Study guide
4.2 Barrier Design and Length of Need
PE Civil: Transportation Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Project Management
1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis
2 Chapter 2: Traffic Engineering - Capacity and Flow
2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis
3 Chapter 3: Traffic Engineering - Studies and Safety
3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)
4 Chapter 4: Roadside and Cross-Section Design
4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations
5 Chapter 5: Horizontal Alignment Design
5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions
6 Chapter 6: Vertical Alignment Design
6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures
7 Chapter 7: Intersection Geometry and Layout
7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry
8 Chapter 8: Traffic Signals
8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption
9 Chapter 9: Traffic Control Design
9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones
10 Chapter 10: Geotechnical and Pavements
10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs
11 Chapter 11: Hydrology and Open-Channel Drainage
11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality
12 Chapter 12: Drainage Structures and Systems
12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities
4.2 Barrier Design and Length of Need
Key Takeaways Explain This Topic AI
Barriers are classified by flexibility into three groups: flexible (cable), semi-rigid (w-beam), and rigid (concrete shapes).
The Length of Need (LON) is the minimum length of barrier required upstream from a hazard to shield it from errant vehicles.
For parallel, non-flared barrier installations, the Length of Need (X) is calculated using the formula: X = LR * (LA - DC) / LA.
The runout length (LR) is the distance a vehicle travels after leaving the road before stopping; it varies from 150 to 450+ feet based on design speed.
Crash cushions and end terminals must be crash-tested (e.g., MASH compliant) and categorized as gating or non-gating, redirective or non-redirective.
Last updated: July 2026
Barrier Design and Length of Need
When a roadside hazard cannot be eliminated, relocated, or designed with a breakaway base, engineers must shield it using a traffic barrier . Although barriers prevent vehicles from striking rigid hazards, they are also obstacles. A barrier should only be installed if a collision with it is expected to be less severe than hitting the unshielded hazard.
Barrier Classification and Structural Options
Traffic barriers are classified into three categories based on their lateral deflection during an impact:
Flexible Barriers (e.g., Cable Barrier)
Characteristics : Consist of tensioned steel cables on weak posts, with dynamic deflection of 6 to 10 feet.
Advantages : Impart the lowest deceleration forces on occupants, resulting in fewer injuries. They are inexpensive and maintain sight lines.
Disadvantages : Require significant lateral clearance for deflection. They must be repaired (posts replaced and retensioned) after most impacts.
Semi-Rigid Barriers (e.g., W-Beam and Thrie-Beam Guardrails)
Characteristics : Consist of corrugated steel rails on steel or wood posts, with blockouts to prevent wheel snagging. Deflection is 2 to 5 feet.
Advantages : Offers a good balance of cost, deflection, and deceleration forces. Standard W-beam is the most common barrier in the US.
Disadvantages : Requires moderate maintenance after impacts. Improper mounting height (standard is 31 inches) can lead to vaulting or underrunning.
Rigid Barriers (e.g., Concrete Safety Shapes)
Characteristics : Standard concrete structures (Jersey, F-shape, or single-slope) with virtually zero deflection.
Advantages : Withstands multiple impacts with minimal maintenance. Excellent for narrow medians or shielding rigid structures where deflection is intolerable.
Disadvantages : Imparts the highest deceleration forces on occupants and has high initial costs.
Length of Need (LON) Calculations
The Length of Need ( L O N LON L ON ) is the total length of the barrier system required upstream of the hazard to shield it from an errant vehicle. Determining the correct L O N LON L ON ensures that a vehicle leaving the road at the designated runout angle cannot travel behind the barrier and strike the hazard.
Key Variables in LON Design
To calculate the L O N LON L ON , designers must identify several geometric parameters:
L R L_R L R : Runout Length (feet). The distance an errant vehicle travels after leaving the traveled way. It is determined from AASHTO tables based on design speed and volume.
