1.7 Q D 1.5 + 8 D L_a = \frac{1.7 Q}{D^{1.5}} + 8D L a = D 1.5 1.7 Q + 8 D For high tailwater ( T W ≥ 0.5 D TW \ge 0.5D T W ≥ 0.5 D ): L a = 3.0 Q D 1.5 + 4 D L_a = \frac{3.0 Q}{D^{1.5}} + 4D L a = D 1.5 3.0 Q + 4 D
Apron Width: Expands from the culvert width to a terminal width at the end of the apron.
Median Stone Size ( d 50 d_{50} d 50 ): Sized to withstand the shear stress of the discharge velocity. A common simplified formula for circular pipes is: d 50 = 0.02 D ( Q D 2.5 ) 1.33 ⋅ ( D T W ) d_{50} = 0.02 D \left( \frac{Q}{D^{2.5}} \right)^{1.33} \cdot \left( \frac{D}{TW} \right) d 50 = 0.02 D ( D 2.5 Q ) 1.33 ⋅ ( T W D ) Riprap must be angular, graded rock placed over a geotextile filter fabric to prevent piping of fine soils underneath.