Study guide

2.2 Interrupted Flow on Segment Streets

PE Civil: Transportation Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Project Management

1.1 Quantity and Cost Estimating 1.2 Project Scheduling and CPM 1.3 Engineering Economic Analysis

2 Chapter 2: Traffic Engineering - Capacity and Flow

2.1 Uninterrupted Flow Capacity and Level of Service (LOS) 2.2 Interrupted Flow on Segment Streets 2.3 Intersection Capacity and LOS 2.4 Nonmotorized Facilities Analysis

3 Chapter 3: Traffic Engineering - Studies and Safety

3.1 Traffic Volume, Speed, and Planning Studies 3.2 Traffic Forecasts and Monitoring 3.3 Traffic Safety and Collision Analysis 3.4 Highway Safety and Crash Modification Factors (CMFs)

4 Chapter 4: Roadside and Cross-Section Design

4.1 Forgiving Roadside and Clear Zone Design 4.2 Barrier Design and Length of Need 4.3 Cross-Section Design Elements 4.4 Nonmotorized Design Considerations

5 Chapter 5: Horizontal Alignment Design

5.1 Circular Curve Elements and Calculations 5.2 Design Speed and Superelevation Design 5.3 Horizontal Sight Distance and Obstructions

6 Chapter 6: Vertical Alignment Design

6.1 Grades, Slopes, and Profile Design 6.2 Crest Vertical Curve Geometry and Sight Distance 6.3 Sag Vertical Curve Geometry and Sight Distance 6.4 Vertical Clearance Under Structures

7 Chapter 7: Intersection Geometry and Layout

7.1 At-Grade Intersection Design and Roundabouts 7.2 Intersection Sight Distance and Sight Triangles 7.3 Interchange Ramps and Terminal Geometry

8 Chapter 8: Traffic Signals

8.1 Traffic Signal Timing and Phasing 8.2 Traffic Signal Warrants (MUTCD) 8.3 Traffic Signal Design and Preemption

9 Chapter 9: Traffic Control Design

9.1 Permanent Signing Design and Standards 9.2 Pavement Marking Layout and Rules 9.3 Temporary Traffic Control and Work Zones

10 Chapter 10: Geotechnical and Pavements

10.1 Sampling, Testing, and Soil Stabilization 10.2 Fundamental Soil Properties and Mass Balance 10.3 Compaction, Excavation, and Mass Diagrams 10.4 Flexible and Rigid Pavement Design and ESALs

11 Chapter 11: Hydrology and Open-Channel Drainage

11.1 Rainfall Hydrology and Rational Method 11.2 Open-Channel Flow and Manning's Equation 11.3 Peak Flow Mitigation and Water-Quality

12 Chapter 12: Drainage Structures and Systems

12.1 Culvert Design and Inlet/Outlet Control 12.2 Stormwater Collection Systems and Inlet Capacities

2.2 Interrupted Flow on Segment Streets

Key Takeaways Explain This Topic AI

Two-lane highways are categorized into Class I (mobility focused), Class II (scenic/recreational), and Class III (transition zones), with distinct service measures.

Class I two-lane highway Level of Service is determined by both Average Travel Speed (ATS) and Percent Time-Spent-Following (PTSF), with the worse of the two metrics governing.

Travel speed along urban street segments (S_T) is calculated by dividing segment length (L) by the sum of midblock running time (T_R) and downstream intersection control delay (d): S_T = 3600 * L / (T_R + d).

LOS for urban street segments is determined by comparing the travel speed to the free-flow speed, represented as the Percent of Free-Flow Speed (PFFS).

Last updated: July 2026

Introduction to Interrupted Flow on Segment Streets

Interrupted flow facilities differ fundamentally from uninterrupted ones due to the presence of external control devices (such as traffic signals, stop signs, and yield signs) that periodically interrupt the traffic stream. These interruptions introduce delay and queueing, which are not present in uninterrupted flow. In transportation engineering, segment street analysis covers facilities that experience these periodic interruptions, including two-lane highways (where passing maneuvers are constrained by opposing traffic) and urban street segments (where overall travel speed is heavily influenced by downstream signal delays).

Two-Lane Highways (HCM Chapter 15)

A two-lane highway is a roadway that has one lane in each direction. On these highways, passing maneuvers must be executed in the lane of opposing traffic when gaps permit. Consequently, the capacity and Level of Service (LOS) of two-lane highways are highly sensitive to directional split, volume, and the percentage of no-passing zones.