L A L_A L A : Lateral Distance to Hazard (feet). Distance from the traveled way edge to the far side of the hazard. If the hazard extends beyond the clear zone, L A L_A L A equals the clear zone width.
D C D_C D C : Lateral Distance to Barrier (feet). The distance from the edge of the traveled way to the face of the barrier.
θ \theta θ (or Flare Rate a : b a:b a : b ): The rate at which the barrier is flared away from the roadway. The flare rate is expressed as a ratio 1 / a 1/a 1/ a (e.g., a 1:15 flare means for every 15 feet along the road, the barrier moves 1 foot laterally). Thus, tan θ = 1 / a \tan \theta = 1/a tan θ = 1/ a . If the barrier is parallel to the roadway, the flare rate is 0.
Parallel Barrier LON Formula
For barriers installed parallel to the roadway (no flare, tan θ = 0 \tan \theta = 0 tan θ = 0 ), the formula for the upstream length of need ( X X X ) is: X = L R ( L A − D C ) L A X = \frac{L_R(L_A - D_C)}{L_A} X = L A L R ( L A − D C )
This is the most common equation tested on the PE Civil Transportation exam.
Flared Barrier LON Formula
If the barrier is flared away from the roadway to reduce the required length of barrier or to terminate it further from the traveled way, the formula becomes: X = L A − D C L A L R + tan θ X = \frac{L_A - D_C}{\frac{L_A}{L_R} + \tan \theta} X = L R L A + tan θ L A − D C
If the flare rate is given as a ratio a : b a:b a : b (where b = 1 b = 1 b = 1 and a a a is the run along the road), then tan θ = 1 / a \tan \theta = 1/a tan θ = 1/ a , and the equation is written as: X = L A − D C L A L R + 1 a X = \frac{L_A - D_C}{\frac{L_A}{L_R} + \frac{1}{a}} X = L R L A + a 1 L A − D C
Sample Calculation
Suppose a roadway has a 60 mph design speed ( L R = 300 L_R = 300 L R = 300 ft). A bridge pier is offset 16 feet ( L A = 16 L_A = 16 L A = 16 ft), and a parallel guardrail is offset 6 feet ( D C = 6 D_C = 6 D C = 6 ft).
Using the parallel barrier formula: X = 300 × ( 16 − 6 ) 16 = 300 × 10 16 = 187.5 feet X = \frac{300 \times (16 - 6)}{16} = \frac{300 \times 10}{16} = 187.5\text{ feet} X = 16 300 × ( 16 − 6 ) = 16 300 × 10 = 187.5 feet
Using the parallel formula, at least 187.5 feet of guardrail must be installed upstream to shield the pier.
Barrier End Treatments and Crash Cushions
The upstream end of a guardrail is a major hazard because it can spear a vehicle during a head-on collision. Therefore, all barrier terminals must be fitted with crashworthy end treatments.
End Terminals
Modern end terminals are designed to either absorb the energy of a head-on impact or guide the vehicle away.
Gating vs. Non-Gating : A gating terminal allows a vehicle striking it at an angle to pass ("gate") through the terminal and enter the area behind the guardrail. A non-gating terminal will redirect the vehicle along its face during an angled impact.
Energy-Absorbing Terminals : These terminals feature an impact head that slides down the W-beam during a head-on collision, flattening the steel rail and extruding it away from the vehicle. This process controlledly absorbs the vehicle's kinetic energy.
Crash Cushions (Attenuators)
Crash cushions are used to shield rigid, wide hazards such as toll booths, gore areas at freeway exits, or concrete barrier ends.
Compression-Based (Redirective) : Consist of steel or plastic cells that compress under impact. They contain internal cables that guide the vehicle and prevent it from pocketing or vaulting, redirecting side impacts.
Inertial Barriers (Sand Barrels) : A series of plastic barrels filled with sand. They are non-redirective and work by transferring momentum from the vehicle to the sand. The mass of sand increases closer to the hazard to provide controlled deceleration. Sand barrels are destroyed upon impact and must be completely replaced.