Classification of Two-Lane Highways

The Highway Capacity Manual (HCM) classifies two-lane highways into three distinct categories based on their primary function and driver expectations:

Class I: Major intercity routes, primary arterials, and daily commuter routes. On these highways, drivers expect to travel at high speeds. Therefore, both Average Travel Speed (ATS) and Percent Time-Spent-Following (PTSF) are used as the primary service measures. The worse-performing of the two metrics determines the overall Level of Service.

Class II: Scenic, recreational, or local access routes where drivers are less concerned with travel speed but still experience frustration from being delayed behind slow-moving vehicles. LOS is determined solely by the Percent Time-Spent-Following (PTSF) .

Class III: Transition segments that pass through moderately developed areas, small towns, or suburban outskirts where speed limits are lower and access points are frequent. LOS is determined by the Percent of Free-Flow Speed (PFFS) , calculated as the ratio of average travel speed to free-flow speed (PFFS = ATS / FFS × 100).

Demand Flow Rate Adjustment (v_p)

To analyze a two-lane highway, the raw hourly volume (V) must be adjusted to equivalent passenger-car conditions. The demand flow rate for directional analysis is computed as:

v_p = V / (PHF × f_G × f_HV)

Where:

V = Hourly traffic volume (veh/h).

PHF = Peak Hour Factor.

f_G = Grade adjustment factor, which accounts for the effect of terrain (level, rolling, or specific grades) on two-lane highway operations.

f_HV = Heavy-vehicle adjustment factor. For two-lane highways, the passenger-car equivalents (E_T and E_R) are different from freeways, reflecting the higher delay caused by heavy vehicles when passing is restricted.

Service Measure Calculations

Average Travel Speed (ATS): The highway length divided by the average travel time of vehicles. It is estimated using the free-flow speed adjusted for flow rate and no-passing zones:

ATS = FFS − 0.00776 · v_p − f_np

Where f_np is the adjustment factor for the percentage of no-passing zones.

Percent Time-Spent-Following (PTSF): The average percentage of time that vehicles travel in platoons behind slow-moving vehicles. It is estimated as:

PTSF = BPTSF + f_d/np + f_HV

Where BPTSF is the base percent time-spent-following, and f_d/np is the adjustment factor for the combined effect of directional split and the percentage of no-passing zones.

  • Two-Lane Highway Class Primary Service Measure(s) LOS A Threshold LOS E Threshold
  • Class I ATS and PTSF (worse governs) ATS > 55 mph AND PTSF <= 35% ATS > 35 mph AND PTSF <= 90%
  • Class II PTSF PTSF <= 35% PTSF <= 90%
  • Class III PFFS (ATS/FFS × 100) PFFS > 91.7% PFFS > 66.7%
  • Urban Street Segments (HCM Chapter 18)

For urban street segments, travel speed is the primary service measure used to define Level of Service. The analysis evaluates a segment bounded by two signalized intersections, taking into account both midblock running speed and downstream control delay.

Segment Travel Speed (S_T)

The average travel speed of vehicles along an urban street segment is computed using the following equation:

S_T = 3600 × L / (T_R + d)

Where:

S_T = Travel speed along the segment (mph).

L = Segment length (miles).

T_R = Midblock running time of vehicles on the segment (seconds). Running time represents the time required to traverse the segment if there were no intersection delay, and is a function of the segment length and the free-flow speed of the street.

d = Control delay at the downstream boundary intersection (seconds).

Urban Street Classifications

Urban streets are categorized into four classes based on their design and functional category:

Class I (Arterial): High-speed arterial streets designed for mobility, with a base free-flow speed (BFFS) of 45 to 55 mph.

Class II (Arterial): Moderate-speed arterial streets with a BFFS of 35 to 45 mph.

Class III (Collector/Sub-Arterial): Low-to-moderate speed arterials or collectors with a BFFS of 30 to 35 mph.

Class IV (Local/Collector): Low-speed local streets or collectors with a BFFS of 25 to 30 mph.

Level of Service (LOS) Determination

The Level of Service of an urban street segment is determined by comparing the travel speed to the free-flow speed, representing the Percent of Free-Flow Speed (PFFS):

PFFS = (S_T / FFS) × 100

Level of Service (LOS) PFFS Threshold Operational Description

A > 85% Free flow; minimal signal delay; highly stable operations.

B > 70% to 85% Stable flow; minor signal delay; good travel speeds.

C > 50% to 70% Stable flow; moderate signal delay; noticeable speed reductions.

D > 40% to 50% Approaching unstable flow; high signal delay; restricted speed.

E > 30% to 40% Unstable flow; very high delay; operations at capacity.

F <= 30% Breakdown flow; stop-and-go queueing; demand exceeds capacity.